Turntables 198 Items

760 g layer weight to stabilize vinyl records.
Ø 70mm

760 g layer weight to stabilize vinyl records.
Ø 70mm

AT-LP120X
Manual Direct-Drive Turntable (Analogue & USB)

• Direct-drive, DC servo motor
• Fully manual operation
• Adjustable dynamic anti-skate control
• Selectable 33/45/78 RPM speeds
• Convert records to digital files via the USB output
• Professional anti-resonance, die-cast aluminium platter with felt mat

Specs:
Turntable

• Type fully manual
• Motor DC servo-controlled
• Speeds 33-1/3 RPM, 45 RPM, 78 RPM
• Pitch Variation +/-8% or +/-16%
• Turntable Platter Die-cast aluminum
• Starting Torque >1.0 kgf.cm
• Braking System Electronic brake
• Wow and Flutter <0.2% WRMS (33 RPM)
• Signal-to-Noise Ratio >50 dB
• Output Level Pre-amp “PHONO”: 4 mV nominal at 1 kHz, 5 cm/sec
Pre-amp “LINE”: 240 mV nominal at 1 kHz, 5 cm/sec
• Phono Pre-Amp Gain 36 dB nominal, RIAA equalized
• USB Function PC or Mac with an available USB port (USB1.1 or higher)
Windows 7 or above, or Mac OS X or above A/D, D/A – 16-bit/44.1 kHz or 48 kHz USB selectable;
Computer interface – USB 1.1 Compliant Windows 7 or above, or MAC OS X or above
• Power Supply Requirements 115/230V AC, 60/50 Hz
• Power Consumption 3W
• Dimensions 141,6 x 452 x 352 (H x W x D mm)
• Weight 8.0kg
• Accessories Included AT-VM95E phono cartridge AT-HS6 headshell 1.9 m (6.2') USB cable dual RCA (male) to dual RCA (male) cable with ground wire counterweight felt mat; dust cover 45 RPM adapter

Cartridge & Stylus
• Replacement Stylus VM95 Series

Video: https://www.youtube.com/watch?v=eXcgF2SY35Q

AT-LP120X
Manual Direct-Drive Turntable (Analogue & USB)

• Direct-drive, DC servo motor
• Fully manual operation
• Adjustable dynamic anti-skate control
• Selectable 33/45/78 RPM speeds
• Convert records to digital files via the USB output
• Professional anti-resonance, die-cast aluminium platter with felt mat

Specs:
Turntable

• Type fully manual
• Motor DC servo-controlled
• Speeds 33-1/3 RPM, 45 RPM, 78 RPM
• Pitch Variation +/-8% or +/-16%
• Turntable Platter Die-cast aluminum
• Starting Torque >1.0 kgf.cm
• Braking System Electronic brake
• Wow and Flutter <0.2% WRMS (33 RPM)
• Signal-to-Noise Ratio >50 dB
• Output Level Pre-amp “PHONO”: 4 mV nominal at 1 kHz, 5 cm/sec
Pre-amp “LINE”: 240 mV nominal at 1 kHz, 5 cm/sec
• Phono Pre-Amp Gain 36 dB nominal, RIAA equalized
• USB Function PC or Mac with an available USB port (USB1.1 or higher)
Windows 7 or above, or Mac OS X or above A/D, D/A – 16-bit/44.1 kHz or 48 kHz USB selectable;
Computer interface – USB 1.1 Compliant Windows 7 or above, or MAC OS X or above
• Power Supply Requirements 115/230V AC, 60/50 Hz
• Power Consumption 3W
• Dimensions 141,6 x 452 x 352 (H x W x D mm)
• Weight 8.0kg
• Accessories Included AT-VM95E phono cartridge AT-HS6 headshell 1.9 m (6.2') USB cable dual RCA (male) to dual RCA (male) cable with ground wire counterweight felt mat; dust cover 45 RPM adapter

Cartridge & Stylus
• Replacement Stylus VM95 Series

Video: https://www.youtube.com/watch?v=eXcgF2SY35Q

This fully manual turntable is modeled after the AT-LP120XUSB, but adds the convenience of Bluetooth® wireless connectivity to the existing analog and USB outputs.

Featuring a specially designed DC servo direct-drive motor and adjustable dynamic anti-skate control, the AT-LP120XBT-USB plays 33-1/3, 45, and 78 RPM records and outputs the high-fidelity audio to the device of your choice. Use the included RCA output cable along with the built-in selectable phono preamp to connect to your home stereo or powered speakers. Use the USB cable to connect to your computer and then download the free Mac- and PC-compatible Audacity recording software, or software of your choice, to start converting your records to digital audio files. Or use the Bluetooth wireless technology to pair the turntable with wireless speakers, headphones or other devices, including those that support the high-quality Qualcomm® aptX™ audio codec.

The turntable also features an S-shaped tonearm with adjustable tracking force and an AT-HS6 universal ½"- mount headshell with an AT-VM95E Dual Moving Magnet™ phono cartridge. Audio-Technica has been a leader in phono cartridge design for more than 50 years, and that expertise shows in the versatile, high-performance AT-VM95E. The cartridge comes with a 0.3 x 0.7 mil elliptical stylus, but is also compatible with any VM95 Series replacement stylus, offering a wide choice of options for every budget and application.

Additional professional features include a die-cast aluminum platter with felt mat; a start/stop button; selectable high-accuracy quartz-controlled pitch lock and pitch change slider control with +/-10% adjustment range; a stroboscopic platter with speed indicator; a removable plug-type stylus target light; external power supply; and a removable hinged dust cover.

High-fidelity audio with Bluetooth® wireless technology

Direct-drive, DC servo motor

Fully manual operation

Adjustable dynamic anti-skate control

Selectable 33/45/78 RPM speeds

Anti-resonance, die-cast aluminum platter with felt mat

AT-HS6 universal ½"-mount headshell and AT-VM95E Dual Moving Magnet™ phono cartridge with 0.3 x 0.7 mil elliptical stylus

AT-VM95E cartridge is compatible with any VM95 Series replacement stylus, offering a wide choice of options for every budget and application

Balanced S-shaped tonearm with hydraulically damped lift control and lockable rest

Connects wirelessly to speakers and other devices equipped with Bluetooth wireless technology, to wired audio systems and powered speakers via included dual RCA output cable, or to computers via included USB cable

Compatible with the high-quality Qualcomm® aptX™ audio codec

Built-in switchable phono preamplifier for phono- or line-level output

Stroboscopic platter with speed indicator

Variable pitch control with quartz speed lock

Removable plug-type target light for easier cueing in low light

Damped base construction for reduced low-frequency feedback coloration

AC adapter handles AC/DC conversion outside of the chassis, reducing noise in the signal chain

Convert your vinyl records to digital audio files by downloading and using the free Mac- and PC-compatible Audacity recording software (or software of your choice)

Includes: USB cable, detachable RCA output cable (dual RCA male to dual RCA male), AC adapter, 45 RPM adapter, counterweight, felt mat, and removable hinged dust cover

Turntable
Bauart 3-speed, fully manual operation
Motor DC servo motor
Antriebsart Direct drive
Geschwindigkeiten 33-1/3 RPM, 45 RPM, 78 RPM
Plattenteller Die-cast aluminum
Anlaufmoment >1.0 kgf.cm
Bremssystem Electronic brake
Gleichlaufschwankung <0.2% (WTD) @ 3 kHz (JIS)
Rauschabstand >50 dB
Output Level Pre-amp “PHONO”: 4 mV nominal at 1 kHz, 5 cm/sec
Pre-amp “LINE”: 240 mV nominal at 1 kHz, 5 cm/sec
Phono-Vorverstärkung 36 dB nominal, RIAA equalized
USB-Funktionen A/D, D/A – 16-bit/44.1 kHz or 48 kHz USB selectable; Computer interface – USB 2.0 Compliant Windows 7 or above, or MAC OS X or above
Betriebsspannung 100 to 240 V, 50/60 Hz, 1.5A Max
Power Consumption 2.75 W
Abmessungen 452.0 mm (17.80") W x 352.0 mm (13.86") D x 141.6 mm (5.57") H
Gewicht 8 kg (17.6 lbs.), without dust cover
Accessories Included AT-VM95E phono cartridge; AT-HS6 headshell; 1.9 m (6.2') USB cable; dual RCA (male) to dual RCA (male) cable with ground wire; counterweight; felt mat; dust cover; 45 RPM adapter; plug-type stylus target light
Tonearm Type Balanced S-shaped tonearm with detachable headshell
Effective Arm Length 230.5 mm
Overhang 16 mm
Tracking Error Angle Less than 3 degrees
Applicable Cartridge Weight 3.5-8.5 g
Anti-skating Range 0-4 g
Replacement Stylus AT-VMN95E
Communication System Bluetooth Version 5.0
Maximum Communication Range Line of sight - approx. 10 m (33')
Compatible Bluetooth Profile A2DP
Support Codec SBC, Qualcomm® aptX™ audio

Manual: https://www.audio-technica.com/media/wysiwyg/product/pdfs/eu/AT-LP120XBT-USB_UM_162501910_V2_EN_web_200826.pdf

The AT-LP140XP fully manual professional DJ turntable features a high-torque direct-drive motor and anti-resonant, mass-damped, die-cast aluminium platter to ensure stable, on-axis rotation at 33-1/3, 45, and 78 RPM. It is equipped with an S-shaped tonearm with height adjustment, adjustable tracking force (counterweight) and adjustable dynamic anti-skate control.

Audio-Technica has been a leader in phono cartridge design for more than 50 years, and that expertise shows in the durable, high-output AT-XP3 DJ cartridge with 0.6 mil conical bonded stylus included with the turntable. It comes pre-mounted to an AT-HS6 universal ½"-mount headshell.

Designed to connect to components with a dedicated phono input, the turntable comes with a detachable dual RCA output cable which supplies a strong 5.5 mV phono output.

Additional professional features include a start/stop button; forward and reverse play; selectable high-accuracy quartz-controlled pitch lock and pitch change slider control with +/-8%, +/-16%, and +/-24% adjustment ranges; a stroboscopic platter with speed indicator; a retractable plug-type stylus target light; and a removable hinged dust cover.

Turntable Designed for DJs
This high-torque direct-drive deck comes with a high-output AT-XP3 DJ cartridge and is loaded with professional features.

Take Control
Whether used for DJ gigs or playing records at home, the AT-LP140XP gives you exquisite control over your vinyl listening experience.

Features:
• Experience high-fidelity audio and professional DJ performance
• Direct-drive, high-torque servo motor with speed stabilization
• Fully manual operation
• Adjustable dynamic anti-skate control
• Selectable 33/45/78 RPM speeds
• Professional anti-resonance, mass-damped, die-cast aluminium platter with felt mat
• AT-HS6 universal ½"-mount headshell and AT-XP3 DJ cartridge with 0.6 mil conical bonded stylus
• Balanced S-shaped tonearm with hydraulically damped lift control, height adjustment, and lockable rest
• Dedicated phono-level output (5.5 mV)
• Stroboscopic platter with speed indicator
• Forward/reverse operation and variable pitch control with quartz speed lock
• Retractable plug-type target light for easier cueing in low light
• Popup stylus target light for easier cueing in low light
• Damped base construction for reduced low-frequency feedback coloration
• Includes: detachable RCA output cable (dual RCA male to dual RCA male), power cable, 45 RPM adapter, counterweight, felt mat, and removable hinged dust cover
• Available in black (AT-LP140XPBK) and silver (AT-LP140XPSV)

Specifications:
Turntable
• Type: 3-speed, fully manual operation
• Motor: High-torque DC motor
• Drive: Method Direct drive
• Speeds: 33-1/3 RPM, 45 RPM, 78 RPM
• Turntable Platter: Die-cast aluminium
• Pitch Variation: +/-8% or +/-16% or +/-24%
• Starting Torque: 2.2 kgf-cm
• Wow and Flutter: <0.2% WRMS (33 RPM)
• Signal-to-Noise Ratio: >50 dB
• Output Level: 5.5 mV nominal at 1 kHz, 5 cm/sec
• Power Supply Requirements: 115/230V AC, 60/50 Hz
• Weight: 10.0 kg

Headshell
• Model: AT-HS6
• Weight: 9 g

Tone arm
• Type: Balanced S-shaped tonearm with detachable headshell
• Length: 230.5mm
• Overhang: 16mm
• tracking error: Less than 3 degree
• Tracking weight: 3.5 - 8.5 g
• Anti-skating: 0-4 g

Manual: https://eu.audio-technica.com/resources/AT-LP140XP_UM_162501390_V1_DE_web_190607.pdf

The AT-LP3XBT is a fully automatic turntable designed to deliver outstanding analogue sound with enhanced Bluetooth® wireless technology.

Bringing the clarity and warmth of analogue audio to the digital generation, this Bluetooth® turntable offers all the benefits of vinyl with the convenience of enhanced connectivity. Enjoy the freedom to connect to the latest speakers or headphones with Bluetooth® wireless technology at just the touch of a button - your analogue listening journey starts here.

Audio-Technica’s LP3XBT turntable combines 60 years of high-fidelity design with the latest Bluetooth® technology, giving you cutting-edge features while drawing on decades of audio experience. Enjoy a turntable that’s built on heritage, but built with the modern listener in mind.

Featuring fully automatic operation, a built-in phono preamp, removeable universal headshell and replaceable stylus, this Audio-Technica turntable is easy to set up and use, making it an ideal choice for beginners or those looking to level up their listening experience. Play 33⅓ & 45 RPM records your way, experimenting with different styli as you begin to discover your personal audio preferences.

Integrated Bluetooth® technology gives you the flexibility to connect your turntable quickly and easily, no matter where you are or how you choose to enjoy your vinyl experience. Whether you pair your LP3XBT with speakers to provide the perfect soundtrack for a gathering with friends, or listen through a pair of Audio-Technica headphones for a deep listening session, you can expect impeccable high-fidelity audio.

