Turntables 97 Items

The new Thorens TD 201 is the right choice for anyone looking for a robust, easy to use plug and play turntable. It comes with a smooth running belt drive and a aluminium platter with rubber mat. The new Thorens TP 71 tonearm uses a detachable headshell with preconfigured AT 3600 cartridge.

SPECIAL FEATURES
Using the switchable integrated phono stage the TD 201 can be connected to any amplifier or receiver even if it does not have a specific input for phono devices.

TD 201 Specification

Turntable section
• Drive System Belt Drive
• Motor DC Motor
• Speed 33 1/3 RPM, 45 RPM
• Rotation Speed Variation +/–2%
• Wow and Flutter 0.2%
• Signal-to-Noise Ratio 67dB or higher (A-weighted, 20kHz LPF)
• 60dB or higher (unweighted, 20kHz LPF)
• Platter Aluminum Die-cast
• Diameter of Platter 12", 300mm

Tonearm section Alumi tube
• Type Static Balance, Straight
• Effective Arm Length 8.8", 223.6mm
• Stylus Pressure Range 0 to 4g
• Supported Cartridge Weight 3.5 to 6.0g
• Overhang 18.6mm
• Anti-skating Adjustment Supported

Cartridge section
• Type MM type (Audio-Technica AT3600)
• Stylus Construction Bonded Diamond
• Frequency Response 20Hz to 20kHz
• Channel Separation >18dB
• Channel Balance 2.5dB
• Vertical Tracking Angle 20 degrees
• Supported Load Impedance 47k ohms
• Output Voltage 2.5mV (1kHz, 3.54cm/sec.)
• Stylus Pressure 3.5g +/–0.5g
• Cartridge Weight 5g +/–0.5g
• Head-shell Weight 10g (including Screws, Nuts and Wires)

Analog Output
• Connector RCA Pin jack (Gold-plated)
• Power AC 100 to 240V, 50/60Hz
• Power Consumption 1.5W (less than 0.5W at Standby)
• Overall Dimensions (W x H x D) 420 x 121 x 360 mm
• Weight Approx. 3.9 kg

Manual: https://www.thorens.com/images/downloads/plattenspieler/201/TD201-User-Guide.pdf

New motor, developed exclusively for direct-drive turntables

The TN-4D-SE uses a sleek, brushless DC motor, offering crystal-locked speed accuracy, regulated by a computer-controlled feedback circuit and achieving low wow-and-flutter levels for a direct drive turntable, especially one with such a stylish, low-profile design.

Knife-edge, pivot-point tonearm bearings

In collaboration with SAEC Corporation, a world-famous, high-end tonearm manufacturer, the TN-4D's tonearm employs a knife-edge, pivot-point bearing. Unlike the case for tonearms with conventional bearings, any fine vertical movements encountered by this tonearm actually help in delivering a more dynamic sound with excellent resolution. The S-shaped tonearm also employs a universal headshell fitting, allowing users to quickly and easily swap cartridges/headshells, and supports a wide range of cartridge weights (from 14 - 23g).

Precision anti-skating and stylus-pressure adjustment

As you might expect, the tonearm is equipped with a counterweight, for precise stylus-pressure adjustment, and an anti-skating mechanism.

Pre-installed Oyster cartridge by SUMIKO

The TN-4D-SE comes with a well-regarded Oyster MM cartridge from SUMIKO – a legendary American cartridge manufacturer. Regardless of the type of music, the Oyster cartridge delivers a powerful but insightful performance.

Built-in PHONO EQ amplifier supporting MM cartridges

The TN-4D-SE comes with a built-in PHONO EQ amplifier that allows you to directly connect the turntable to the line-level inputs of your existing hi-fi system. The NJM8080 IC from New Japan Radio Corporation is employed for op-amp duties, bringing up the level of the tiny signals received via the cartridge up to LINE level strength without any loss of quality.

Die-cast aluminium platter

In conjunction with the newly-developed motor, the high inertia, die-cast aluminium platter helps to achieve better speed stability.

Insulating feet with excellent shock absorption

The insulating feet comprise a machined aluminium shell topped with a rubber cushion that is fixed to the high-density MDF plinth. Thanks to their excellent shock absorption characteristics the TN-4D-SE is very resistant to acoustic feedback.

2-speed turntable for 33-⅓ and 45 rpm

The TN-4D-SE supports 33-⅓ and 45 rpm for LP and EP records. Our insistence on quality engineering can even be seen in the construction of the rotary control for start-up/speed selection, formed of machined aluminium.

Features at a glance:
• Direct-drive analog turntable
• Crystal-locked speed stability, thanks to a new brushless DC motor with feedback control
• Die-cast aluminium platter
• Knife-edge, pivot-point tonearm base, designed by high-end tonearm manufacturer SAEC
• Multi-layer piano black or natural walnut veneer finish
• Built-in PHONO EQ amplifier for high-quality sound (PHONO/LINE switchable)
• Audiophile-grade NJM8080 op-amp used in PHONO EQ stage
• 2-speed drive offering 33-⅓ and 45 rpm
• Gold-plated oxidation-resistant output connectors
• Oyster MM cartridge by SUMIKO
• Shock-absorbing insulating feet
• GND terminal
• RoHS compliant
• Included Accessories
• Felt Mat
• EP Adapter
• Counter Weight
• Head-shell (SUMIKO Oyster installed)
• Platter
• Dust Cover
• Hinges × 2
• RCA Audio cable with GND terminal
• AC Adapter (GPE036W-24015)
• Owner's Manual (including Warranty Card)

TURNTABLE FEATURES
• Type: Manual
• Drive method: Direct-drive
• Speed: 33 rpm, 45 rpm
• Wow & flutter: ≤ 0.1%
• Built-in preamp: Yes
• S/N ratio: 67dB
• Cartridge: SUMIKO Oyster
• Cartridge type: MM
• Cartridge output: 4.0mV (1kHz)
• Tracking force: 2.3g
• Cartridge weight: 5.3g
• Including headshell: 15.3g
• Rec. cartridge weight: 4-13g
• Rec. cartridge weight (incl. headshell): 14-23g

AUDIO OUTPUTS
• Output level & impedance phono (MM): 4.0mV (1kHz)
• RCA: 1
• Output level & impedance RCA: 224mV (–13dBV)

ENERGY MANAGEMENT
• Power consumption (standby): 0.5W
• Power consumption: 2W
• AC adapter power
- Input: AC 100 V – AC 240 V, 50/60 Hz
- Output: DC 24 V, 1500 mA

DIMENSIONS AND WEIGHT
• Product height: 11.7cm
• Product width: 42cm
• Product length: 35.6cm
• Product weight: 6.1kg
• Packsize height: 24cm
• Packsize width: 52.5cm
• Packsize length: 43.8cm

New motor, developed exclusively for direct-drive turntables

The TN-4D-SE uses a sleek, brushless DC motor, offering crystal-locked speed accuracy, regulated by a computer-controlled feedback circuit and achieving low wow-and-flutter levels for a direct drive turntable, especially one with such a stylish, low-profile design.

Knife-edge, pivot-point tonearm bearings

In collaboration with SAEC Corporation, a world-famous, high-end tonearm manufacturer, the TN-4D's tonearm employs a knife-edge, pivot-point bearing. Unlike the case for tonearms with conventional bearings, any fine vertical movements encountered by this tonearm actually help in delivering a more dynamic sound with excellent resolution. The S-shaped tonearm also employs a universal headshell fitting, allowing users to quickly and easily swap cartridges/headshells, and supports a wide range of cartridge weights (from 14 - 23g).

Precision anti-skating and stylus-pressure adjustment

As you might expect, the tonearm is equipped with a counterweight, for precise stylus-pressure adjustment, and an anti-skating mechanism.

Pre-installed Oyster cartridge by SUMIKO

The TN-4D-SE comes with a well-regarded Oyster MM cartridge from SUMIKO – a legendary American cartridge manufacturer. Regardless of the type of music, the Oyster cartridge delivers a powerful but insightful performance.

Built-in PHONO EQ amplifier supporting MM cartridges

The TN-4D-SE comes with a built-in PHONO EQ amplifier that allows you to directly connect the turntable to the line-level inputs of your existing hi-fi system. The NJM8080 IC from New Japan Radio Corporation is employed for op-amp duties, bringing up the level of the tiny signals received via the cartridge up to LINE level strength without any loss of quality.

Die-cast aluminium platter

In conjunction with the newly-developed motor, the high inertia, die-cast aluminium platter helps to achieve better speed stability.

Insulating feet with excellent shock absorption

The insulating feet comprise a machined aluminium shell topped with a rubber cushion that is fixed to the high-density MDF plinth. Thanks to their excellent shock absorption characteristics the TN-4D-SE is very resistant to acoustic feedback.

2-speed turntable for 33-⅓ and 45 rpm

The TN-4D-SE supports 33-⅓ and 45 rpm for LP and EP records. Our insistence on quality engineering can even be seen in the construction of the rotary control for start-up/speed selection, formed of machined aluminium.

Features at a glance:
• Direct-drive analog turntable
• Crystal-locked speed stability, thanks to a new brushless DC motor with feedback control
• Die-cast aluminium platter
• Knife-edge, pivot-point tonearm base, designed by high-end tonearm manufacturer SAEC
• Multi-layer piano black or natural walnut veneer finish
• Built-in PHONO EQ amplifier for high-quality sound (PHONO/LINE switchable)
• Audiophile-grade NJM8080 op-amp used in PHONO EQ stage
• 2-speed drive offering 33-⅓ and 45 rpm
• Gold-plated oxidation-resistant output connectors
• Oyster MM cartridge by SUMIKO
• Shock-absorbing insulating feet
• GND terminal
• RoHS compliant
• Included Accessories
• Felt Mat
• EP Adapter
• Counter Weight
• Head-shell (SUMIKO Oyster installed)
• Platter
• Dust Cover
• Hinges × 2
• RCA Audio cable with GND terminal
• AC Adapter (GPE036W-24015)
• Owner's Manual (including Warranty Card)

TURNTABLE FEATURES
• Type: Manual
• Drive method: Direct-drive
• Speed: 33 rpm, 45 rpm
• Wow & flutter: ≤ 0.1%
• Built-in preamp: Yes
• S/N ratio: 67dB
• Cartridge: SUMIKO Oyster
• Cartridge type: MM
• Cartridge output: 4.0mV (1kHz)
• Tracking force: 2.3g
• Cartridge weight: 5.3g
• Including headshell: 15.3g
• Rec. cartridge weight: 4-13g
• Rec. cartridge weight (incl. headshell): 14-23g

AUDIO OUTPUTS
• Output level & impedance phono (MM): 4.0mV (1kHz)
• RCA: 1
• Output level & impedance RCA: 224mV (–13dBV)

ENERGY MANAGEMENT
• Power consumption (standby): 0.5W
• Power consumption: 2W
• AC adapter power
- Input: AC 100 V – AC 240 V, 50/60 Hz
- Output: DC 24 V, 1500 mA

DIMENSIONS AND WEIGHT
• Product height: 11.7cm
• Product width: 42cm
• Product length: 35.6cm
• Product weight: 6.1kg
• Packsize height: 24cm
• Packsize width: 52.5cm
• Packsize length: 43.8cm

2-speed Analog Turntable with Phono EQ and Bluetooth
A wireless turntable for new way of enjoying vinyl records

The TN-280BT is not only a great-sounding turntable for music enthusiastic who wants to enjoy vinyl record from closet or re-issues. It brings you a totally new way of listening to vinyl records with its Bluetooth capability. No extra cost for hi-fi components or complicated wiring is required. Only Bluetooth speakers or headphones you might have for iPhones are required to enjoy the world of vinyl records

The TN-280BT also accommodates a built-in Phono EQ amplifier that provides Line output, and allows you to connect to almost any sound system regardless type of inputs.

The belt-drive motor on the TN-280BT reduces vibration for sweeter, more accurate sound than direct-drive turntables for DJ, while an aluminum die-cast platter and anti-skating system provide a solid foundation for great-sounding playback. The high-performance, upgradable MM cartridge captures every detail on your record, and the static-balanced straight tone-arm ensures clear sound. It’s all housed in a handsome case in black or walnut veneer.

For music enthusiasts who want to hear every sensuous note of their vinyl collection.

