Turntables 145 Items

New motor, developed exclusively for direct-drive turntables

The TN-4D-SE uses a sleek, brushless DC motor, offering crystal-locked speed accuracy, regulated by a computer-controlled feedback circuit and achieving low wow-and-flutter levels for a direct drive turntable, especially one with such a stylish, low-profile design.

Knife-edge, pivot-point tonearm bearings

In collaboration with SAEC Corporation, a world-famous, high-end tonearm manufacturer, the TN-4D's tonearm employs a knife-edge, pivot-point bearing. Unlike the case for tonearms with conventional bearings, any fine vertical movements encountered by this tonearm actually help in delivering a more dynamic sound with excellent resolution. The S-shaped tonearm also employs a universal headshell fitting, allowing users to quickly and easily swap cartridges/headshells, and supports a wide range of cartridge weights (from 14 - 23g).

Precision anti-skating and stylus-pressure adjustment

As you might expect, the tonearm is equipped with a counterweight, for precise stylus-pressure adjustment, and an anti-skating mechanism.

Pre-installed Oyster cartridge by SUMIKO

The TN-4D-SE comes with a well-regarded Oyster MM cartridge from SUMIKO – a legendary American cartridge manufacturer. Regardless of the type of music, the Oyster cartridge delivers a powerful but insightful performance.

Built-in PHONO EQ amplifier supporting MM cartridges

The TN-4D-SE comes with a built-in PHONO EQ amplifier that allows you to directly connect the turntable to the line-level inputs of your existing hi-fi system. The NJM8080 IC from New Japan Radio Corporation is employed for op-amp duties, bringing up the level of the tiny signals received via the cartridge up to LINE level strength without any loss of quality.

Die-cast aluminium platter

In conjunction with the newly-developed motor, the high inertia, die-cast aluminium platter helps to achieve better speed stability.

Insulating feet with excellent shock absorption

The insulating feet comprise a machined aluminium shell topped with a rubber cushion that is fixed to the high-density MDF plinth. Thanks to their excellent shock absorption characteristics the TN-4D-SE is very resistant to acoustic feedback.

2-speed turntable for 33-⅓ and 45 rpm

The TN-4D-SE supports 33-⅓ and 45 rpm for LP and EP records. Our insistence on quality engineering can even be seen in the construction of the rotary control for start-up/speed selection, formed of machined aluminium.

Features at a glance:
• Direct-drive analog turntable
• Crystal-locked speed stability, thanks to a new brushless DC motor with feedback control
• Die-cast aluminium platter
• Knife-edge, pivot-point tonearm base, designed by high-end tonearm manufacturer SAEC
• Multi-layer piano black or natural walnut veneer finish
• Built-in PHONO EQ amplifier for high-quality sound (PHONO/LINE switchable)
• Audiophile-grade NJM8080 op-amp used in PHONO EQ stage
• 2-speed drive offering 33-⅓ and 45 rpm
• Gold-plated oxidation-resistant output connectors
• Oyster MM cartridge by SUMIKO
• Shock-absorbing insulating feet
• GND terminal
• RoHS compliant
• Included Accessories
• Felt Mat
• EP Adapter
• Counter Weight
• Head-shell (SUMIKO Oyster installed)
• Platter
• Dust Cover
• Hinges × 2
• RCA Audio cable with GND terminal
• AC Adapter (GPE036W-24015)
• Owner's Manual (including Warranty Card)

TURNTABLE FEATURES
• Type: Manual
• Drive method: Direct-drive
• Speed: 33 rpm, 45 rpm
• Wow & flutter: ≤ 0.1%
• Built-in preamp: Yes
• S/N ratio: 67dB
• Cartridge: SUMIKO Oyster
• Cartridge type: MM
• Cartridge output: 4.0mV (1kHz)
• Tracking force: 2.3g
• Cartridge weight: 5.3g
• Including headshell: 15.3g
• Rec. cartridge weight: 4-13g
• Rec. cartridge weight (incl. headshell): 14-23g

AUDIO OUTPUTS
• Output level & impedance phono (MM): 4.0mV (1kHz)
• RCA: 1
• Output level & impedance RCA: 224mV (–13dBV)

ENERGY MANAGEMENT
• Power consumption (standby): 0.5W
• Power consumption: 2W
• AC adapter power
- Input: AC 100 V – AC 240 V, 50/60 Hz
- Output: DC 24 V, 1500 mA

DIMENSIONS AND WEIGHT
• Product height: 11.7cm
• Product width: 42cm
• Product length: 35.6cm
• Product weight: 6.1kg
• Packsize height: 24cm
• Packsize width: 52.5cm
• Packsize length: 43.8cm

Refined in every aspect.

The Evolution
The Debut Carbon EVO focuses on the core aspects that make a turntable sound great. Technically correct design - expert craftsmanship - handmade in the EU. This turntable is built to last you a lifetime!

Redesigned motor suspension
We used our technology and experience gained from the past and fit damping techniques of highend turntables into the Debut Carbon EVO. Looking at more advanced TPE damping and highmass sandwich constructions we were able to come up with a new motor and suspension solution for the Debut Carbon EVO.

Anytime the perfect stand
Our new Debut Carbon EVO does not just look great - it also always stands perfectly level. It uses 3 height adjustable heavy-duty metal feet to ensure a level positioning on every surface.

Controlled playback speeds
Besides being able to effortlessly change replay speeds with the push of a button, the playback speed is electronically controlled with the utmost precision, which results in the most accurate and stable speeds.

DAMPED FROM THE INSIDE
Our previous metal platter was already heavier than anybody else‘s on the market, but metal platters inherently have a disadvantage: resonance.
Our TPE (thermoplastic elastomer) technology now helps to damp the resonance completely and also increases the weight to 1,7 kg. Because the TPE is mounted to the inside of the platter‘s rim, the moving energy will also create a flywheel effect. The result is an even quieter and noiseless operation with less wow and flutter.

CLEAN LOOK & NEW COLOURS
You wont find any button, switch or printing on the plinth to ensure the luxurious aesthetics. The speed control switch has been moved to the bottom of the plinth, to keep the clean look the Debut is known for.
The Debut Carbon EVO is not only timeless by offering traditional high-gloss black, white and red finishes or our fabled real-wood walnut veneer. Completely new, unique and trend-setting are the beautifully realized satin signature finishes in 5 different variations.

Ortofon 2M Red
Moving-Magnet Cartridge
2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth.

The Tonearm
8,6 inch carbon
The new Debut Carbon EVO features the proven 8,6‘‘ one piece Carbon tonearm design. The super stiff, but lightweight tonearm delivers an insane sound quality with a convincing sound stage.

Output
Gold plated sockets
You can always change your RCA output cable and upgrade it with your preffered one. The gold plated connectors will always provide the best connection.

Phono Cable
Semi-balanced RCA cable
To guarantee a perfect connection to your amp you will find a high-quality phono RCA cable in the box. Our Connect it E is a semi-balanced, low-capacitance cable, with superior shielding.

Suspension
Improved motor suspension
The Debut Carbon EVO features our new designed motor suspension. We have improved the old design to consistently reduce the vibrations better than before.

Metal Feet
Damped & height adjustable
The new Debut Carbon Evo stands on three height adjustable damped aluminium feet to guarantee the perfect stand.

1,7 kg Platter
Heavy steel and TPE damped
We added a TPE (thermoplastic elastomer) ring on the inside of the platter. The result is an even quieter and noiseless operation with less wow and flutter.

33/45/78 RPM
High precision motor control
The rocker switch on the bottom of the turntable allows you to change speeds with the push of only a single button.

Technical Specifications:
•Nominal speeds: 33/45 r.p.m.. *** 78 r.p.m. optional
•Speed variance: 33: ±0.50% 45: ±0.60%
•Wow and flutter: 33: ±0.17% 45: ±0.15%
•Signal to noise: 68dB
•Effective tonearm mass: 6g
•Effective tonearm length: 8.6 " ( 218.5 mm)
•Overhang: 18,5 mm
•Power consumption: 4 W/ 0 W in Stand-By
•Outboard power supply: 15V / 0 – 0.8 mA DC (set at 0.5 mA), universal power supply
•Dimensions (W x H x D): 415 x 118 x 320 mm, dust cover open 415 x 365 x 405mm
•Weight: 5,6 kg
•Dimensions packaging (W x H x D): 488 x 235 x 393 mm
•Weight incl. packaging: 8.0kg

MM-Cartridge Ortofon 2M Red:
•Frequency range: 20-22.000Hz
•Channel separation: 22dB/1kHz
•Output voltage: 5.5mV
•Recommended load impedance: 47kohms/amplifier connection – MM-input
•Compliance/stylus type: 20µm/mN – elliptical
•Recommended tracking force: 17.5mN
•Weight: 7.2g

Manual: https://www.project-audio.com/wp-content/uploads/2020/08/DebutCarbonEVO-Userguide.pdf

Pro-Ject‘s classic turntable design reimagined!

Real high-end features – True audiophile sound

The X1 is based on the same concept as the P1, but improved in every aspect thanks to modern materials and new production methods. Inside it houses a sophisticated DC/AC generator board which, combined with the convenient speed control board, delivers clean and stable power to the quiet-running motor. For even further improved performance, the motor is decoupled from the main plinth using a new motor suspension system. In the X1, the motor drives a new, heavy, non-resonant Acryl platter via a sub-platter drive system and a premium grade main bearing for liquid smooth rotation.

