Turntable Accessories 142 Items

Moving Coil & Moving Magnet Phono Preamp

Squeeze every inch of detail from your record collection with our highest quality moving magnet and moving coil phono stage, with integrated headphone amp; the Duo Phono Preamplifier.

Vinyl as it's Supposed to Sound
Whether you’re dusting off your record collection or embracing analogue through the vinyl revival, there’s a unique experience to be had from the moment you drop the needle on your favourite album. To preserve the unique warmth of the vinyl sound, the Duo phono preamplifier has been carefully designed with a state-of-the-art switch mode power supply and a new surface mounted circuit board layout to reduce unwanted noise.

Why Choose a Dedicated Phono Preamplifier?
Due to the low-level signals created by a turntable, not all hi-fi amplifiers will let you connect directly to a record player. The phono preamplifier boosts this signal to something a power amplifier can work with. The challenge at this stage though is that noise can easily be added.
This is why we’ve designed the Duo around exceptional components that deliver the warm and detailed sound that’s synonymous with vinyl, all without distorting the signal from your moving magnet cartridge turntable. The switch mode power supply improves performance by switching outside of audible frequency to drastically reduce hum and new circuit board layout uses surface-mount components to reduce noise.

Vinyl. Just for You
Enjoy the warmth of vinyl privately thanks to Duo’s integrated headphone output. Uniquely, we integrated a 6.35mm headphone jack directly into the phono stage, so you can still enjoy your records when there’s no option to play out loud.
The integrated headphone output also means no need to turn on your amplifier just to power your headphones, resulting in a more eco-friendly listening experience.

Attention to Detail
If some records in your collection are a little worse for wear, the subsonic filter will help to eliminate low frequency rumbles that can be caused by imperfections within your vinyl. Combine this with the balance control for handling potential cartridge imbalances in your record player (that can cause a difference between the left and right channels) and the result is a detailed experience with accurate soundstage.

Eco Friendly
The Duo phono preamplifier is green at heart with less than half a watt standby power consumption and auto power down feature if the unit isn’t used after a 20 minute period. This in turn gives the unit the same worldwide voltage for compatibility wherever you are in the world.

Technical specifications:
• MAX POWER CONSUMPTION: 10W
• CARTRIDGE SUPPORT: Moving Magnet | Moving Coil
• GAIN @ 1KHZ: MM: 39dB | MC: 60dB
• NOMINAL OUTPUT: 300mV
• SENSITIVITY FOR NOMINAL OUTPUT: MM: 3.35mV | MC: 305uV
• EQUIVALENT INPUT NOISE (A-WEIGHTED): MM: ~0.09uV | MC: ~0.08uV
• RIAA CURVE ACCURACY: +/- 0.3dB 30Hz-50Hz
• SIGNAL TO NOISE RATIO GROUNDED INPUTS REF. 1V OUTPUT (20HZ-20KHZ BW): MM: >90dB | MC: >70dB
• THD+N 1KHZ (20-20KHZ BW): MM: <0.0025% | MC: <0.20%
• INPUT IMPEDANCE: MM: 47k Ohms | MC: 100 Ohms
• INPUT CAPACITANCE: 100pF
• OVERLOAD MARGIN: >30dB
• CROSSTALK @ 10KHZ: MM: >85dB | MC: 75dB
• DIMENSIONS (H X W X D): 48 x 215 x 159 mm (1.9 x 8.5 x 6.2")
• WEIGHT: 0.95kg (2.1lbs)
• WHATS IN THE BOX?: Alva Duo Moving Coil & Moving Magnet Phono Preamp, User Manual, Safety Guide, Mains Lead

Moving Magnet Phono Preamplifier

Enjoy every last detail from your vinyl collection with our highest quality moving magnet phono stage, the Solo Phono Preamplifier.

Vinyl as it's Supposed to Sound
Whether you’re dusting off your record collection or embracing analogue through the vinyl revival, there’s a unique experience to be had from the moment you drop the needle on your favourite album. To preserve the unique warmth of the vinyl sound, the Solo phono preamplifier has been carefully designed with a state-of-the-art switch mode power supply and a new surface mounted circuit board layout to reduce unwanted noise.

Why Choose a Dedicated Phono Stage?
Due to the low-level signals created by a turntable, not all hi-fi amplifiers will let you connect directly to a record player. The phono preamplifier boosts this signal to something a power amplifier can work with. The challenge at this stage though is that noise can easily be added.
This is why we’ve designed the Solo around exceptional components that deliver the warm and detailed sound that’s synonymous with vinyl, all without distorting the signal from your moving magnet cartridge. The switch mode power supply improves performance by switching outside of audible frequency to drastically reduce hum and new circuit board layout uses surface-mount components to reduce noise.