Main Features

2-speed Belt-drive turntable
Built-in Bluetooth transmitter
Built-in MM phono equalizer and Phono, Line, and Bluetooth outputs
High-performance MM cartridge included (Made in Japan)
Aluminum die-cast platter
Anti-skating mechanism
High-density MDF cabinet for better vibration and resonance

Specifications
TURNTABLE section
Type Belt Drive
Motor DC Motor
Rotation Speeds 33-1/3, 45 rpm
Deviation of Speed +/-2%
Wow-and-Flutters 0.2%
Signal-to-Noise Ratio more than 67 dB (A-weighted)
60 dB (unweighted, 20kHz, LPF)
Turntable (Platter)
Material Aluminum Die-cast
Diameter 30 cm
Tone-arm section
Type Straight, Static-balanced
Effective Length 223 mm
Stylus Pressure Range 0 to 5 g
Compatible Cartridge 3.5 to 6.5 g
Anti-skating Adjustment Supported
Head-shell and Cartridge sections
Type MM-type
Stylus Shape Elliptical
Mount Half inch
Frequency Response 20Hz to 20kHz
Channel Separation 20dB at 1kHz
Channel Balance 2.0dB
Tracking Force 1.5 to 2.5g
Vertical Tracking Angle 20 degrees
Output Impedance 47k ohms
Output Voltage 4.5 mV (+/-3dB)
Stylus Pressure 2.0 g (+/-0.5 g)
Cartridge Weight 5.7 g (+/- 0.5 g)
Head-shell Weight 10 g (including nuts, screws, and wires)
Analog Output section
Connectors RCA Pin Jack x 1 pair (Chrome-plated)
Output Voltage
PHONO 4.5 mV (+/-3dB)
LINE 120 mV (-13dBV)
Bluetooth section
Range Approx. 10m
Supported Codec SBC

General
Operation Power AC Adapter
Input AC 100-240V, 50/60Hz
Output DC 12V 500mA
Power Consumption 1.5 Watts or less
Standby Power 0.5 Watts or less
Dimensions (W x H x D) 420 × 117× 356 mm / 16.5” x 4.6” x 14.0”
Weight (Net) 4.9 kg / 10.8 lbs.
Operating Temperature +5˚C to +35˚C
Included Accessories
Felt Mat x 1
EP Adapter x 1
Counter Weight x 1
Head-shell x 1 (MM-type cartridge installed)
Turntable (Platter) x 1
Dust Cover x 1
Dust Cover Hinges x 2
RCA Audio Cable x 1
AC Adapter (GPE053A-V120050-Z) x 1
Owner’s Manual (including Warranty Card)

STANTON STX
LIMITED EDITION PORTABLE SCRATCH TURNTABLE
RAZOR SHARP CUTS, RIGHT AWAY

The STX is the only portable turntable that comes with a factory-installed mini Innofader Nano crossfader. Designed to last over 4 million cycles, this buttery-smooth fader and can be easily swapped between left and right positions to accommodate both left-handed and right-handed scratch styles. The independent crossfader Cut-In and Curve knobs deliver an unrivaled level of crossfader customization, allowing DJs to precisely calibrate the crossfader to suit their own style. This level of customization, along with the ultra-stable platter and tonearm, makes it easy to achieve the absolute cleanest cuts possible.

SCRATCH WHENEVER, WHEREVER
Second only to a sharp, ultra-precise crossfader, ease of portability is vital for a portablism-focused turntable. High-quality rechargeable Lithium-ion batteries are included with the STX, providing enough portable power for hours of mobile use.
The batteries can easily be charged by connecting the unit to a computer or wall charger using the USB-C input. For extended scratch sessions, the USB-C input can also be used with external power sources for even more cutting time.
To top everything off (literally), the latching lid also functions as a stackable, latching base, to bring the STX to standard turntable height.

WELL-CONNECTED FOR CREATORS
Performing with beats and loopers is as simple as connecting a smartphone wirelessly with Bluetooth or with the 1/8” stereo input. The USB port with one-touch recording makes it fast and easy to record high-quality session audio for social media content creation, while the stereo RCA outputs allow you to connect external mixers and speakers for live performances.

PERFORMANCE READY
The modification culture is alive and well in the portablism world. Since the inception of this art form, we’ve seen ingenious designs and customizations. The most popular and utilitarian mods are already included on the STX, including a Start/Stop button, an on-board speaker, and a pitch slider with Ultra-Pitch selection switch. These key features allow for inspiring performances right out of the box and provide a solid foundation upon which DJs can further customize to match their own unique portablist style.

Technical Specifications
Connections (1) RCA line-level output (stereo pair)
(1) 1/4” (6.35 mm) stereo headphone output
(1) 1/8” (3.5 mm) stereo headphone output
(1) 1/8” (3.5 mm) stereo input
(1) USB-C port (charges the internal battery)
(1) USB-A port (USB flash drive recordings

Speeds 33 1/3, 45, 78 RPM (45 RPM adapter included)

Power (2) 3.7V Li-ion batteries

Dimensions
(width x depth x height)
13.0” x 13.0” x 4.0” (3.25” without cover attached)
330.2 x 330.2 x 101.6 mm (82.6 mm without cover attached)

Weight 5.3 lbs.
2.4 kg

The Classic Plate is the upper half of the Plate X One. An additional X One is needed.

Suitable for: Numark PT01, Numark PT01 Scratch, Numark PT01 USB
Material: aluminum

Attention: only the plate!
The X One must be ordered separately: item 845663

The Classic Plate is the upper half of the Plate X One. An additional X One is needed.

Suitable for: Numark PT01, Numark PT01 Scratch, Numark PT01 USB
Material: aluminum

Attention: only the plate!
The X One must be ordered separately: item 845663

The Classic Plate is the upper half of the Plate X One. An additional X One is needed.

Suitable for: Numark PT01, Numark PT01 Scratch, Numark PT01 USB
Material: aluminum

Attention: only the plate!
The X One must be ordered separately: item 845663

Analogue HiFi Turntable for Audio Purists

The TURN 2 HiFi turntable is for vinyl purists wanting to immerse themselves in the world of analogue listening pleasure. Vinyl enthusiasts can start using the turntable straight away thanks to the pre-installed, elliptical cartridge from Ortofon.

Smooth belt drive & low-noise DC motor

The precise belt drive on the TURN 2 ensures a consistent platter speed with minimal wow and flutter. The built-in, low-vibration DC motor is extremely quiet meaning the TURN 2 can be ideally set up in listening environments or living rooms. The integrated motor control can be conveniently switched between 33 1/3 and 45 RPM using the speed selector switch, which is located underneath the chassis in keeping with the player’s minimal styling.

Static balanced, straight tone arm with optimal tracking performance

The TURN 2 is fitted with a static balanced, straight tone arm, with an angled headshell and Ortofon cartridge that sits perfectly in the groove of the record. The manual tone arm lift allows the needle to be precisely lowered onto the record. The anti-skating mechanism ensures the best possible tracking performance.

Flexible Headshell Connection

The headshell connection makes TURN 3 a really flexible performer. The GM/SME locking mechanism allows for easy switching between pick-up cartridges mounted on different headshells.

Classy, matt slimline housing with high-quality terminal

Alongside the connection for the external DC power supply, the rear of the TURN 2 features two gold-plated, corrosion-resistant RCA connections and a separate earth connection to prevent the possibility of ground loops. All cable connections are removable, allowing for easy replacement or later upgrade. The heavy MDF plinth has an extremely slimline design and is available in a matt black, red or white finish. A high-inertia die cast aluminium platter with chrome edging harmoniously rounds off the elegant design of the TURN 2.

FEATURES
•Belt-driven Hi-Fi turntable
•Factory fitted with Ortofon OM10 cartridge
•New straight tonearm design with optimal tracking performance
•Manual arm lift
•Low vibration DC motor
•Integrated motor control with Speed-Switch for conveniently selecting
two different speeds 33 / 45 rpm
•External DC power supply
•Die-cast Aluminum Platter with chrome edging
•Anti-Skating Wheel-System
•Gold-plated, corrosion resistant connections (all cables detachable)
•Slim-line wooden Plinth with mat black finish
•Convenient power switch at the side bottom
•Included Accessories: Turntable Platter, Dust Cover, 2x Dustcover hinges, Balance Counter Weight, PHONO RCA Cable, DC power supply with international plugs, Felt Mat, Instruction Manual, Ortofon OM10 cartridge, headshell

TECHNICAL DATA

Turntable Section:
•Type: Belt-Driven Analogue Turntable System
•Drive: Belt drive
•Motor: DC Motor
•Turntable Speeds: 2 speeds (33 1/3, 45)
•Wow and flutter: 0.2% WRMS
•S/N Ratio: >65 dB (a-weight)

Turntable Platter:
•Material: aluminium die-cast
•Diameter: 300 mm
•Weight: 550 g

Tonearm Section:
•Type: Static Balanced Straight Tonearm
•Effective Length: 224 mm
•Overhang: 19 mm
•Tracking Error Angle: 25°
•Tracking Force: 1.5 g
•Applicable Cartridge Weight: 4~6 g (incl. headshell 14~16 g)
•Anti-Skating Range: 0 – 3 g

Terminals: 1x PHONO Out (gold-plated), 1x GND Earth Terminal General:
•Power supply: DC 12 V, 500 mA
•Power Consumption: 6 W
•Dimensions: 420 (W) x 340 (D) x 121 (H) mm (incl. Dust cover)
Weight: Approx. 4.6 kg

Included Accessories:
Turntable Platter, Dust Cover, 2x Dustcover hinges, Balance Counter Weight, PHONO RCA Cable, DC power supply with international plugs, Felt Mat, Instruction Manual, Ortofon OM10 cartridge, headshell

•Quartz-driven DJ turntable with high-torque direct drive
•Powerful motor with more than 1.8 kg/cm torque
•Redesigned metal top panel, tactile buttons and reinforced housing construction

FEATURES
•NEW in the MK2 version:
•Newly developed top panel and reinforced housing construction
•Reworked metallic buttons with improved feel & tactile response
•Precision Pitch with selectable ranges of +/-8 % & +/-16 %
•Tempo reset (Quartz Lock) feature
•Superior finish in deep black metallic
•Quartz-driven DJ turntable with high-torque direct drive
•Designed for professional use
•Powerful brushless DC motor with more than 1.8 kg/cm torque
•Precise motor control with 3 speeds selectable (33 1/3, 45 & 78 rpm)
•Reverse function: switch for forward/reverse playback
•Precision-engineered die-cast aluminium platter with stable rotation
•Statically balanced s-shaped tone arm with hydraulic lift and anti-skating mechanism
•Universal connection for pick-up systems (SME)
•Extendible needle illumination
•Shock-absorbing feet for vibration isolation
•Sturdy, heavy construction with optimized damping features
•Prepared for dust cover (available as optional accessory)
•Incl. platter, OM Black pick-up system (by Ortofon), headshell, slipmat, counterweight, power cord, instruction manual

TECHNICAL DATA

Turntable:
•Type: direct drive turntable
•Drive: quartz-driven high-torque direct drive
•Motor: 8-pol., 3-phase, brushless DC motor
•Turntable speeds: 3 speeds, manual (33 1/3, 45, 78 rpm)
•Starting torque: > 1.8 kg/cm
•Brake time: < 1 sec.
•Start-up / rpm change: < 1 sec.
•Wow and flutter: < 0.2 % WRMS
•Signal-to-noise ratio: > 50 dB (DIN-B)
•Brake system: electronic brake

Platter:
•Material: aluminium die-cast
•Diameter: 332 mm

Tone arm:
•Type: universal, statically balanced, s-shaped
•Effective length: 230.5 mm
•Overhang: 16 mm
•Tracking angle error: < 3°
•Applicable pick-up weight: 3.5 – 8.5 g (incl. headshell 13 – 18 g)
•Anti-skating range: 0 – 7 g

Connections:
•1x PHONO out (gold-plated), 1x GND

General:
•Power supply: AC 115/230 V, 60/50 Hz (EU/US), AC 100 V, 50/60 Hz (JP)
•Power consumption: 12 W
•Dimensions: 450 (w) x 352 (d) x 144 (h) mm
•Weight: appr. 9.8 kg

•Quartz-driven DJ turntable with direct drive motor
•Reinforced construction with optimized damping features
•Redesigned metal top panel and tactile buttons

FEATURES
•NEW in the MK2 version:
•Newly developed top panel and reinforced housing construction
•Reworked metallic buttons with improved feel & tactile response
•Precision Pitch with selectable ranges of +/-8 %
•Superior finish in deep black metallic
•Quartz-driven DJ turntable with direct drive
•Perfect for beginners
•Precise motor control with 2 speeds selectable (33 1/3 & 45 rpm)
•Precision-engineered, die-cast aluminium platter with stable rotation
•Statically balanced s-shaped tone arm with hydraulic lift and anti-skating - mechanism
•Universal connection for pick-up systems (SME)
•Extendible needle illumination
•Shock-absorbing feet for vibration isolation
•Sturdy, heavy construction with optimized damping features
•Prepared for dust cover (available as optional accessory)
•Incl. platter, OM Black pick-up system (by Ortofon), headshell, slipmat, counterweight, power cord, operating instruction manual

TECHNICAL DATA

Turntable:
•Type: direct drive turntable
•Drive: quarz-driven direct drive
•Motor: 8-pol., 2-phase, brushless DC motor
•Turntable speeds: 2 speeds, manual (33 1/3, 45 RPM)
•Starting torque: > 1kg/cm
•Brake time: < 1 sec.
•Start-up / rpm change: < 1 sec.
•Wow and flutter: < 0.15% WRMS
•Signal-to-noise ratio: > 50 dB (DIN-B)
•Brake system: electronic brake

Platter:
•Material: aluminium die-cast
•Diameter: 332 mm

Tone arm:
•Type: universal, statically balanced, s-shaped
•Effective length: 230.5 mm
•Overhang: 16 mm
•Tracking angle error: < 3°
•Applicable pick-up weight: 3.5 – 8.5 g (incl. headshell 13 – 18 g)
•Anti-skating range: 0 - 7 g

Connections:
•1x PHONO out (gold-plated), 1x GND

General:
•Power supply: AC 115/230 V, 60/50 Hz (US/EU)
•Power consumption: 13 W
•Dimensions: 450 (w) x 352 (d) x 144 (h) mm
•Weight: appr. 6.75 kg

Smooth running of the record ensures high sound quality without acoustic disturbances. Our aluminum record stabilizer weighs 420 g and distributes the weight evenly on the record. The increased contact pressure of the vinyl on the turntable ensures more even scanning.