The X1 is also better than its predecessors, thanks to the super-stiff, perfectly tempered Carbon/Alu sandwich construction tonearm. This new 8.6” tonearm design is incredibly light and stiff, with improved resistance to external interference. Finished as a one-piece, with no resonance-inducing headshell, the X1 can also be set for azimuth and VTA adjustment. The tonearm is then supplied with a TPE-damped counterweight, further reducing cartridge-tonearm resonances.

Supplied with a brand new Pro-Ject Pick it S2 MM cartridge, manufactured by the cartridge experts at Ortofon but voiced by the design team at Pro-Ject, it can be ready to play within a few minutes of unboxing. Also supplied in the box is our Connect-IT E RCA cables, a semi-balanced, low-capacitance cable with superior shielding that’s optimized for turntable use. Lastly, height-adjustable feet in their Alu/ TPE sandwich construction are a very exclusive but necessary feature to level up the turntable and effectively isolate it from the surface it is place on. The X1‘s 8 layers of painting and the hand-polished finish guarantee its luxury appearance.

In the box:

X1 with Pick it S2 MM cartridge
Connect it E RCA Cable
Dust cover
Adapter for 7“ singles
Round drive belt for 78 r.p.m.
Power supply, allen key

Features
Speed control with electronic speed switch for ultimate speed stability
Carefully isolated motor for less vibration and noise
Sub-platter with extremely low 0.001mm bearing tolerances
Stainless steel platter-bearing with soft brass bushing and teflon mirrors for lowest rumble and noise, and a stable, accurate speed transmission
Resonance free, 1.5 kg heavy acryl platter
8,6” carbon/alu sandwich tonearm with best internal damping and TPE damped counterweight
Kardan ultra-low friction 4 pin point precision tonearm bearing
Ortofon Pick it S2 MM cartridge newly developed with Ortofon
Massive and heavy, precision CNC‘d MDF chassis
Luxury 8 layers of painting and hand-polished finish or real-wood, satin-waxed veneer
Super shielded, semi-symmetrical, low-capacitance Pro-Ject phono cables
Height adjustable, aluminium feet for massively reduced risk of acoustical feedback
Handmade in Europe

Technical Specifications
Speed 33, 45, 78 (electronic speed change)
Principle belt drive
Speed variance 33: 0.30% 45: 0.25%
Wow & flutter 33: 0.15% 45: 0.13%
Platter 20mm thick, 1.5 kg heavy acryl
Main bearing stainless steel/brass
Tonearm 8,6” carbon/aluminium sandwich
Effective arm length 218,5 mm
Overhang 18 mm
Effective tonearm mass 10,0g
Tracking force range 0 - 30mN
Included accessories 15volts DC /0,8A power supply, Dust cover, Connect it E Phono cable, feltmat
Power consumption 5,0 watts max /< 0.3 watt standby
Dimensions 415 x 125 x 335 mm (WxHxD)
Weight 7 kg net / 9.5 kg gross weight

Manual: https://www.project-audio.com/wp-content/uploads/2019/04/X1-Manual.pdf

Uncompromised heavyweight design combined with high-end features. The big brother of our X1 sets new standards.

Real high-end features.

Azimuth & VTA - Fully adjustable
The X2 comes with fully adjustable Azimuth & VTA. It offers you the possibility to modify your X2 as you want it.

Pick it 2M Silver - High-end cartridge
This cartridge uses internal silver plated copper coils, which guarantees outstanding sonic results! The X2 is available with or without the Pick it 2M Silver.

2 kg Platter - Resonance free acryl
The perfect platform to place your precious vinyl records, guaranteeing absolute reliability in its performance and sonic character.

33/45/78 RPM - High precision motor control
A sophisticated DC/AC generator board generates clean and stable power to drive the motor. Easily change speed with the push of only a single button.

New motor suspension
A good motor by itself, is already very quiet. To get the best performance out of it, we have improved the motor suspension. The X2‘s motor chassis is carefully balanced and suspended on a precision tuned TPE belt - this way the motor chassis is effectively decoupled from the main plinth for optimal performance.

The Tonearm - 9'' Carbon-Aluminium Tonearm
Finished as a one-piece, with no resonance-inducing headshell, the X2 can also be set for azimuth and VTA adjustment. The tonearm is then supplied with a TPE-damped counterweight.
Compared with its little brother the X1, the tonearm is longer - 9“ in length - and the tube has a wider diameter. The carbon/aluminium sandwhich construction results in better internal damping. The increased mass makes the tonearm an excellent fit for low compliance MC cartridges.

Metal Feet - Damped & height adjustable
The three height adjustable damped aluminium feet guarantee the perfect stand & massively reduce risk of acoustical feedback.

Phono Cable - Semi-balanced RCA cable
To guarantee a perfect connection to your amp you will find a high-quality phono RCA cable in the box. Our Connect it E is a semi-balanced, low-capacitance cable, with superior shielding.

Technical Specifications:
•Speed: 33, 45, 78 (electronic speed change)
•Principle: belt drive
•Speed variance: 33: 0.25% 45: 0.20%
•Wow & flutter: 33: 0.12% 45: 0.10%
•Signal to noise: 70 dB
•Platter: 30mm thick, 2 kg heavy acryl
•Main bearing: stainless steel/brass
•Tonearm: 9” carbon/aluminium sandwich
•Effective arm length: 230 mm
•Overhang: 18 mm
•Effective tonearm mass: 13,5g
•Tracking force range: 0 - 30mN
•Included accessories: 15volts DC /0,8A power supply, Dust cover, Connect it E Phono cable, feltmat
•Power consumption: 4,5 watts max / 0.3 watt standby
•Dimensions: 460 x 150 x 340 mm (WxHxD)
•Weight: 10 kg

Manual: https://www.project-audio.com/wp-content/uploads/2021/01/X2-Manual.pdf

The AT-LP3XBT is a fully automatic turntable designed to deliver outstanding analogue sound with enhanced Bluetooth® wireless technology.

Bringing the clarity and warmth of analogue audio to the digital generation, this Bluetooth® turntable offers all the benefits of vinyl with the convenience of enhanced connectivity. Enjoy the freedom to connect to the latest speakers or headphones with Bluetooth® wireless technology at just the touch of a button - your analogue listening journey starts here.

Audio-Technica’s LP3XBT turntable combines 60 years of high-fidelity design with the latest Bluetooth® technology, giving you cutting-edge features while drawing on decades of audio experience. Enjoy a turntable that’s built on heritage, but built with the modern listener in mind.

Featuring fully automatic operation, a built-in phono preamp, removeable universal headshell and replaceable stylus, this Audio-Technica turntable is easy to set up and use, making it an ideal choice for beginners or those looking to level up their listening experience. Play 33⅓ & 45 RPM records your way, experimenting with different styli as you begin to discover your personal audio preferences.

Integrated Bluetooth® technology gives you the flexibility to connect your turntable quickly and easily, no matter where you are or how you choose to enjoy your vinyl experience. Whether you pair your LP3XBT with speakers to provide the perfect soundtrack for a gathering with friends, or listen through a pair of Audio-Technica headphones for a deep listening session, you can expect impeccable high-fidelity audio.

Features:
• Fully automatic belt-drive turntable operation with two speeds: 33-1/3, 45 RPM
• High-fidelity audio with Bluetooth wireless technology
• Connects wirelessly to speakers and other devices equipped with Bluetooth wireless technology or to wired audio systems and powered speakers via included dual RCA output cable
• Compatible with the high-quality Qualcomm® aptX™ audio codec
• Balanced straight tonearm with hydraulically damped lift control and rest
• AT-VM95C cartridge is compatible with any VM95 Series replacement stylus, offering a wide choice of options for every budget and application
• Includes the AT-HS3 universal headshell
• Built-in switchable phono/line pre-amplifier with detachable dual RCA output cable with grounding wire
• Anti-resonance, die-cast aluminum platter with felt mat
• Damped base construction for reduced low-frequency feedback coloration
• Included Accessories: detachable RCA output cable (Dual RCA male to dual RCA male with ground), 45 RPM adapter, removable hinged dust cover, and detachable power cable

Specifications:
• Type Belt-drive, fully automatic operation
• Motor DC motor
• Drive Method Belt drive
• Speeds 33-1/3 RPM, 45 RPM
• Turntable Platter Die-cast aluminium
• Wow and Flutter < 0.2 % WRMS (33 RPM) at 3 kHz
• Signal-to-Noise Ratio > 60 dB
• Output Level PHONO: 4.0 mV nominal at 1 kHz, 5 cm/sec
• Output Level LINE: 252 mV nominal at 1 kHz, 5 cm/sec
• Phono Pre-Amp Gain 36 dB nominal, RIAA equalized
• Power Supply Requirements 100 to 240 V, 50/60 Hz, 0.6 A Max
• Power Consumption 2 W
• Dimensions 435.6mm (17") ×374 mm (15 ") ×128 mm (5.0") (W × D × H)
• Weight 5.0 kg (11 lbs)

Accessories Included:
• Dust cover
• Felt mat
• Platter (with drive belt)
• Dust cover hinges
• Counterweight
• Headshell (AT-HS3 BK) with VM stereo cartridge (AT-VM95C)
• 45-RPM adapter
• RCA audio cable (Approx. 1.0 m (3.3'))
• AC adapter (Approx. 1.5 m (4.9'))

Communication:
• Communication System Bluetooth version 5.2
• Frequency Band 2.402 GHz to 2.480 GHz
• Maximum RF Output 2,5 mW EIRP
• Maximum Communication Range Sichtlinie – ca. 10 m
• Modulation Method GFSK, Pi/4DQPSK, 8DPSK
• Compatible Bluetooth Profile A2DP
• Support Codec Qualcomm® aptX™ Adaptive Audio, Qualcomm® aptX™ Audio, SBC

Premium HiFi turntable with Ortofon 2M Blue cartridge

DESIGNED WITH PRECISION FROM THE OUTSET
The Turn X's direct-drive DC motor offers incredibly accurate and consistent speeds. The high torque ensures lightning-fast start-up times and minimal variances of just +/-0.03%. The Turn X excels when operated in full manual mode, where its electronic brake and rotary switch for smooth starting and stopping, which also doubles as a speed selector (33, 45 and 78 RPM), shine.