Features:
• Fully automatic belt-drive turntable operation with two speeds: 33-1/3, 45 RPM
• High-fidelity audio with Bluetooth wireless technology
• Connects wirelessly to speakers and other devices equipped with Bluetooth wireless technology or to wired audio systems and powered speakers via included dual RCA output cable
• Compatible with the high-quality Qualcomm® aptX™ audio codec
• Balanced straight tonearm with hydraulically damped lift control and rest
• AT-VM95C cartridge is compatible with any VM95 Series replacement stylus, offering a wide choice of options for every budget and application
• Includes the AT-HS3 universal headshell
• Built-in switchable phono/line pre-amplifier with detachable dual RCA output cable with grounding wire
• Anti-resonance, die-cast aluminum platter with felt mat
• Damped base construction for reduced low-frequency feedback coloration
• Included Accessories: detachable RCA output cable (Dual RCA male to dual RCA male with ground), 45 RPM adapter, removable hinged dust cover, and detachable power cable

Specifications:
• Type Belt-drive, fully automatic operation
• Motor DC motor
• Drive Method Belt drive
• Speeds 33-1/3 RPM, 45 RPM
• Turntable Platter Die-cast aluminium
• Wow and Flutter < 0.2 % WRMS (33 RPM) at 3 kHz
• Signal-to-Noise Ratio > 60 dB
• Output Level PHONO: 4.0 mV nominal at 1 kHz, 5 cm/sec
• Output Level LINE: 252 mV nominal at 1 kHz, 5 cm/sec
• Phono Pre-Amp Gain 36 dB nominal, RIAA equalized
• Power Supply Requirements 100 to 240 V, 50/60 Hz, 0.6 A Max
• Power Consumption 2 W
• Dimensions 435.6mm (17") ×374 mm (15 ") ×128 mm (5.0") (W × D × H)
• Weight 5.0 kg (11 lbs)

Accessories Included:
• Dust cover
• Felt mat
• Platter (with drive belt)
• Dust cover hinges
• Counterweight
• Headshell (AT-HS3 BK) with VM stereo cartridge (AT-VM95C)
• 45-RPM adapter
• RCA audio cable (Approx. 1.0 m (3.3'))
• AC adapter (Approx. 1.5 m (4.9'))

Communication:
• Communication System Bluetooth version 5.2
• Frequency Band 2.402 GHz to 2.480 GHz
• Maximum RF Output 2,5 mW EIRP
• Maximum Communication Range Sichtlinie – ca. 10 m
• Modulation Method GFSK, Pi/4DQPSK, 8DPSK
• Compatible Bluetooth Profile A2DP
• Support Codec Qualcomm® aptX™ Adaptive Audio, Qualcomm® aptX™ Audio, SBC

AT-LP5X
Fully Manual Direct Drive Turntable
Building on Audio-Technica’s analogue heritage and over 50 years of Japanese audio design, the AT-LP5x features upgraded technology while keeping the contemporary style and acclaimed performance of its predecessor, the AT-LP5.

The LP5x retains the J-shaped tonearm, a design inspired by the classic Audio-Technica models of the 1960s and ’70s, and features a metallic gimbal suspension system and precision bearings to mitigate tracking errors. The tonearm also includes an adjustable counterweight and anti-skate control and comes fitted with a lightweight (9.3g) AT-HS6 headshell and the black AT-VM95E Dual Moving Magnet stereo cartridge.

Constructed of anti-vibration damping materials with heavy-mass metal chassis inserts, the AT-LP5x turntable has been designed to limit low-frequency acoustical feedback. Its precision-machined, die-cast aluminum platter is powered by a direct-drive, low-noise motor, ensuring stable, on-axis rotation at 33-1/3, 45 and 78 RPM. A 5 mm thick rubber-damping mat, which isolates from low frequency feedback while providing a highly stable surface for all LP formats, tops the platter.

The AT-LP5x features a built-in switchable MM/MC phono/line preamp that enables it to connect directly to a computer, home stereo, powered speakers and other components that have no dedicated turntable input. The selection of MM/MC cartridges allow for an easy upgrade to a moving coil with additional equipment. The turntable is also equipped with a USB output for direct connection to a computer.

Direct-drive, low noise motor
Fully manual operation with three speeds: 33-1/3, 45 and 78 RPM
AT-VM95E Dual Moving Magnet stereo cartridge (black) with replaceable stylus
Lightweight AT-HS6 headshell
J-shaped tonearm, modeled after original Audio-Technica designs from the 1960s and ’70s, are engineered to minimize tracking errors
Switchable MM/MC built-in pre-amplifier and line enables connection to components with or without a dedicated phono input
Anti-resonance, die-cast aluminum platter
Heavy rubber damping mat for improved low-frequency reproduction
AC adapter handles AC/DC conversion outside of the chassis, reducing noise in the signal chain
Elegant matte black finish
Includes dual RCA (male) to dual RCA (male) stereo cable, 45 RPM adapter, USB cable
Included dust cover and mounting hardware

Specifications

Drive Method Direct Drive
Type 3-speed, fully manual operation
Motor DC motor
Speeds 33-1/3 RPM, 45 RPM, 78 RPM
Turntable Platter Die-cast aluminum
Starting Torque >1.0 kgf.cm
Braking System Electronic brake
Wow and Flutter <0.2% WRMS (33 RPM) at 3 KHz
Signal-to-Noise Ratio >50 dB
Output Level PHONO: 4.0 mV nominal at 1 kHz, 5 cm/sec LINE 250 mV nominal at 1 kHz, 5 cm/sec
Phono Pre-Amp Gain 36 dB nominal, RIAA equalized MC: 56dB nominal, RIAA equalized
USB Function A/D, - 16 bit 44.1 kHz or 48 kHz USB selectable; Computer interface - USB 2.0 compliant Windows 7 or above, MAC OS X or above
Power Supply Requirements 100-240V AC, 50/60 Hz
Power Consumption 3 W
Dimensions 450.0 mm (17.72") W x 352.0 mm (13.86")D x 157.0 mm (6.18")H
Weight 7.3 kg (16.1 lbs.)
Accessories Included AT-VM95E Dual Moving Magnet stereo cartridge (black) with replaceable stylus; AT-HS6 lightweight headshell; AC adapter ; dual RCA (male) to dual RCA (male) stereo cable; 45 RPM adapter; USB cable; dust cover with hinges.

Manual: https://eu.audio-technica.com/resources/AT-LP5X_UM_162501850_V1_EN_web_190927.pdf

Fully Automatic Wireless Belt-Drive Turntable

The AT-LP70XBT Automatic Wireless Turntable is the perfect beginner turntable for those beginning their audiophile journey. Combining the experience of warm, analog audio with the convenience of Bluetooth® technology, you can listen to your vinyl over Bluetooth-enabled speakers, headphones, or other devices, including those that support the high-quality Qualcomm® aptX™ Adaptive audio codec. This user-friendly turntable plays both 33-1/3 and 45 RPM records and, in addition to its Bluetooth wireless technology, has a built-in switchable phono preamp that allows the turntable to connect to a home stereo, powered speakers, or another component, with or without a dedicated phono input.

At the heart of the AT-LP70XBT is a top-notch phono cartridge for unmatched, high-fidelity audio. Built with Audio-Technica’s industry-leading phono cartridge expertise, the AT-VM95C is a versatile, superior-performance cartridge that other turntables in this class simply can’t match. Integrated into the J-shaped tonearm, the AT-VM95C cartridge with a 0.6 mil conical stylus offers excellent channel separation and low distortion for outstanding tonal quality. To further personalise vinyl listening, the stylus can also be easily upgraded with any other styli (elliptical, micro linear, or Shibata) in our VM95 Series, offering unprecedented customisation for a turntable in this category.

To ensure peak sound performance, the AT-LP70XBT includes a three-piece, anti-resonance chassis that provides a solid foundation to dampen unwanted noise for improved sound quality. The included AC adapter further reduces noise as the AC/DC conversion is moved to the outside of the chassis to limit any unfavorable noise.

Easy to Use
Equipped with Bluetooth wireless technology for simple connection to powered speakers and headphones, the AT-LP70XBT plays 33⅓ and 45 RPM records automatically at the press of a button. And since the J-shaped tonearm features an integrated AT-VM95C cartridge there’s no installation, balancing or other tonearm setup required.

Refine Your Sound
The turntable’s unique AT-VM95C Integral Dual Moving Magnet™ phono cartridge is compatible with any VM95 Series replacement stylus (see list below on page), making it easy not only to replace the stylus when needed but also upgrade to a higher-quality stylus to enjoy more refined sound.

Replaceable / Upgradable AT-VM95 Series Styli
The turntable’s unique AT-VM95C Integral Dual Moving Magnet™ phono cartridge is compatible with any AT-VM95 Series replacement stylus, making it easy not only to replace the stylus when needed but also upgrade to a higher-quality stylus to enjoy more refined sound.

Features:
• Fully automatic belt-drive turntable operation with two speeds: 33-1/3, 45 RPM
• High-fidelity audio with Bluetooth wireless technology
• Connects wirelessly to speakers and other devices equipped with Bluetooth wireless technology or to wired audio systems and powered speakers via included dual RCA output cable
• Compatible with the high-quality Qualcomm® aptX™ Adaptive audio codec
• A fixed-body AT-VM95C Integral Dual Moving Magnet™ phono cartridge is compatible with any VM95 Series replacement stylus, offering a wide choice of options for every budget and application
• Stylish three-piece chassis construction dampens resonance for improved sound quality*
• J-shaped tonearm is engineered to minimize tracking errors
• Tonearm lock reduces risk of stylus damage
• Built-in switchable phono/line pre-amplifier
• Anti-resonance, die-cast aluminium platter with felt mat
• AC adapter handles AC/DC conversion outside of the chassis, reducing noise in the signal chain
• Includes detachable RCA output cable (dual RCA male to dual RCA male with ground), 45 RPM adapter, and removable hinged dust cover
*Compared to AT-LP60X.

Specifications:
Turntable
• Motor DC motor
• Drive Method Belt-drive
• Speeds 33-1/3 RPM, 45 RPM
• Turntable Platter Die-cast aluminium
• Wow and Flutter < 0.25% (WTD)
• Signal-to-Noise Ratio > 55 dB
• Cartridge Type This product is equipped with an AT-VM95C Dual Moving Magnet Stereo Cartridge. The cartridge cannot be removed.
• Output Level PHONO: 4.0 mV nominal at 1 kHz, 5 cm/sec
• LINE: 252 mV nominal at 1 kHz, 5 cm/sec
• Phono Pre-Amp Gain 36 dB nominal, RIAA equalized
• Power Consumption 1.6 W
• Dimensions 400 mm (16") × 330 mm (13") × 110 mm (4.3") (W × D × H)
• Weight Approx. 2.9 kg (6.4 lbs)
• AC Adapter *Type: FJ-SW1261200500DN / Rated Input Voltage: 100 to 240 V AC / Rated Input Current: 0.4 A max. / Rated Frequency: 50 Hz / 60 Hz / Rated Output Voltage: 12 V DC / Rated Secondary Current: 0.5 A / Cable Length: Approx. 1.5m (4.9')
• Effective Arm Length 220 mm (8.7")
• Overhang 18 mm (0.71")
• Tracking Error Angle Less than 2.0°
• Replacement Stylus AT-VMN95C (sold separately)
• Replacement Belt AT-LP70X exclusive belt (sold separately)
• Communication System Bluetooth version 5.2
• Frequency Band 2.402 GHz to 2.480 GHz
• Maximum RF Output 2.5 mW EIRP
• Maximum Communication Range Line of sight - approx. 10 m (33')
• Modulation Method GFSK, Pi/4DQPSK, 8DPSK
• Compatible Bluetooth Profile A2DP
• Support Codec Qualcomm® aptX™ Adaptive audio, Qualcomm® aptX™ audio, SBC

Accessories Included
• Dust cover
• Felt mat
• Platter (with drive belt)
• Dust cover hinges
• 45 RPM adapter
• RCA audio cable (Approx. 1.0 m (3.3'))
• AC adapter (Approx. 1.5 m (4.9'))

Notes *The included AC adapter may differ depending on the country of sale. Check the rating label on the AC adapter. For details, contact your local Audio-Technica dealer.

Fully Automatic Wireless Belt-Drive Turntable

The AT-LP70XBT Automatic Wireless Turntable is the perfect beginner turntable for those beginning their audiophile journey. Combining the experience of warm, analog audio with the convenience of Bluetooth® technology, you can listen to your vinyl over Bluetooth-enabled speakers, headphones, or other devices, including those that support the high-quality Qualcomm® aptX™ Adaptive audio codec. This user-friendly turntable plays both 33-1/3 and 45 RPM records and, in addition to its Bluetooth wireless technology, has a built-in switchable phono preamp that allows the turntable to connect to a home stereo, powered speakers, or another component, with or without a dedicated phono input.

At the heart of the AT-LP70XBT is a top-notch phono cartridge for unmatched, high-fidelity audio. Built with Audio-Technica’s industry-leading phono cartridge expertise, the AT-VM95C is a versatile, superior-performance cartridge that other turntables in this class simply can’t match. Integrated into the J-shaped tonearm, the AT-VM95C cartridge with a 0.6 mil conical stylus offers excellent channel separation and low distortion for outstanding tonal quality. To further personalise vinyl listening, the stylus can also be easily upgraded with any other styli (elliptical, micro linear, or Shibata) in our VM95 Series, offering unprecedented customisation for a turntable in this category.

To ensure peak sound performance, the AT-LP70XBT includes a three-piece, anti-resonance chassis that provides a solid foundation to dampen unwanted noise for improved sound quality. The included AC adapter further reduces noise as the AC/DC conversion is moved to the outside of the chassis to limit any unfavorable noise.

Easy to Use
Equipped with Bluetooth wireless technology for simple connection to powered speakers and headphones, the AT-LP70XBT plays 33⅓ and 45 RPM records automatically at the press of a button. And since the J-shaped tonearm features an integrated AT-VM95C cartridge there’s no installation, balancing or other tonearm setup required.

Refine Your Sound
The turntable’s unique AT-VM95C Integral Dual Moving Magnet™ phono cartridge is compatible with any VM95 Series replacement stylus (see list below on page), making it easy not only to replace the stylus when needed but also upgrade to a higher-quality stylus to enjoy more refined sound.