You can use the Stabilizer universally for all turntables. We deliver the weight including a box for safe storage.

Vinyl Care by HHV was developed for the special needs of passionate vinyl collectors. Each product incorporates the experience and wishes that we at HHV have gathered in countless conversations with customers. All Vinyl Care products are delivered in stylish packaging and are also suitable as a gift idea for record lovers.

Our popular aluminium record stabilizer is finally available in the trendy color gold. The 416-gram stabilizer weight can be used universally for all record players. It increases the contact pressure of the record on the platter and thus ensures more even tracking. The stabilizer is supplied in a practical storage box.
We have developed the Vinyl Care by HHV product range especially for vinyl collectors who are looking for practical and stylish care products for their records. All products make excellent gifts.

New Generation Audiophile Entry Level Turntable

Built-in Phono Stage & Electronic Speed Switch – Made in Europe

The stylish CNC-machined plinth of the T1 features no plastic parts and is carefully manufactured to ensure there are no hollow spaces inside, therefore avoiding unwanted vibrations within the chassis. Carrying this philosophy through the design, the glass platter is also a heavy, zero-resonance design. Finally, the purpose-chosen turntable feet also do a good job of isolating the T1 from ambient vibrations around your hi-fi system. In the T1 the motor drives a belt-system, attached to a newly designed sub-platter, which is mounted into an ultra-precise 0.001mm main bearing with a hardened steel axle and brass bushing. The tonearm new tonearm has an effective length of 8.6”. This one-piece aluminium tonearm also features low-friction bearings for absolute accuracy in use. The T1 comes with a pre-adjusted Ortofon OM 5E Moving Magnet cartridge and is ready to use right out of the box. Also super shielded, semi-symmetrical, low-capacitance Pro-Ject phono cables are included.

Compared to the base T1-model, the Phono SB version includes a built-in, Pro-Ject designed, high-quality phono MM stage and an electronic speed switch between 33 and 45 RPM. For the drive system, where most alternative products may use unregulated DC motors with wide speed fluctuations, the T1 Phono SB features our proven system of an electronically regulated, precision-speed AC motor.

In the box:

T1 Phono SB with Ortofon OM 5E cartridge
Connect it E Phono Cable
Felt mat
Dust cover
Adapter for 7“ singles
Power supply
Allen key, stylus pressure gauge

Features
Precision belt-drive with accurately regulated speed stability and electronic 33/45 RPM speed change
Built-in switchable phono stage - no external phono preamp required
Anti-resonant sub-platter design
Heavy 8mm, zero-resonance blasted-glass platter
Precision CNC‘d heavy full chassis: NO hollow spaces, NO plastic
Ortofon OM5e moving magnet pickup
8,6“ highly precise and light aluminium tonearm
Low friction, vibration free tonearm bearing
One-piece tonearm design with integrated headshell
Super shielded, semi-symmetrical, low-capacitance phono cables - purpose designed by Pro-Ject
Vibration absorbing feet
Elegant dustcover with adjustable hinges
Available in High-Gloss Black, Matt White and Walnut
Hand-made in Europe

Technical Specifications
Speed 33,45 (electronic speed change)
Principle Belt drive
Speed variance 33: 0.7% 45: 0.6%
Wow & Flutter 33: 0.25% 45: 0.23%
Platter Heavy 8mm, blasted-glass platter with felt mat
Main bearing Stainless steel/brass
Signal to noise 65dB
Tonearm 8.6” aluminium
Effective arm length 218.5 mm
Overhang 22.0 mm
Effective tonearm mass 8.0 g
Counterweight for mass 5 - 10g (pre-mounted)
Tracking force range 0 - 50mN (17.5 mN pre-adjusted)
Outputs RCA Phono/Line (switchable)
Included accessories dustcover, feltmat, high quality Connect it E RCA Phono cable
Built-in Power Supply 110 - 240V/50, 60Hz; 15 V DC 800mA
Power consumption 4.5 Watt max
Dimensions 415x100x335 mm (WxHxD)
Weight 3.8 kg net

Manual: https://www.project-audio.com/wp-content/uploads/2019/04/PJ-T1-PhonoSB-Manual.pdf

New Generation Audiophile Entry Level Turntable

Built-in Phono Stage & Electronic Speed Switch – Made in Europe

The stylish CNC-machined plinth of the T1 features no plastic parts and is carefully manufactured to ensure there are no hollow spaces inside, therefore avoiding unwanted vibrations within the chassis. Carrying this philosophy through the design, the glass platter is also a heavy, zero-resonance design. Finally, the purpose-chosen turntable feet also do a good job of isolating the T1 from ambient vibrations around your hi-fi system. In the T1 the motor drives a belt-system, attached to a newly designed sub-platter, which is mounted into an ultra-precise 0.001mm main bearing with a hardened steel axle and brass bushing. The tonearm new tonearm has an effective length of 8.6”. This one-piece aluminium tonearm also features low-friction bearings for absolute accuracy in use. The T1 comes with a pre-adjusted Ortofon OM 5E Moving Magnet cartridge and is ready to use right out of the box. Also super shielded, semi-symmetrical, low-capacitance Pro-Ject phono cables are included.

Compared to the base T1-model, the Phono SB version includes a built-in, Pro-Ject designed, high-quality phono MM stage and an electronic speed switch between 33 and 45 RPM. For the drive system, where most alternative products may use unregulated DC motors with wide speed fluctuations, the T1 Phono SB features our proven system of an electronically regulated, precision-speed AC motor.

In the box:

T1 Phono SB with Ortofon OM 5E cartridge
Connect it E Phono Cable
Felt mat
Dust cover
Adapter for 7“ singles
Power supply
Allen key, stylus pressure gauge

Features
Precision belt-drive with accurately regulated speed stability and electronic 33/45 RPM speed change
Built-in switchable phono stage - no external phono preamp required
Anti-resonant sub-platter design
Heavy 8mm, zero-resonance blasted-glass platter
Precision CNC‘d heavy full chassis: NO hollow spaces, NO plastic
Ortofon OM5e moving magnet pickup
8,6“ highly precise and light aluminium tonearm
Low friction, vibration free tonearm bearing
One-piece tonearm design with integrated headshell
Super shielded, semi-symmetrical, low-capacitance phono cables - purpose designed by Pro-Ject
Vibration absorbing feet
Elegant dustcover with adjustable hinges
Available in High-Gloss Black, Matt White and Walnut
Hand-made in Europe

Technical Specifications
Speed 33,45 (electronic speed change)
Principle Belt drive
Speed variance 33: 0.7% 45: 0.6%
Wow & Flutter 33: 0.25% 45: 0.23%
Platter Heavy 8mm, blasted-glass platter with felt mat
Main bearing Stainless steel/brass
Signal to noise 65dB
Tonearm 8.6” aluminium
Effective arm length 218.5 mm
Overhang 22.0 mm
Effective tonearm mass 8.0 g
Counterweight for mass 5 - 10g (pre-mounted)
Tracking force range 0 - 50mN (17.5 mN pre-adjusted)
Outputs RCA Phono/Line (switchable)
Included accessories dustcover, feltmat, high quality Connect it E RCA Phono cable
Built-in Power Supply 110 - 240V/50, 60Hz; 15 V DC 800mA
Power consumption 4.5 Watt max
Dimensions 415x100x335 mm (WxHxD)
Weight 3.8 kg net

Manual: https://www.project-audio.com/wp-content/uploads/2019/04/PJ-T1-PhonoSB-Manual.pdf

Audiophile Entry Level Turntable

A New Generation of Turntable – Made in Europe

The stylish CNC-machined plinth of the T1 features no plastic parts and is carefully manufactured to ensure there are no hollow spaces inside, therefore avoiding unwanted vibrations within the chassis. Carrying this philosophy through the design, the glass platter is also a heavy, zero-resonance design. Finally, the purpose-chosen turntable feet also do a good job of isolating the T1 from ambient vibrations around your hi-fi system. In the T1 the motor drives a belt-system, attached to a newly designed sub-platter, which is mounted into an ultra-precise 0.001mm main bearing with a hardened steel axle and brass bushing – just like our Essential III turntables. The tonearm new tonearm has an effective length of 8.6”. This one-piece aluminium tonearm also features low-friction bearings for absolute accuracy in use. The T1 comes with a pre-adjusted Ortofon OM 5E Moving Magnet cartridge and is ready to use right out of the box. Also super shielded, semi-symmetrical, low-capacitance Pro-Ject phono cables are included.

In the box:
•T1 with Ortofon OM 5E cartridge
•Directly soldered Connect it E Phono Cable
•Felt mat
•Dust cover
•Adapter for 7“ singles
•Power supply
•Allen key, stylus pressure gauge

Features
•Belt-driven
•Anti-resonant sub-platter design
•Heavy 8mm, zero-resonance blasted-glass platter
•Precision CNC‘d heavy full chassis: NO hollow spaces, NO plastic
•Ortofon OM5e moving magnet pickup
•8,6“ highly precise and light aluminium tonearm
•Low friction, vibration free tonearm bearing
•One-piece tonearm design with integrated headshell
•Super shielded, semi-symmetrical, low-capacitance phono cables - purpose designed by Pro-Ject
•Vibration absorbing feet
•Elegant dustcover with adjustable hinges
•Available in High-Gloss Black, Matt White and Walnut
•Hand-made in Europe

Technical Specifications
•Speed 33,45 (manual speed change)
•Principle Belt drive
•Speed variance 33: 0.7% 45: 0.6%
•Wow & Flutter 33: 0.25% 45: 0.23%
•Platter Heavy 8mm, blasted-glass platter with felt mat
•Main bearing Stainless steel/brass
•Signal to noise 65dB
•Tonearm 8.6” aluminium
•Effective arm length 218.5 mm
•Overhang 22.0 mm
•Effective tonearm mass 8.0 g
•Counterweight for mass 5 - 10g (pre-mounted)
•Tracking force range 0 - 50mN (17.5 mN pre-adjusted)
•Included accessories dustcover, feltmat
•Built-in Power Supply 230V 50Hz (US: 110V 60Hz)
•Power consumption 3 Watt max
•Dimensions 415x100x335 mm (WxHxD)
•Weight 3.8 kg net

Manual: https://www.project-audio.com/wp-content/uploads/2020/07/T1_T1_Phono_SB_T1_BT_Manual.pdf

Audiophile Entry Level Turntable

A New Generation of Turntable – Made in Europe

The stylish CNC-machined plinth of the T1 features no plastic parts and is carefully manufactured to ensure there are no hollow spaces inside, therefore avoiding unwanted vibrations within the chassis. Carrying this philosophy through the design, the glass platter is also a heavy, zero-resonance design. Finally, the purpose-chosen turntable feet also do a good job of isolating the T1 from ambient vibrations around your hi-fi system. In the T1 the motor drives a belt-system, attached to a newly designed sub-platter, which is mounted into an ultra-precise 0.001mm main bearing with a hardened steel axle and brass bushing – just like our Essential III turntables. The tonearm new tonearm has an effective length of 8.6”. This one-piece aluminium tonearm also features low-friction bearings for absolute accuracy in use. The T1 comes with a pre-adjusted Ortofon OM 5E Moving Magnet cartridge and is ready to use right out of the box. Also super shielded, semi-symmetrical, low-capacitance Pro-Ject phono cables are included.