Attention to Detail
If some records in your collection are a little worse for wear, the subsonic filter will help to eliminate low frequency rumbles that can be caused by imperfections within your vinyl. Combine this with the balance control for handling potential cartridge imbalances in your record player (that can cause a difference between the left and right channels) and the result is a detailed experience with accurate soundstage.

Eco Friendly
The Solo phono preamplifier is green at heart with less than half a watt standby power consumption and auto power down feature if the unit isn’t used after a 20 minute period. This in turn gives the unit the same worldwide voltage for compatibility wherever you are in the world.

Technical specifications:
• MAX POWER CONSUMPTION: 10W
• GAIN @ 1KHZ: 39dB
• NOMINAL OUTPUT: 300mV
• SENSITIVITY FOR NOMINAL OUTPUT: 3.35mV
• EQUIVALENT INPUT NOISE (A-WEIGHTED): ~0.09uV
• RIAA CURVE ACCURACY: +/- 0.65dB 30Hz-20kHz
• SIGNAL TO NOISE RATIO GROUNDED INPUTS REF. 1V OUTPUT (20HZ-20KHZ BW): >90dB
• THD+N 1KHZ (20-20KHZ BW): <0.0025%
• INPUT IMPEDANCE: 47k Ohm
• INPUT CAPACITANCE: 100pF
• OVERLOAD MARGIN: >30dB
• CROSSTALK @10KHZ: >85dB
• DIMENSIONS (H X W X D): 48x176x132 (1.9x6.9x5.2”)
• WEIGHT: 0.68kg/1.5lbs
• WHATS IN THE BOX: Alva Solo Moving Magnet Phono Preamplifier, User Manual, Safety Guide, Mains lead

Ortofon’s new Test Record is designed to allow you to verify your HiFi system in the most natural audio surroundings at home. The Test Record contains special test signals developed for analyzing cartridge performance as well as its interaction with your tonearm and turntable.

Before testing your cartridge, please verify the HiFi system’s functionality. The left speaker should be connected to the left amplifier channel and vice versa; both speakers should work in phase and be optimally positioned in the room.
The Test Record is designed to be played through your system with in-built RIAA equalization. Volume control is recommended to be set at a moderate signal level.

Please refer to your turntable and tonearm’s instructions for correct installation and alignment, adjust tonearm to be parallel to record surface, set Vertical Tracking Force and antiskating according to the cartridge’s recommended technical data, and adjust stylus overhang.

The new 15-track fine pressing

Each side of the record consists of 15 tracks which have been cut from 1-4 and 5-15:

1. Frequency Sweep Left Channel 800 Hz – 50 kHz. Log. 28 sec. Linear cut* (800 – 20000 Hz ±1,5 dB)
2. Frequency Sweep Right Channel 800 Hz – 50 kHz. Log. 28 sec. Linear cut* (800 – 20000 Hz ±1,5 dB)
3. Frequency Sweep Left Channel 800 Hz – 50 kHz. Log. 28 sec. Linear cut* (800 – 20000 Hz ±1,5 dB)
4. Frequency Sweep Right Channel 800 Hz – 50 kHz. Log. 28 sec. Linear cut* (800 – 20000 Hz ±1,5 dB)
5. Reference tone 1000 Hz 5 cm/sec rms Left
6. Reference tone 1000 Hz 5 cm/sec rms Right
7. Reference tone 1000 Hz 5 cm/sec rms Left
8. Reference tone 1000 Hz 5 cm/sec rms Right
9. Tracking ability, lateral 50 ?m peak
10. Tracking ability, lateral 60 ?m peak
11. Tracking ability, lateral 70 ?m peak
12. Tracking ability, lateral 80 ?m peak
13. Tracking ability, lateral 90 ?m peak
14. Tracking ability, lateral 100 ?m peak
15. Square Wave Form 2.7 msec duty cycle 3:7
* The record has a constant velocity amplitude throughout the sweep.

1-4 Frequency sweep – a tool for checking frequency response
There are several factors which can affect frequency response, including cable capacitance, cartridge loading, tracking force and worn parts. Because of this, it can be difficult to achieve perfectly flat frequency response. Sometimes by making small compromises in the cartridge loading, a better overall frequency response can be achieved. Considering the above the signal must be clean throughout the sweep.

5-8 Reference tone for testing channel output
With this standard reference signal is it possible to check the correctness of the connections of the left and right channels, channel balance and speed of the turntable.

9 -14 Tracking ability test, 315 Hz lateral modulation
These tracks contain a 315 Hz signal, recorded at increasing pick amplitudes of 50, 60, 70, 80, 90 and 100 micrometers. Please refer to your cartridge’s tracking ability value specified in the technical data sheet. Your cartridge should be able to track the actual level without audible distortion. Inability to track can be heard as a departure from a pure tone or a sputtering and intermittent tone. To determine if it is one or both channels, the balance control can be utilized. In case of differing tracking ability in the left and right channels it is probably necessary to readjust the anti-skating correction of the tonearm. If both channels fail to track properly, then vertical tracking force should be increased until no further improvement of tracking force can be obtained.