Replaceable / Upgradable AT-VM95 Series Styli
The turntable’s unique AT-VM95C Integral Dual Moving Magnet™ phono cartridge is compatible with any AT-VM95 Series replacement stylus, making it easy not only to replace the stylus when needed but also upgrade to a higher-quality stylus to enjoy more refined sound.

Features:
• Fully automatic belt-drive turntable operation with two speeds: 33-1/3, 45 RPM
• High-fidelity audio with Bluetooth wireless technology
• Connects wirelessly to speakers and other devices equipped with Bluetooth wireless technology or to wired audio systems and powered speakers via included dual RCA output cable
• Compatible with the high-quality Qualcomm® aptX™ Adaptive audio codec
• A fixed-body AT-VM95C Integral Dual Moving Magnet™ phono cartridge is compatible with any VM95 Series replacement stylus, offering a wide choice of options for every budget and application
• Stylish three-piece chassis construction dampens resonance for improved sound quality*
• J-shaped tonearm is engineered to minimize tracking errors
• Tonearm lock reduces risk of stylus damage
• Built-in switchable phono/line pre-amplifier
• Anti-resonance, die-cast aluminium platter with felt mat
• AC adapter handles AC/DC conversion outside of the chassis, reducing noise in the signal chain
• Includes detachable RCA output cable (dual RCA male to dual RCA male with ground), 45 RPM adapter, and removable hinged dust cover
*Compared to AT-LP60X.

Specifications:
Turntable
• Motor DC motor
• Drive Method Belt-drive
• Speeds 33-1/3 RPM, 45 RPM
• Turntable Platter Die-cast aluminium
• Wow and Flutter < 0.25% (WTD)
• Signal-to-Noise Ratio > 55 dB
• Cartridge Type This product is equipped with an AT-VM95C Dual Moving Magnet Stereo Cartridge. The cartridge cannot be removed.
• Output Level PHONO: 4.0 mV nominal at 1 kHz, 5 cm/sec
• LINE: 252 mV nominal at 1 kHz, 5 cm/sec
• Phono Pre-Amp Gain 36 dB nominal, RIAA equalized
• Power Consumption 1.6 W
• Dimensions 400 mm (16") × 330 mm (13") × 110 mm (4.3") (W × D × H)
• Weight Approx. 2.9 kg (6.4 lbs)
• AC Adapter *Type: FJ-SW1261200500DN / Rated Input Voltage: 100 to 240 V AC / Rated Input Current: 0.4 A max. / Rated Frequency: 50 Hz / 60 Hz / Rated Output Voltage: 12 V DC / Rated Secondary Current: 0.5 A / Cable Length: Approx. 1.5m (4.9')
• Effective Arm Length 220 mm (8.7")
• Overhang 18 mm (0.71")
• Tracking Error Angle Less than 2.0°
• Replacement Stylus AT-VMN95C (sold separately)
• Replacement Belt AT-LP70X exclusive belt (sold separately)
• Communication System Bluetooth version 5.2
• Frequency Band 2.402 GHz to 2.480 GHz
• Maximum RF Output 2.5 mW EIRP
• Maximum Communication Range Line of sight - approx. 10 m (33')
• Modulation Method GFSK, Pi/4DQPSK, 8DPSK
• Compatible Bluetooth Profile A2DP
• Support Codec Qualcomm® aptX™ Adaptive audio, Qualcomm® aptX™ audio, SBC

Accessories Included
• Dust cover
• Felt mat
• Platter (with drive belt)
• Dust cover hinges
• 45 RPM adapter
• RCA audio cable (Approx. 1.0 m (3.3'))
• AC adapter (Approx. 1.5 m (4.9'))

Notes *The included AC adapter may differ depending on the country of sale. Check the rating label on the AC adapter. For details, contact your local Audio-Technica dealer.

AT-LPW30TK
Manual Belt-Drive Wood Base Turntable

• Teak effect wood veneer finish
• Connect directly to speakers at home with the built-in phono preamplifier
• Fully manual, belt-drive operation with two speeds: 33-1/3 and 45 RPM
• Adjustable dynamic anti-skate control
• Professional anti-resonance, die-cast aluminium platter with rubber mat
• AT-HS4 headshell and AT-VM95C Dual Moving Magnet phono cartridge

Video: https://www.youtube.com/watch?v=gmWsctJ8Kzk

Manual Belt-Drive Turntable (Wireless & Analogue)

Audio-Technica’s AT-LPW50BT-RW wireless turntable provides optimal high-fidelity audio reproduction with the option of wired or Bluetooth® listening. The manual record player’s stunning rosewood-finished veneer adds to the turntable’s refined style, and also dampens low-frequency acoustic feedback to ensure you experience crystal clear, uninterrupted sound.

Incorporating a top-quality tonearm and the critically-acclaimed AT-VM95E, Audio-Technica’s AT-LPW50XBT-RW record player with Bluetooth® comes complete with everything a vinyl enthusiast needs to enjoy an immersive, rich analog audio experience.

The LPW50BT-RW takes Audio-Technica’s range of wooden turntables to the next level, incorporating a variety of enhanced features and wireless connectivity. This Bluetooth® vinyl player is the culmination of Audio-Technica’s 60 years of dedication to analog listening, creating a record player that produces unrivalled sound quality while featuring innovative audio technology.

Integrated Bluetooth® technology gives listeners the unique option to operate the AT-LPW50XBT-RW belt-drive turntable wirelessly. Whether you prefer wired listening to enjoy the distinct warmth of analog audio with no compromise on sound quality, or want to try out pairing your turntable with your brand new wireless headphones or speakers, you can do it all with this versatile record player.

Wired or Wireless Listening
Pair seamlessly to the latest wireless earbuds, headphones and speakers or use the included stereo RCA output cable for a traditional wired connection and optimal sound reproduction.

Plug-In and Play
AT-LPW50BTRW is equipped with a built-in selectable pre-amplifier for phono or line-level output, so you can choose whether to use the turntable’s built-in preamp and plug your vinyl player straight into a device with line-level input, or expand your setup with an external preamplifier.

Fully Manual Operation
Audio-Technica’s LPW50BTRW features manual, belt-drive operation with two speeds - 33-1/3 and 45 RPM - so you can make your way through your full vinyl collection. The sensor-monitored motor maintains accurate platter rotation speed and an adjustable dynamic anti-skate control minimizes distortion.

Refine Your Sound
The turntable includes a straight carbon-fibre tonearm with adjustable tracking force, hydraulically damped lift control and lockable rest, plus a matching matte-silver AT-HS4 universal ½"-mount headshell. The LPW50BTRW also includes one of Audio-Technica’s most versatile cartridges, the high-performance AT-VM95E. The dual moving magnet phono cartridge is compatible with any VM95 series replacement stylus, offering a wide choice of options for every budget and application.

Audio Aesthetics
The 30mm thick MDF plinth, with rosewood veneer dampens low-frequency acoustic feedback and minimises distortion while the professional anti-resonance, die-cast aluminium platter with rubber mat also works to ensure you enjoy superb audio clarity with minimal disturbance.

Features:
• Fully manual, belt-drive operation with two speeds: 33-1/3 and 45 RPM
• Motor features a speed-sensor system to maintain accurate platter rotation speed
• Adjustable dynamic anti-skate control
• Professional anti-resonance, die-cast aluminum platter with rubber mat
• AT-HS4(silver) universal 1/2"-mount headshell and AT-VM95E (black) Dual Moving Magnet phono cartridge with 0.3 x 0.7 mil elliptical stylus
• The AT-VM95Ecartridge is compatible with any VM95 Series replacement stylus, offering a wide choice of options for every budget and application
• Straight carbon-fiber tonearm with hydraulically damped lift control and lockable rest
• Anti-resonance 30 mm thick MDF (medium density fiberboard) plinth with rosewood-finished wood veneer
• Built-in switchable phono pre-amplifier for phono or line-level output
• AC adapter handles AC/DC conversion outside of the chassis, reducing noise in the signal chain
• Includes dual RCA (male) to dual RCA (male) stereo cable, 45 RPM adapter, rubber mat, and removable hinged dust cover

Specifications:
Turntable
• Type Belt-drive manual turntable
• Motor DC servo with Active Speed Stabilization
• Drive Method Belt drive
• Speeds 33-1/3 RPM, 45 RPM
• Turntable Platter Die-cast aluminum
• Wow and Flutter < 0.15 % WRMS (33 RPM) at 3 kHz
• Signal-to-Noise Ratio > 60 dB
• Output Level PHONO: 4.0 mV nominal at 1 kHz, 5 cm/sec LINE: 200 mV nominal at 1 kHz, 5 cm/sec
• Phono Pre-Amp Gain 35 dB nominal, RIAA equalized
• Power Supply Requirements 100 to 240 V, 50/60 Hz, 0.5 A Max
• Power Consumption 1.8 W
• Dimensions 420 mm (16.54") x 340 mm (13.39") x 126 mm (4.96") (W x D x H)
• Weight 5.5 kg (12 Ibs)
• Accessories Included: • Dust cover • Rubber mat • Platter (with drive belt) • Dust cover hinges • Counterweight • Headshell (AT-HS4 SV) with VM stereo cartridge (AT-VM95EBK) • 45-RPM adapter • RCA audio cable (Approx. 1.0m (3.3')) • AC adapter (Approx. 1.5m (4.9'))
• AC Adapter 12 V, 1.0 A
• Tonearm Type Static balanced straight carbon tonearm
• Effective Arm Length 223.6 mm
• Overhang 18.6 mm
• Tracking Error Angle Less than 2.0°
• Stylus Pressure Adjustment Range 0 to 3.0 g
• Applicable Cartridge Weight (including headshell) 11.5 to 16.5 g
• Replacement Stylus AT-VMN95EBK (sold separately)
• Replacement Headshell AT-HS4 SV (sold separately)
• Replacement Belt AT-LPW50BT exclusive belt (sold separately)
• Communication System Bluetooth version 5.2
• Frequency Band 2.402 GHz to 2.480 GHz
• Maximum RF Output 15 mW EIRP
• Maximum Communication Range Line of sight - approx. 10 m (33')
• Modulation Method GFSK, Pi/4DQPSK, 8DPSK
• Compatible Bluetooth Profile A2DP
• Support Codec SBC

Fully Manual Belt-Drive Turntable
•Fully manual, belt-drive operation with two speeds: 33-1/3 and 45 RPM
•Motor with speed-sensor system to maintain accurate platter rotation speed
•Adjustable dynamic anti-skate control
•High-isolation, height-adjustable feet
•Professional anti-resonance, die-cast aluminum platter with rubber mat
•AT-HS4 ½"-mount headshell and AT-VM95E Dual Moving Magnet phono cartridge

The AT-LPW50PB is a fully manual, belt-drive turntable designed to give you optimal high-fidelity audio reproduction from vinyl. It features an anti-resonance 30 mm thick MDF (medium density fiberboard) plinth, with a high-gloss, piano-black finish, to dampen low-frequency acoustical feedback, and a sensor-monitored motor to ensure accurate platter rotation speeds of 33-1/3 and 45 RPM.

The turntable includes a straight, matte-finish, carbon-fibre tonearm with adjustable tracking force and an AT-HS4 universal ½"-mount headshell with a black AT-VM95E Dual Moving Magnet phono cartridge. Audio-Technica has been a leader in phono cartridge design for more than 50 years, and that expertise shows in the versatile, high-performance AT-VM95E cartridge, which comes with a 0.3 x 0.7 mil elliptical stylus, but is also compatible with any VM95 Series replacement stylus, offering a wide choice of options for every budget and application.

The AT-LPW50PB is equipped with a built-in selectable phono preamp and a detachable dual RCA output cable to enable direct connection to components with or without a dedicated phono input.

Fully manual, belt-drive operation with two speeds: 33-1/3 and 45 RPM
•Adjustable dynamic anti-skate control
•AT-HS4 universal ½"-mount headshell and AT-VM95E Dual Moving Magnet phono cartridge (black) with 0.3 x 0.7 mil elliptical stylus
•Straight, matte-finish, carbon-fibre tonearm with hydraulically damped lift control and lockable rest
•High-isolation, height-adjustable feet
•AC adapter handles AC/DC conversion outside of the chassis, reducing noise in the signal chain

Drive Method: Belt-Drive
Type: 2-speed, fully manual operation
Motor: DC servo with Active Speed Stabilization
Speeds: 33-1/3 RPM, 45 RPM
Turntable Platter: Die-cast aluminum
Signal-to-Noise Ratio: > 60 dB
Output Level: Pre-amp: "PHONO": 4.0 mV nominal at 1 kHz, 5 cm/sec Pre-amp "LINE": 200 mV nominal at 1 kHz, 5 cm/sec
Power Supply Requirements: 100 to 240 V, 50/60 Hz
Power Consumption: 220 V 50 Hz
Working: 1.3 W
Motor off: 1.1 W
Power off: 0.1 W
Dimensions: With dust cover 126.0 x 420.0 x 340.0 (H x W x D mm) Without dustcover and hinges:114.0 x 420.0 x 340.0 (H x W x D mm)
Weight: 4.81 kg (without dustcover)
Accessories Included:
• AT-HS4BK Headshell,
• AT-VM95E Dual Moving Magnet Cartridge with elliptical Stylus in black
• Detachable RCA output cable (dual RCA male to dual RCA male)
• Platter
• AC adapter
• 45 RPM adapter
• Counterweight
• Turntable mat
• Removable hinged dust cover

Manual: https://www.audio-technica.com/cms/resource_library/literature/e89c31b269914a97/at_lpw50pb_um_162502020_v1_en_web_191220.pdf

Machined aluminium housing turntable leveler that provides a precise level for horizontal adjustment of the turntable.

AT618a
Disc Stabiliser

• Holds record firmly in place stabilising the record
• Thick rubber construction
• 600g

Direct Drive Turntable with Bluetooth® aptX HD

• Bluetooth aptX HD – Switchable Hi-Res wireless streaming. Place the turntable on a flat-surface that suits you.
• Built-In Phono Stage – Switchable phono pre-amp, direct connection to amp – keep your setup simple.
• Direct Drive – Consistent drive speed with pitch-perfect audio reproduction.
• Pre-installed High-Output MC Cartridge – Pristine musical detail, custom design. Easy setup.
• New Tonearm with Removable Headshell – Lightweight and strong. Tracks your records flawlessly.