In the box:

T1 with Ortofon OM 5E cartridge
Directly soldered Connect it E Phono Cable
Felt mat
Dust cover
Adapter for 7“ singles
Power supply
Allen key, stylus pressure gauge

Features
Belt-driven
Anti-resonant sub-platter design
Heavy 8mm, zero-resonance blasted-glass platter
Precision CNC‘d heavy full chassis: NO hollow spaces, NO plastic
Ortofon OM5e moving magnet pickup
8,6“ highly precise and light aluminium tonearm
Low friction, vibration free tonearm bearing
One-piece tonearm design with integrated headshell
Super shielded, semi-symmetrical, low-capacitance phono cables - purpose designed by Pro-Ject
Vibration absorbing feet
Elegant dustcover with adjustable hinges
Available in High-Gloss Black, Matt White and Walnut
Hand-made in Europe

Technical Specifications
Speed 33,45 (manual speed change)
Principle Belt drive
Speed variance 33: 0.7% 45: 0.6%
Wow & Flutter 33: 0.25% 45: 0.23%
Platter Heavy 8mm, blasted-glass platter with felt mat
Main bearing Stainless steel/brass
Signal to noise 65dB
Tonearm 8.6” aluminium
Effective arm length 218.5 mm
Overhang 22.0 mm
Effective tonearm mass 8.0 g
Counterweight for mass 5 - 10g (pre-mounted)
Tracking force range 0 - 50mN (17.5 mN pre-adjusted)
Included accessories dustcover, feltmat
Built-in Power Supply 230V 50Hz (US: 110V 60Hz)
Power consumption 3 Watt max
Dimensions 415x100x335 mm (WxHxD)
Weight 3.8 kg net

Manual: https://www.project-audio.com/wp-content/uploads/2019/04/PJ-T1-Manual.pdf

Features
•Belt-driven
•Anti-resonant sub-platter design
•Heavy 8mm, zero-resonance blasted-glass platter
•Precision CNC‘d heavy full chassis: NO hollow spaces, NO plastic
•Ortofon OM5e moving magnet pickup
•8,6“ highly precise and light aluminium tonearm
•Low friction, vibration free tonearm bearing
•One-piece tonearm design with integrated headshell
•Super shielded, semi-symmetrical, low-capacitance phono cables - purpose designed by Pro-Ject
•Vibration absorbing feet
•Elegant dustcover with adjustable hinges
•Available in High-Gloss Black, Matt White and Walnut
•Hand-made in Europe

Technical Specifications
•Speed: 33,45 (manual speed change)
•Principle: Belt drive
•Speed variance: 33: 0.7% 45: 0.6%
•Wow & Flutter: 33: 0.25% 45: 0.23%
•Platter: Heavy 8mm, blasted-glass platter with felt mat
•Main bearing: Stainless steel/brass
•Signal to noise: 65dB
•Tonearm: 8.6” aluminium
•Effective arm length: 218.5 mm
•Overhang: 22.0 mm
•Effective tonearm mass: 8.0 g
•Counterweight for mass: 5 - 10g (pre-mounted)
•Tracking force range: 0 - 50mN (17.5 mN pre-adjusted)
•Included accessories: dustcover, feltmat
•Built-in Power Supply: 230V 50Hz (US: 110V 60Hz)
•Power consumption: 3 Watt max
•Dimensions: 415x100x335 mm (WxHxD)
•Weight: 3.8 kg net

Manual: https://www.project-audio.com/wp-content/uploads/2020/07/T1_T1_Phono_SB_T1_BT_Manual.pdf

A New Generation of Turntable

Audiophile Design Pushed to a New Affordable Level

Premium Materials – Stylish Aesthetics – Rich & Lively Sound.

Audiophile Engineering. No Plastic.
The stylish CNC-machined wooden plinth features no plastic parts and is carefully manufactured to ensure there are no hollow spaces inside, therefore avoiding unwanted vibrations within the chassis. Carrying this philosophy through the design, the glass platter is also a heavy, zero-resonance design – again avoiding the flaws of plastic or lightweight steel alternatives.

No corners cut. More sound.
The T1 tonearm is a new model, based on previous Pro-Ject designs. It is now a complete one-piece design, entirely made out of aluminium! Together with the low friction bearings, this guarantees absolute accuracy in use. The integrated headshell won‘t cause any additional vibrations either, and is a big improvement over other detachable, screwed-on or glued-on headshells! The belt driven motor is attached to a newly designed sub-platter, which is mounted into an ultra-precise 0.001mm main bearing with a hardened stainless steel axle and brass bushing. Alongside the electronically controlled motor system, the T1 is therefore able to ensure a smooth, anti-resonant rotational platform for the tonearm and cartridge to ride across.

Audiophile To The Point

Ortofon OM5E - Elliptical stylus for detailed response
Supplied with an Ortofon OM 5E Moving Magnet cartridge, featuring an elliptical diamond stylus tip; this is a true hi-fi playback system with no corners cut.

Connect it E - Semi-balanced phono cable
The T1 comes with our super shielded, semi-symmetrical, low-capacitance phono cables, purpose-designed by Pro-Ject specifically for turntables – not off-the shelf RCA cables.

Made in EU - A new affordable marvel
Made in Europe by a turntable factory with decades of experience, it is a true hi-fi turntable that looks and sounds sublime.

Features:
• Belt-driven
• Built-in phono stage and Bluetooth for wireless use
• Anti-resonant sub-platter design
• Heavy 8mm, zero-resonance blasted-glass platter
• Precision CNC‘d heavy full chassis: NO hollow spaces, NO plastic
• Ortofon OM5e moving magnet pickup
• 8,6“ highly precise and light aluminium tonearm
• Low friction, vibration free tonearm bearing
• One-piece tonearm design with integrated headshell
• Super shielded, semi-symmetrical, low-capacitance phono cables - purpose designed by Pro-Ject
• Vibration absorbing feet
• Elegant dustcover with adjustable hinges
• Available in High-Gloss Black, Satin White and Walnut
• Hand-made in Europe

Technical Specifications:
• Speed: 33,45 (manual speed change)
• Principle: Belt drive
• Speed variance: 33: 0.7% 45: 0.6%
• Wow & Flutter: 33: 0.25% 45: 0.23%
• Platter Heavy: 8mm, blasted-glass platter with felt mat
• Main bearing: Stainless steel/brass
• Signal to noise: 65dB
• Tonearm: 8.6” aluminium
• Effective arm length: 218.5 mm
• Overhang: 22.0 mm
• Effective tonearm mass: 8.0 g
• Counterweight for mass: 5 - 10g (pre-mounted)
• Tracking force range: 0 - 50mN (17.5 mN pre-adjusted)
• Outputs: RCA Line, RCA Phono, Bluetooth
• Included accessories: dustcover, feltmat, power supply, high-quality phono/line RCA cable
• Built-in Power Supply: 110 - 240V/50, 60Hz; 15 V DC 800mA
• Power consumption: 3 Watt max
• Dimensions: 415x100x335 mm (WxHxD)
• Weight: 3.8 kg net

A New Generation of Turntable

Audiophile Design Pushed to a New Affordable Level

Premium Materials – Stylish Aesthetics – Rich & Lively Sound.

Audiophile Engineering. No Plastic.
The stylish CNC-machined wooden plinth features no plastic parts and is carefully manufactured to ensure there are no hollow spaces inside, therefore avoiding unwanted vibrations within the chassis. Carrying this philosophy through the design, the glass platter is also a heavy, zero-resonance design – again avoiding the flaws of plastic or lightweight steel alternatives.

No corners cut. More sound.
The T1 tonearm is a new model, based on previous Pro-Ject designs. It is now a complete one-piece design, entirely made out of aluminium! Together with the low friction bearings, this guarantees absolute accuracy in use. The integrated headshell won‘t cause any additional vibrations either, and is a big improvement over other detachable, screwed-on or glued-on headshells! The belt driven motor is attached to a newly designed sub-platter, which is mounted into an ultra-precise 0.001mm main bearing with a hardened stainless steel axle and brass bushing. Alongside the electronically controlled motor system, the T1 is therefore able to ensure a smooth, anti-resonant rotational platform for the tonearm and cartridge to ride across.

Audiophile To The Point

Ortofon OM5E - Elliptical stylus for detailed response
Supplied with an Ortofon OM 5E Moving Magnet cartridge, featuring an elliptical diamond stylus tip; this is a true hi-fi playback system with no corners cut.

Connect it E - Semi-balanced phono cable
The T1 comes with our super shielded, semi-symmetrical, low-capacitance phono cables, purpose-designed by Pro-Ject specifically for turntables – not off-the shelf RCA cables.

Made in EU - A new affordable marvel
Made in Europe by a turntable factory with decades of experience, it is a true hi-fi turntable that looks and sounds sublime.

Features:
• Belt-driven
• Built-in phono stage and Bluetooth for wireless use
• Anti-resonant sub-platter design
• Heavy 8mm, zero-resonance blasted-glass platter
• Precision CNC‘d heavy full chassis: NO hollow spaces, NO plastic
• Ortofon OM5e moving magnet pickup
• 8,6“ highly precise and light aluminium tonearm
• Low friction, vibration free tonearm bearing
• One-piece tonearm design with integrated headshell
• Super shielded, semi-symmetrical, low-capacitance phono cables - purpose designed by Pro-Ject
• Vibration absorbing feet
• Elegant dustcover with adjustable hinges
• Available in High-Gloss Black, Satin White and Walnut
• Hand-made in Europe

Technical Specifications:
• Speed: 33,45 (manual speed change)
• Principle: Belt drive
• Speed variance: 33: 0.7% 45: 0.6%
• Wow & Flutter: 33: 0.25% 45: 0.23%
• Platter Heavy: 8mm, blasted-glass platter with felt mat
• Main bearing: Stainless steel/brass
• Signal to noise: 65dB
• Tonearm: 8.6” aluminium
• Effective arm length: 218.5 mm
• Overhang: 22.0 mm
• Effective tonearm mass: 8.0 g
• Counterweight for mass: 5 - 10g (pre-mounted)
• Tracking force range: 0 - 50mN (17.5 mN pre-adjusted)
• Outputs: RCA Line, RCA Phono, Bluetooth
• Included accessories: dustcover, feltmat, power supply, high-quality phono/line RCA cable
• Built-in Power Supply: 110 - 240V/50, 60Hz; 15 V DC 800mA
• Power consumption: 3 Watt max
• Dimensions: 415x100x335 mm (WxHxD)
• Weight: 3.8 kg net

A New Generation of Turntable

Audiophile Design Pushed to a New Affordable Level

Premium Materials – Stylish Aesthetics – Rich & Lively Sound.

Audiophile Engineering. No Plastic.
The stylish CNC-machined wooden plinth features no plastic parts and is carefully manufactured to ensure there are no hollow spaces inside, therefore avoiding unwanted vibrations within the chassis. Carrying this philosophy through the design, the glass platter is also a heavy, zero-resonance design – again avoiding the flaws of plastic or lightweight steel alternatives.

No corners cut. More sound.
The T1 tonearm is a new model, based on previous Pro-Ject designs. It is now a complete one-piece design, entirely made out of aluminium! Together with the low friction bearings, this guarantees absolute accuracy in use. The integrated headshell won‘t cause any additional vibrations either, and is a big improvement over other detachable, screwed-on or glued-on headshells! The belt driven motor is attached to a newly designed sub-platter, which is mounted into an ultra-precise 0.001mm main bearing with a hardened stainless steel axle and brass bushing. Alongside the electronically controlled motor system, the T1 is therefore able to ensure a smooth, anti-resonant rotational platform for the tonearm and cartridge to ride across.

Audiophile To The Point

Ortofon OM5E - Elliptical stylus for detailed response
Supplied with an Ortofon OM 5E Moving Magnet cartridge, featuring an elliptical diamond stylus tip; this is a true hi-fi playback system with no corners cut.

Connect it E - Semi-balanced phono cable
The T1 comes with our super shielded, semi-symmetrical, low-capacitance phono cables, purpose-designed by Pro-Ject specifically for turntables – not off-the shelf RCA cables.

Made in EU - A new affordable marvel
Made in Europe by a turntable factory with decades of experience, it is a true hi-fi turntable that looks and sounds sublime.