BALANCE PERFECTION
A solid aluminium block supports the record player's precision-machined die-cast platter. Its hefty 2.1 kg, 332 mm diameter and 22.5 mm thickness ensure smooth, even movement. The damping rubber coating on the back of the turntable and the rubber mat provide excellent isolation properties and minimise vibrations.

AUDIOPHILE TONEARM
The statically balanced S-shaped tonearm can be adjusted in height to change the cartridge's azimuth (the angle at which the needle approaches the record) and the record's vertical tracking angle (VTA). The tonearm design guarantees free and fluid movement and optimum cartridge performance.

CRYSTAL CLEAR SOUND QUALITY
The Turn X has a high-quality Ortofon 2M Blue cartridge pre-installed, ensuring excellent dynamics and sound resolution to satisfy even the most discerning audiophiles. Another highlight: The universal SME connector enables a quick and easy cartridge system change if required.

SOUND AND NOTHING BUT SOUND
The turntable's solid MDF chassis is exceptionally sturdy and robust, keeping unwanted resonances at bay from the outset. As a bonus, the Turn X is effectively decoupled thanks to the height-adjustable isolator feet.

DESIGN WITHOUT COMPROMISE
In addition to meeting the exacting demands of vinyl enthusiasts, the Reloop Turn X is a true visual showpiece. The record player's sleek design, sophisticated one-button control, and classy piano lacquer finish make it a real eye-catcher.

ATTENTION TO DETAIL
Last but not least, the Turn X features a gold-plated high-resolution phono output and a gold-plated ground connector for optimum signal transfer and corrosion resistance. Interference is reduced even further by the power switch's ultra-low noise insulation.

FEATURES:
• Quartz-controlled, premium HiFi turntable
• Super high torque, direct drive DC motor with ultra-precise rotation speed
• Extra-heavy, CNC machined 22,5 mm thick aluminium platter with rubber damping
• Quick start-up and drift-off rotation speed less than +/-0.03%
• Full manual operation with motor control-switch to select three different speeds (33, 45 and 78 RPM)
• Precision machined, extra heavy aluminium die-cast platter for a perfectly balanced rotation (305 mm diameter, 22.5 mm thick, 2.1 kg)
• Deadening rubber covering rear platter surface & special 5 mm rubber mat for optimized resonance control and damping
• Sunk-in platter cavity construction
• Static-balanced S-shaped tonearm with VTA adjustment
• Adjustable anti-skating wheel for optimal pick-up tracking
• Pre-installed Ortofon 2M Blue cartridge for excellent dynamics and sound resolution
• Universal headshell connector (SME) provides added flexibility
• Counterweight supplied supports a wide variety of cartridges
• Premium, high-resolution audio phono outputs (with separate grounding connection)
• Gold-plated, corrosion-resistant audio connections (detachable power and RCA cables)
• Built-in switching power with ultra-low noise isolation design
• Rigid construction, with extra-heavy, solid MDF wooden plinth
• Height-adjustable, shock-resistant insulator feet for effective decoupling
• Timeless design with high-gloss, black piano finish
• Accessories included: Turntable platter, dust cover, 2x dust cover hinges, balance counterweight, Phono RCA cable with grounding cable, AC power cord, rubber mat, instruction manual, Ortofon 2M Blue cartridge & headshell

TECHNICAL DATA
Turntable Section:
• Type of turntable: Direct drive, fully manual
• Drive: Quartz driven upper-torque direct drive with precision rotation
• Motor: DC Motor, 16-Pole, 3-Phase, brushless
• Rotation speeds: 33 1/3, 45 & 78 RPM
• Starting Torque: More than 4500 g/cm
• Start-up time / rpm change: Less than 0.3 sec.
• Wow and Flutter: Less than 0.1% WRMS (JIS WTD)
• S/N Ratio: More than 60dB (DIN-B)
• Breaking System: Electronic brake

Turntable Platter:
• Turntable Platter: Aluminium die-cast
• 305 mm diameter
• Weight About 2.1 kg

Tonearm Section:
• Type: Static balanced S-Shape
• Effective Length: 230 mm
• Overhang: 15 mm
• Tracking Error Angle: Less than 3 degrees
• VTA Adjustment Range: 0-6 mm
• Applicable Cartridge Weight: 17 – 25 g (incl. Headshell)
• Anti-Skating Range: 0-3 g
• Terminals: 1x PHONO Out (gold-plated), 1x GND Earth Terminal

Cartridge:
• Type of cartridge: Ortofon 2M Blue
• Output voltage at 1000 Hz, 5cm/sec.: 5.5 mV
• Channel balance at 1 kHz: 1.5 dB
• Channel separation at 1 kHz: 25 dB
• Channel separation at 15 kHz: 15 dB
• Frequency response: 20-20.000 Hz + 2 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force: 80 µm
• Compliance, dynamic, lateral: 20 µm/mN
• Stylus type: Elliptical
• Stylus tip radius: r/R 8/18 µm
• Tracking force range: 1.6-2.0 g (16-20 mN)
• Tracking force, recommended: 1.8 g (18 mN)
• Tracking angle: 20°
• Internal impedance, DC resistance: 1.3 kOhm
• Internal inductance: 700 mH
• Recommended load resistance: 47 kOhm
• Recommended load capacitance: 150-300 pF
• Cartridge colour, body/stylus: Black/Blue
• Cartridge weight: 7.2 g

General:
• Power Supply: AC IN 100~240V, 50/60 HZ
• Power consumption: 3W
• Dimensions: 460(W) x 367.3(D) x 172.6(H) mm
• Weight: 10.35 kg
• Incl.: dust cover + 2x hinge, rubber mat, power supply cable, RCA cable with grounding connection (gold-plated), Headshell with Ortofon 2M Blue (pre-installed), turntable platter, operation manual & counterweight

MANUAL HIFI-TURNTABLE

For decades, direct-drive turntables from Dual have been renowned for their quality and reliability. The rumble free direct-drive in the CS 618Q keeps the RPM totally stable, while operating without noise or vibration.

The advanced twin gimbal precision tonearm is partnerd with an Ortofon 2M Blue pickup.

The turntable comes with an auto-stop feature that includes an automatic tonearm lift to reduce wear and tear on the needle as it moves to the end of the record.

DETAILS:
Plinth: Solid MDF
• Surface Options: Vinyl veneer, Gloss paint, Walnut veneer
• Elastomer vibration absorber integrated inside the feet
• Removable dustcover

Platter: Aluminium Die-cast
• Heavy aluminium die-cast platter
• Heavy rubber mat for resonance damping
• Hardened steel spindle integrated into the direct-drive

Tonearm: Twin Gimbal Design
• Autostop function with an automatic tonearmlift
• Solid aluminium construction with precision pivot ball-bearing
• Adjustabel trackingforce and antiskating

Drive: Direct-drive
• Quartz stabilised, high end direct-drive
• No vibrations through coreless inductors
• Double shielded Rotormagnets to eliminate any stray magnetic fields

TECHNICAL DATA:
Drive:
• Drive: Direct-drive
• Speed settings: 33/45/78
• Wow & Flutter: < ±0,07 % (DIN WTD)

Tonearm:
• Auto-Start/-Stop-Function: Auto-Stop / Auto Tonarmlift
• Bearing: 4 x Pivot ball-bearing /twin gimbal mounting
• Effective length: 221,5 mm
• Offset Angle: 25,6°
• Overhang: 19 mm
• Type: statically balanced
• Stylus Pressure Range: 0 g to 4 g
• Cartridge Weight Range: 5 g to 9 g
• Factory installed pick up: Ortofon 2M Blue

Platter:
• Material: Aluminium die-cast
• Mat: Rubber 2,5 mm
• Bearing: Hardened steel spindle, Brass bushing
• Diameter: 305 mm
• Weight (incl. Mat): 1450 g

Plinth:
• Material: MDF, folded
• Surface finish: Vinyl veneer / Black
• Feet: Ø 62 mm / Elastomer
• Connection: RCA socket
• Connection to Phono Input: ✓
• Connection to Line Input: ✓
• Digital Output: ✕
• Dimension, closed dustcover: 435 x 367 x 145 mm
• Dimension, open dustcover: T: 415 mm / H: 400 mm
• Weight: 7 kg
• Power plug AC / DC: External power supply

Manual: https://hifi.dual.de/wp-content/uploads/2022/07/BDA-CS-618Q_manual_V6_DE_EN.pdf

FULLY AUTOMATIC PLUG & PLAY-TURNTABLE

The uncomplicated one from Dual with aspirations. The CS 329 uses sophisticated technology for entry-level analogue music playback.