15. Square Wave Form 2.7 msec duty cycle 3:7
When monitoring the output of your cartridge with an oscilloscope you’ll then see a square wave located precisely above each other if the connection from the cartridge is correct.

After successful completion of the above test procedures, you can ensure that your cartridge is optimized. Still the human ear is very sensitive to difference in tone distortion; its level depends on the stylus condition and record wear.

To maintain optimal sound reproduction and to minimize wear on your records as well as on your stylus, we recommend the following procedure before and after each playback:
• Remove dust carefully from record surfaces by using a fine antistatic brush or cloth before every use.
• Please remember to remove dust from the diamond tip before and after playback of each record
• I order to keep electrical contacts clean and to lubricate the knurled nut on the tonearm, Ortofon recommends occasionally a light spray of contact cleaner like DeoxIT ®Gold G-Series into the tonearm socket.

It should be noted that some phono equalizers may generate some tone distortion, which cannot be referred to the cartridge.

User Guide: https://www.ortofon.com/media/148619/ortofon-test-record-user-guide.pdf

Quartz controlled 300 Hz light source

Enables exact adjustment of your turntable speed by keeping the light source independent from fluctuations in the mains frequency and voltage, which would otherwise give distorted results. A quartz oscillator generates an accurate 300 Hz, white light source, making precise speed adjustment easy when used in conjunction with the Clearaudio Stroboscopic Testrecord.

An optimal listening experience requires precise settings, especially when it comes to motor speed. The clearaudio Speed Light V2 is your key to accurate speed adjustments, regardless of the power grid frequency in your country. In this enhanced version, we present an upgrade for ultimate precision and user-friendliness.

New features at a glance:

White LED for improved visibility:
The transition from a blue LED to a white LED ensures an even better visibility of the line pattern on the stroboscopic disc. Every pulse is accurately captured, allowing for precise speed adjustments.

Extended operating time with a new battery:
The switch to the lithium button cell (CR2023) not only provides a longer operating time but also ensures a constant power supply for reliable performance. The Speed Light V2 does not have a rechargeable battery and operates only on a battery or continuous power.

New Micro-USB port for battery-independent operation:
The implementation of a Micro-USB port offers the option of battery-independent operation.

Aluminum casing:
The casing, milled from solid material and made of anodized aluminum, replaces the previous plastic, improving durability and adding an aesthetically pleasing element.

Compatible with the Stroboscopic Test Record:
The clearaudio Speed Light V2 is perfectly tuned for use with our Stroboscopic Test Record.

Manual: https://www.clearaudio.de/_assets/_pdf/manuals/accessories/CA_Speed%20light%20V2_E+D.pdf

Providing unbeatable accuracy! The Stroboscope Testrecord together with the Speed Light V2 give the best results in adjusting your turntable speed.

Enables exact adjustment of your turntable speed by keeping the light source independent from fluctuations in the mains frequency and voltage, which would otherwise give distorted results. A quartz oscillator generates an accurate 300 Hz, white light source, making precise speed adjustment easy when used in conjunction with the Clearaudio Stroboscopic Testrecord.

An optimal listening experience requires precise settings, especially when it comes to motor speed. The clearaudio Speed Light V2 is your key to accurate speed adjustments, regardless of the power grid frequency in your country. In this enhanced version, we present an upgrade for ultimate precision and user-friendliness.

New features at a glance:

White LED for improved visibility:
The transition from a blue LED to a white LED ensures an even better visibility of the line pattern on the stroboscopic disc. Every pulse is accurately captured, allowing for precise speed adjustments.

Extended operating time with a new battery:
The switch to the lithium button cell (CR2023) not only provides a longer operating time but also ensures a constant power supply for reliable performance. The Speed Light V2 does not have a rechargeable battery and operates only on a battery or continuous power.

New Micro-USB port for battery-independent operation:
The implementation of a Micro-USB port offers the option of battery-independent operation.

Aluminum casing:
The casing, milled from solid material and made of anodized aluminum, replaces the previous plastic, improving durability and adding an aesthetically pleasing element.

Manual: https://www.clearaudio.de/_assets/_pdf/manuals/accessories/CA_Stroboscope%20Testrecord%20+%20Speedlight_E+D.pdf

Dustprotector for turntable
The Clearaudio Dustprotector is not only an eye-catcher on your turntable, it also prevents the accumulation of dust on the turntable, so you don't have to clean the platter before using it.

Level Gauge - Basic
High precision gauge, calibrated.

Pro-Ject standard dust cover Type 1, suitable for chassis like Debut, 1, 1.2, Xpression.