Features
•Belt-driven
•Built-in phono stage and Bluetooth for wireless use
•Anti-resonant sub-platter design
•Heavy 8mm, zero-resonance blasted-glass platter
•Precision CNC‘d heavy full chassis: NO hollow spaces, NO plastic
•Ortofon OM5e moving magnet pickup
•8,6“ highly precise and light aluminium tonearm
•Low friction, vibration free tonearm bearing
•One-piece tonearm design with integrated headshell
•Super shielded, semi-symmetrical, low-capacitance phono cables - purpose designed by Pro-Ject
•Vibration absorbing feet
•Elegant dustcover with adjustable hinges
•Available in High-Gloss Black, Satin White and Walnut
•Hand-made in Europe

Technical Specifications
•Speed: 33,45 (manual speed change)
•Principle: Belt drive
•Speed variance: 33: 0.7% 45: 0.6%
•Wow & Flutter: 33: 0.25% 45: 0.23%
•Platter Heavy: 8mm, blasted-glass platter with felt mat
•Main bearing: Stainless steel/brass
•Signal to noise: 65dB
•Tonearm: 8.6” aluminium
•Effective arm length: 218.5 mm
•Overhang: 22.0 mm
•Effective tonearm mass: 8.0 g
•Counterweight for mass: 5 - 10g (pre-mounted)
•Tracking force range: 0 - 50mN (17.5 mN pre-adjusted)
•Outputs: RCA Line, RCA Phono, Bluetooth
•Included accessories: dustcover, feltmat, power supply, high-quality phono/line RCA cable
•Built-in Power Supply: 110 - 240V/50, 60Hz; 15 V DC 800mA
•Power consumption: 3 Watt max
•Dimensions: 415x100x335 mm (WxHxD)
•Weight: 3.8 kg net

Manual: https://www.project-audio.com/wp-content/uploads/2019/04/T1_T1_Phono_SB_T1_BT_Manual.pdf

Pro-Ject standard dust cover Type 1, suitable for chassis like Debut, 1, 1.2, Xpression.

Audiophile Plug & Play turntable - Made in Europe!

Built-in phono stage and switchable phono/line output

With a smart tonearm design we were able to combine pure sound quality with an easy setup. Our Plug & Play design with pre-adjusted tracking force and anti-skating for the included Ortofon OM cartridge has saved us costs and is extremely efficient in handling for our customers.

No compromise in sound: On contraire, the lightweight and low friction aluminium tonearm is optimized for the Ortofon cartridge and will bring out its maximum potential. Also the vibration absorbing feet isolate the turntable from the surface it is place on to deliver the best sound possible. The Primary E Phono is equipped with a switchable phono/line output, so it can be run with a dedicated external phono preamp or with the integrated phono preamp connected to a line input (for example AUX, CD, Tuner, Tape, etc.). With intelligent construction and without needless features we were able to keep the price attractive, despite this product being handmade in Europe. This way we‘re able to offer our customers the sound quality they deserve!

In the box:

Primary E Phono with Ortofon OM cartridge
Gold-plated RCA Phono Cable
Felt mat
Dust cover
Adapter for 7“ singles
Power supply
Allen key, stylus pressure gauge

Features
Built-in phono stage
Switchable phono and line output
Belt-drive with synchronous motor
Ortofon quality OM cartridge
Vibration absorbing feet
Machined special composit fibre chassis
Light-weight, high-precision aluminium tonearm
Sapphire tonearm bearing
Gold-plated contacts
Stainless steel bronze bushing
Elegant dust cover with adjustable hinges
Silicon belt with optimum damping
Handmade in Europe

Technical Specifications
Outputs RCA Phono/Line
Speed 33, 45 (manual speed change)
Principle Belt drive
Speed variance 33: 0.8% 45: 0.7%
Wow & Flutter 33: 0.29% 45: 0.27%
Platter 300 mm with felt mat
Main bearing Stainless steel
Tonearm 8.6” aluminium
Effective arm length 218.5 mm
Overhang 22.0 mm
Effective tonearm mass 8.0 g
Counterweight for mass 3 - 7 g (supplied)
Tracking force range 0 - 25mN (18mN pre-adjusted)
Included accessories Dust cover
Power consumption 4.5 Watts max
Dimensions 420 x 112 x 330mm (WxHxD)
Weight 4.0 kg net

Manual: https://www.project-audio.com/wp-content/uploads/2018/09/PJ-Phono-Primary-E-Phono_Userguide-140818.pdf

Features
•Built-in phono stage
•Switchable phono and line output
•Belt-drive with synchronous motor
•Ortofon quality cartridge
•Vibration absorbing feet
•NO plastic
•Machined special composit fibre chassis
•Light-weight, high-precision aluminium tonearm
•Sapphire tonearm bearing
•Gold-plated contacts
•Stainless steel bronze bushing
•Elegant dust cover with adjustable hinges
•Silicon belt with optimum damping
•Hand-made in Europe

Technical Specifications
•Outputs: RCA Phono/Line
•Speed: 33, 45 (manual speed change)
•Principle: Belt drive
•Speed variance: 33: 0.8% 45: 0.7%
•Wow & Flutter: 33: 0.29% 45: 0.27%
•Platter: 300 mm with felt mat
•Main bearing: Stainless steel
•Tonearm: 8.6” aluminium
•Effective arm length: 218.5 mm
•Overhang: 22.0 mm
•Effective tonearm mass: 8.0 g
•Counterweight for mass: 3 - 7 g (supplied)
•Tracking force range: 0 - 25mN (18mN pre-adjusted)
•Included accessories: Dust cover
•Power consumption: 4.5 Watts max
•Dimensions: 420 x 112 x 330mm (WxHxD)
•Weight: 4.0 kg net

Electronic stylus balance

The Measure it E Stylus Tracking Force Gauge is a highly accurate electronic balance that is designed for measuring stylus tracking forces up to 5.0 grams in 0.002 gram increments. Each Measure it E can easily be calibrated using the supplied calibration weight and by pushing a button. Whenever in doubt about the actual amount of pressure on the diamond tip the 4 digit display of this smart tool will help. Armed with precise information about tracking force, your stylus tip wear can be significantly reduced.

Scope of delivery:
• stylus balance
• calibration weight (5 g)
• 2x LR43 (AG12) button cell batteries + 2 pieces as backup
• protection pouch for the meter
• user guide

Features:
• 4 digit LCD display with backlight
• 4 weighing modes
• Wide capacity 0 - 5g
• Calibration weight
• Precision data readouts with low variance
• Auto calibration function
• Auto power off after 30 seconds
• Low power consumption
• Button cell batteries included

Technical Specifications:
• Capacity: 0 - 5g
• Variance: ±0,002g
• Weighting modes: gram (1g = 10mN), ounce (oz), pennyweight (dwt) & carat (ct)
• Display: 4 digit LCD with backlight
• Calibration: auto calibration using a 5g weight
• Auto off: 30 seconds off
• Replacement battery: 2 x LR43 (AG12) button cells, 1,5V
• Operating temperature: +10 - +30° C (50 - 86 degrees Fahrenheit)
• Dimensions (W x H x D): 96 x 21 x 43mm
• Weight: 49g

Spirit level

Spirit level for optimum positioning of a turntable.

Equipment base

Ground it deluxe 1 suitable for:
• Xtension 9 Evolution, Xtension 10 Evolution, Xtension 12 Evolution
• Signature 10
• RPM 1 Carbon, RPM 3 Carbon, RPM 5 Carbon, RPM 9 Carbon, RPM 10 Carbon

Features:
• Resonance free placement for turntables & hifi
• Heavy weight base filled with granular damping
• 2 models with adjustable spikes (3 or 4 may be fitted)
• 1 model with height adjustable magnetic feet
• Dark grey piano lacquer finish
• Matches charcoal finish of Pro-Ject turntables

Technical Specifications:
• Dimensions: 500 x 65 (45)x 400 mm incl spikes (without spikes)
• Weight: 11,6 kg

Dust protection cover

Cover it 1 is a crystal clear acrylic cover for turntables. It protects the turntable & its needle and suits for:
• Ground it deluxe 1
• Ground it deluxe 3
• Ground it Carbon

Turntables:
• Signature 10
• RPM 10 Carbon
• and all smaller Turntables

Technical Specifications:
• Dimensions (WHD): 525 x 290 x 425 mm (Outside)
• Dimensions (WHD): 515 x 285 x 415 mm (Inside)
• Weight 4.3 kg

Cartridge alignment tool

• Tool for cartridge alignment and adjustment
• Special slip-proof tool for defining the turning centre of Pro-Ject tonearms
• Adaptable to accommodate differing tonearm lengths
• Also suitable for other manufacturers’ tonearms
• Suitable for tonearms between 8″ (203mm) and 12″(305mm) effective length

The PLX-500 inherits the layout of the PLX-1000 professional turntable and produces a warm, clear analogue sound. The perfect deck if you want to start playing with vinyl or if you just want to listen to your record collection at home.

Solidly built with excellent vibration damping and precise audio playback, this high-torque deck has a USB out so you can make digital recordings of your vinyl collection in our free rekordbox software. You can also combine the PLX-500 with the rekordbox dvs Plus Pack, a compatible mixer and the RB-VS1-K Control Vinyl to play and scratch with digital files.

EXCELLENT SOUND DESIGN

Just like the PLX-1000, the PLX-500 is built to produce a high-quality vinyl sound. The shortest possible audio routing from the stylus to the outputs reduces distortion, while the phone/line output switch lets you connect directly to your sound system or to powered speakers with no need for an external amplifier.

EASY DIGITAL RECORDING

Record your vinyl collection to high-quality digital files by simply connecting the turntable to your PC or Mac via the USB out.

SMOOTH DJ PLAY

Use the PLX-500 to mix and scratch your vinyl records or combine the turntable with rekordbox dvs, a compatible DJ mixer and the RB-VS1-K Control Vinyl to play and perform with your digital files.

COVER ART DISPLAY

Put your record covers on display while listening to your vinyl thanks to the sleeve stand inside the dust cover.

Included Accessories:
• PLX-500
• Power cord
• USB cable
• Slip mat
• Dust cover
• Adapter for EP records
• Head shell (with cartridge)
• Balance and shell weights
• Audio adaptor cable: 1 Stereo pin plug (female) & 1 Stereo mini plug (male)
• Operating instructions

Specifications:
• Width: 17.72 in
• Height: 6.26 in
• Depth: 14.49 in
• Weight: 23.59 lb

Turntables:
• Drive Method: Servo-type direct drive
• Platter: Aluminium, die-casting diameter: 332 mm
• Motor: 3-phase, brushless DC motor
• Braking System: Electronic brake
• Rotation Speed: 33⅓, 45, 78 rpm
• Rotation Adjustment: Range ±8 %
• Wow and Flutter: < 0.15% WRMS
• Signal-to-Noise Ratio: 50 dB
• Starting Torque: > 1.6 kgf cm
• Start Time: Within 1 sec (at 33⅓ rpm)

Tone Arm:
• Arm Type: Universal type S-shape tone arm, Gimbal-supported type bearing structure, Static balance type
• Overhang: 0.63 in
• Effective Length: 9.07 in
• Tracking Error: Within 3°
• Height Adjustment Range: 0.24 in
• Stylus Pressure Variable Range: 0-4 g (1 scale 0.1 g)
• Cartridge Weight Single: < 9.5 g
• Cartridge type: VM

Terminals:
• Outputs: 1 PHONO/LINE (RCA)
• USB: 1 USB B port

The PLX-500 inherits the layout of the PLX-1000 professional turntable and produces a warm, clear analogue sound. The perfect deck if you want to start playing with vinyl or if you just want to listen to your record collection at home.

Solidly built with excellent vibration damping and precise audio playback, this high-torque deck has a USB out so you can make digital recordings of your vinyl collection in our free rekordbox software. You can also combine the PLX-500 with the rekordbox dvs Plus Pack, a compatible mixer and the RB-VS1-K Control Vinyl to play and scratch with digital files.

EXCELLENT SOUND DESIGN

Just like the PLX-1000, the PLX-500 is built to produce a high-quality vinyl sound. The shortest possible audio routing from the stylus to the outputs reduces distortion, while the phone/line output switch lets you connect directly to your sound system or to powered speakers with no need for an external amplifier.

EASY DIGITAL RECORDING

Record your vinyl collection to high-quality digital files by simply connecting the turntable to your PC or Mac via the USB out.

SMOOTH DJ PLAY

Use the PLX-500 to mix and scratch your vinyl records or combine the turntable with rekordbox dvs, a compatible DJ mixer and the RB-VS1-K Control Vinyl to play and perform with your digital files.

COVER ART DISPLAY

Put your record covers on display while listening to your vinyl thanks to the sleeve stand inside the dust cover.

Included Accessories:
• PLX-500
• Power cord
• USB cable
• Slip mat
• Dust cover
• Adapter for EP records
• Head shell (with cartridge)
• Balance and shell weights
• Audio adaptor cable: 1 Stereo pin plug (female) & 1 Stereo mini plug (male)
• Operating instructions

Specifications:
• Width: 17.72 in
• Height: 6.26 in
• Depth: 14.49 in
• Weight: 23.59 lb

Turntables:
• Drive Method: Servo-type direct drive
• Platter: Aluminium, die-casting diameter: 332 mm
• Motor: 3-phase, brushless DC motor
• Braking System: Electronic brake
• Rotation Speed: 33⅓, 45, 78 rpm
• Rotation Adjustment: Range ±8 %
• Wow and Flutter: < 0.15% WRMS
• Signal-to-Noise Ratio: 50 dB
• Starting Torque: > 1.6 kgf cm
• Start Time: Within 1 sec (at 33⅓ rpm)

Tone Arm:
• Arm Type: Universal type S-shape tone arm, Gimbal-supported type bearing structure, Static balance type
• Overhang: 0.63 in
• Effective Length: 9.07 in
• Tracking Error: Within 3°
• Height Adjustment Range: 0.24 in
• Stylus Pressure Variable Range: 0-4 g (1 scale 0.1 g)
• Cartridge Weight Single: < 9.5 g
• Cartridge type: VM

Terminals:
• Outputs: 1 PHONO/LINE (RCA)
• USB: 1 USB B port

Ortofon SB-2 Stroboscope
Ortofon SB-2 stroboscope and matching light source is essential for anyone with a turntable to precisely tune the speed of the turntable's rotation for listening to vinyl and can be used with any turntable where you can adjust the speed, including by way of moving an external motor or with a speed box that allows for fine tuning.