With Plug & Play, you get a complete, ready-to-use package; all components are pre-assembled and permanently set. Plug in and get started!

As a fully automatic machine, the CS 329 offers ideal convenience. The tonearm swivels, lowers and raises autonomously at the touch of a button. All you have to do is put on the record and press the start button.

DETAILS:
Plinth: MDF - Plastic
• Elastomer vibration absorber integrated inside the feet
• Removable dust cover
Platter: Aluminium Die-cast
• Precise aluminium die-cast
• Heavy rubber mat for resonance damping
Tonearm: Straight, Plug and Play
• Plug & Play: all adjustments are factory fixed
• All functions can be fully automatic or manual
Drive: DC- Motor / Belt
• Rubber mountings for vibration decoupling
• Precision cut belt for lower wow & flutter

TECHNICAL SPECIFICATIONS:
Motor:
• Drive: Belt
• Speed settings: 33/45
• Wow & Flutter: < ±0,12 % (DIN WTD)

Tonearm:
• Auto-Start/-Stop-Function: Automatic
• Bearing: Ball-bearing
• Effective length: 221,5 mm
• Offset Angle: 25,6°
• Overhang: 19 mm
• Type: statically balanced
• Stylus Pressure Range: Fixed
• Cartridge Weight Range: N / A
• Factory installed pick up: Audio-Technica AT91

Platter:
• Material: Aluminium die-cast
• Mat: Rubber 2,5 mm
• Bearing: Hardened steel spindle Brass bushing (inverted)
• Diameter: 297 mm
• Weight (incl. Mat): 667 g

Plinth:
• Material: Plastic / MDF
• Surface finish: Black
• Feet: Ø 62 mm / Elastomer
• Connection: RCA cable (fixed)
• Connection to Phono Input: ✓
• Connection to Line Input: ✓
• Digital Output: ✕
• Dimension, closed dustcover: 435 x 372 x 132 mm
• Dimension, open dustcover: T: 405 mm / H: 390 mm
• Weight: 5 kg
• Power plug AC / DC: External power supply

Manual: https://hifi.dual.de/wp-content/uploads/2022/09/BDA-CS-329_manual_V1_DE_EN.pdf

STANTON STX
LIMITED EDITION PORTABLE SCRATCH TURNTABLE
RAZOR SHARP CUTS, RIGHT AWAY

The STX is the only portable turntable that comes with a factory-installed mini Innofader Nano crossfader. Designed to last over 4 million cycles, this buttery-smooth fader and can be easily swapped between left and right positions to accommodate both left-handed and right-handed scratch styles. The independent crossfader Cut-In and Curve knobs deliver an unrivaled level of crossfader customization, allowing DJs to precisely calibrate the crossfader to suit their own style. This level of customization, along with the ultra-stable platter and tonearm, makes it easy to achieve the absolute cleanest cuts possible.

SCRATCH WHENEVER, WHEREVER
Second only to a sharp, ultra-precise crossfader, ease of portability is vital for a portablism-focused turntable. High-quality rechargeable Lithium-ion batteries are included with the STX, providing enough portable power for hours of mobile use.
The batteries can easily be charged by connecting the unit to a computer or wall charger using the USB-C input. For extended scratch sessions, the USB-C input can also be used with external power sources for even more cutting time.
To top everything off (literally), the latching lid also functions as a stackable, latching base, to bring the STX to standard turntable height.

WELL-CONNECTED FOR CREATORS
Performing with beats and loopers is as simple as connecting a smartphone wirelessly with Bluetooth or with the 1/8” stereo input. The USB port with one-touch recording makes it fast and easy to record high-quality session audio for social media content creation, while the stereo RCA outputs allow you to connect external mixers and speakers for live performances.

PERFORMANCE READY
The modification culture is alive and well in the portablism world. Since the inception of this art form, we’ve seen ingenious designs and customizations. The most popular and utilitarian mods are already included on the STX, including a Start/Stop button, an on-board speaker, and a pitch slider with Ultra-Pitch selection switch. These key features allow for inspiring performances right out of the box and provide a solid foundation upon which DJs can further customize to match their own unique portablist style.

Technical Specifications
Connections (1) RCA line-level output (stereo pair)
(1) 1/4” (6.35 mm) stereo headphone output
(1) 1/8” (3.5 mm) stereo headphone output
(1) 1/8” (3.5 mm) stereo input
(1) USB-C port (charges the internal battery)
(1) USB-A port (USB flash drive recordings

Speeds 33 1/3, 45, 78 RPM (45 RPM adapter included)

Power (2) 3.7V Li-ion batteries

Dimensions
(width x depth x height)
13.0” x 13.0” x 4.0” (3.25” without cover attached)
330.2 x 330.2 x 101.6 mm (82.6 mm without cover attached)

Weight 5.3 lbs.
2.4 kg

The THORENS TD 204 was developed for the audiophile beginner. A turntable with sound expansion potential for audiophiles.
The surface finishes "black high gloss" and "walnut high gloss" fit seamlessly into the existing range with the typical THORENS design. The brand identity is underlined by the high processing quality and guarantees a long life like all Thorens turntables.

The newly developed TP 120 tonearm impresses with its high-quality bearing technology. The bearing play and the coefficients of friction could be reduced to an astonishingly low level for the price class by using modern bearings. The TP 120 is a real 9" J-shaped aluminum tonearm with an effective tonearm mass of 15 grams. The visual similarity to the larger models TP 150 and TP 124 is obvious and promises first-class properties.

The detachable headshell with SME connector is equipped with an AT95E from the Japanese pickup specialist Audio Technica. The skating compensation is carried out via a spring.

The connection terminal on the back shows high-quality RCA sockets for a solid connection to the amplifier. An integrated MM phono pre (which can be switched on/off) enables direct connection to a high-level input.

The platter, which is precisely manufactured from die-cast aluminum, is set in rotation by a precision drive belt. The plinth of the TD 204 rests on four vibration-damping feet.

SPECIAL FEATURES:
• Smooth running belt drive
• Thorens TP 120 9” tonearm with J shape
• Detachable headshell with SME connector
• Switchable MM phono preamplifier
• Die-cast aluminum platter
• Pre-installed Audio Technics AT95E cartridge

PREMIUM BELT DRIVE USB TURNTABLE SYSTEM

HIGHLIGHTS:
Belt-driven HiFi turntable with Ortofon 2M Red
20 mm acrylic platter with LED lighting
Decentralised drive motor with external belt guide

SOUND MEETS DESIGN
The Turn 7 bridges the gap between high-end HiFi turntables and uncompromising design. The belt-driven turntable meets the exacting demands of audiophile music fans thanks to precisely manufactured components. The acrylic platter with LED lighting and the external drive belt make the Turn 7 an absolute eye-catcher.

POWERFUL AND STEADY DRIVE
A decentralised, low-vibration DC motor drives the Turn 7. The integral flat belt runs gracefully along the turntable exterior, ensuring smooth operation and a sophisticated appearance. The start/stop rotary switch allows you to select between the turntable's two speeds (33 and 45 RPM).

HEART OF ACRYLIC: THE TURNTABLE PLATTER
The acrylic platter is 20 mm thick, weighs 1.7 kg, and has outstanding evenness thanks to precision manufacturing. It also has excellent antistatic characteristics. As a result, crystal-clear audio is possible without using a platter mat. The satin finish of the material creates a focal point and contrasts with the otherwise plain design of the belt-driven turntable.

LET THERE BE LIGHT – LEDS INSIDE
One of the unique features of the Turn 7 is the optional, blue platter illumination. Inconspicuously placed beneath the platter, multiple LEDs with a diffuser cover sets the mood and creates a warm and inviting ambience.

TOP-CLASS TONE ARM
The high-quality carbon tone arm has exceptional acoustic properties. The turntable's authentic sound is brought out to its full potential by effectively cancelling out vibrations. The ability to adjust the height (vertical tracking angle – VTA) and an anti-skating adjustment ensure maximum precision.

ORTOFON 2M RED PRE-INSTALLED
The turntable comes with the Ortofon 2M Red cartridge system pre-installed. The Ortofon 2M Red has an elliptical stylus tip and excellent sonic characteristics, including first-rate sound accuracy and reproduction. The Ortofon 2M Red is a highly versatile cartridge system with an open, dynamic sound and warm tones. The universal headshell connection (SME) adds more options for cartridge systems.

METICULOUSLY PERFECTED
In addition to its high-quality preamplifier, the Turn 7 also features versatile switching between line and phono signals. The gold-plated corrosion-resistant RCA connectors ensure the best possible signal transmission. The built-in USB output allows you to digitise vinyl records.

SIMPLE DESIGN & PURE FUNCTIONALITY
The sturdy MDF wooden plinth and height-adjustable isolator feet with aluminium surround provide effective decoupling for the turntable. The high-gloss piano lacquer is a classy contrast to the timeless minimalism while emphasising the Turn 7's superior quality.