Just Add Vinyl
You’ve spent years curating the perfect record collection, searching for hidden gems in record shops and online – because you love music. Our shared love means that we didn’t stop with Alva TT.
We pushed on to create Alva TT V2; with a direct drive system, bespoke MC cartridge, an all-new tone-arm, and Hi-Res Bluetooth with an integrated phono stage – both now switchable.
We believe that your records deserve to sound as fantastic as they look.

King of Convenience
Alva TT V2 is for people who want to listen to records at exceptional quality – without the need to choose or fit extra components. TT V2 comes with a bespoke designed cartridge pre-installed. It connects to pretty much any audio system too, thanks to a switchable integrated phono-stage. It even works wirelessly with high quality Bluetooth speaker systems.

Hi-Res Bluetooth
Built-in Bluetooth aptX HD liberates Alva from the rest of your hi-fi. With the freedom to place an Alva deck on any flat surface, your records take centre-stage. Music can be streamed to any compatible Bluetooth kit, including headphones, at up to 24bit/48kHz Hi-Res quality. Or, you can deactivate it and simply use phono cables – it’s your call.

Integrated Phono Stage
Alva TT V2 has an integrated phono stage (phono pre-amp), derived from our award-winning Alva Duo – to reveal incredible detail from your records. It means you can connect TT V2 to any amp or compatible speaker system. You can deactivate the deck’s phono stage, too – ideal if your amp already has one or to keep upgrade options open.

MC Cartridge Pre-installed
Alva TT V2’s bespoke cartridge is ready fitted – so there’s no tricky set-up, and its sound is perfectly matched to the other components in the turntable. We designed the high-output Moving Coil (MC) cartridge with an exposed cantilever. It reduces unwanted resonance and vibration, delivers high levels of gain and outstanding musical detail during playback.

Direct Drive
Alva TT V2 has a medium-torque Direct Drive motor, like its predecessor the TT. The 8 pole, 3 phase, brushless DC motor is quartz controlled to ensure accurate turntable speed. With precision control, and silent running, Alva TT V2 achieves just 0.06% wow and flutter. This means excellent pitch stability – particularly during longer, more sustained, musical notes.

Reassuringly Solid Platter
Complimenting the direct drive motor, Alva TT V2’s platter has the feel of finely polished stone. It’s made from Polyoxymethylene, a semi-crystalline thermoplastic used in precision engineering applications, where high stiffness and dimensional stability are demanded. The weight of the platter, coupled with our medium torque direct drive motor, ensures excellent speed stability during playback of records.

All-New Tonearm
After hours of testing, our engineers selected a new high-mass, low-resonance tonearm for Alva TT V2 and Alva ST. By minimising resonant frequencies, and in combination with the cartridge, it helps retrieve the maximum detail from your records. A detachable die-cast aluminium headshell makes swapping cartridges easy – then fine-tuned with greater precision thanks to a new anti-skating dial.

Designed for Life
A record collection can last a lifetime, so why shouldn’t a turntable? We built Alva TT V2 to endure, starting with a top plate hewn from 6mm aluminium plate, and layer of EVA to absorb vibration sitting on MDF. It’s cradled in a composite chassis and weighs an impressive 10.9kg. Reassuring solid construction, with great acoustic qualities too.

Timeless Style, from London
Finished with a lunar-grey aluminium top plate and matt black plinth, tapering to our trademark floating wedge base, Alva TT V2 celebrates our timeless house-style. It’s the perfect match for our best-selling CX Series hi-fi separates and shares the laser-etched brand logo with our premium Edge Series.

Dust Never Sleeps
Keep your new Alva turntable’s finely balanced tonearm and aluminium top-plate pristine when you’ve finished spinning discs for the day, with the hinged dust-cover. It’s easy to raise, lower, remove and re-attach – the choice is yours.

Technical specifications:
• TYPE: Direct Drive
• TURNTABLE SPEEDS: 33.3, 45rpm
• WOW & FLUTTER: <0.1%
• TURNTABLE PLATTER: POM (Polyoxymethylene)
• PLATTER DIAMETER: 305mm
• PLATTER WEIGHT: 2.2kg
• AUDIO OUT: RCA Phono/Line Level (Switchable)
• BLUETOOTH: SBC/aptX/aptX HD
• POWER SUPPLY: AC 100-240V, 60/50Hz
• POWER CONSUMPTION: 5.5W
• MAX POWER CONSUMPTION: 20W
• STANDBY POWER CONSUMPTION: <0.25W
• DIMENSIONS (W X H X D): 435 x 139 x 368mm
• WEIGHT: 10.9kg
• PHONO STAGE GAIN @1KHZ: 42dB
• PHONO STAGE NOMINAL OUTPUT: 250Vrms
• PHONO STAGE INPUT NOISE (A-WEIGHTED): 0.1u Vrms
• PHONO STAGE RIAA CURVE ACCURACY: *+/- 0.3dB 30Hz-20kHz
• PHONO STAGE SIGNAL/NOISE RATIO: >90dB
• PHONO STAGE THD+N 1KHZ: 0.0025%
• PHONO STAGE INPUT IMPEDANCE: 47Ω
• PHONO STAGE INPUT CAPACITANCE: 100pF
• TONEARM TYPE: Static Balanced Tonearm w/ detachable Headshell
• TONEARM EFFECTIVE LENGTH: 221.5mm
• TONEARM OVERHANG: 19mm
• TONEARM EFFECTIVE MASS: 19.6g
• TONEARM COMPATIBLE CARTRIDGE WEIGHTS: 4.5-12g
• CARTRIDGE: High Output Moving Coil
• CARTRIDGE FREQUENCY RESPONSE: *+/- 1dB 30Hz-20kHz
• CARTRIDGE STYLUS: Elliptical
• CARTRIDGE CANTILEVER: Aluminium
• CARTRIDGE OUTPUT LEVEL: 2mV @1kHz
• CARTRIDGE TRACKING FORCE: 2g
• CARTRIDGE RECOMMENDED LOAD: 47Ω

Manual: https://manuals.cambridgeaudio.com/en/alva-tt-v2

Integrated Stereo Amplifier with (Built-in) Phono-Stage

• 35 Watts Power per Channel – for detailed performance at all volumes, ideal for smaller/medium sized rooms
• Built-In Phono Stage – to plug & play a vinyl turntable
• Slim Timeless Design – classic hi-fi size, with Lunar Grey aluminium trim
• Tone Controls – fine-tune sound to compensate for room dynamics
• Digital Display – white LED, clearly shows; source, volume & menus
• Headphone Socket – full size socket for high-quality after-hours listening
• Front Aux Input – 3.5mm socket to easily connect compatible devices

Sound Comes First
Our AXA35 integrated amp offers 35 watts per channel and has a built-in moving magnet phono stage – perfect for vinyl enthusiasts. A white LED dot matrix display confirms listening source, and separate tone controls mean you can adjust the sound to suit your taste. There’s a large ¼” (6.35mm) headphone socket too, ideal for high-quality listening without disturbing those who might not share your great taste in music.

Your Journey into Sound
AXA35 is the ideal amp to begin listening to music and really appreciating it – hearing detail in familiar tunes you’ve previously missed. That’s down to the toroidal transformer it uses, a tech found higher up our range. Choose a pair of speakers to suit your taste, perhaps they’ve been in the family for years or maybe something from our SX Series.

Release the Wheels of Steel
The built-in phono stage is the ace up AXA35’s sleeve. It means that you can plug a turntable straight in without any extra kit. Moving magnet (MM) compatibility means AXA35 works with a wide variety of turntables – including that vintage one you’ve had your eye on. Soon you’ll be playing the records you’ve been saving for, and planning what to buy next.

Setting the Tone
With separate bass and treble controls, you can fine-tune AXA35’s sound to suit your taste, speakers and room dynamics. The volume level is shown on the LED dot matrix display, and with 35 watts per channel you’ll have plenty of kick for smaller to medium sized rooms.

Wired for Sound
AXA35 is a well-connected amp, with no less than 4 pairs of RCA inputs, plus a pair of phono sockets for a turntable and a pair of recording outputs. There’s a rear USB socket for technical upgrades. Hi-fi quality speaker binding posts (connectors), compatible for banana plugs, mean that thick cable connects securely for an authentic sound.

Designed for Life
As with the rest of AX Series, AXA35 shares our house-style of Lunar Grey minimalist fascia, black steel cabinet and ‘floating’ base. This timeless look enables an upgrade path through our range. A slim build, in the classic 430mm hi-fi width, also means that AXA35 can easily slot, and breathe new life, into a much-loved system.

Technical specifications:
• POWER OUTPUT: 35 Watts (into 8 Ohms)
• THD (UNWEIGHTED): <0.01% @ 1kHz, 80% of rated power <0.15% 20Hz - 20kHz, 80% of rated power
• FREQUENCY RESPONSE (-3DB): 5Hz - 50kHz
• S/N RATIO (REF 1W): >82dB (unweighted)
• INPUT IMPEDANCES: 47k ohms
• POWER AMP DAMPING FACTOR: > 50
• MAX. POWER CONSUMPTION: 260W
• BASS/TREBLE CONTROLS: Shelving, ultimate boost/cut +/- 10dB @ 100Hz and 10kHz
• STANDBY POWER CONSUMPTION: <0.5W
• INPUTS: 4x RCA, 1x Phono, 1 x 3.5mm Aux input (front panel)
• OUTPUTS: Speakers, Rec Out, USB 5V power
• DIMENSIONS (HXWXD): 83 x 430 x 335mm (3.3 x 16.9 x 13.2”)
• WEIGHT: 5.6kg (12.3lbs)
• IN THE BOX: AXA35 Integrated Amplifier, Power Cable, Remote Control, 2 x AAA Batteries

Moving Coil & Moving Magnet Phono Preamp

Squeeze every inch of detail from your record collection with our highest quality moving magnet and moving coil phono stage, with integrated headphone amp; the Duo Phono Preamplifier.

Vinyl as it's Supposed to Sound
Whether you’re dusting off your record collection or embracing analogue through the vinyl revival, there’s a unique experience to be had from the moment you drop the needle on your favourite album. To preserve the unique warmth of the vinyl sound, the Duo phono preamplifier has been carefully designed with a state-of-the-art switch mode power supply and a new surface mounted circuit board layout to reduce unwanted noise.

Why Choose a Dedicated Phono Preamplifier?
Due to the low-level signals created by a turntable, not all hi-fi amplifiers will let you connect directly to a record player. The phono preamplifier boosts this signal to something a power amplifier can work with. The challenge at this stage though is that noise can easily be added.
This is why we’ve designed the Duo around exceptional components that deliver the warm and detailed sound that’s synonymous with vinyl, all without distorting the signal from your moving magnet cartridge turntable. The switch mode power supply improves performance by switching outside of audible frequency to drastically reduce hum and new circuit board layout uses surface-mount components to reduce noise.

Vinyl. Just for You
Enjoy the warmth of vinyl privately thanks to Duo’s integrated headphone output. Uniquely, we integrated a 6.35mm headphone jack directly into the phono stage, so you can still enjoy your records when there’s no option to play out loud.
The integrated headphone output also means no need to turn on your amplifier just to power your headphones, resulting in a more eco-friendly listening experience.

Attention to Detail
If some records in your collection are a little worse for wear, the subsonic filter will help to eliminate low frequency rumbles that can be caused by imperfections within your vinyl. Combine this with the balance control for handling potential cartridge imbalances in your record player (that can cause a difference between the left and right channels) and the result is a detailed experience with accurate soundstage.

Eco Friendly
The Duo phono preamplifier is green at heart with less than half a watt standby power consumption and auto power down feature if the unit isn’t used after a 20 minute period. This in turn gives the unit the same worldwide voltage for compatibility wherever you are in the world.

Technical specifications:
• MAX POWER CONSUMPTION: 10W
• CARTRIDGE SUPPORT: Moving Magnet | Moving Coil
• GAIN @ 1KHZ: MM: 39dB | MC: 60dB
• NOMINAL OUTPUT: 300mV
• SENSITIVITY FOR NOMINAL OUTPUT: MM: 3.35mV | MC: 305uV
• EQUIVALENT INPUT NOISE (A-WEIGHTED): MM: ~0.09uV | MC: ~0.08uV
• RIAA CURVE ACCURACY: +/- 0.3dB 30Hz-50Hz
• SIGNAL TO NOISE RATIO GROUNDED INPUTS REF. 1V OUTPUT (20HZ-20KHZ BW): MM: >90dB | MC: >70dB
• THD+N 1KHZ (20-20KHZ BW): MM: <0.0025% | MC: <0.20%
• INPUT IMPEDANCE: MM: 47k Ohms | MC: 100 Ohms
• INPUT CAPACITANCE: 100pF
• OVERLOAD MARGIN: >30dB
• CROSSTALK @ 10KHZ: MM: >85dB | MC: 75dB
• DIMENSIONS (H X W X D): 48 x 215 x 159 mm (1.9 x 8.5 x 6.2")
• WEIGHT: 0.95kg (2.1lbs)
• WHATS IN THE BOX?: Alva Duo Moving Coil & Moving Magnet Phono Preamp, User Manual, Safety Guide, Mains Lead

Moving Magnet Phono Preamplifier

Enjoy every last detail from your vinyl collection with our highest quality moving magnet phono stage, the Solo Phono Preamplifier.

Vinyl as it's Supposed to Sound
Whether you’re dusting off your record collection or embracing analogue through the vinyl revival, there’s a unique experience to be had from the moment you drop the needle on your favourite album. To preserve the unique warmth of the vinyl sound, the Solo phono preamplifier has been carefully designed with a state-of-the-art switch mode power supply and a new surface mounted circuit board layout to reduce unwanted noise.

Why Choose a Dedicated Phono Stage?
Due to the low-level signals created by a turntable, not all hi-fi amplifiers will let you connect directly to a record player. The phono preamplifier boosts this signal to something a power amplifier can work with. The challenge at this stage though is that noise can easily be added.
This is why we’ve designed the Solo around exceptional components that deliver the warm and detailed sound that’s synonymous with vinyl, all without distorting the signal from your moving magnet cartridge. The switch mode power supply improves performance by switching outside of audible frequency to drastically reduce hum and new circuit board layout uses surface-mount components to reduce noise.