This fine tuning kit comes with a stroboscope record and light source. Simply place the stroboscope record on your turntable, turn on the motor and fine tune the speed whilst shining the light source onto the stroboscope record for an indication of when speed is correct. Includes rings for setting of both for 33 rpm and 45 rpm speeds and a switch for testing speed on either 50 Hz or 60 Hz motors.

As speed is a critical factor in getting the best sound from your vinyl, this is an essential analogue accessory.

Technical data
Dimension - 67 mm (W) x 68 mm (L) x 22 mm (H)
Weight - 130g (with battery)
Disc dimension - 100 mm (dia) x 1.0 mm (t)
Disc material - Stainless steel
Revolutions synchronised - 78 rpm, 45 rpm, 33-1/3rpm
Housing material - Aluminum extrusion
Battery - 2 x 1.5V (UM4)
Accuracy of oscillation circuitry - 1/100 Hz , (0.1%)

Ortofon’s new Test Record is designed to allow you to verify your HiFi system in the most natural audio surroundings at home. The Test Record contains special test signals developed for analyzing cartridge performance as well as its interaction with your tonearm and turntable.

Before testing your cartridge, please verify the HiFi system’s functionality. The left speaker should be connected to the left amplifier channel and vice versa; both speakers should work in phase and be optimally positioned in the room.
The Test Record is designed to be played through your system with in-built RIAA equalization. Volume control is recommended to be set at a moderate signal level.

Please refer to your turntable and tonearm’s instructions for correct installation and alignment, adjust tonearm to be parallel to record surface, set Vertical Tracking Force and antiskating according to the cartridge’s recommended technical data, and adjust stylus overhang.

The new 15-track fine pressing

Each side of the record consists of 15 tracks which have been cut from 1-4 and 5-15:

1. Frequency Sweep Left Channel 800 Hz – 50 kHz. Log. 28 sec. Linear cut* (800 – 20000 Hz ±1,5 dB)
2. Frequency Sweep Right Channel 800 Hz – 50 kHz. Log. 28 sec. Linear cut* (800 – 20000 Hz ±1,5 dB)
3. Frequency Sweep Left Channel 800 Hz – 50 kHz. Log. 28 sec. Linear cut* (800 – 20000 Hz ±1,5 dB)
4. Frequency Sweep Right Channel 800 Hz – 50 kHz. Log. 28 sec. Linear cut* (800 – 20000 Hz ±1,5 dB)
5. Reference tone 1000 Hz 5 cm/sec rms Left
6. Reference tone 1000 Hz 5 cm/sec rms Right
7. Reference tone 1000 Hz 5 cm/sec rms Left
8. Reference tone 1000 Hz 5 cm/sec rms Right
9. Tracking ability, lateral 50 ?m peak
10. Tracking ability, lateral 60 ?m peak
11. Tracking ability, lateral 70 ?m peak
12. Tracking ability, lateral 80 ?m peak
13. Tracking ability, lateral 90 ?m peak
14. Tracking ability, lateral 100 ?m peak
15. Square Wave Form 2.7 msec duty cycle 3:7
* The record has a constant velocity amplitude throughout the sweep.

1-4 Frequency sweep – a tool for checking frequency response
There are several factors which can affect frequency response, including cable capacitance, cartridge loading, tracking force and worn parts. Because of this, it can be difficult to achieve perfectly flat frequency response. Sometimes by making small compromises in the cartridge loading, a better overall frequency response can be achieved. Considering the above the signal must be clean throughout the sweep.

5-8 Reference tone for testing channel output
With this standard reference signal is it possible to check the correctness of the connections of the left and right channels, channel balance and speed of the turntable.

9 -14 Tracking ability test, 315 Hz lateral modulation
These tracks contain a 315 Hz signal, recorded at increasing pick amplitudes of 50, 60, 70, 80, 90 and 100 micrometers. Please refer to your cartridge’s tracking ability value specified in the technical data sheet. Your cartridge should be able to track the actual level without audible distortion. Inability to track can be heard as a departure from a pure tone or a sputtering and intermittent tone. To determine if it is one or both channels, the balance control can be utilized. In case of differing tracking ability in the left and right channels it is probably necessary to readjust the anti-skating correction of the tonearm. If both channels fail to track properly, then vertical tracking force should be increased until no further improvement of tracking force can be obtained.

15. Square Wave Form 2.7 msec duty cycle 3:7
When monitoring the output of your cartridge with an oscilloscope you’ll then see a square wave located precisely above each other if the connection from the cartridge is correct.

After successful completion of the above test procedures, you can ensure that your cartridge is optimized. Still the human ear is very sensitive to difference in tone distortion; its level depends on the stylus condition and record wear.

To maintain optimal sound reproduction and to minimize wear on your records as well as on your stylus, we recommend the following procedure before and after each playback:
• Remove dust carefully from record surfaces by using a fine antistatic brush or cloth before every use.
• Please remember to remove dust from the diamond tip before and after playback of each record
• I order to keep electrical contacts clean and to lubricate the knurled nut on the tonearm, Ortofon recommends occasionally a light spray of contact cleaner like DeoxIT ®Gold G-Series into the tonearm socket.

It should be noted that some phono equalizers may generate some tone distortion, which cannot be referred to the cartridge.

User Guide: https://www.ortofon.com/media/148619/ortofon-test-record-user-guide.pdf

Turntable with 4 speakers built-in and bluetooth reception

• Bluetooth 5.0
• 2 rated speed settings 33, and 45 RPM
• Moving Magnetic Cartridge (MMC)
• Belt drive
• Start & stop control
• Tone & Pitch control
• 4 built-in speakers
• Output power: 40W RMS
• Pre-amplifier ON-OFF
• Plastic dust cover
• P.U. leather finishing
• included: CE-UK multiplug AC Adaptor
• Connections: RCA output, AUX in, 3,5mm earphone jack
• Power source : AC 100~240V 60/50Hz
• Power consumpting max : 35W
• Dim. unit: 425 x 360 x 190 mm (WxDxH)

PROS
•MDF housing
•2 loose speakers
•Selectable speed
•Bluetooth / Auto-stop

PRODUCT INFORMATION
•The Lenco LS-300 is a modern turntable with two loose speakers. Enjoy your favourite vinyl at a single press of a button. Forget complicated music systems, because the Lenco LS-300 effortlessly brings your records to life.

•Whatever the music genre you like listening to, you can change easily from 33 to 45 RPM. The 2 separate wooden speakers are powerful enough to fill any room with music. The turntable also features Bluetooth, making it easy to stream music from your smartphone.

•Lenco is fully aware that you want to treat your vinyl records as gently as possible, so the Lenco LS-300 features auto-stop. This function ensures that the record stops turning. This prevents scratching so that you can enjoy your beloved records for longer. The Lenco LS-300 is supplied with a plastic cover that keeps your Lenco free of dust during brief periods when you are not using your turntable. A CE-UK multi-plug AC power supply comes with the turntable.

SPECIFICATIONS
•SKU: A003105
•Product height: 15.20 cm
•Product depth: 35.00 cm
•Product width: 43.80 cm
•Number of speakers: 2
•Number of RCA outputs: 1
•12V car: Yes
•Power option: Power on/off switch, AC
•Type of drive: Belt drive
•Turntable rpm: 33 rpm, 45 rpm
•GTIN / EAN: 8711902040996
•Material: Wood
•Manufacturer's warranty: 24 months
•Stand-by power consumption (ErP Directive): 1W
•Maximum power consumption: 24W

PROS
•MDF housing
•2 loose speakers
•Selectable speed
•Bluetooth / Auto-stop

PRODUCT INFORMATION
•The Lenco LS-300 is a modern turntable with two loose speakers. Enjoy your favourite vinyl at a single press of a button. Forget complicated music systems, because the Lenco LS-300 effortlessly brings your records to life.

•Whatever the music genre you like listening to, you can change easily from 33 to 45 RPM. The 2 separate wooden speakers are powerful enough to fill any room with music. The turntable also features Bluetooth, making it easy to stream music from your smartphone.

•Lenco is fully aware that you want to treat your vinyl records as gently as possible, so the Lenco LS-300 features auto-stop. This function ensures that the record stops turning. This prevents scratching so that you can enjoy your beloved records for longer. The Lenco LS-300 is supplied with a plastic cover that keeps your Lenco free of dust during brief periods when you are not using your turntable. A CE-UK multi-plug AC power supply comes with the turntable.

SPECIFICATIONS
•SKU: A003105
•Product height: 15.20 cm
•Product depth: 35.00 cm
•Product width: 43.80 cm
•Number of speakers: 2
•Number of RCA outputs: 1
•12V car: Yes
•Power option: Power on/off switch, AC
•Type of drive: Belt drive
•Turntable rpm: 33 rpm, 45 rpm
•GTIN / EAN: 8711902040996
•Material: Wood
•Manufacturer's warranty: 24 months
•Stand-by power consumption (ErP Directive): 1W
•Maximum power consumption: 24W

PROS
•Modern turntable
•Bluetooth
•33 or 45 RPM

PRODUCT INFORMATION
•The Lenco LBT-188 is a turntable with Bluetooth functionality. Connecting this turntable to your Bluetooth speaker is child’s play. The ideal set-up for enjoying a full and warm sound while lounging on your couch at home. Retrieve your old records from the attic and play them on this modern turntable. Enjoy the crystal-clear sound of your vinyl, both old and new. Switch from 33 to 45 revolutions to play your vinyl record at the right speed.

•The LBT-188 from Lenco features a metal turntable, belt drive, an RCA connection and a tone arm with a counterweight. The plastic cover ensures that your turntable does not disappear under a layer of dust and protects it against knocks. A CE-UK multi-plug AC power supply comes with the turntable.

SPECIFICATIONS
•SKU: A003117
•Product height: 12.40 cm
•Product depth: 34.40 cm
•Product width: 41.70 cm
•Number of RCA outputs: 2
•12V car: Yes
•Power option: Power on/off switch
•USB connectors: USB A
•Type of drive: Belt drive
•Turntable rpm: 33 rpm, 45 rpm
•GTIN / EAN: 8711902041139
•Amplifier options: Includes (pre) amplifier
•Material: Plastic
•Manufacturer's warranty: 24 months
•Maximum power consumption: 5 W

PROS
•Modern turntable
•Bluetooth
•33 or 45 RPM

PRODUCT INFORMATION
•The Lenco LBT-188 is a turntable with Bluetooth functionality. Connecting this turntable to your Bluetooth speaker is child’s play. The ideal set-up for enjoying a full and warm sound while lounging on your couch at home. Retrieve your old records from the attic and play them on this modern turntable. Enjoy the crystal-clear sound of your vinyl, both old and new. Switch from 33 to 45 revolutions to play your vinyl record at the right speed.

•The LBT-188 from Lenco features a metal turntable, belt drive, an RCA connection and a tone arm with a counterweight. The plastic cover ensures that your turntable does not disappear under a layer of dust and protects it against knocks. A CE-UK multi-plug AC power supply comes with the turntable.

SPECIFICATIONS
•SKU: A003117
•Product height: 12.40 cm
•Product depth: 34.40 cm
•Product width: 41.70 cm
•Number of RCA outputs: 2
•12V car: Yes
•Power option: Power on/off switch
•USB connectors: USB A
•Type of drive: Belt drive
•Turntable rpm: 33 rpm, 45 rpm
•GTIN / EAN: 8711902041139
•Amplifier options: Includes (pre) amplifier
•Material: Plastic
•Manufacturer's warranty: 24 months
•Maximum power consumption: 5 W

Direct drive turntable with USB recording

• Recording Vinyl music through PC
• Integrated stereo pre-amplifier
• 2 rated speed settings 33 RPM and 45 RPM
• Moving Magnetic Cartridge (MMC)
• Mechanical arm lift
• Direct drive
• Removable plastic dust cover
• Included: USB cable, RCA cable
• Connection: USB-PC, RCA line output
• Measurements: 415 x 150 x 333 mm

Direct drive turntable with USB recording

• Recording Vinyl music through PC
• Integrated stereo pre-amplifier
• 2 rated speed settings 33 RPM and 45 RPM
• Moving Magnetic Cartridge (MMC)
• Mechanical arm lift
• Direct drive
• Removable plastic dust cover
• Included: USB cable, RCA cable
• Connection: USB-PC, RCA line output
• Measurements: 415 x 150 x 333 mm

PROS
•USB port
•Removable plastic cover and built-in stereo preamp
•Mechanical tonearm lifter

PRODUCT INFORMATION
•Its trendy design and modern technology make this turntable perfect for all enthusiasts. The Lenco L-3808 is available in 4 colours: white,black, silver and matt grey.