Spare needle for the Cruiser Portable Turntable from Crosley.

Every once and a while you need to take care of your record player. This is the NP6 stylus replacement needle which is compatible for these record players:

• Cruiser Deluxe
• Voyager
• Lancaster

Crosley NP 6 Spare Needle - features:

• ABS Plastic Composition
• Stylus Needle
• plays 3 speeds - 33 1/3, 45 and 78 RPM records

AT618a
Disc Stabiliser

• Holds record firmly in place stabilising the record
• Thick rubber construction
• 600g

Replacement Technics LED Target Lights!

Switch up from the standard stock Technics target light.

• Surface mount LED's for long life
• Illuminates outward - no reflector
• Balanced voltage - no resistors needed
• Easy installation - soldering required
• Comes as a pair - x2 LED circuit boards. (Connect with cables from SL unit.)
• Suitable for SL1200MK2, SL1200MK3, SL1200M3D, SL1210MK2

Installation Video: https://www.youtube.com/watch?v=5FNUq3_bWY4&feature=youtu.be

Replacement Technics LED Target Lights!

Switch up from the standard stock Technics target light.

• Surface mount LED's for long life
• Illuminates outward - no reflector
• Balanced voltage - no resistors needed
• Easy installation - soldering required
• Comes as a pair - x2 LED circuit boards. (Connect with cables from SL unit.)
• Suitable for SL1200MK2, SL1200MK3, SL1200M3D, SL1210MK2

Installation Video: https://www.youtube.com/watch?v=5FNUq3_bWY4&feature=youtu.be

PT01 Felt Replacements!

Easy to apply felt replacements for your PT01 Series turntables.

Self adhesive.

Straight outta SoCal.

An upgraded replacement platter belt for the Numark PT01 portable turntable.

Thicker than the stock belt
Wider than the stock belt
Better grip and torque
Compatible with all Numark PT01 Series

PT01 Felt Replacements!

Easy to apply felt replacements for your PT01 Series turntables.

Self adhesive.

Straight outta SoCal.

Omni Portable Turntable Tone Arm Tension Mod by Tiny Steppa

Enhance Durability. Unleash Potential.

"The tone arm tension design in the Omni is actually very simple, with the two rubber bands doing their job well. However, we're aware that rubber bands can become hard and lose elasticity over time, much like changing a platter belt after a long while. This modification gives you an option to enhance durability, and elevate Omni's potential."

Easy stylus weight adjustment: Fine-tune the stylus weight with your fingertips.
Tone arm protection: Nylon screws prevent tonearm coating damage during setup.
Simple installation: Quick and user-friendly assembly.
Tool kit included: All necessary tools are in the package.
Omni certified: Meets quality and compatibility standards.

Installation video can be found here:
https://www.youtube.com/watch?v=ctHskU8k67c

Watch the adjustment video here:
https://www.youtube.com/watch?v=TDKhq1hTC3s

High-tech lubricant for constant velocity

How to use Lube it:
A turntable is a delicate instrument and needs proper care. The motor is moving the platter and the bearing‘s lubrication is being worn off over time. This is caused by many factors, such as climate and humidity. Therefore we cannot give a recommended time as to when to replace the lubrication. Best is to keep it constantly lubricated. With Lube it you can keep the bearing of your turntable smooth for a perfect playback. We recommend to keep your turntable constantly moving, as this guarantees a smooth bearing. This however will lead to metal abrasion, so you will need to change the lubrication more often. As to how much you should use, we can only advise to use the amount you feel right. It can‘t be too much, worst case scenario is you will have to clean some lube off your turntable to keep it looking clean.

Please only use Lube it for turntables like Elemental, Primary, T-Line, Essential, Debut, The Classic, Juke Box & X1/X2.
For inverted bearings like RPM Line, Xtension models and Signature Line please use Grease it.

Features:
• Helps a smooth movement
• Easy handling

Amount: 5 ml

Replacement Technics LED Target Lights!

Switch up from the standard stock Technics target light.

• Surface mount LED's for long life
• Illuminates outward - no reflector
• Balanced voltage - no resistors needed
• Easy installation - soldering required
• Comes as a pair - x2 LED circuit boards. (Connect with cables from SL unit.)
• Suitable for SL1200MK2, SL1200MK3, SL1200M3D, SL1210MK2

Installation Video: https://www.youtube.com/watch?v=5FNUq3_bWY4&feature=youtu.be

Reloop - Abdeckhaube / Dust Cover RP-7000/8000/+MK2

FEATURES
Hinged dust cover
Suitable for Reloop RP-7000/8000 MK1 and MK2
Sturdy rigid plastic cast
TECHNICAL DATA
Dimensions: 452 x 58 (75 tone arm base) x 348 mm (358 hinge seat)
Incl. mounting hinges

OFFERED IS JUST THE DUST COVER WITHOUT TURNTABLE!