FEATURES:
• Premium belt-driven HiFi turntable
• Decentralised DC motor with external drive belt on the acrylic platter
• Fully manual operation with motor control switch for switching between speeds (33/45 RPM)
• Precision-machined, 20 mm thick solid acrylic platter (1.7 kg) with outstanding levelling and electrostatic properties for a crystal-clear sound
• Indirect blue LED lighting on the acrylic platter (can be switched on/off)
• Audiophile carbon tonearm with height adjustment (VTA) and anti-skating adjustment
• Pre-installed Ortofon 2M Red cartridge for optimised sound reproduction and fidelity
• Universal headshell connection (SME) for additional flexibility
• USB recording function: Recording and digitisation of vinyl via the simply USB connection for PC/Mac
• High-quality integrated preamp (switchable phono/line output)
• Gold-plated, corrosion-resistant audio connections (removable power and RCA cable)
• Height-adjustable, shockproof aluminium feet for effective decoupling
• Solid MDF plinth with piano finish and a timeless design
• Incl.: dust cover, 2x hinges, felt mat, international power supply (UK/EU/US), RCA cable, headshell with Ortofon 2M Red (pre-installed), 7" aluminium adapter, acrylic turntable platter, allen key, USB-cable, instruction manual & counterweight

TECHNICAL SPECIFICATIONS:
Turntable Section:
• Type of turntable: Belt-Driven manual Turntable System with USB Interface
• Drive: Belt drive
• Motor: DC Motor
• Rotation speeds: 33 1/3, 45
• Starting Torque: //
• Start-up time / rpm change: //
• Wow and Flutter: 0,2% WRMS
• S/N Ratio: >45dB or higher
• Breaking System: Manually
Turntable Platter:
• Turntable Platter: Acrylic glass
• Diameter: 300 mm
• Weight: 1.7 kg
Tonearm Section:
• Type: Straight Tonearm
• Effective Length: 223.6 mm
• Overhang: 18.61 mm
• Tracking Error Angle: ±1.5°
• VTA Adjustment Range: - 2 ~ 4 mm
• Applicable Cartridge Weight: 7.2 ~ 11.2 g (incl. Headshell)
• Anti-Skating Range: 0 - 4 mm
• Terminals: 1x PHONO/LINE Out
Cartridge:
• Ortofon 2M Red
• Output voltage at 1000 Hz, 5cm/sec.: 5.5 mV
• Channel balance at 1 kHz: 1.5 dB
• Channel separation at 1 kHz: 22 dB
• Channel separation at 15 kHz: 15 dB
• Frequency response: 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force: 70 µ Mm
• Compliance, dynamic, lateral: 20 µ Mm
• Stylus type: Elliptical
• Stylus tip radius: r/R 8/18 µm
• Tracking force range: 1.6-2.0 g (16-20 mN)
• Tracking force, recommended: 1.8 g (18 mN)
• Tracking angle: 24.7°
• Internal impedance, DC resistance: 1.3 kOhm
• Internal inductance: 700 mH
• Recommended load resistance: 47 kOhm
• Recommended load capacitance: 150-300 pF
• Cartridge colour, body/stylus: Black/Red
• Cartridge weight: 7.2 g
General:
• Power Supply: 12V, 1A DC
• Power consumption: 12W
• Dimensions: 420(W) x 356(D) x 148(H) mm
• Weight: 8.2 kg

Jesse Dean Face Plate for your Stanton STX portable turntable.

Swap out your stock or JDDX2R-SX face plate with one of these!

Available colours:

Black
Blue
Red
White

After the Debut Carbon EVO revolutionized the Debut series in 2020, the Debut PRO raises the bar even higher.

A MILESTONE FOR THE NEXT DECADES
The Debut PRO brings an absolutely new design to Pro-Ject turntables. The audiophile turntable is convincing in all respects – not only visually, but more importantly also in terms of sound.
The precision CNC milled parts are optically perfectly coordinated and lead the Debut PRO to its modern simple, elegant and unprecedented design. The nickel finish of all these aluminium components result in a hard, resistant surface. This process enables us to produce very high-quality and sustainable components and avoid plastics and similar materials that continue to age over time and would more importantly also degrade sound quality.

The tonearm bearing is a completely new design. Precision CNC'd out of a single block of aluminium, you can see all the production stages above. The last step is putting a nickel finish on it. This will increase the rigidity of the bearing, ensuring free and fluid movement of the tonearm and precise tracking without material degration in looks or function.

DEEPLY DRIVEN
The electronically regulated synchronous motor drives the platter and guarantees the most accurate and stable speeds. Change between them easily with the toggle switch. With the supplied round belt for 78 rpm you can also listen to your shellac records.

A NEW PLATTER – A DEEPPER DISH
The new Debut PRO platter is a first on any Pro-Ject turntable. It features a notch for the record label and together with our Record Puck PRO (available separately) the puck's weight will press your record tightly against the platter. The die-cast aluminium platter is reworked and precision balanced in an extra step to obtain an evenly spinning platter. It is anti-magnetic, allowing MC cartridges to work properly. Delve deep into the vast upgrade path the Debut PRO has to offer!
The anti-magnetic heavy aluminium platter has a ring made of TPE (thermoplastic elastomer) on the inside that helps to dampen all resonances and minimizes wow and flutter. Our seperately available Record Puck PRO provides an extra level of damping and stability, so it is the perfect add-on for the Debut PRO.

HYBRID TONEARM
The new Debut PRO features a one-piece carbon-aluminium sandwich tonearm. The carbon layer gives the tonearm a high degree of rigidity, while the inner aluminium tube takes over the damping of the tonearm. This makes the tonearm perfect to be upgraded with higher-end MC cartridges!

AZIMUTH & VTA ADJUSTMENT
The newly designed tonearm base allows you to adjust both the azimuth and the vertical tracking angle (VTA). The tonearm height can be continuously adjusted by loosening the two grub screws. These settings give you the option of adapting the tonearm to height changes allowing the use of different turntable mats or other cartridges to always achieve the best sound quality. Setting and experimenting with the VTA & Azimuth is crucial in extracting every last bit of performance out of your cartridges.

Features:
Pick it PRO
Lively and robust sound
The perfect combination of components is the key to achieve the great sound of the Pick it PRO.

Nickel Coating
Sustainable components
The nickel finish of the aluminium components results in a hard, resistant surface.

Hybrid Tonearm
Carbon Aluminium Sandwich
This super stiff and uniquely dampened tonearm ensures perfect tracking of the record groove.

VTA & Azimuth
Fully adjustable
The Debut PRO comes with fully adjustable Azimuth & VTA. It offers you the possibility to modify your turntable as you want it.

33/45/78 RPM
High precision motor control
The playback speeds are electronically controlled with precision, which guarantees the most accurate and stable music reproduction. Change between speeds easily with the toggle switch.

Bearing block
Complete new design
The precision CNC milled and nickel coated tonearm bearing parts are completely new and designed just for the PRO.

Special Platter
TPE damped & anti magnetic
The heavy aluminium platter has a ring made of TPE (thermoplastic elastomer) on the inside that helps to dampen all resonances and minimizes wow and flutter.

Metal Feet
Damped & height adjustable
The three height adjustable damped aluminium feet guarantee the perfect stand & massively reduce risk of acoustical feedback.

Technical Specifications:
• Speed: 33, 45/(78) (electronic speed change)
• Drive principle: belt drive with electronic speed control
• Platter: 300mm, die cast aluminium platter with TPE damping and felt mat
• Platter bearing: high precision stainless steel axle in bronze bushing
• Wow & flutter: 33: +/-0,16%; 45: +/-0,14%
• Speed drift: 33: +/-0,40%; 45: +/-0,50%
• Signal to noise: 68dB
• Tonearm: 8,6” one-piece carbon-aluminium tonearm
• Effective arm length/mass: 218,5 mm / 10,0 g
• Overhang: 18,5mm
• Included accessories: 15V DC / 0,8A power supply, dust cover, 78 RPM round belt, 7‘‘ single adapter
• Power consumption: 4W / 0W standby
• Dimensions: 415 x 113 x 320mm (WxHxD)
• Weight: 6 kg net

Manual: https://www.project-audio.com/wp-content/uploads/2021/07/PJ-Phono-DebutPro-Manual.pdf

Jesse Dean Face Plate for your Stanton STX portable turntable.

Swap out your stock or JDDX2R-SX face plate with one of these!

Available colours:

Black
Blue
Red
White

The revolutionary concept combines the highest quality of music playback with a design that has won several awards worldwide – including the German Design Award and ‘Best Turntable’ award from ‘What Hi-Fi? Sound and Vision’ magazine. With the concept, to find an affordable entry point to the high-end world is a breeze. It reveals the magic of optimum sound reproduction even for those music lovers who could not previously afford this experience. You can buy the concept in a package with specially developed moving magnet (MM) or moving coil (MC) cartridges. A frictionless magnetic bearing tonearm is responsible for the optimal performance of the cartridges. All critical parameters from cartridge tracking weight to anti-skating are preadjusted in our factory. The concept represents the ideal of stress-free ‘plug and play’: unpack, connect, put the record on the platter – and just enjoy music. There was never more audiophile technology in this class of turntables.

The concept achieves these highest of requirements, realising the Clearaudio vision.

Beneath the sleek, contemporary exterior is a level of technical sophistication unique to Clearaudio.

The concept‘s body is carefully crafted from medium-density wood fibre (or, optionally, pressure-formed solid wood) with a selection of smart made-to-match surface finishes. The body’s upper layer incorporates a special high-tech satined plastic compound designed to minimise unwanted resonance.

The DC motor is fed by an external voltage-stabilised power supply and is completely decoupled from the chassis, isolating the record from any mechanical interference.