•Do you want to play your favourite sounds of the past for your children? The Lenco L-3808 produces a superb high-quality sound. Your children will be amazed. Because this midi turntable is so easy to use, you can even let them play a record. The Lenco L-3808 is equipped with a mechanical tonearm lifter, a moving magnet cartridge (MMC) and a built-in preamp. You can play records at two speeds: 33 RPM and 45 RPM. A removable plastic cover protects the turntable from dust.

•As the years have passed, your records may have become old and fragile. To prevent your favourite music being lost for ever, you can digitise your cherished vinyl collection using the Lenco L-3808. Connect the turntable to your computer via the USB port and the job will be done in next to no time. Wherever you go, you will always have your favourite music with you.

SPECIFICATIONS
•SKU: A003073
•Product height: 15.10 cm
•Product depth: 34.80 cm
•Product width: 44.80 cm
•Number of RCA outputs: 1
•Power option: non-detachable AC-cable, Power on/off switch, AC
•USB connectors: USB A
•Type of drive: Direct drive
•Turntable rpm: 33 rpm, 45 rpm
•GTIN / EAN: 8711902040637
•Amplifier options: Includes (pre) amplifier, Pre-set Equaliser
•Functional storage media: USB support
•Material: Plastic
•Manufacturer's warranty: 24 months
•Maximum power consumption: 11W

The Gemini TT-4000 High Torque direct drive turntable features a redesigned chassis with reinforced cabinet construction. The TT-4000 uses a precision-machined die-cast aluminum platter for a stable stand in the club. The shock-absorbing rubber feet absorb shock or vibration during operation.

It is ideal for DJs, audiophiles and casual listeners alike. The 16-pole brushless 3-phase DC motor drives the TT-4000's direct drive. The turntable features precise pitch control of +/- 10%. A statically balanced S-shaped tonearm features a hydraulic lift and anti-skate mechanism.

For those who want to digitize their record collection, the Gemini TT-4000 offers a USB port for connection to PC/Mac. This way you can easily record and digitize your vinyl albums.

Thanks to a built-in phono preamp that allows for a line-level output, the TT-4000 does not require grounding.

Features:
• Direct drive turntable with very powerful torque
• Ideal for DJing, listening to music or digitizing
• USB port for connection to PC/Mac
• Very strong torque of 4.5 kg/cm
• Balanced tonearm in S-shape
• Damped rubber feet absorb shocks and vibrations
• Phono preamp with line output built in - no grounding required
• Pitch control of +/- 10%

Technical data:
• Direct driven DC motor with high torque (4.5 kg/cm)
• Signal-to-noise ratio: 40 dB
• Turntable weight: 523 g
• Pitch adjustment: +/- 10%
• Audio interface: USB 2.0 | sampling rate: 48k, 44.1k, 16 bit
• Power consumption: approx. 5.5 W
• Power supply: AC 115V - 60Hz | 230V - 50Hz
• Weight: 6.35 kg
• Dimensions (W x D x H): 490 x 315 x 262 mm

Scope of delivery:
• Gemini TT-4000 Turntable
• Power cable
• RCA cable
• Headshell with pickup/stylus
• Slipmat
• 45 adapters
• User manual & warranty information
• Audacity Software CD V2.1.3

Smooth vinyl precision.

ELAC’s Miracord 50 Turntable is designed to deliver exceptional vinyl transcription, inspired by the iconic Miracord name from the Golden Age of Stereo, when turntables reigned supreme. The Miracord 50 is carefully engineered with a belt-drive motor and die-cast aluminum platter. A precision static balanced, straight-tube tonearm with removable headshell features a factory-mounted MM phono cartridge. Designed with convenience in mind, the Miracord 50 is equipped with a built-in defeatable phono preamplifier, allowing you to add this turntable to virtually any music system.

SPECIFICATIONS

Turntable Section
• Drive System: Belt drive
• Motor: DC motor
• Selectable Speeds: 33⅓ and 45 rpm
• Motor Servo: Speed rotation and servo system
• Rotation Speed Variation: +/-1%
• Wow and Flutter: 1%
• Signal-to-Noise Ratio: -67 dB or higher (A-weighted) -60 dB or higher (unweighted)
• Platter: Aluminum die-cast
• Platter Diameter: 0 in / 300 mm

Tonearm Section
• Type: Aluminum tube, static-balanced
• Effective Arm Length: 8 in / 223.6 mm
• Stylus Pressure Range: 0 to 0 g
• Cartridge Weight Range: 5 to 6.0 g
• Effective Arm Mass: 4 g
• Overhang: 6 mm
• Offset Angle: 25 degrees
• Anti-Skating: Adjustment Supported
• Main Bearing: Stainless steel

Cartridge Section:
• Type: Audio-Technica AT91 moving magnet
• Stylus Construction: Bonded diamond
• Mount: Half-inch
• Frequency Response: 20 Hz to 20 kHz
• Channel Separation: >18 dB
• Channel Balance: 5 dB
• Vertical Tracking: Angle 20 degrees
• Stylus Pressure: 0 g +/-0.5 g
• Cartridge Weight: 0 g +/-0.5 g
• Headshell Weight: 0 g (including screws, nuts and wires)

Phono Equalizer Amplifier
• Type :Moving magnet (MM)
• Phono Output: 5 mV (1 kHz, 3.54 cm/sec)
• Line Output: 140 mV (-17 dBV)
• Phono/Line: Switchable
• Supported Load Impedance: 47 kΩ

Connector: RCA pin jack including RCA cable accessories
Voltage: 100 to 240 V AC / 50 to 60 Hz
Power Consumption: 1.5 W (less than 0.5 W at standby)
Dimensions: (WXHXD) 5.5 x 16.05 x 14.20
Weight: 12.10 lb

Tech Sheet: https://elac-content.s3.amazonaws.com/uploads/2018/08/Miracord-50-Turntable_8-8-18.pdf

FULLY AUTOMATIC PLUG & PLAY-TURNTABLE

The uncomplicated one from Dual with aspirations. The CS 329 uses sophisticated technology for entry-level analogue music playback.

With Plug & Play, you get a complete, ready-to-use package; all components are pre-assembled and permanently set. Plug in and get started!

As a fully automatic machine, the CS 329 offers ideal convenience. The tonearm swivels, lowers and raises autonomously at the touch of a button. All you have to do is put on the record and press the start button.

DETAILS:
Plinth: MDF - Plastic
• Elastomer vibration absorber integrated inside the feet
• Removable dust cover
Platter: Aluminium Die-cast
• Precise aluminium die-cast
• Heavy rubber mat for resonance damping
Tonearm: Straight, Plug and Play
• Plug & Play: all adjustments are factory fixed
• All functions can be fully automatic or manual
Drive: DC- Motor / Belt
• Rubber mountings for vibration decoupling
• Precision cut belt for lower wow & flutter

TECHNICAL SPECIFICATIONS:
Motor:
• Drive: Belt
• Speed settings: 33/45
• Wow & Flutter: < ±0,12 % (DIN WTD)

Tonearm:
• Auto-Start/-Stop-Function: Automatic
• Bearing: Ball-bearing
• Effective length: 221,5 mm
• Offset Angle: 25,6°
• Overhang: 19 mm
• Type: statically balanced
• Stylus Pressure Range: Fixed
• Cartridge Weight Range: N / A
• Factory installed pick up: Audio-Technica AT91

Platter:
• Material: Aluminium die-cast
• Mat: Rubber 2,5 mm
• Bearing: Hardened steel spindle Brass bushing (inverted)
• Diameter: 297 mm
• Weight (incl. Mat): 667 g

Plinth:
• Material: Plastic / MDF
• Surface finish: Black
• Feet: Ø 62 mm / Elastomer
• Connection: RCA cable (fixed)
• Connection to Phono Input: ✓
• Connection to Line Input: ✓
• Digital Output: ✕
• Dimension, closed dustcover: 435 x 372 x 132 mm
• Dimension, open dustcover: T: 405 mm / H: 390 mm
• Weight: 5 kg
• Power plug AC / DC: External power supply

Manual: https://hifi.dual.de/wp-content/uploads/2022/09/BDA-CS-329_manual_V1_DE_EN.pdf

Fits Pioneer PLX-1000, PLX-500 and Technics SL-1200/1210 Mk1, Mk2, Mk3, Mk4, Mk5, Mk5G & Mk6 turntables. Designed and engineered in the UK. Sleek smoked/clear polycarbonate shell provides high level of protection, preserving the lifespan of your turntable. Simple push fit design shields tone-arm from accidental damage whilst making allowances for cables, your turntable can sit ready for operation. At home, on the road or in the club, Decksaver has your turntable covered.

Weight: 0.633 kg
Cover Dimension 45.6 × 35.5 × 7.5 cm
Fits: Technics SL-1200, SL-1210 (MK1-MK7/GR), Pioneer PLX-1000, PLX-CRSS12 and Mixars LTA/STA, Germini PT1000 turntables

Spend a night listening to a rock opera on vinyl or one of the three other listening options the Rhapsody has to offer. This entertainment center comes equipped with a 3-speed turntable, CD player, AM/FM radio, and a built-in Bluetooth receiver so you can kick back and listen to your music however you’d like! The wood cabinet adds an elegant touch and features a matching lid with metal hinges to help keep dust out while not in use. Built-in stereo speakers sit behind a vintage-inspired fabric grill. With aesthetics inspired by vintage radios and elevated with golden accents, this piece will look like a piece of art on your shelf.

• 3-speed record player (33 1/3, 45 & 78 RPM)
• Plays 7”, 10” or 12” records
• 2 Built-in full-range stereo speakers | 3.5”, 8Ω, 5W
• Built-in Bluetooth Receiver
• NP6 needle
• Belt-driven
• Pitch Control
• Headphone Jack
• Cueing Lever
• CD Player
• AM/FM Radio
• Bluetooth input
• Aux in
• RCA out
• EU & UK AC Power adapter

Dimensions: 35,3 cm (w), 17,8 cm (h), 43,21 cm (d)
Weight: 5.9 kg

This neat record player with a wooden look will easily blend into any kind of interior. The Crosley Gig will be the centre piece in the room, but it’s still modest enough to leave space for the rest.
Round out your mid-century modern decor with functional art from Crosley. Inspired by furniture from the 50s and early 60s, the Gig’s minimalistic design features sleek rounded edges and a faux wood finish with a matte black front face for contrast. Three knobs on the front allow you to easily crank up the volume, adjust pitch, switch between vinyl, aux-in or the built-in Bluetooth receiver, letting you play digital music through the record player. Use the matching speakers or the RCA outputs on the back to easily integrate into your existing music system. The Gig is a complete two-speed turntable system that’s ready to jam right out of the box.

• 2-speed record player (33 1/3 & 45 RPM)
• Plays 7”, 10” or 12” records
• 2 external full-range stereo speakers - 3”, 8Ω, 5W
• Built-in Bluetooth Receiver
• Pre-Mounted Moving Magnet Cartridge
• NP5 diamond needle
• Belt-driven
• Adjustable Pitch Control
• Bluetooth input
• Aux in
• RCA out
• AC power adapter (EU & UK PLUG)
• Dimensions: 43 cm (l), 28 cm (w), 10 cm (h) | Speakers: 18 cm (l), 10 cm (w), 10 cm (l)
• Weight: 5.8 kg

Top quality made affordable
This is the best kid in class, the Crosley C62 is a unique straight-out-of-the-box turntable that's unmatched on the market. It comes with external speakers, aluminum platter, tone arm and adjustable counterweight, built-in Bluetooth receiver and a stylish Walnut finish. This turntable is the perfect way to step up your vinyl game without breaking the bank.
The C62 is designed by Crosley to give record collectors the opportunity to upgrade their record player system for an accessible price.
Created with an eye for interior design the (ready to go, straight out of the box) C62 record player and speakers have a veneer finish and a matt black aluminium tonearm with counter weight. The three anti vibration control feed and sturdy steel platter make the design complete. You can pump up the volume because of the two great quality speakers and NP5 diamond needle.