Machined aluminium housing turntable leveler that provides a precise level for horizontal adjustment of the turntable.

Stabilize your records

Reduces unwanted resonances & improves playback of warped records. The label is protected by the felt pad on the underside.

OPTIMIZED PLAYBACK OF YOUR RECORDS
This Record Puck PRO ensures a firm fit between the record and the turntable. Record pucks use weight to secure a record against the turntable. This improves the sound performance of the turntable in terms of timing and sound depth.

Technical Specifications:
• Material: Nickel-plated aluminium
• Weight: 190g
• Diameter: 78mm
• Height: 16mm

Ortofon Record Stabilizer Heavy - Black - 350 g

The Ortofon Record Stabilizer is offered in two versions: Standard and Heavy, meticulously designed to seamlessly complement a variety of turntables. Completely reengineered, these stabilizers boast an elegant aesthetic and user-friendly functionality. No preparations are needed; simply place the stabilizer on the record before playback to experience improved playback with reduced vibration.

Crafted with precision, the Ortofon Record Stabilizer comes in a premium satin matte anodized finish, available in Silver or Black, featuring the distinctive Ortofon textured wave-grip. The Standard version is ideal for entry-level and sub-chassis turntables, made from aluminum with a smooth felt underside.

Enhance your vinyl listening experience effortlessly with the Ortofon Record Stabilizer, where form meets function for optimal sound performance.

Heavy weight record puck

This heavy Record Puck ensures a firm fit between the record and the platter surface.

Record pucks use weight to secure a playing vinyl record against the turntable platter. By holding the two together, the sound performance of the turntable will improve, in timing and depth of sound.

We recommend using heavy weight clamps on RPM, Signature & Xtension series turntables.

The alternative way to achieve this effect on smaller turntables is our record clamp Clamp it.

Features:
• Reduces unwanted vibrations
• Helps with optimum playback of warped records

Technical Specifications:
• Material: Brass
• Weight: 800g
• Diameter: 780mm
• Height: 260mm

Record Spindle Holders!

For all turntables - simply push onto the spindle and keep your slipmat and vinyl locked down!
• Soft silicon
• Pack of 5
Straight outta SoCal.

An upgraded replacement platter belt for the Reloop SPIN portable turntable.

Thicker than the stock belt
Wider than the stock belt
Better grip and torque
Compatible with Vestax Handy Trax

The Reloop SPiN Tone Arm by Jesse Dean Designs.

Straight outta SoCal.

Easy installation for your Reloop SPiN.

Engineered to work with;

- Ortofon OM style
- Reloop OM-GT
- Shure M44-7

Super stable design and accepts all magnetic cartridges!

- Constructed from FR4 fibre board
- Adjustable brass counter weight
- Front LED target light
- Phono analogue pre-amp included
- Magnetic clip for housing
- Easy wire installation kit, including cartridge mounting screws

Match it with a JDDX2R-SP SPiN contactless fader!?

Please note: The JDD-SPCB does not include a cartridge and stylus.

Installation Video: https://www.youtube.com/watch?v=NyBZpw0tuhw&feature=youtu.be&fbclid=IwAR32dn4iAJAp5fNS8pGmC8_vYDIPBIhEV_y1YNBRQYoEJ5Eeu5igEldFFHw

Introducing the new budget build tone arm by Jesse Dean Designs!

Compatible with any PT01 or Handytrax portable turntable!
Straight outta SoCal.
Battle tested at Portablist Lounge.
Easy install.

A far superior improvement over the factory tone arm.

• Constructed from Fr4 fiberboard
• ABS molded gimbal
• Adjustable brass counter weight
• Front LED target light
• Preamp included - no soldering required
• Magnetic clip for housing

Engineered to work with almost every cartridge like:
• Ortofon OM style
• Reloop OM-GT
• M447

Please note: The JDDPTA-PCB does not include a cartridge and stylus.

JDDPTA-PCB installation video: https://www.youtube.com/watch?v=5dHAPSt4yfo&feature=youtu.be&fbclid=IwAR1xzjGcWeySRyexDii-fJI_-1S5B2lr4h6NaRTuuQ4_9uEKaECb62LDDD0

Designed to mount on a manual turntable, the AT6006R Safety Raiser automatically lifts the tonearm at the end of a record, protecting the stylus from damage. The raiser is equipped with a highly sensitive release antenna and a hydraulic lift with rubber lift bar, ensuring safe, smooth and dependable operation. Height adjustment knob and included spacers allow the raiser to be used with a wide variety of turntables with different tonearm heights.