The concept tonearm features a magnetic bearing that is friction-free for extremely low distortion and superb performance. The package is completed with the high-quality Clearaudio CONCEPT MM or Clearaudio CONCEPT MC cartridge (toneam and/or cartridge upgrade possible).

With the concept turntable package, Clearaudio offers you an extremely innovative design that is very affordable.

Concept black turntable including concept tonearm and concept MM cartridge.
Upgrade for cartridge/tonearm possible.
(Delivery without dustcover)

FEATURES
Technical Specifications:
• CONSTRUCTION DETAILS: Resonance-optimised turntable; chassis comprises medium-density wood fibre (silver / black) or pressure-formed solid wood (wood / dark wood); upper layer incorporates high-tech satined plastic compound.
• SPEED OPTIONS: 33 ⅓, 45, 78rpm
• DRIVE UNIT: Decoupled and resonance damped 12V DC motor, flat belt-drive and plug-in power supply unit designed for worldwide use with all networks and power frequencies.
• BEARING: Polished and tempered steel spindle in a sintered bronze housing, running on a teflon thrust-pad.
• PLATTER: 30mm / 1.18 inch main platter, made out of synthetic material with high-density and excellent dimension / precision CNC machined surface aluminium sub platter
• SPEED ACCURACY (MEASURED): ± 0.05%
• POWER CONSUMPTION: Max. consumption: 2.5 watts / Consumption in operation: 0.5 watts / Off mode: 0.0 watts
• TOTAL WEIGHT: Approx. 7.5kg (incl. tonearm and cartridge)
• DIMENSIONS (W/D/H): Approx. 16.54 × 13.78 × 4.92 inches (with tonearm) / Approx. 420 × 350 × 125mm (with tonearm)
• MANUFACTURER’S WARRANTY: 2 years*
* Provided the warranty card is fully completed and returned to Clearaudio within 2 weeks of purchase.

Manual: https://clearaudio.de/_assets/_pdf/manuals/turntables/CA_Concept_E+D.pdf?d=1667911999

The revolutionary concept combines the highest quality of music playback with a design that has won several awards worldwide – including the German Design Award and ‘Best Turntable’ award from ‘What Hi-Fi? Sound and Vision’ magazine. With the concept, to find an affordable entry point to the high-end world is a breeze. It reveals the magic of optimum sound reproduction even for those music lovers who could not previously afford this experience. You can buy the concept in a package with specially developed moving magnet (MM) or moving coil (MC) cartridges. A frictionless magnetic bearing tonearm is responsible for the optimal performance of the cartridges. All critical parameters from cartridge tracking weight to anti-skating are preadjusted in our factory. The concept represents the ideal of stress-free ‘plug and play’: unpack, connect, put the record on the platter – and just enjoy music. There was never more audiophile technology in this class of turntables.

The concept achieves these highest of requirements, realising the Clearaudio vision.

Beneath the sleek, contemporary exterior is a level of technical sophistication unique to Clearaudio.

The concept‘s body is carefully crafted from medium-density wood fibre (or, optionally, pressure-formed solid wood) with a selection of smart made-to-match surface finishes. The body’s upper layer incorporates a special high-tech satined plastic compound designed to minimise unwanted resonance.

The DC motor is fed by an external voltage-stabilised power supply and is completely decoupled from the chassis, isolating the record from any mechanical interference.

The concept tonearm features a magnetic bearing that is friction-free for extremely low distortion and superb performance. The package is completed with the high-quality Clearaudio CONCEPT MM or Clearaudio CONCEPT MC cartridge (toneam and/or cartridge upgrade possible).

With the concept turntable package, Clearaudio offers you an extremely innovative design that is very affordable.

Concept black/silver turntable including concept tonearm and concept MM cartridge.
Upgrade for cartridge/tonearm possible.
(Delivery without dustcover)

FEATURES
Technical Specifications:
• CONSTRUCTION DETAILS: Resonance-optimised turntable; chassis comprises medium-density wood fibre (silver / black) or pressure-formed solid wood (wood / dark wood); upper layer incorporates high-tech satined plastic compound.
• SPEED OPTIONS: 33 ⅓, 45, 78rpm
• DRIVE UNIT: Decoupled and resonance damped 12V DC motor, flat belt-drive and plug-in power supply unit designed for worldwide use with all networks and power frequencies.
• BEARING: Polished and tempered steel spindle in a sintered bronze housing, running on a teflon thrust-pad.
• PLATTER: 30mm / 1.18 inch main platter, made out of synthetic material with high-density and excellent dimension / precision CNC machined surface aluminium sub platter
• SPEED ACCURACY (MEASURED): ± 0.05%
• POWER CONSUMPTION: Max. consumption: 2.5 watts / Consumption in operation: 0.5 watts / Off mode: 0.0 watts
• TOTAL WEIGHT: Approx. 7.5kg (incl. tonearm and cartridge)
• DIMENSIONS (W/D/H): Approx. 16.54 × 13.78 × 4.92 inches (with tonearm) / Approx. 420 × 350 × 125mm (with tonearm)
• MANUFACTURER’S WARRANTY: 2 years*
* Provided the warranty card is fully completed and returned to Clearaudio within 2 weeks of purchase.

Manual: https://clearaudio.de/_assets/_pdf/manuals/turntables/CA_Concept_E+D.pdf?d=1667911999

Record clamp.
LP-clamping unit with resonance absorbing locking unit and stainless steel grip.
Weight: 190 g

Record clamp.
The ergonomic form of this record clamp is precision machined from aluminium, black anodized and finished with a silver rim. On the underside is a Teflon insert that locates over the spindle for frictionless positioning.
Weight: 215 g

An easy to use tool that quickly corrects undersized spindle holes – fitted with an ergonomic aluminum handle.
Diameter (Ø): 7.3 mm

Flat belt
Drive belt for concept, concept active, Performance DC and Ovation.
Dimension: 160 × 4 × 0,8 mm

Jesse Dean Corner Pads for your Stanton STX portable turntable.

Swap out your stock blue corner pads!

4mm silicone pads with adhesive back
Durable finish
Pack of 8, for top and bottoms
Colours availabe
Black
Grey
White

Jesse Dean Corner Pads for your Stanton STX portable turntable.

Swap out your stock blue corner pads!

4mm silicone pads with adhesive back
Durable finish
Pack of 8, for top and bottoms
Colours availabe
Black
Grey
White

Jesse Dean Decal Kit for your Stanton STX portable turntable.

Swap out or cover your stock blue decals!

Available colours:

Black
Red
White

Jesse Dean Decal Kit for your Stanton STX portable turntable.

Swap out or cover your stock blue decals!

Available colours:

Black
Red
White

Omni Portable Turntable Tone Arm Tension Mod by Tiny Steppa

Enhance Durability. Unleash Potential.

"The tone arm tension design in the Omni is actually very simple, with the two rubber bands doing their job well. However, we're aware that rubber bands can become hard and lose elasticity over time, much like changing a platter belt after a long while. This modification gives you an option to enhance durability, and elevate Omni's potential."

Easy stylus weight adjustment: Fine-tune the stylus weight with your fingertips.
Tone arm protection: Nylon screws prevent tonearm coating damage during setup.
Simple installation: Quick and user-friendly assembly.
Tool kit included: All necessary tools are in the package.
Omni certified: Meets quality and compatibility standards.

Installation video can be found here:
https://www.youtube.com/watch?v=ctHskU8k67c

Watch the adjustment video here:
https://www.youtube.com/watch?v=TDKhq1hTC3s

Premium Class Direct Drive Turntable System SL-1500C

The Latest Coreless Direct Drive Motor Achieves High-precision Stable Rotation
The technologies acquired through the development of the SL-1200 Series and the high-end SL-1000R model were lavishly inserted into the motor drive unit, a key part of the turntable. The motor exclusively tunes the single-rotor, coreless direct drive motor adopted by the SL-1200GR in order to read the high rotation accuracy and high-precision signals of the record. Optimal motor control is conducted for the inertial mass of the two-layer structure platter on which the vinyl record is placed with deadening rubber on the entire back surface to eliminate unwanted resonance in the aluminium die-cast platter to eliminate the rotation irregularity called cogging. The aluminium die-cast chassis is rigidly integrated with a special material consisting of ABS mixed with glass fiber to achieve a two-layer construction. The insulator is comprised of a spring and rubber to provide optimal vibration-damping characteristics. The tonearm is a static-balance universal S-shape tonearm, another Technics tradition. By adopting a high-precision bearing using the same gimbal suspension construction and machined housing as the SL-1200 Series, high initial sensitivity is achieved. In addition, reliability has been improved by incorporating a removable power cable and gold-plated terminals, which have less sound quality degradation, for the PHONO and LINE terminals.

Complete Turntable with a Built-in Phono Equalizer and Cartridge
Complete Turntable with a Built-in Phono Equalizer and Cartridge In order to enjoy playing analogue records more comfortably, the SL-1500C features a built-in phono equalizer and bundled cartridge. There is no need to separately prepare either one, making it easy to link with a wide range of audio equipment. The shield structure of the built-in phono equalizer suppresses the effects of external noise and noise from the power supply. It is also equipped with a switch to turn the LINE output off when it is not being used. The turntable has been designed to thoroughly shut-out adverse effects to the PHONO output. The dedicated power supply for the PHONO output terminal is isolated from the power supply for the LINE output terminal, and has been designed to prioritize sound quality by minimising the wiring of the PHONO signal. The isolated terminals also prevent wiring mistakes. An Ortofon 2M RED cartridge, which is highly acclaimed as an MM cartridge, has been selected for the bundled cartridge. Combining this high-quality cartridge with the performance of the SL-1500C will maximise the sound quality of vinyl records.