• 2-speed turntable (Speed 331/3, 45 RPM)
• Plays 7”, 10” or 12” records
• 2 External Full-range speakers: 8Ω 10W x 2 4” speakers
• NP5 Diamond needle
• Adjustable Tonearm Counterweight
• Aluminium Tonearm
• Low-Vibration Synchronous Motor
• Switchable Preamp
• Built-in amplifier
• Bluetooth input
• Belt-driven
• Anti-skate adjustment
• Special turntable feet for effective vibration control
• Dust cover
• Dimensions: 41.9 cm (l), 35.8 (w), 13.3 (h)
• Weight: 5.5 kg
• EU & UK AC Power adapter, DC output 15 V 2.4A
• Power Consumption 70W
• Speed Variance +1.5%
• Wow and Flutter < 0.15%
• Signal to Noise 72 dB
• Downforce Range 3.0-6.0g
• Effective Tonearm Length 8.6” (218.5mm)
• Overhang 0.73

Top quality made affordable
This is the best kid in class, the Crosley C62 is a unique straight-out-of-the-box turntable that's unmatched on the market. It comes with external speakers, aluminum platter, tone arm and adjustable counterweight, built-in Bluetooth receiver and a stylish Walnut finish. This turntable is the perfect way to step up your vinyl game without breaking the bank.
The C62 is designed by Crosley to give record collectors the opportunity to upgrade their record player system for an accessible price. Created with an eye for interior design this record player and speakers have a Walnut or Grey veneer finish and a matt black aluminium tonearm with counter weight. The three anti vibration control feed and sturdy steel platter make the upgrade complete.

• 2-speed turntable (Speed 331/3, 45 RPM)
• Plays 7”, 10” or 12” records
• 2 External Full-range speakers: 8Ω 10W x 2 4” speakers
• NP5 Diamond needle
• Adjustable Tonearm Counterweight
• Aluminium Tonearm
• Low-Vibration Synchronous Motor
• Switchable Preamp
• Built-in amplifier
• Bluetooth input
• Belt-driven
• Anti-skate adjustment
• Special turntable feet for effective vibration control
• Dust cover
• Dimensions: 41.9 cm (l), 35.8 (w), 13.3 (h)
• Weight: 5.5 kg
• EU & UK AC Power adapter, DC output 15 V 2.4A
• Power Consumption 70W
• Speed Variance +1.5%
• Wow and Flutter < 0.15%
• Signal to Noise 72 dB
• Downforce Range 3.0-6.0g
• Effective Tonearm Length 8.6” (218.5mm)
• Overhang 0.73

Tonearm gauge
The easiest way to adjust the cartridge's Tracking Force.

Dustprotector for turntable
The Clearaudio Dustprotector is not only an eye-catcher on your turntable, it also prevents the accumulation of dust on the turntable, so you don't have to clean the platter before using it.

An easy to use tool that quickly corrects undersized spindle holes – fitted with an ergonomic aluminum handle.
Diameter (Ø): 7.3 mm

Flat belt
Drive belt for concept, concept active, Performance DC and Ovation.
Dimension: 160 × 4 × 0,8 mm

Moving Magnet Phono Preamplifier

Enjoy every last detail from your vinyl collection with our highest quality moving magnet phono stage, the Solo Phono Preamplifier.

Vinyl as it's Supposed to Sound
Whether you’re dusting off your record collection or embracing analogue through the vinyl revival, there’s a unique experience to be had from the moment you drop the needle on your favourite album. To preserve the unique warmth of the vinyl sound, the Solo phono preamplifier has been carefully designed with a state-of-the-art switch mode power supply and a new surface mounted circuit board layout to reduce unwanted noise.

Why Choose a Dedicated Phono Stage?
Due to the low-level signals created by a turntable, not all hi-fi amplifiers will let you connect directly to a record player. The phono preamplifier boosts this signal to something a power amplifier can work with. The challenge at this stage though is that noise can easily be added.
This is why we’ve designed the Solo around exceptional components that deliver the warm and detailed sound that’s synonymous with vinyl, all without distorting the signal from your moving magnet cartridge. The switch mode power supply improves performance by switching outside of audible frequency to drastically reduce hum and new circuit board layout uses surface-mount components to reduce noise.

Attention to Detail
If some records in your collection are a little worse for wear, the subsonic filter will help to eliminate low frequency rumbles that can be caused by imperfections within your vinyl. Combine this with the balance control for handling potential cartridge imbalances in your record player (that can cause a difference between the left and right channels) and the result is a detailed experience with accurate soundstage.

Eco Friendly
The Solo phono preamplifier is green at heart with less than half a watt standby power consumption and auto power down feature if the unit isn’t used after a 20 minute period. This in turn gives the unit the same worldwide voltage for compatibility wherever you are in the world.

Technical specifications:
• MAX POWER CONSUMPTION: 10W
• GAIN @ 1KHZ: 39dB
• NOMINAL OUTPUT: 300mV
• SENSITIVITY FOR NOMINAL OUTPUT: 3.35mV
• EQUIVALENT INPUT NOISE (A-WEIGHTED): ~0.09uV
• RIAA CURVE ACCURACY: +/- 0.65dB 30Hz-20kHz
• SIGNAL TO NOISE RATIO GROUNDED INPUTS REF. 1V OUTPUT (20HZ-20KHZ BW): >90dB
• THD+N 1KHZ (20-20KHZ BW): <0.0025%
• INPUT IMPEDANCE: 47k Ohm
• INPUT CAPACITANCE: 100pF
• OVERLOAD MARGIN: >30dB
• CROSSTALK @10KHZ: >85dB
• DIMENSIONS (H X W X D): 48x176x132 (1.9x6.9x5.2”)
• WEIGHT: 0.68kg/1.5lbs
• WHATS IN THE BOX: Alva Solo Moving Magnet Phono Preamplifier, User Manual, Safety Guide, Mains lead

Moving Coil & Moving Magnet Phono Preamp

Squeeze every inch of detail from your record collection with our highest quality moving magnet and moving coil phono stage, with integrated headphone amp; the Duo Phono Preamplifier.

Vinyl as it's Supposed to Sound
Whether you’re dusting off your record collection or embracing analogue through the vinyl revival, there’s a unique experience to be had from the moment you drop the needle on your favourite album. To preserve the unique warmth of the vinyl sound, the Duo phono preamplifier has been carefully designed with a state-of-the-art switch mode power supply and a new surface mounted circuit board layout to reduce unwanted noise.

Why Choose a Dedicated Phono Preamplifier?
Due to the low-level signals created by a turntable, not all hi-fi amplifiers will let you connect directly to a record player. The phono preamplifier boosts this signal to something a power amplifier can work with. The challenge at this stage though is that noise can easily be added.
This is why we’ve designed the Duo around exceptional components that deliver the warm and detailed sound that’s synonymous with vinyl, all without distorting the signal from your moving magnet cartridge turntable. The switch mode power supply improves performance by switching outside of audible frequency to drastically reduce hum and new circuit board layout uses surface-mount components to reduce noise.

Vinyl. Just for You
Enjoy the warmth of vinyl privately thanks to Duo’s integrated headphone output. Uniquely, we integrated a 6.35mm headphone jack directly into the phono stage, so you can still enjoy your records when there’s no option to play out loud.
The integrated headphone output also means no need to turn on your amplifier just to power your headphones, resulting in a more eco-friendly listening experience.

Attention to Detail
If some records in your collection are a little worse for wear, the subsonic filter will help to eliminate low frequency rumbles that can be caused by imperfections within your vinyl. Combine this with the balance control for handling potential cartridge imbalances in your record player (that can cause a difference between the left and right channels) and the result is a detailed experience with accurate soundstage.

Eco Friendly
The Duo phono preamplifier is green at heart with less than half a watt standby power consumption and auto power down feature if the unit isn’t used after a 20 minute period. This in turn gives the unit the same worldwide voltage for compatibility wherever you are in the world.

Technical specifications:
• MAX POWER CONSUMPTION: 10W
• CARTRIDGE SUPPORT: Moving Magnet | Moving Coil
• GAIN @ 1KHZ: MM: 39dB | MC: 60dB
• NOMINAL OUTPUT: 300mV
• SENSITIVITY FOR NOMINAL OUTPUT: MM: 3.35mV | MC: 305uV
• EQUIVALENT INPUT NOISE (A-WEIGHTED): MM: ~0.09uV | MC: ~0.08uV
• RIAA CURVE ACCURACY: +/- 0.3dB 30Hz-50Hz
• SIGNAL TO NOISE RATIO GROUNDED INPUTS REF. 1V OUTPUT (20HZ-20KHZ BW): MM: >90dB | MC: >70dB
• THD+N 1KHZ (20-20KHZ BW): MM: <0.0025% | MC: <0.20%
• INPUT IMPEDANCE: MM: 47k Ohms | MC: 100 Ohms
• INPUT CAPACITANCE: 100pF
• OVERLOAD MARGIN: >30dB
• CROSSTALK @ 10KHZ: MM: >85dB | MC: 75dB
• DIMENSIONS (H X W X D): 48 x 215 x 159 mm (1.9 x 8.5 x 6.2")
• WEIGHT: 0.95kg (2.1lbs)
• WHATS IN THE BOX?: Alva Duo Moving Coil & Moving Magnet Phono Preamp, User Manual, Safety Guide, Mains Lead

Integrated Stereo Amplifier with (Built-in) Phono-Stage

• 35 Watts Power per Channel – for detailed performance at all volumes, ideal for smaller/medium sized rooms
• Built-In Phono Stage – to plug & play a vinyl turntable
• Slim Timeless Design – classic hi-fi size, with Lunar Grey aluminium trim
• Tone Controls – fine-tune sound to compensate for room dynamics
• Digital Display – white LED, clearly shows; source, volume & menus
• Headphone Socket – full size socket for high-quality after-hours listening
• Front Aux Input – 3.5mm socket to easily connect compatible devices

Sound Comes First
Our AXA35 integrated amp offers 35 watts per channel and has a built-in moving magnet phono stage – perfect for vinyl enthusiasts. A white LED dot matrix display confirms listening source, and separate tone controls mean you can adjust the sound to suit your taste. There’s a large ¼” (6.35mm) headphone socket too, ideal for high-quality listening without disturbing those who might not share your great taste in music.

Your Journey into Sound
AXA35 is the ideal amp to begin listening to music and really appreciating it – hearing detail in familiar tunes you’ve previously missed. That’s down to the toroidal transformer it uses, a tech found higher up our range. Choose a pair of speakers to suit your taste, perhaps they’ve been in the family for years or maybe something from our SX Series.

Release the Wheels of Steel
The built-in phono stage is the ace up AXA35’s sleeve. It means that you can plug a turntable straight in without any extra kit. Moving magnet (MM) compatibility means AXA35 works with a wide variety of turntables – including that vintage one you’ve had your eye on. Soon you’ll be playing the records you’ve been saving for, and planning what to buy next.

Setting the Tone
With separate bass and treble controls, you can fine-tune AXA35’s sound to suit your taste, speakers and room dynamics. The volume level is shown on the LED dot matrix display, and with 35 watts per channel you’ll have plenty of kick for smaller to medium sized rooms.

Wired for Sound
AXA35 is a well-connected amp, with no less than 4 pairs of RCA inputs, plus a pair of phono sockets for a turntable and a pair of recording outputs. There’s a rear USB socket for technical upgrades. Hi-fi quality speaker binding posts (connectors), compatible for banana plugs, mean that thick cable connects securely for an authentic sound.

Designed for Life
As with the rest of AX Series, AXA35 shares our house-style of Lunar Grey minimalist fascia, black steel cabinet and ‘floating’ base. This timeless look enables an upgrade path through our range. A slim build, in the classic 430mm hi-fi width, also means that AXA35 can easily slot, and breathe new life, into a much-loved system.

Technical specifications:
• POWER OUTPUT: 35 Watts (into 8 Ohms)
• THD (UNWEIGHTED): <0.01% @ 1kHz, 80% of rated power <0.15% 20Hz - 20kHz, 80% of rated power
• FREQUENCY RESPONSE (-3DB): 5Hz - 50kHz
• S/N RATIO (REF 1W): >82dB (unweighted)
• INPUT IMPEDANCES: 47k ohms
• POWER AMP DAMPING FACTOR: > 50
• MAX. POWER CONSUMPTION: 260W
• BASS/TREBLE CONTROLS: Shelving, ultimate boost/cut +/- 10dB @ 100Hz and 10kHz
• STANDBY POWER CONSUMPTION: <0.5W
• INPUTS: 4x RCA, 1x Phono, 1 x 3.5mm Aux input (front panel)
• OUTPUTS: Speakers, Rec Out, USB 5V power
• DIMENSIONS (HXWXD): 83 x 430 x 335mm (3.3 x 16.9 x 13.2”)
• WEIGHT: 5.6kg (12.3lbs)
• IN THE BOX: AXA35 Integrated Amplifier, Power Cable, Remote Control, 2 x AAA Batteries

AT618a
Disc Stabiliser

• Holds record firmly in place stabilising the record
• Thick rubber construction
• 600g