Specifications
Dimensions: 14 mm (0.55") diameter × 27 mm (1.06") to 39 mm (1.54") height*
Lift bar movable width: 3 mm (0.12")
Weight: Approx. 21 g (0.74 oz)
Accessories: Double-sided tape ×4, Spacer ×2 (14 mm (0.55") diameter × 12 mm (0.47") height; 14 mm (0.55") diameter × 24 mm (0.94") height)

* In standby. Height can be adjusted by using the height-adjustment knob and included spacers.

Electronic stylus balance

The Measure it S2 Stylus Tracking Force Gauge is a highly accurate electronic balance that is designed for measuring stylus trackingforces up to 5.0 grams in 0.001 gram increments. Each Measure it S2 can easily be calibrated with the included calibration weight. The Measure it S2 has a solid aluminum housing with a 4-digit LCD backlit display. Whenever in doubt about the actual amount of pressure on the diamond tip the 4 digit display of this smart tool will help. Armed with precise information about tracking force, your stylus tip wear can be significantly reduced.

Scope of delivery:
• stylus balance
• calibration weight
• screwdriver
• 2x AAA batteries
• protection case for the meter
• user guide

Features:
• 4 digit LCD-Display with backlight
• Capacity 0 - 5g
• Variance ±0,001g
• Auto calibration function
• Auto off after 60 seconds
• Replacement batteries supplied

Technical Specifications:
• Capacity: 0 - 5g
• Variance: ±0,001g
• Weighting modes: gram (1g = 10mN), ounce (oz), pennyweight (dwt) and carat (ct)
• Display: 4 digit LCD with backlight
• Calibration: Auto calibration using a 5g weight
• Auto off: 60 seconds off
• Replacement battery: 2 x AAA cells, 1,5V
• Operating temperature: +10 - +30°C (50 - 86 degrees Fahrenheit)
• Dimensions (W x H x D): 122 x 27 x 55mm
• Weight: 170g

Ortofon Record stabilizer - Black - 240 g

The Ortofon Record Stabilizer is offered in two versions: Standard and Heavy, meticulously designed to seamlessly complement a variety of turntables. Completely reengineered, these stabilizers boast an elegant aesthetic and user-friendly functionality. No preparations are needed; simply place the stabilizer on the record before playback to experience improved playback with reduced vibration.

Crafted with precision, the Ortofon Record Stabilizer comes in a premium satin matte anodized finish, available in Silver or Black, featuring the distinctive Ortofon textured wave-grip. The Standard version is ideal for entry-level and sub-chassis turntables, made from aluminum with a smooth felt underside.

Enhance your vinyl listening experience effortlessly with the Ortofon Record Stabilizer, where form meets function for optimal sound performance.

760 g layer weight to stabilize vinyl records.
Ø 70mm

Dust Cover RP-1000/2000/4000/ +MK2

FEATURES
• Hinged dust cover
• Suitable for Reloop RP-1000/2000/4000 MK1 and MK2
• Sturdy rigid plastic cast

TECHNICAL DATA
• Dimensions: 442 x 68 x 348 mm (358 hinge seat)
• Incl. two hinges

OFFERED IS JUST THE DUST COVER WITHOUT TURNTABLE!

Ortofon Record stabilizer - Silver - 240 g

The Ortofon Record Stabilizer is offered in two versions: Standard and Heavy, meticulously designed to seamlessly complement a variety of turntables. Completely reengineered, these stabilizers boast an elegant aesthetic and user-friendly functionality. No preparations are needed; simply place the stabilizer on the record before playback to experience improved playback with reduced vibration.

Crafted with precision, the Ortofon Record Stabilizer comes in a premium satin matte anodized finish, available in Silver or Black, featuring the distinctive Ortofon textured wave-grip. The Standard version is ideal for entry-level and sub-chassis turntables, made from aluminum with a smooth felt underside.

Enhance your vinyl listening experience effortlessly with the Ortofon Record Stabilizer, where form meets function for optimal sound performance.

The TTW10H is our turntable weight which combines two needful features for every vinyl DJ:
A disc stabilizer and an adapter for 7“ records.
The difference to the classic TTW10 is the material used for the outer part: The heavy weight edition is machined out of high-grade stainless steel which results in a final weight of 808g / 1.78lbs.

OUR HANDCRAFTED TURNTABLE WEIGHTS WORK EITHER FOR 12“ AND 7“ RECORDS.

Our turntable weights feature a smart mechanism: The 7“ adapter inside the weight is moveable- as soon as you put the weight on a 7", the adapter will fall down through the big hole of the vinyl. Your record is now centered and stabilized by the TTW10H. If you place the kit on a 12“ record, the adapter will remain in the rear position and stabilizes your warped records. A sticky rubber mat on the bottom side protects your vinyl and allows you to control the record in a very direct way. The TTW10H comes in a neat printed box with a linen bag to take it out to your gigs.