Attention to Detail
If some records in your collection are a little worse for wear, the subsonic filter will help to eliminate low frequency rumbles that can be caused by imperfections within your vinyl. Combine this with the balance control for handling potential cartridge imbalances in your record player (that can cause a difference between the left and right channels) and the result is a detailed experience with accurate soundstage.

Eco Friendly
The Solo phono preamplifier is green at heart with less than half a watt standby power consumption and auto power down feature if the unit isn’t used after a 20 minute period. This in turn gives the unit the same worldwide voltage for compatibility wherever you are in the world.

Technical specifications:
• MAX POWER CONSUMPTION: 10W
• GAIN @ 1KHZ: 39dB
• NOMINAL OUTPUT: 300mV
• SENSITIVITY FOR NOMINAL OUTPUT: 3.35mV
• EQUIVALENT INPUT NOISE (A-WEIGHTED): ~0.09uV
• RIAA CURVE ACCURACY: +/- 0.65dB 30Hz-20kHz
• SIGNAL TO NOISE RATIO GROUNDED INPUTS REF. 1V OUTPUT (20HZ-20KHZ BW): >90dB
• THD+N 1KHZ (20-20KHZ BW): <0.0025%
• INPUT IMPEDANCE: 47k Ohm
• INPUT CAPACITANCE: 100pF
• OVERLOAD MARGIN: >30dB
• CROSSTALK @10KHZ: >85dB
• DIMENSIONS (H X W X D): 48x176x132 (1.9x6.9x5.2”)
• WEIGHT: 0.68kg/1.5lbs
• WHATS IN THE BOX: Alva Solo Moving Magnet Phono Preamplifier, User Manual, Safety Guide, Mains lead

The revolutionary concept combines the highest quality of music playback with a design that has won several awards worldwide – including the German Design Award and ‘Best Turntable’ award from ‘What Hi-Fi? Sound and Vision’ magazine. With the concept, to find an affordable entry point to the high-end world is a breeze. It reveals the magic of optimum sound reproduction even for those music lovers who could not previously afford this experience. You can buy the concept in a package with specially developed moving magnet (MM) or moving coil (MC) cartridges. A frictionless magnetic bearing tonearm is responsible for the optimal performance of the cartridges. All critical parameters from cartridge tracking weight to anti-skating are preadjusted in our factory. The concept represents the ideal of stress-free ‘plug and play’: unpack, connect, put the record on the platter – and just enjoy music. There was never more audiophile technology in this class of turntables.

The concept achieves these highest of requirements, realising the Clearaudio vision.

Beneath the sleek, contemporary exterior is a level of technical sophistication unique to Clearaudio.

The concept‘s body is carefully crafted from medium-density wood fibre (or, optionally, pressure-formed solid wood) with a selection of smart made-to-match surface finishes. The body’s upper layer incorporates a special high-tech satined plastic compound designed to minimise unwanted resonance.

The DC motor is fed by an external voltage-stabilised power supply and is completely decoupled from the chassis, isolating the record from any mechanical interference.

The concept tonearm features a magnetic bearing that is friction-free for extremely low distortion and superb performance. The package is completed with the high-quality Clearaudio CONCEPT MM or Clearaudio CONCEPT MC cartridge (toneam and/or cartridge upgrade possible).

With the concept turntable package, Clearaudio offers you an extremely innovative design that is very affordable.

Concept black/silver turntable including concept tonearm and concept MM cartridge.
Upgrade for cartridge/tonearm possible.
(Delivery without dustcover)

FEATURES
Technical Specifications:
• CONSTRUCTION DETAILS: Resonance-optimised turntable; chassis comprises medium-density wood fibre (silver / black) or pressure-formed solid wood (wood / dark wood); upper layer incorporates high-tech satined plastic compound.
• SPEED OPTIONS: 33 ⅓, 45, 78rpm
• DRIVE UNIT: Decoupled and resonance damped 12V DC motor, flat belt-drive and plug-in power supply unit designed for worldwide use with all networks and power frequencies.
• BEARING: Polished and tempered steel spindle in a sintered bronze housing, running on a teflon thrust-pad.
• PLATTER: 30mm / 1.18 inch main platter, made out of synthetic material with high-density and excellent dimension / precision CNC machined surface aluminium sub platter
• SPEED ACCURACY (MEASURED): ± 0.05%
• POWER CONSUMPTION: Max. consumption: 2.5 watts / Consumption in operation: 0.5 watts / Off mode: 0.0 watts
• TOTAL WEIGHT: Approx. 7.5kg (incl. tonearm and cartridge)
• DIMENSIONS (W/D/H): Approx. 16.54 × 13.78 × 4.92 inches (with tonearm) / Approx. 420 × 350 × 125mm (with tonearm)
• MANUFACTURER’S WARRANTY: 2 years*
* Provided the warranty card is fully completed and returned to Clearaudio within 2 weeks of purchase.

Manual: https://clearaudio.de/_assets/_pdf/manuals/turntables/CA_Concept_E+D.pdf?d=1667911999

The revolutionary concept combines the highest quality of music playback with a design that has won several awards worldwide – including the German Design Award and ‘Best Turntable’ award from ‘What Hi-Fi? Sound and Vision’ magazine. With the concept, to find an affordable entry point to the high-end world is a breeze. It reveals the magic of optimum sound reproduction even for those music lovers who could not previously afford this experience. You can buy the concept in a package with specially developed moving magnet (MM) or moving coil (MC) cartridges. A frictionless magnetic bearing tonearm is responsible for the optimal performance of the cartridges. All critical parameters from cartridge tracking weight to anti-skating are preadjusted in our factory. The concept represents the ideal of stress-free ‘plug and play’: unpack, connect, put the record on the platter – and just enjoy music. There was never more audiophile technology in this class of turntables.

The concept achieves these highest of requirements, realising the Clearaudio vision.

Beneath the sleek, contemporary exterior is a level of technical sophistication unique to Clearaudio.

The concept‘s body is carefully crafted from medium-density wood fibre (or, optionally, pressure-formed solid wood) with a selection of smart made-to-match surface finishes. The body’s upper layer incorporates a special high-tech satined plastic compound designed to minimise unwanted resonance.

The DC motor is fed by an external voltage-stabilised power supply and is completely decoupled from the chassis, isolating the record from any mechanical interference.

The concept tonearm features a magnetic bearing that is friction-free for extremely low distortion and superb performance. The package is completed with the high-quality Clearaudio CONCEPT MM or Clearaudio CONCEPT MC cartridge (toneam and/or cartridge upgrade possible).

With the concept turntable package, Clearaudio offers you an extremely innovative design that is very affordable.

Concept black turntable including concept tonearm and concept MM cartridge.
Upgrade for cartridge/tonearm possible.
(Delivery without dustcover)

FEATURES
Technical Specifications:
• CONSTRUCTION DETAILS: Resonance-optimised turntable; chassis comprises medium-density wood fibre (silver / black) or pressure-formed solid wood (wood / dark wood); upper layer incorporates high-tech satined plastic compound.
• SPEED OPTIONS: 33 ⅓, 45, 78rpm
• DRIVE UNIT: Decoupled and resonance damped 12V DC motor, flat belt-drive and plug-in power supply unit designed for worldwide use with all networks and power frequencies.
• BEARING: Polished and tempered steel spindle in a sintered bronze housing, running on a teflon thrust-pad.
• PLATTER: 30mm / 1.18 inch main platter, made out of synthetic material with high-density and excellent dimension / precision CNC machined surface aluminium sub platter
• SPEED ACCURACY (MEASURED): ± 0.05%
• POWER CONSUMPTION: Max. consumption: 2.5 watts / Consumption in operation: 0.5 watts / Off mode: 0.0 watts
• TOTAL WEIGHT: Approx. 7.5kg (incl. tonearm and cartridge)
• DIMENSIONS (W/D/H): Approx. 16.54 × 13.78 × 4.92 inches (with tonearm) / Approx. 420 × 350 × 125mm (with tonearm)
• MANUFACTURER’S WARRANTY: 2 years*
* Provided the warranty card is fully completed and returned to Clearaudio within 2 weeks of purchase.

Manual: https://clearaudio.de/_assets/_pdf/manuals/turntables/CA_Concept_E+D.pdf?d=1667911999

Flat belt
Drive belt for concept, concept active, Performance DC and Ovation.
Dimension: 160 × 4 × 0,8 mm

Level Gauge - Stainless steel
High precision gauge, calibrated.

An easy to use tool that quickly corrects undersized spindle holes – fitted with an ergonomic aluminum handle.
Diameter (Ø): 7.3 mm

Record weight made of aluminum with an integrated Teflon bushing on the underside for smooth placement (332 g).

This high-quality accessory, available in silver or black anodized aluminum, is specifically designed for the Performance series and stands out with its stylish design and exceptional functionality. Of course, this weight can also be used with other Clearaudio models and other brands.

The Performance record weight features an integrated Teflon bushing on the underside, ensuring smooth placement and significantly easing handling. At the same time, the weight is softly decoupled from the spindle. With a precisely calibrated weight of 332 grams, it is tailored for turntables with CMB bearings and clearaudio DC motors, making it the perfect complement to these systems.

Additionally, the record weight is compatible with all radial tonearms as well as the TT5 tonearm, making it a versatile accessory for audiophiles and professional users alike.

Weight: 332 g

Record weight made of aluminum with an integrated Teflon bushing on the underside for smooth placement (332 g).

This high-quality accessory, available in silver or black anodized aluminum, is specifically designed for the Performance series and stands out with its stylish design and exceptional functionality. Of course, this weight can also be used with other Clearaudio models and other brands.

The Performance record weight features an integrated Teflon bushing on the underside, ensuring smooth placement and significantly easing handling. At the same time, the weight is softly decoupled from the spindle. With a precisely calibrated weight of 332 grams, it is tailored for turntables with CMB bearings and clearaudio DC motors, making it the perfect complement to these systems.

Additionally, the record weight is compatible with all radial tonearms as well as the TT5 tonearm, making it a versatile accessory for audiophiles and professional users alike.

Weight: 332 g

Dustprotector for turntable
The Clearaudio Dustprotector is not only an eye-catcher on your turntable, it also prevents the accumulation of dust on the turntable, so you don't have to clean the platter before using it.

Stroboscope Testrecord for optimum control of the absolute speed

The tool to tune the optimal and exact speed of your turntable. The Stroboscopes break-in groove creates the additional stylus drag necessary to accurately measure the real-time speed of your turntable, and can also be used to break in new cartridges.
For the best possible accuracy, use in combination with our Speed Light.

Manual: https://clearaudio.de/_assets/_pdf/manuals/accessories/CA_Stroboscope%20Testrecord_E+D.pdf

Tonearm gauge
The easiest way to adjust the cartridge's Tracking Force.

Top quality made affordable
This is the best kid in class, the Crosley C62 is a unique straight-out-of-the-box turntable that's unmatched on the market. It comes with external speakers, aluminum platter, tone arm and adjustable counterweight, built-in Bluetooth receiver and a stylish Walnut finish. This turntable is the perfect way to step up your vinyl game without breaking the bank.
The C62 is designed by Crosley to give record collectors the opportunity to upgrade their record player system for an accessible price.
Created with an eye for interior design the (ready to go, straight out of the box) C62 record player and speakers have a veneer finish and a matt black aluminium tonearm with counter weight. The three anti vibration control feed and sturdy steel platter make the design complete. You can pump up the volume because of the two great quality speakers and NP5 diamond needle.

• 2-speed turntable (Speed 331/3, 45 RPM)
• Plays 7”, 10” or 12” records
• 2 External Full-range speakers: 8Ω 10W x 2 4” speakers
• NP5 Diamond needle
• Adjustable Tonearm Counterweight
• Aluminium Tonearm
• Low-Vibration Synchronous Motor
• Switchable Preamp
• Built-in amplifier
• Bluetooth input
• Belt-driven
• Anti-skate adjustment
• Special turntable feet for effective vibration control
• Dust cover
• Dimensions: 41.9 cm (l), 35.8 (w), 13.3 (h)
• Weight: 5.5 kg
• EU & UK AC Power adapter, DC output 15 V 2.4A
• Power Consumption 70W
• Speed Variance +1.5%
• Wow and Flutter < 0.15%
• Signal to Noise 72 dB
• Downforce Range 3.0-6.0g
• Effective Tonearm Length 8.6” (218.5mm)
• Overhang 0.73

Top quality made affordable
This is the best kid in class, the Crosley C62 is a unique straight-out-of-the-box turntable that's unmatched on the market. It comes with external speakers, aluminum platter, tone arm and adjustable counterweight, built-in Bluetooth receiver and a stylish Walnut finish. This turntable is the perfect way to step up your vinyl game without breaking the bank.
The C62 is designed by Crosley to give record collectors the opportunity to upgrade their record player system for an accessible price. Created with an eye for interior design this record player and speakers have a Walnut or Grey veneer finish and a matt black aluminium tonearm with counter weight. The three anti vibration control feed and sturdy steel platter make the upgrade complete.

• 2-speed turntable (Speed 331/3, 45 RPM)
• Plays 7”, 10” or 12” records
• 2 External Full-range speakers: 8Ω 10W x 2 4” speakers
• NP5 Diamond needle
• Adjustable Tonearm Counterweight
• Aluminium Tonearm
• Low-Vibration Synchronous Motor
• Switchable Preamp
• Built-in amplifier
• Bluetooth input
• Belt-driven
• Anti-skate adjustment
• Special turntable feet for effective vibration control
• Dust cover
• Dimensions: 41.9 cm (l), 35.8 (w), 13.3 (h)
• Weight: 5.5 kg
• EU & UK AC Power adapter, DC output 15 V 2.4A
• Power Consumption 70W
• Speed Variance +1.5%
• Wow and Flutter < 0.15%
• Signal to Noise 72 dB
• Downforce Range 3.0-6.0g
• Effective Tonearm Length 8.6” (218.5mm)
• Overhang 0.73

Now with 2-way Bluetooth!