Equipped with an Auto Lifter Function That Allows You to Enjoy Playing Records More Comfortably
When the tonearm reaches the end of the record, the Auto Lifter function automatically raises the cartridge. This prevents unnecessary wear on your valuable vinyl records and stylus. By embedding the Auto Lifter function in the base portion of the tonearm, it eliminates impacts to the tonearm. Due to a simple design that doesn’t use motor power, there is no electrical or vibrational impact and it will not prevent the movement of the tonearm. In response to requests from many users regarding the Auto Lifter function, a design that prioritises sound quality was adopted. The functions required to playback records were kept to a bare minimum, achieving simple and easy-to-use operability.

Simple Design with Functional Beauty
The SL-1500C sports a simple design without unnecessary frills, while retaining the superb operating feel that is a Technics tradition. The attractive appearance lets you enjoy playing records to your heart’s content.

Specs:
• The Latest Coreless Direct Drive Motor Achieves High-precision Stable Rotation
• Complete Turntable with a Built-in Phono Equalizer and Cartridge
• Equipped with an Auto Lifter Function That Allows You to Enjoy Playing Records More Comfortably
• Simple Design with Functional Beauty

Technical Data:
Turntable section:
• Type: Direct Drive Manual Turntable
• Turntable Speeds: 33-1/3, 45 and 78 r/min
• Starting Torque: 0.18 N・m / 1.8 kg･cm
• Build-up Characteristics: 0.7 s. from standstill to 33 1/3 rpm
• Wow And Flutter: 0.025 % W.R.M.S.
• Turntable Platter:
- Aluminium diecast
- Diameter : 332 mm
- Weight : Approx. 2.0 kg (Including rubber sheet)

Tonearm Section:
• Type: Universal Static Balance
• Effective Length: 230 mm
• Overhang: 15 mm
• Tracking Error Angle:
- Within 2° 32'　(at the outer groove of 30 cm (12") record)
- Within 0° 32'　(at the inner groove of 30 cm (12") record)
• Applicable Cartridge Weight Range:
(without auxiliary weight):
- 5.6 - 12.0 g
- 14.3 - 20.7 g (including head shell)
(with auxiliary weight):
- 10.0 - 16.4 g
- 18.7 - 25.1 g (including head shell)
• Head Shell Terminal Lug: 1.2 mmφ 4-pin terminal lug

Terminals:
• Audio Output:
- PHONO (Pin Jack) x 1
- EARTH TERMINAL x 1
- LINE (Pin Jack) x 1

General:
• Power Supply: AC 110 - 240 V, 50 / 60 Hz
• Power Consumption:
- 8 W
- Approx. 0.2W (Standby)
• Dimensions (W x H x D): 453 x 169 x 372 mm
• Weight: Approx. 9.9 kg
• Accessories: Turntable, Turntable sheet, Dust cover, EP record adaptor, Balance weight, Auxiliary weight, Head shell, Cartridge(ortofon 2M Red), PHONO cable, PHONO earth lead, AC power supply cord, Owner's Manual

Ortofon Record stabilizer - Black - 240 g

The Ortofon Record Stabilizer is offered in two versions: Standard and Heavy, meticulously designed to seamlessly complement a variety of turntables. Completely reengineered, these stabilizers boast an elegant aesthetic and user-friendly functionality. No preparations are needed; simply place the stabilizer on the record before playback to experience improved playback with reduced vibration.

Crafted with precision, the Ortofon Record Stabilizer comes in a premium satin matte anodized finish, available in Silver or Black, featuring the distinctive Ortofon textured wave-grip. The Standard version is ideal for entry-level and sub-chassis turntables, made from aluminum with a smooth felt underside.

Enhance your vinyl listening experience effortlessly with the Ortofon Record Stabilizer, where form meets function for optimal sound performance.

Quartz controlled 300 Hz light source

Enables exact adjustment of your turntable speed by keeping the light source independent from fluctuations in the mains frequency and voltage, which would otherwise give distorted results. A quartz oscillator generates an accurate 300 Hz, white light source, making precise speed adjustment easy when used in conjunction with the Clearaudio Stroboscopic Testrecord.

An optimal listening experience requires precise settings, especially when it comes to motor speed. The clearaudio Speed Light V2 is your key to accurate speed adjustments, regardless of the power grid frequency in your country. In this enhanced version, we present an upgrade for ultimate precision and user-friendliness.

New features at a glance:

White LED for improved visibility:
The transition from a blue LED to a white LED ensures an even better visibility of the line pattern on the stroboscopic disc. Every pulse is accurately captured, allowing for precise speed adjustments.

Extended operating time with a new battery:
The switch to the lithium button cell (CR2023) not only provides a longer operating time but also ensures a constant power supply for reliable performance. The Speed Light V2 does not have a rechargeable battery and operates only on a battery or continuous power.

New Micro-USB port for battery-independent operation:
The implementation of a Micro-USB port offers the option of battery-independent operation.

Aluminum casing:
The casing, milled from solid material and made of anodized aluminum, replaces the previous plastic, improving durability and adding an aesthetically pleasing element.

Compatible with the Stroboscopic Test Record:
The clearaudio Speed Light V2 is perfectly tuned for use with our Stroboscopic Test Record.

Manual: https://www.clearaudio.de/_assets/_pdf/manuals/accessories/CA_Speed%20light%20V2_E+D.pdf

Providing unbeatable accuracy! The Stroboscope Testrecord together with the Speed Light V2 give the best results in adjusting your turntable speed.

Enables exact adjustment of your turntable speed by keeping the light source independent from fluctuations in the mains frequency and voltage, which would otherwise give distorted results. A quartz oscillator generates an accurate 300 Hz, white light source, making precise speed adjustment easy when used in conjunction with the Clearaudio Stroboscopic Testrecord.

An optimal listening experience requires precise settings, especially when it comes to motor speed. The clearaudio Speed Light V2 is your key to accurate speed adjustments, regardless of the power grid frequency in your country. In this enhanced version, we present an upgrade for ultimate precision and user-friendliness.

New features at a glance:

White LED for improved visibility:
The transition from a blue LED to a white LED ensures an even better visibility of the line pattern on the stroboscopic disc. Every pulse is accurately captured, allowing for precise speed adjustments.

Extended operating time with a new battery:
The switch to the lithium button cell (CR2023) not only provides a longer operating time but also ensures a constant power supply for reliable performance. The Speed Light V2 does not have a rechargeable battery and operates only on a battery or continuous power.

New Micro-USB port for battery-independent operation:
The implementation of a Micro-USB port offers the option of battery-independent operation.

Aluminum casing:
The casing, milled from solid material and made of anodized aluminum, replaces the previous plastic, improving durability and adding an aesthetically pleasing element.

Manual: https://www.clearaudio.de/_assets/_pdf/manuals/accessories/CA_Stroboscope%20Testrecord%20+%20Speedlight_E+D.pdf

Premium Class Direct Drive Turntable System SL-1500C

The Latest Coreless Direct Drive Motor Achieves High-precision Stable Rotation
The technologies acquired through the development of the SL-1200 Series and the high-end SL-1000R model were lavishly inserted into the motor drive unit, a key part of the turntable. The motor exclusively tunes the single-rotor, coreless direct drive motor adopted by the SL-1200GR in order to read the high rotation accuracy and high-precision signals of the record. Optimal motor control is conducted for the inertial mass of the two-layer structure platter on which the vinyl record is placed with deadening rubber on the entire back surface to eliminate unwanted resonance in the aluminium die-cast platter to eliminate the rotation irregularity called cogging. The aluminium die-cast chassis is rigidly integrated with a special material consisting of ABS mixed with glass fiber to achieve a two-layer construction. The insulator is comprised of a spring and rubber to provide optimal vibration-damping characteristics. The tonearm is a static-balance universal S-shape tonearm, another Technics tradition. By adopting a high-precision bearing using the same gimbal suspension construction and machined housing as the SL-1200 Series, high initial sensitivity is achieved. In addition, reliability has been improved by incorporating a removable power cable and gold-plated terminals, which have less sound quality degradation, for the PHONO and LINE terminals.

Complete Turntable with a Built-in Phono Equalizer and Cartridge
Complete Turntable with a Built-in Phono Equalizer and Cartridge In order to enjoy playing analogue records more comfortably, the SL-1500C features a built-in phono equalizer and bundled cartridge. There is no need to separately prepare either one, making it easy to link with a wide range of audio equipment. The shield structure of the built-in phono equalizer suppresses the effects of external noise and noise from the power supply. It is also equipped with a switch to turn the LINE output off when it is not being used. The turntable has been designed to thoroughly shut-out adverse effects to the PHONO output. The dedicated power supply for the PHONO output terminal is isolated from the power supply for the LINE output terminal, and has been designed to prioritize sound quality by minimising the wiring of the PHONO signal. The isolated terminals also prevent wiring mistakes. An Ortofon 2M RED cartridge, which is highly acclaimed as an MM cartridge, has been selected for the bundled cartridge. Combining this high-quality cartridge with the performance of the SL-1500C will maximise the sound quality of vinyl records.