The difference to the classic TTW10 is the material used for the outer part: The heavy weight edition is machined out of high-grade stainless steel which results in a final weight of 808g / 1.78lbs.

STAINLESS STEEL BODY WITH A SOLID BRASS CORE.

• DIMENSIONS: Ø75mm × 33mm (Ø2.9 × 1.3 inches)
• WEIGHT: 808g (1.78 lbs)

Handmade in Switzerland

Video: https://youtu.be/e1be_0Ijhms
https://youtu.be/Z8ng431G528?list=PLcGzoHkRXIiapmclhU9L9GtVyQcTGCz1g

The number 1 turntable weight used by Dj's in the world!

MasterSounds x HHV turntable weights are carefully designed to reduce a turntable’s noise floor and thus improve the musical soundstage. Users enjoy improved bass response, tighter mids and controlled highs as the turntable weight reduces unwanted resonance when placed via the spindle on top of a record. MasterSounds x HHV turntable weights weigh just over 400 grams (+/- 14oz), light enough to not cause damage to a turntable’s bearing system, but heavy enough to give sonic improvement.

MasterSounds x HHV weights have been tested on a large variety of non-suspended belt drive and direct drive turntables with great success. Pressing plants try to achieve quality control on every record made, however there are intrinsic issues such as dished and warped records. MasterSounds x HHV turntable weights help to combat this too. DJs love this; as it aids cueing a problematic a record prior to mixing and eliminates needle skip.

It was developed an anti-slip base for MasterSounds x HHV weights, and thus each turntable weight has been designed to grip the record, which is fantastic for DJ’ing as it really stabilises records in the mix. Use MasterSounds x HHV turntable weights for a couple of weeks then remove to realise what a difference they make!

• Satin Titanium with white HHV graphic
• Hand-brushed finish
• Premium quality turntable weights developed for club and home use
• Hand made in quality aluminium, limited "edition" numbers
• Simply pop a record on your turntable and place the turntable weight over the spindle to enjoy a wider, deeper sound stage with extended bass and improved sound throughout the frequency spectrum
• Stabilises your record when playing in a club, bar or at home
• Less needle skip
• Rubber anti-slip base
• Supplied in velvet style pouch for transport
• 80mm diameter X 41mm high
• ca. 400g

RCA cable for your Technics turntable!

No need to worry about earthing your Technics turntable anymore!

Easy installation.

• 1m/3ft flexible soft cable
• Low oxide copper wire
• Gold contact RCA plugs
• Internal ground PCB
• Large solder pads
• Reinforced secure cable

Straight outta SoCal.

Installation video:
https://youtu.be/Pqe8UsRT-bU

Need more control with your Reloop SPiN when trying to balance vinyl and audio levels?

When using a third party fader for your SPiN - get the most from your redundant stock fader!

Simply plug the OEM RSVCB inline with the stock fader and configure the switch settings accordingly!

•Easy installation
•No soldering
•Switch between Vinyl, Aux or Crossfade
•Vinyl volume control - default

Carbon Fibre Tone Arm for the Stanton STX Portable Turntable.

Available with Black gimble.

Engineered to work with:

• 3K carbon fibre tube and aluminum head shell
• Billet aluminum gimbal with ball bearings
• Custom engineered limited bounce tension system
• Phono analogue pre-amp included
• Easy wire installation kit, including cartridge mounting screws
• Engineered to work flawlessly with: Ortofon VNL/OM, Reloop OM-GT and Shure M44-7

Please note: The JDDPTA-SX does not include a cartridge and stylus.

Why not get the tonearm with a Ortofon VNL Cartridge & Stylus?

Installation video can be found here:
https://www.youtube.com/watch?v=pQsXTqpkfjQ

Expert 12 in 1 turntable care kit - A must-have accessory

The Lenco TTA-12IN1PRO is an aluminium suitcase containing all necessary accessories for taking care of your turntable and records collection.

The contents:
A record anti-static brush to clean your records, a stylus force scale to check the pressure of the stylus on the record, a cartridge azimuth and VTA protractor and a cartridge alignment protractor to make sure that your cartridge is perfectly aligned for the best sound performance.
4 small level gauges and a bigger level gauge to make sure that your turntable is perfectly horizontal.
In case you want to change your cartridge you will find pliers, 4 cartridge wires, 12 cartridge screws and a small screw driver.
To keep the stylus clean we provide a stylus brush.
Plus gauge & 45rpm adapter.

Included : Record anti-static brush, Stylus force scale, Cartridge azimuth and VTA protractor, Cartridge alignment protractor, 4 small level gauges, Pliers, 4 cartridge wires, 12 cartridge screws, Screw driver, Stylus brush, Big level gauge, 45rpm adapter

Turntable platter

Functional and easy to use sound improvement!