A record player accessible to everyone. The Cruiser design is where it all started for Crosley and is still going strong.
This small suitcase has a playful appearance and because it’s so easy to use, everyone can (re)discover the magic
of vinyl. The Cruiser record player is now upgraded with 2-way Bluetooth, which makes it possible to connect an
external Bluetooth speaker for an amplified sound.

• 3-speed record player
• Plays 7”, 10” or 12” records
• 2 Built-in speakers | 3”, 4Ω, 3W
• NP6 needle
• Belt-driven
• Pitch control
• Bluetooth input & output
• Aux in
• Headphone Jack
• RCA output
• AC power adapter (EU & UK PLUG)
• 35.5 cm (l) 25.5 cm (w) 10 cm (h)
• Weight: 2.5 kg
• Autostop

Now with 2-way Bluetooth!

A record player accessible to everyone. The Cruiser design is where it all started for Crosley and is still going strong.
This small suitcase has a playful appearance and because it’s so easy to use, everyone can (re)discover the magic
of vinyl. The Cruiser record player is now upgraded with 2-way Bluetooth, which makes it possible to connect an
external Bluetooth speaker for an amplified sound.

• 3-speed record player
• Plays 7”, 10” or 12” records
• 2 Built-in speakers | 3”, 4Ω, 3W
• NP6 needle
• Belt-driven
• Pitch control
• Bluetooth input & output
• Aux in
• Headphone Jack
• RCA output
• AC power adapter (EU & UK PLUG)
• 35.5 cm (l) 25.5 cm (w) 10 cm (h)
• Weight: 2.5 kg
• Autostop

Now with 2-way Bluetooth!

A record player accessible to everyone. The Cruiser design is where it all started for Crosley and is still going strong.
This small suitcase has a playful appearance and because it’s so easy to use, everyone can (re)discover the magic
of vinyl. The Cruiser record player is now upgraded with 2-way Bluetooth, which makes it possible to connect an
external Bluetooth speaker for an amplified sound.

• 3-speed record player
• Plays 7”, 10” or 12” records
• 2 Built-in speakers | 3”, 4Ω, 3W
• NP6 needle
• Belt-driven
• Pitch control
• Bluetooth input & output
• Aux in
• Headphone Jack
• RCA output
• AC power adapter (EU & UK PLUG)
• 35.5 cm (l) 25.5 cm (w) 10 cm (h)
• Weight: 2.5 kg
• Autostop

Now with 2-way Bluetooth!

A record player accessible to everyone. The Cruiser design is where it all started for Crosley and is still going strong.
This small suitcase has a playful appearance and because it’s so easy to use, everyone can (re)discover the magic
of vinyl. The Cruiser record player is now upgraded with 2-way Bluetooth, which makes it possible to connect an
external Bluetooth speaker for an amplified sound.

• 3-speed record player
• Plays 7”, 10” or 12” records
• 2 Built-in speakers | 3”, 4Ω, 3W
• NP6 needle
• Belt-driven
• Pitch control
• Bluetooth input & output
• Aux in
• Headphone Jack
• RCA output
• AC power adapter (EU & UK PLUG)
• 35.5 cm (l) 25.5 cm (w) 10 cm (h)
• Weight: 2.5 kg
• Autostop

Now with 2-way Bluetooth!

A record player accessible to everyone. The Cruiser design is where it all started for Crosley and is still going strong.
This small suitcase has a playful appearance and because it’s so easy to use, everyone can (re)discover the magic
of vinyl. The Cruiser record player is now upgraded with 2-way Bluetooth, which makes it possible to connect an
external Bluetooth speaker for an amplified sound.

• 3-speed record player
• Plays 7”, 10” or 12” records
• 2 Built-in speakers | 3”, 4Ω, 3W
• NP6 needle
• Belt-driven
• Pitch control
• Bluetooth input & output
• Aux in
• Headphone Jack
• RCA output
• AC power adapter (EU & UK PLUG)
• 35.5 cm (l) 25.5 cm (w) 10 cm (h)
• Weight: 2.5 kg
• Autostop

This neat record player with a wooden look will easily blend into any kind of interior. The Crosley Gig will be the centre piece in the room, but it’s still modest enough to leave space for the rest.
Round out your mid-century modern decor with functional art from Crosley. Inspired by furniture from the 50s and early 60s, the Gig’s minimalistic design features sleek rounded edges and a faux wood finish with a matte black front face for contrast. Three knobs on the front allow you to easily crank up the volume, adjust pitch, switch between vinyl, aux-in or the built-in Bluetooth receiver, letting you play digital music through the record player. Use the matching speakers or the RCA outputs on the back to easily integrate into your existing music system. The Gig is a complete two-speed turntable system that’s ready to jam right out of the box.

• 2-speed record player (33 1/3 & 45 RPM)
• Plays 7”, 10” or 12” records
• 2 external full-range stereo speakers - 3”, 8Ω, 5W
• Built-in Bluetooth Receiver
• Pre-Mounted Moving Magnet Cartridge
• NP5 diamond needle
• Belt-driven
• Adjustable Pitch Control
• Bluetooth input
• Aux in
• RCA out
• AC power adapter (EU & UK PLUG)
• Dimensions: 43 cm (l), 28 cm (w), 10 cm (h) | Speakers: 18 cm (l), 10 cm (w), 10 cm (l)
• Weight: 5.8 kg

Fits Pioneer PLX-1000, PLX-500 and Technics SL-1200/1210 Mk1, Mk2, Mk3, Mk4, Mk5, Mk5G & Mk6 turntables. Designed and engineered in the UK. Sleek smoked/clear polycarbonate shell provides high level of protection, preserving the lifespan of your turntable. Simple push fit design shields tone-arm from accidental damage whilst making allowances for cables, your turntable can sit ready for operation. At home, on the road or in the club, Decksaver has your turntable covered.

Weight: 0.633 kg
Cover Dimension 45.6 × 35.5 × 7.5 cm
Fits: Technics SL-1200, SL-1210 (MK1-MK7/GR), Pioneer PLX-1000, PLX-CRSS12 and Mixars LTA/STA, Germini PT1000 turntables

FULLY AUTOMATIC PLUG & PLAY-TURNTABLE

The uncomplicated one from Dual with aspirations. The CS 329 uses sophisticated technology for entry-level analogue music playback.

With Plug & Play, you get a complete, ready-to-use package; all components are pre-assembled and permanently set. Plug in and get started!

As a fully automatic machine, the CS 329 offers ideal convenience. The tonearm swivels, lowers and raises autonomously at the touch of a button. All you have to do is put on the record and press the start button.

DETAILS:
Plinth: MDF - Plastic
• Elastomer vibration absorber integrated inside the feet
• Removable dust cover
Platter: Aluminium Die-cast
• Precise aluminium die-cast
• Heavy rubber mat for resonance damping
Tonearm: Straight, Plug and Play
• Plug & Play: all adjustments are factory fixed
• All functions can be fully automatic or manual
Drive: DC- Motor / Belt
• Rubber mountings for vibration decoupling
• Precision cut belt for lower wow & flutter

TECHNICAL SPECIFICATIONS:
Motor:
• Drive: Belt
• Speed settings: 33/45
• Wow & Flutter: < ±0,12 % (DIN WTD)

Tonearm:
• Auto-Start/-Stop-Function: Automatic
• Bearing: Ball-bearing
• Effective length: 221,5 mm
• Offset Angle: 25,6°
• Overhang: 19 mm
• Type: statically balanced
• Stylus Pressure Range: Fixed
• Cartridge Weight Range: N / A
• Factory installed pick up: Audio-Technica AT91

Platter:
• Material: Aluminium die-cast
• Mat: Rubber 2,5 mm
• Bearing: Hardened steel spindle Brass bushing (inverted)
• Diameter: 297 mm
• Weight (incl. Mat): 667 g

Plinth:
• Material: Plastic / MDF
• Surface finish: Black
• Feet: Ø 62 mm / Elastomer
• Connection: RCA cable (fixed)
• Connection to Phono Input: ✓
• Connection to Line Input: ✓
• Digital Output: ✕
• Dimension, closed dustcover: 435 x 372 x 132 mm
• Dimension, open dustcover: T: 405 mm / H: 390 mm
• Weight: 5 kg
• Power plug AC / DC: External power supply

Manual: https://hifi.dual.de/wp-content/uploads/2022/09/BDA-CS-329_manual_V1_DE_EN.pdf

THE MANUALRECORD PLAYER ENTRY

Emphasis on high component precision is a feature of the entire range of Dual products. This is the case for the entry model CS 418, which uses the same platform as the higher models in the product range.

The Ortofon 2M Red pickup and a switchable MM-phonopreamplifier are an integral part of this ready to run package.

The CS 418 is not attractive just because it is excellent value for money, but it also offers a superb and compelling balanced sound experience and a 5 year warranty for long term ownership.

DETAILS:
Plinth: Solid MDF
• Folded MDF construction with a black vinyl veneer
• Elastomer vibration absorber integrated inside the feet
• Removable dust cover

Platter: Aluminium Die-cast
• Precise aluminium die-cast
• Heavy rubber mat for resonance damping
• Solid platterbearing with a hardened steel spindle in a brass bushing

Tonearm: Straight, statically balanced
• Solid aluminium construction with ball-bearings
• Damped tonearmlift
• Adjustable trackingforce and antiskating

Drive: DC- Motor / Belt
• Low vibration DC-Servo-Motor
• Rubber mountings for vibration decoupling
• Precision cut belt for lower wow & flutter

TECHNICAL DATA:
Drive:
• Drive: Belt
• Speed settings: 33/45/78
• Wow & Flutter: < ±0,1 % (DIN WTD)

Tonearm:
• Auto-Start/-Stop-Function: ✕
• Bearing: Ball-bearing
• Effective length: 221,5 mm
• Offset Angle: 25,6°
• Overhang: 19 mm
• Type: statically balanced
• Stylus Pressure Range: 0 g to 4 g
• Cartridge Weight Range: 5 g to 9 g
• Factory installed pick up: Ortofon 2M Red

Platter:
• Material: Aluminium die-cast
• Mat: Rubber 2,5 mm
• Bearing: Hardened steel spindle, Brass bushing
• Diameter: 305 mm
• Weight (incl. Mat): 850 g

Plinth:
• Material: MDF, folded
• Surface finish: Vinyl veneer / Black
• Feet: Ø 62 mm / Elastomer
• Connection: RCA socket
• Connection to Phono Input: ✓
• Connection to Line Input: ✓
• Digital Output: ✕
• Dimension, closed dustcover: 435 x 367 x 145 mm
• Dimension, open dustcover: T: 415 mm / H: 400 mm
• Weight: 5,8 kg
• Power plug AC / DC: External power supply

Manual: https://hifi.dual.de/wp-content/uploads/2022/07/BDA-CS-418_manual_V4_DE_EN.pdf

FULLY AUTOMATIC HIFI-TURNTABLE

The fully automatic function of the CS 429 provides maximum ease of use. The tonearm automatically lifts, shifts across and drops with the push of a button. Simply place the vinyl record on the platter and push the start button.

The CS 429 has a fully adjustable tonearm. This provides the option to change the pickup in the future and to alter the trackingforce and anti-scating accordingly.

The internal rubber damping construction decouples the tonearm and platter from external vibrations. This very quiet platform pro-vides an excellent sound performance combined with precise, optical speed control.

DETAILS:
Plinth: Solid MDF
• MDF construction with internal vibration absorber
• Elastomer vibration absorber integrated inside the feet
• Removable dust cover

Platter: Aluminium Die-cast
• Precise aluminium die-cast
• Heavy rubber mat for resonance damping
• Solid platterbearing with a hardened steel spindle in a brass bushing

Tonearm: Straight, statically balanced
• All functions can be fully automatic or manual
• Solid aluminum construction with ball-bearings
• Adjustable trackingforce and antiskating

Drive: DC- Motor / Belt
• Precise optical speed control
• Rubber mountings for vibration decoupling
• Precision cut belt for lower wow & flutter

TECHNICAL DATA:
Drive:
• Drive: Belt
• Speed settings: 33/45/78
• Wow & Flutter: < ±0,08 % (DIN WTD)

Tonearm:
• Auto-Start/-Stop-Function: Automatic
• Bearing: Ball-bearing
• Effective length: 221,5 mm
• Offset Angle: 25,6°
• Overhang: 19 mm
• Type: statically balanced
• Stylus Pressure Range: 0 g to 4 g
• Cartridge Weight Range: 5 g to 9 g
• Factory installed pick up: Ortofon 2M Red

Platter:
• Material: Aluminium die-cast
• Mat: Rubber 2,5 mm
• Bearing: Hardened steel spindle, Brass bushing
• Diameter: 305 mm
• Weight (incl. Mat): 850 g

Plinth:
• Material: MDF, folded
• Surface finish: Vinyl veneer / Black
• Feet: Ø 62 mm / Elastomer
• Connection: RCA socket
• Connection to Phono Input: ✓
• Connection to Line Input: ✓
• Digital Output: ✕
• Dimension, closed dustcover: 435 x 367 x 145 mm
• Dimension, open dustcover: T: 415 mm / H: 400 mm
• Weight: 6,2 kg
• Power plug AC / DC: External power supply

Manual: https://hifi.dual.de/wp-content/uploads/2022/07/BDA-CS-429_manual_V4_DE_EN.pdf

MANUAL HIFI-TURNTABLE WITH FULL CARDAN TONEARM

For the true Vinyl Enthusiast, the CS 518 is equipped with a twin gimbal tonearm design using pivot ball-bearings for optimal precision.
This superior tonearm has the ability to guide even high end pickups with the greatest degree of precision and reliability.
The Ortofon 2M Red pickup and a switchable MM-phonopreamplifier are an integral part of this ready to run package.