Equipped with an Auto Lifter Function That Allows You to Enjoy Playing Records More Comfortably
When the tonearm reaches the end of the record, the Auto Lifter function automatically raises the cartridge. This prevents unnecessary wear on your valuable vinyl records and stylus. By embedding the Auto Lifter function in the base portion of the tonearm, it eliminates impacts to the tonearm. Due to a simple design that doesn’t use motor power, there is no electrical or vibrational impact and it will not prevent the movement of the tonearm. In response to requests from many users regarding the Auto Lifter function, a design that prioritises sound quality was adopted. The functions required to playback records were kept to a bare minimum, achieving simple and easy-to-use operability.

Simple Design with Functional Beauty
The SL-1500C sports a simple design without unnecessary frills, while retaining the superb operating feel that is a Technics tradition. The attractive appearance lets you enjoy playing records to your heart’s content.

Specs:
• The Latest Coreless Direct Drive Motor Achieves High-precision Stable Rotation
• Complete Turntable with a Built-in Phono Equalizer and Cartridge
• Equipped with an Auto Lifter Function That Allows You to Enjoy Playing Records More Comfortably
• Simple Design with Functional Beauty

Technical Data:
Turntable section:
• Type: Direct Drive Manual Turntable
• Turntable Speeds: 33-1/3, 45 and 78 r/min
• Starting Torque: 0.18 N・m / 1.8 kg･cm
• Build-up Characteristics: 0.7 s. from standstill to 33 1/3 rpm
• Wow And Flutter: 0.025 % W.R.M.S.
• Turntable Platter:
- Aluminium diecast
- Diameter : 332 mm
- Weight : Approx. 2.0 kg (Including rubber sheet)

Tonearm Section:
• Type: Universal Static Balance
• Effective Length: 230 mm
• Overhang: 15 mm
• Tracking Error Angle:
- Within 2° 32'　(at the outer groove of 30 cm (12") record)
- Within 0° 32'　(at the inner groove of 30 cm (12") record)
• Applicable Cartridge Weight Range:
(without auxiliary weight):
- 5.6 - 12.0 g
- 14.3 - 20.7 g (including head shell)
(with auxiliary weight):
- 10.0 - 16.4 g
- 18.7 - 25.1 g (including head shell)
• Head Shell Terminal Lug: 1.2 mmφ 4-pin terminal lug

Terminals:
• Audio Output:
- PHONO (Pin Jack) x 1
- EARTH TERMINAL x 1
- LINE (Pin Jack) x 1

General:
• Power Supply: AC 110 - 240 V, 50 / 60 Hz
• Power Consumption:
- 8 W
- Approx. 0.2W (Standby)
• Dimensions (W x H x D): 453 x 169 x 372 mm
• Weight: Approx. 9.9 kg
• Accessories: Turntable, Turntable sheet, Dust cover, EP record adaptor, Balance weight, Auxiliary weight, Head shell, Cartridge(ortofon 2M Red), PHONO cable, PHONO earth lead, AC power supply cord, Owner's Manual

• Crafted from high quality materials and components
• Pre-mounted Ortofon OM5E Cartridge
• Pre-mounted Bluetooth 5.0 Module

Timeless Design
The Transparent Turntable is a reinvention of a classic vinyl record player, designed for a modern home and an ever evolving technology. The Transparent Turntable is meticulously crafted out of aluminium and tempered glass. It is a belt driven system with a built in phono stage, and a pre-mounted cartridge from Danish Ortofon.

• Cartridge: Ortofon OM5E (MM)
• Stylus: Elliptical Diamond

Modular
Just like all Transparent products the TT has a completely modular design. With the future in mind, it is made for flexibility, upgradability and repairability.

• Cartridge Mount: Standard ½ in
• Headshell Mount: Standard SME

Transparent Sound
The Transparent Turntable plays music to any sound system, but works best with a Transparent Speaker. It plays with effortless clarity and precision, and offers playback either through cable or Bluetooth.

• Wireless Module: Bluetooth 5.0
• Phono Stage: Built in (with on/off switch)

Technical Specifications:
• Nominal speeds: 33 ⅓ and 45 RPM
• Speed variance: 33: ±0.70% 45: ±0.60%
• Wow and flutter: 33: ±0.25% 45: ±0.25%
• Signal to noise: ≥ 70dB at 1kHz, 0dB A-weighted
• Frequency range: 20-25.000Hz +3 / -3
• Stylus tip radius: r/R 8/18 µm
• Tracking force range: 1.5-2.0 g (15-20 mN)
• Tracking force, recommended: 1.75 g (17.5 mN)
• Tracking angle: 20°
• Replacement stylus unit: Ortofon Stylus 5E
• Effective tonearm mass: 13.5g
• Effective tonearm length: 220mm / 8.7in
• Overhang: 19.5mm / 0.77in
• Max power consumption: 15W
• Dimensions (W x H x D): 410 x 125 x 320 mm / 16 x 5 x 13 in
• Weight: 6,5kg / 14lb
• Dimensions packaging (W x H x D): 580 x 240 x 460 mm / 23 x 10 x 19 in
• Weight incl. packaging: 7,0kg / 15lb
• Rated input voltage: 100~240Vac, @ 50/60Hz.
• Bluetooth version: 5.0
• Normal or True Wireless (stereo) pairing
• 3.5 mm port for digital optical and analogue signals
• µUSB port for 5V power
• RX and TX mode (switch)
• Chip: Qualcomm CSR8670C
• Codec: aptX LL / SBC / MP3 / AAC
• Low Latency: <40ms
• Gold-plated contacts for perfect signal transmission

• Crafted from high quality materials and components
• Pre-mounted Ortofon OM5E Cartridge
• Pre-mounted Bluetooth 5.0 Module

Timeless Design
The Transparent Turntable is a reinvention of a classic vinyl record player, designed for a modern home and an ever evolving technology. The Transparent Turntable is meticulously crafted out of aluminium and tempered glass. It is a belt driven system with a built in phono stage, and a pre-mounted cartridge from Danish Ortofon.

• Cartridge: Ortofon OM5E (MM)
• Stylus: Elliptical Diamond

Modular
Just like all Transparent products the TT has a completely modular design. With the future in mind, it is made for flexibility, upgradability and repairability.

• Cartridge Mount: Standard ½ in
• Headshell Mount: Standard SME

Transparent Sound
The Transparent Turntable plays music to any sound system, but works best with a Transparent Speaker. It plays with effortless clarity and precision, and offers playback either through cable or Bluetooth.

• Wireless Module: Bluetooth 5.0
• Phono Stage: Built in (with on/off switch)

Technical Specifications:
• Nominal speeds: 33 ⅓ and 45 RPM
• Speed variance: 33: ±0.70% 45: ±0.60%
• Wow and flutter: 33: ±0.25% 45: ±0.25%
• Signal to noise: ≥ 70dB at 1kHz, 0dB A-weighted
• Frequency range: 20-25.000Hz +3 / -3
• Stylus tip radius: r/R 8/18 µm
• Tracking force range: 1.5-2.0 g (15-20 mN)
• Tracking force, recommended: 1.75 g (17.5 mN)
• Tracking angle: 20°
• Replacement stylus unit: Ortofon Stylus 5E
• Effective tonearm mass: 13.5g
• Effective tonearm length: 220mm / 8.7in
• Overhang: 19.5mm / 0.77in
• Max power consumption: 15W
• Dimensions (W x H x D): 410 x 125 x 320 mm / 16 x 5 x 13 in
• Weight: 6,5kg / 14lb
• Dimensions packaging (W x H x D): 580 x 240 x 460 mm / 23 x 10 x 19 in
• Weight incl. packaging: 7,0kg / 15lb
• Rated input voltage: 100~240Vac, @ 50/60Hz.
• Bluetooth version: 5.0
• Normal or True Wireless (stereo) pairing
• 3.5 mm port for digital optical and analogue signals
• µUSB port for 5V power
• RX and TX mode (switch)
• Chip: Qualcomm CSR8670C
• Codec: aptX LL / SBC / MP3 / AAC
• Low Latency: <40ms
• Gold-plated contacts for perfect signal transmission

Protect and enhance your vinyl collection with "Un-Ryu Washi" paper, only from TEAC.
The TA-TS30UN-BW is an innovative turntable sheet to provide optimized conditions for vinyl record playing.
Removing dust on vinyl records with a dust sweeper is one of the most ceremonious things when playing music, but it can be annoying to keep removing dust that won't quit.

In order to create a more comfortable listening experience, we crafted this turntable sheet from scratch with the best materials. Traditionally, silicon rubber, felt or cork are used for turntable sheets, but we went with "WASHI" to reduce statics.

"WASHI" is traditional Japanese paper made from the fibers of Mulberry trees. With natural durability, it’s been widely used for UKIYO-E printings and paper currency for centuries.

Recently, it’s been re-discovered and used for stationary and interior fabrics due to its beautiful design and excellent functionality.

By combining this WASHI with stone-paper for the core material, this turntable sheet gains mass and becomes uniformly flat, while restricting vibration, reducing static electricity and preventing dust from accumulating.

The TA-T30UN is the ultimate turntable sheet that provides an ideal condition for high quality record playing.

Specifications:
• Weight::0,24 kg
• Height: 0,300 cm
• Diameter: 31,500 cm