DETAILS:
Plinth: Solid MDF
• Folded MDF construction with a black vinyl veneer
• Elastomer vibration absorber integrated inside the feet
• Removable dust cover

Platter: Aluminium Die-cast
• Precise aluminium die-cast
• Heavy rubber mat for resonance damping
• Solid platterbearing with a hardened steel spindle in a brass bushing

Tonearm: Twin Gimbal Design
• Straight, statically balanced
• Solid aluminium construction with precision pivot ball-bearing
• Adjustable trackingforce and antiskating

Drive: DC- Motor / Belt
• Low vibration DC-Servo-Motor
• Rubber mountings for vibration decoupling
• Precision cut belt for lower wow & flutter

TECHNICAL DATA:
Drive:
• Drive: Belt
• Speed settings: 33/45/78
• Wow & Flutter: < ±0,1 % (DIN WTD)

Tonearm:
• Auto-Start/-Stop-Function: ✕
• Bearing: 4 x Pivot ball-bearing / twin gimbal mounting
• Effective length: 221,5 mm
• Offset Angle: 25,6°
• Overhang: 19 mm
• Type: statically balanced
• Stylus Pressure Range: 0 g to 4 g
• Cartridge Weight Range: 5 g to 9 g
• Factory installed pick up: Ortofon 2M Red

Platter:
• Material: Aluminium die-cast
• Mat: Rubber 2,5 mm
• Bearing: Hardened steel spindle, Brass bushing
• Diameter: 305 mm
• Weight (incl. Mat): 850 g

Plinth:
• Material: MDF, folded
• Surface finish: Vinyl veneer / Black
• Feet: Ø 62 mm / Elastomer
• Connection: RCA socket
• Connection to Phono Input: ✓
• Connection to Line Input: ✓
• Digital Output: ✕
• Dimension, closed dustcover: 435 x 367 x 145 mm
• Dimension, open dustcover: T: 415 mm / H: 400 mm
• Weight: 5,9 kg
• Power plug AC / DC: External power supply

Manual: https://hifi.dual.de/wp-content/uploads/2022/07/BDA-CS-518_manual_V4_DE_EN.pdf

UNCOMPLICATED WITH COMFORT
The CS 529 combines ease of use of a fully automatic turntable with high-end solutions such as precision pivot ball-bearings in a twin gimbal tonearm.

The operation is just as straight forward as every automatic turntable; the tonearm automatically lifts, shifts across and drops with the push of a button. Simply place the vinyl record on the platter and push the start button.

All turntable functions can be controlled via the terminal or remotely operated via the Bluetooth signal, which also transmits the music data. The relevant app can be installed on any smart device to enable you to control the entire turntable remotely. This is the first product world-wide with such a feature.

DETAILS:
Plinth: Solid MDF
• Subchassis construction with rubber dampers
• Bluetooth for audio and remote-control functions
Platter: Aluminium
• Aluminium die-cast, long term precision
• Heavy rubber mat for resonance damping
• Hardened steel spindle in a brass bushing
Tonearm: Twin Gimbal Design
• All functions are fully automatic or manual
• Solid aluminium gimbal construction
• Pivot ball-bearings
Drive: DC- Motor / Belt
• Optical speed control at the motor
• Rubber mountings for vibration decoupling
• Precision cut belt for lower wow & flutter

TECHNICAL SPECIFICATIONS:
Motor:
• Drive: Belt
• Speed settings: 33/45/78
• Wow & Flutter: < ±0,08 % (DIN WTD)

Tonearm:
• Auto-Start/-Stop-Function: Bluetooth Remote Control / Automatic
• Bearing: 4 x ball-bearing / twin gimbal mounting
• Effective length: 221,5 mm
• Offset Angle: 25,6°
• Overhang: 19 mm
• Type: statically balanced
• Stylus Pressure Range: 0 g bis 4 g
• Cartridge Weight Range: 5 g bis 9 g
• Factory installed pick up: Ortofon 2M Red

Platter:
• Material: Aluminium die-cast
• Mat: Rubber 2,5 mm
• Bearing: Hardened steel spindle Brass bushing
• Diameter: 305 mm
• Weight (incl. Mat): 850 g

Plinth:
• Material: MDF, folded
• Surface finish: Vinyl veneer / Black
• Feet: Ø 62 mm / Elastomer
• Connection: RCA socket
• Connection to Phono Input: ✓
• Connection to Line Input: ✓
• Digital Output: Bluetooth Bluetooth 5.2 aptXT HD Audio.
• Dimension, closed dustcover: 435 x 367 x 145 mm
• Dimension, open dustcover: T: D: 415 mm / H: 400 mm
• Weight: 6,7 kg
• Power plug AC / DC: External power supply

MANUAL HIFI-TURNTABLE

For decades, direct-drive turntables from Dual have been renowned for their quality and reliability. The rumble free direct-drive in the CS 618Q keeps the RPM totally stable, while operating without noise or vibration.

The advanced twin gimbal precision tonearm is partnerd with an Ortofon 2M Blue pickup.

The turntable comes with an auto-stop feature that includes an automatic tonearm lift to reduce wear and tear on the needle as it moves to the end of the record.

DETAILS:
Plinth: Solid MDF
• Surface Options: Vinyl veneer, Gloss paint, Walnut veneer
• Elastomer vibration absorber integrated inside the feet
• Removable dustcover

Platter: Aluminium Die-cast
• Heavy aluminium die-cast platter
• Heavy rubber mat for resonance damping
• Hardened steel spindle integrated into the direct-drive

Tonearm: Twin Gimbal Design
• Autostop function with an automatic tonearmlift
• Solid aluminium construction with precision pivot ball-bearing
• Adjustabel trackingforce and antiskating

Drive: Direct-drive
• Quartz stabilised, high end direct-drive
• No vibrations through coreless inductors
• Double shielded Rotormagnets to eliminate any stray magnetic fields

TECHNICAL DATA:
Drive:
• Drive: Direct-drive
• Speed settings: 33/45/78
• Wow & Flutter: < ±0,07 % (DIN WTD)

Tonearm:
• Auto-Start/-Stop-Function: Auto-Stop / Auto Tonarmlift
• Bearing: 4 x Pivot ball-bearing /twin gimbal mounting
• Effective length: 221,5 mm
• Offset Angle: 25,6°
• Overhang: 19 mm
• Type: statically balanced
• Stylus Pressure Range: 0 g to 4 g
• Cartridge Weight Range: 5 g to 9 g
• Factory installed pick up: Ortofon 2M Blue

Platter:
• Material: Aluminium die-cast
• Mat: Rubber 2,5 mm
• Bearing: Hardened steel spindle, Brass bushing
• Diameter: 305 mm
• Weight (incl. Mat): 1450 g

Plinth:
• Material: MDF, folded
• Surface finish: Vinyl veneer / Black
• Feet: Ø 62 mm / Elastomer
• Connection: RCA socket
• Connection to Phono Input: ✓
• Connection to Line Input: ✓
• Digital Output: ✕
• Dimension, closed dustcover: 435 x 367 x 145 mm
• Dimension, open dustcover: T: 415 mm / H: 400 mm
• Weight: 7 kg
• Power plug AC / DC: External power supply

Manual: https://hifi.dual.de/wp-content/uploads/2022/07/BDA-CS-618Q_manual_V6_DE_EN.pdf

Smooth vinyl precision.

ELAC’s Miracord 50 Turntable is designed to deliver exceptional vinyl transcription, inspired by the iconic Miracord name from the Golden Age of Stereo, when turntables reigned supreme. The Miracord 50 is carefully engineered with a belt-drive motor and die-cast aluminum platter. A precision static balanced, straight-tube tonearm with removable headshell features a factory-mounted MM phono cartridge. Designed with convenience in mind, the Miracord 50 is equipped with a built-in defeatable phono preamplifier, allowing you to add this turntable to virtually any music system.

SPECIFICATIONS

Turntable Section
• Drive System: Belt drive
• Motor: DC motor
• Selectable Speeds: 33⅓ and 45 rpm
• Motor Servo: Speed rotation and servo system
• Rotation Speed Variation: +/-1%
• Wow and Flutter: 1%
• Signal-to-Noise Ratio: -67 dB or higher (A-weighted) -60 dB or higher (unweighted)
• Platter: Aluminum die-cast
• Platter Diameter: 0 in / 300 mm

Tonearm Section
• Type: Aluminum tube, static-balanced
• Effective Arm Length: 8 in / 223.6 mm
• Stylus Pressure Range: 0 to 0 g
• Cartridge Weight Range: 5 to 6.0 g
• Effective Arm Mass: 4 g
• Overhang: 6 mm
• Offset Angle: 25 degrees
• Anti-Skating: Adjustment Supported
• Main Bearing: Stainless steel

Cartridge Section:
• Type: Audio-Technica AT91 moving magnet
• Stylus Construction: Bonded diamond
• Mount: Half-inch
• Frequency Response: 20 Hz to 20 kHz
• Channel Separation: >18 dB
• Channel Balance: 5 dB
• Vertical Tracking: Angle 20 degrees
• Stylus Pressure: 0 g +/-0.5 g
• Cartridge Weight: 0 g +/-0.5 g
• Headshell Weight: 0 g (including screws, nuts and wires)

Phono Equalizer Amplifier
• Type :Moving magnet (MM)
• Phono Output: 5 mV (1 kHz, 3.54 cm/sec)
• Line Output: 140 mV (-17 dBV)
• Phono/Line: Switchable
• Supported Load Impedance: 47 kΩ

Connector: RCA pin jack including RCA cable accessories
Voltage: 100 to 240 V AC / 50 to 60 Hz
Power Consumption: 1.5 W (less than 0.5 W at standby)
Dimensions: (WXHXD) 5.5 x 16.05 x 14.20
Weight: 12.10 lb

Tech Sheet: https://elac-content.s3.amazonaws.com/uploads/2018/08/Miracord-50-Turntable_8-8-18.pdf

The Gemini TT-4000 High Torque direct drive turntable features a redesigned chassis with reinforced cabinet construction. The TT-4000 uses a precision-machined die-cast aluminum platter for a stable stand in the club. The shock-absorbing rubber feet absorb shock or vibration during operation.

It is ideal for DJs, audiophiles and casual listeners alike. The 16-pole brushless 3-phase DC motor drives the TT-4000's direct drive. The turntable features precise pitch control of +/- 10%. A statically balanced S-shaped tonearm features a hydraulic lift and anti-skate mechanism.

For those who want to digitize their record collection, the Gemini TT-4000 offers a USB port for connection to PC/Mac. This way you can easily record and digitize your vinyl albums.

Thanks to a built-in phono preamp that allows for a line-level output, the TT-4000 does not require grounding.

Features:
• Direct drive turntable with very powerful torque
• Ideal for DJing, listening to music or digitizing
• USB port for connection to PC/Mac
• Very strong torque of 4.5 kg/cm
• Balanced tonearm in S-shape
• Damped rubber feet absorb shocks and vibrations
• Phono preamp with line output built in - no grounding required
• Pitch control of +/- 10%

Technical data:
• Direct driven DC motor with high torque (4.5 kg/cm)
• Signal-to-noise ratio: 40 dB
• Turntable weight: 523 g
• Pitch adjustment: +/- 10%
• Audio interface: USB 2.0 | sampling rate: 48k, 44.1k, 16 bit
• Power consumption: approx. 5.5 W
• Power supply: AC 115V - 60Hz | 230V - 50Hz
• Weight: 6.35 kg
• Dimensions (W x D x H): 490 x 315 x 262 mm

Scope of delivery:
• Gemini TT-4000 Turntable
• Power cable
• RCA cable
• Headshell with pickup/stylus
• Slipmat
• 45 adapters
• User manual & warranty information
• Audacity Software CD V2.1.3

The Reloop SPiN Tone Arm by Jesse Dean Designs.

Straight outta SoCal.

Easy installation for your Reloop SPiN.

Engineered to work with;

- Ortofon OM style
- Reloop OM-GT
- Shure M44-7

Super stable design and accepts all magnetic cartridges!

- Constructed from FR4 fibre board
- Adjustable brass counter weight
- Front LED target light
- Phono analogue pre-amp included
- Magnetic clip for housing
- Easy wire installation kit, including cartridge mounting screws

Match it with a JDDX2R-SP SPiN contactless fader!?

Please note: The JDD-SPCB does not include a cartridge and stylus.

Installation Video: https://www.youtube.com/watch?v=NyBZpw0tuhw&feature=youtu.be&fbclid=IwAR32dn4iAJAp5fNS8pGmC8_vYDIPBIhEV_y1YNBRQYoEJ5Eeu5igEldFFHw

Introducing the new budget build tone arm by Jesse Dean Designs!

Compatible with any PT01 or Handytrax portable turntable!
Straight outta SoCal.
Battle tested at Portablist Lounge.
Easy install.

A far superior improvement over the factory tone arm.

• Constructed from Fr4 fiberboard
• ABS molded gimbal
• Adjustable brass counter weight
• Front LED target light
• Preamp included - no soldering required
• Magnetic clip for housing

Engineered to work with almost every cartridge like:
• Ortofon OM style
• Reloop OM-GT
• M447

Please note: The JDDPTA-PCB does not include a cartridge and stylus.

JDDPTA-PCB installation video: https://www.youtube.com/watch?v=5dHAPSt4yfo&feature=youtu.be&fbclid=IwAR1xzjGcWeySRyexDii-fJI_-1S5B2lr4h6NaRTuuQ4_9uEKaECb62LDDD0

Introducing the new budget build tone arm by Jesse Dean Designs!

Compatible with any PT01 or Handytrax portable turntable!
Straight outta SoCal.
Battle tested at Portablist Lounge.
Easy install.

A far superior improvement over the factory tone arm.

• Constructed from Fr4 fiberboard
• ABS molded gimbal
• Adjustable brass counter weight
• Front LED target light
• Preamp included - no soldering required
• Magnetic clip for housing

Engineered to work with almost every cartridge like:
• Ortofon OM style
• Reloop OM-GT
• M447

Please note: The JDDPTA-PCB does not include a cartridge and stylus.

JDDPTA-PCB installation video: https://www.youtube.com/watch?v=5dHAPSt4yfo&feature=youtu.be&fbclid=IwAR1xzjGcWeySRyexDii-fJI_-1S5B2lr4h6NaRTuuQ4_9uEKaECb62LDDD0

Introducing the new budget build tone arm by Jesse Dean Designs!

Compatible with any PT01 or Handytrax portable turntable!
Straight outta SoCal.
Battle tested at Portablist Lounge.
Easy install.

A far superior improvement over the factory tone arm.

• Constructed from Fr4 fiberboard
• ABS molded gimbal
• Adjustable brass counter weight
• Front LED target light
• Preamp included - no soldering required
• Magnetic clip for housing

Engineered to work with almost every cartridge like:
• Ortofon OM style
• Reloop OM-GT
• M447

Please note: The JDDPTA-PCB does not include a cartridge and stylus.

JDDPTA-PCB installation video: https://www.youtube.com/watch?v=5dHAPSt4yfo&feature=youtu.be&fbclid=IwAR1xzjGcWeySRyexDii-fJI_-1S5B2lr4h6NaRTuuQ4_9uEKaECb62LDDD0

Contactless Fader by Jesse Dean for your Reloop SPIN turntable.

The JDDX2R-SP is the same design built of the legendary JDDX2RS-A - with extra capability!

No need to take out and calibrate each time - calibrate from the top!

It’s dual rail slide contactless element gives it durability for an aggressive environment. This long-lasting fader has no audio bleed thanks to its magnetic sensors and circuitry. There is virtually no cleaning needed with this contactless element.

- Dual rail 45mm slider for stability and smooth action
- Magnetic sensor contactless circuitry
- Two side cut-in adjustment
- Switchable from double cut to 2 channel capability
- FR4 fiberglass PCB faceplates
- Full size fader cap by Cooler Caps!
- 30 second easy installation
- Comes with cut adjuster screw driver

JDDX2R-SP calibration instructions: http://www.zendell.uk/LINKS/JDDX2RS-A_calibration.pdf

JDDX2R-SP double cut instructions: http://www.zendell.uk/LINKS/JDDX2R-SP.pdf

Jesse Dean Contactless Scratch Fader for your Stanton STX portable turntable.

The all new high performance fader for ultra fast cuts.

Digitally controlled.

The fader features billet aluminum rail blocks for a robust construction.

Extremely easy cut-In adjustment without having to remove your fader.
Simply calibrate your fader from the top!

45mm glider travel with standard mounting hole pattern for preferred alignment.

Kit includes:

• JDDX2R-SX fader
• Black JDD fader plate
• Black fader cap
• Mini screwdriver for cut adjustment

JDDX2R-SX calibration instructions: https://www.youtube.com/watch?v=Gm3RpM8ughI&t=3s
Stock fader calibration instructions: https://www.youtube.com/watch?v=4o4nG07CUcA

OEM Replacement Pitch Potentionmeter for Technics SL 1200 MkII

Easy install.

• Improved carbon element
• No zero 'detent click' for accuracy
• Super smooth
• 105mm travel
• Suitable for SFDZ122N11 or SFDZ122N11-1

PROS
•USB port
•Removable plastic cover and built-in stereo preamp
•Mechanical tonearm lifter

PRODUCT INFORMATION
•Its trendy design and modern technology make this turntable perfect for all enthusiasts. The Lenco L-3808 is available in 4 colours: white,black, silver and matt grey.

•Do you want to play your favourite sounds of the past for your children? The Lenco L-3808 produces a superb high-quality sound. Your children will be amazed. Because this midi turntable is so easy to use, you can even let them play a record. The Lenco L-3808 is equipped with a mechanical tonearm lifter, a moving magnet cartridge (MMC) and a built-in preamp. You can play records at two speeds: 33 RPM and 45 RPM. A removable plastic cover protects the turntable from dust.

•As the years have passed, your records may have become old and fragile. To prevent your favourite music being lost for ever, you can digitise your cherished vinyl collection using the Lenco L-3808. Connect the turntable to your computer via the USB port and the job will be done in next to no time. Wherever you go, you will always have your favourite music with you.

SPECIFICATIONS
•SKU: A003073
•Product height: 15.10 cm
•Product depth: 34.80 cm
•Product width: 44.80 cm
•Number of RCA outputs: 1
•Power option: non-detachable AC-cable, Power on/off switch, AC
•USB connectors: USB A
•Type of drive: Direct drive
•Turntable rpm: 33 rpm, 45 rpm
•GTIN / EAN: 8711902040637
•Amplifier options: Includes (pre) amplifier, Pre-set Equaliser
•Functional storage media: USB support
•Material: Plastic
•Manufacturer's warranty: 24 months
•Maximum power consumption: 11W

Direct drive turntable with USB recording

• Recording Vinyl music through PC
• Integrated stereo pre-amplifier
• 2 rated speed settings 33 RPM and 45 RPM
• Moving Magnetic Cartridge (MMC)
• Mechanical arm lift
• Direct drive
• Removable plastic dust cover
• Included: USB cable, RCA cable
• Connection: USB-PC, RCA line output
• Measurements: 415 x 150 x 333 mm

Direct drive turntable with USB recording

• Recording Vinyl music through PC
• Integrated stereo pre-amplifier
• 2 rated speed settings 33 RPM and 45 RPM
• Moving Magnetic Cartridge (MMC)
• Mechanical arm lift
• Direct drive
• Removable plastic dust cover
• Included: USB cable, RCA cable
• Connection: USB-PC, RCA line output
• Measurements: 415 x 150 x 333 mm

PROS
•Modern turntable
•Bluetooth
•33 or 45 RPM

PRODUCT INFORMATION
•The Lenco LBT-188 is a turntable with Bluetooth functionality. Connecting this turntable to your Bluetooth speaker is child’s play. The ideal set-up for enjoying a full and warm sound while lounging on your couch at home. Retrieve your old records from the attic and play them on this modern turntable. Enjoy the crystal-clear sound of your vinyl, both old and new. Switch from 33 to 45 revolutions to play your vinyl record at the right speed.

•The LBT-188 from Lenco features a metal turntable, belt drive, an RCA connection and a tone arm with a counterweight. The plastic cover ensures that your turntable does not disappear under a layer of dust and protects it against knocks. A CE-UK multi-plug AC power supply comes with the turntable.

SPECIFICATIONS
•SKU: A003117
•Product height: 12.40 cm
•Product depth: 34.40 cm
•Product width: 41.70 cm
•Number of RCA outputs: 2
•12V car: Yes
•Power option: Power on/off switch
•USB connectors: USB A
•Type of drive: Belt drive
•Turntable rpm: 33 rpm, 45 rpm
•GTIN / EAN: 8711902041139
•Amplifier options: Includes (pre) amplifier
•Material: Plastic
•Manufacturer's warranty: 24 months
•Maximum power consumption: 5 W

PROS
•Modern turntable
•Bluetooth
•33 or 45 RPM

PRODUCT INFORMATION
•The Lenco LBT-188 is a turntable with Bluetooth functionality. Connecting this turntable to your Bluetooth speaker is child’s play. The ideal set-up for enjoying a full and warm sound while lounging on your couch at home. Retrieve your old records from the attic and play them on this modern turntable. Enjoy the crystal-clear sound of your vinyl, both old and new. Switch from 33 to 45 revolutions to play your vinyl record at the right speed.

•The LBT-188 from Lenco features a metal turntable, belt drive, an RCA connection and a tone arm with a counterweight. The plastic cover ensures that your turntable does not disappear under a layer of dust and protects it against knocks. A CE-UK multi-plug AC power supply comes with the turntable.

SPECIFICATIONS
•SKU: A003117
•Product height: 12.40 cm
•Product depth: 34.40 cm
•Product width: 41.70 cm
•Number of RCA outputs: 2
•12V car: Yes
•Power option: Power on/off switch
•USB connectors: USB A
•Type of drive: Belt drive
•Turntable rpm: 33 rpm, 45 rpm
•GTIN / EAN: 8711902041139
•Amplifier options: Includes (pre) amplifier
•Material: Plastic
•Manufacturer's warranty: 24 months
•Maximum power consumption: 5 W

PROS
•Modern turntable
•Built-in speakers
•Adjustable speed
•Output for headphones

PRODUCT INFORMATION
•The Lenco LS-10 is a modern turntable with two built-in speakers. Enjoy your favourite vinyl at a single press of a button. Forget complicated music systems, because the Lenco LS-10 effortlessly brings your records to life.

•Whatever the music genre you like listening to, you can change easily from 33 to 45 RPM. For more volume, you connect external speakers via the RCA jack on the back of the turntable. This ensures that you can fill any size of room with music. The turntable also has an output for headphones so that you can listen to your favourite music without disturbing anybody else.

•The Lenco LS-10 is supplied with a removable dust cover that protects the turntable from dirt. You can also easily clean the appliance with a soft, dry cloth. The stylus is easy to replace. The manual supplied with the turntable tells you how. The Lenco LS-10 guarantees you years of pleasure listening to music from the past, played on modern equipment.

SPECIFICATIONS
•SKU: A003102
•Product height: 10.30 cm
•Product depth: 31.80 cm
•Product width: 32.90 cm
•Number of speakers: 2
•Speaker options: Speakers integrated
•Number of RCA outputs: 1
•Power option: Power on/off switch, AC
•Type of drive: Belt drive
•Turntable rpm: 33 rpm, 45 rpm
•GTIN / EAN: 8711902040965
•Material: Plastic
•Manufacturer's warranty: 24 months
•Stand-by power consumption (ErP Directive): 0.5W
•Maximum power consumption: 6W
•Headphone connector: Yes

PROS
•Modern turntable
•Built-in speakers
•Adjustable speed
•Output for headphones

PRODUCT INFORMATION
•The Lenco LS-10 is a modern turntable with two built-in speakers. Enjoy your favourite vinyl at a single press of a button. Forget complicated music systems, because the Lenco LS-10 effortlessly brings your records to life.

•Whatever the music genre you like listening to, you can change easily from 33 to 45 RPM. For more volume, you connect external speakers via the RCA jack on the back of the turntable. This ensures that you can fill any size of room with music. The turntable also has an output for headphones so that you can listen to your favourite music without disturbing anybody else.

•The Lenco LS-10 is supplied with a removable dust cover that protects the turntable from dirt. You can also easily clean the appliance with a soft, dry cloth. The stylus is easy to replace. The manual supplied with the turntable tells you how. The Lenco LS-10 guarantees you years of pleasure listening to music from the past, played on modern equipment.

SPECIFICATIONS
•SKU: A003102
•Product height: 10.30 cm
•Product depth: 31.80 cm
•Product width: 32.90 cm
•Number of speakers: 2
•Speaker options: Speakers integrated
•Number of RCA outputs: 1
•Power option: Power on/off switch, AC
•Type of drive: Belt drive
•Turntable rpm: 33 rpm, 45 rpm
•GTIN / EAN: 8711902040965
•Material: Plastic
•Manufacturer's warranty: 24 months
•Stand-by power consumption (ErP Directive): 0.5W
•Maximum power consumption: 6W
•Headphone connector: Yes

PROS
•MDF housing
•2 loose speakers
•Selectable speed
•Bluetooth / Auto-stop

PRODUCT INFORMATION
•The Lenco LS-300 is a modern turntable with two loose speakers. Enjoy your favourite vinyl at a single press of a button. Forget complicated music systems, because the Lenco LS-300 effortlessly brings your records to life.

•Whatever the music genre you like listening to, you can change easily from 33 to 45 RPM. The 2 separate wooden speakers are powerful enough to fill any room with music. The turntable also features Bluetooth, making it easy to stream music from your smartphone.

•Lenco is fully aware that you want to treat your vinyl records as gently as possible, so the Lenco LS-300 features auto-stop. This function ensures that the record stops turning. This prevents scratching so that you can enjoy your beloved records for longer. The Lenco LS-300 is supplied with a plastic cover that keeps your Lenco free of dust during brief periods when you are not using your turntable. A CE-UK multi-plug AC power supply comes with the turntable.

SPECIFICATIONS
•SKU: A003105
•Product height: 15.20 cm
•Product depth: 35.00 cm
•Product width: 43.80 cm
•Number of speakers: 2
•Number of RCA outputs: 1
•12V car: Yes
•Power option: Power on/off switch, AC
•Type of drive: Belt drive
•Turntable rpm: 33 rpm, 45 rpm
•GTIN / EAN: 8711902040996
•Material: Wood
•Manufacturer's warranty: 24 months
•Stand-by power consumption (ErP Directive): 1W
•Maximum power consumption: 24W

PROS
•MDF housing
•2 loose speakers
•Selectable speed
•Bluetooth / Auto-stop

PRODUCT INFORMATION
•The Lenco LS-300 is a modern turntable with two loose speakers. Enjoy your favourite vinyl at a single press of a button. Forget complicated music systems, because the Lenco LS-300 effortlessly brings your records to life.

•Whatever the music genre you like listening to, you can change easily from 33 to 45 RPM. The 2 separate wooden speakers are powerful enough to fill any room with music. The turntable also features Bluetooth, making it easy to stream music from your smartphone.

•Lenco is fully aware that you want to treat your vinyl records as gently as possible, so the Lenco LS-300 features auto-stop. This function ensures that the record stops turning. This prevents scratching so that you can enjoy your beloved records for longer. The Lenco LS-300 is supplied with a plastic cover that keeps your Lenco free of dust during brief periods when you are not using your turntable. A CE-UK multi-plug AC power supply comes with the turntable.

SPECIFICATIONS
•SKU: A003105
•Product height: 15.20 cm
•Product depth: 35.00 cm
•Product width: 43.80 cm
•Number of speakers: 2
•Number of RCA outputs: 1
•12V car: Yes
•Power option: Power on/off switch, AC
•Type of drive: Belt drive
•Turntable rpm: 33 rpm, 45 rpm
•GTIN / EAN: 8711902040996
•Material: Wood
•Manufacturer's warranty: 24 months
•Stand-by power consumption (ErP Directive): 1W
•Maximum power consumption: 24W

Turntable with 4 speakers built-in and bluetooth reception

• Bluetooth 5.0
• 2 rated speed settings 33, and 45 RPM
• Moving Magnetic Cartridge (MMC)
• Belt drive
• Start & stop control
• Tone & Pitch control
• 4 built-in speakers
• Output power: 40W RMS
• Pre-amplifier ON-OFF
• Plastic dust cover
• P.U. leather finishing
• included: CE-UK multiplug AC Adaptor
• Connections: RCA output, AUX in, 3,5mm earphone jack
• Power source : AC 100~240V 60/50Hz
• Power consumpting max : 35W
• Dim. unit: 425 x 360 x 190 mm (WxDxH)