Upgrade your Elemental or Essential turntable with Acryl it E. Acryl it E is made from acrylic with satinised surface and brings a more liquid sound that leaves no space for platter resonances.

The change is easily made: just exchange your metal platter for Acryl it E. Acryl it E is able to improve overall performance significantly!

Features:
• Suitable for Elemental, Essential & Primary turntables
• Substitutes MDF platter
• Inert material avoids resonances
• Ideal for use with Clamp it
• Audiophile sound tuning
• Optical upvaluation

Technical Specifications:
• Material: Acryl satiniert
• Diameter: 300 mm
• Height: 20 mm
• Weight: 1,2 kg net

A universal stroboscopic disc used to show the running speed of the turntable at 33 and 45 RPM with a spindle radius guide.

Record weight made of aluminum with an integrated Teflon bushing on the underside for smooth placement (332 g).

This high-quality accessory, available in silver or black anodized aluminum, is specifically designed for the Performance series and stands out with its stylish design and exceptional functionality. Of course, this weight can also be used with other Clearaudio models and other brands.

The Performance record weight features an integrated Teflon bushing on the underside, ensuring smooth placement and significantly easing handling. At the same time, the weight is softly decoupled from the spindle. With a precisely calibrated weight of 332 grams, it is tailored for turntables with CMB bearings and clearaudio DC motors, making it the perfect complement to these systems.

Additionally, the record weight is compatible with all radial tonearms as well as the TT5 tonearm, making it a versatile accessory for audiophiles and professional users alike.

Weight: 332 g

Record weight made of aluminum with an integrated Teflon bushing on the underside for smooth placement (332 g).

This high-quality accessory, available in silver or black anodized aluminum, is specifically designed for the Performance series and stands out with its stylish design and exceptional functionality. Of course, this weight can also be used with other Clearaudio models and other brands.

The Performance record weight features an integrated Teflon bushing on the underside, ensuring smooth placement and significantly easing handling. At the same time, the weight is softly decoupled from the spindle. With a precisely calibrated weight of 332 grams, it is tailored for turntables with CMB bearings and clearaudio DC motors, making it the perfect complement to these systems.

Additionally, the record weight is compatible with all radial tonearms as well as the TT5 tonearm, making it a versatile accessory for audiophiles and professional users alike.

Weight: 332 g

Bearing lubricant

How to use Grease it:
A turntable is a delicate instrument and needs proper care. The motor is moving the platter and the bearing‘s lubrication is being worn off over time. This is caused by many factors, such as climate and humidity. Therefore we cannot give a recommended time as to when to replace the lubrication. Best is to keep it constantly lubricated. With Grease it you can keep the bearing of your turntable smooth for a perfect playback. We recommend to keep your turntable constantly moving, as this guarantees a smooth bearing. This however will lead to metal abrasion, so you will need to change the lubrication more often. As to how much you should use, we can only advise to use the amount you feel right. It can‘t be too much, worst case scenario is you will have to clean some grease off your turntable to keep it looking clean.

Please only use Grease it for turntables with inverted bearings, like RPM Line, Xtension models and Signature Line.
For non-inverted bearings you should use Lube it.

Features:
• To be used with inverted bearings
• Helps a smooth movement
• Pre-filled syringe
• Easy handling

Amount: 2.3 ml

MM Phono Pre-amplifier

Good sound from sound technology
• Metal case shields the electronics from vibrational and electromagnetic interference
• Special low-noise ICs used
• Optimal channel separation through dual-mono circuitry
• Gold plated RCA connection sockets
• DC power supply (< 1 watt standby power)

Features
• Amplification and RIAA equalisation for MM cartridges
• Small size allows installation close to record player

107x36x104 (115)mm

Manual: http://www.project-audio.com/inhalt/en/manual/manual_phonoboxmm.pdf

Stroboscope Testrecord for optimum control of the absolute speed

The tool to tune the optimal and exact speed of your turntable. The Stroboscopes break-in groove creates the additional stylus drag necessary to accurately measure the real-time speed of your turntable, and can also be used to break in new cartridges.
For the best possible accuracy, use in combination with our Speed Light.

Manual: https://clearaudio.de/_assets/_pdf/manuals/accessories/CA_Stroboscope%20Testrecord_E+D.pdf

The TTW10 from Varia Instruments is a turntable weight which combines two needful features for every vinyl DJ: A disc stabilizer and an adapter for 7“ records. So, it works either for 12" and 7" records.

The Varia Instruments TTW10 features a smart mechanism: The 7“ adapter inside the weight is moveable - as soon as you put the weight on a 7", the adapter will fall down through the big hole of the vinyl. Your record is now centered and stabilized by the TTW10. If you place the kit on a 12“ record, the adapter will remain in the rear position and stabilizes your warped records. A sticky rubber mat on the bottom side protects your vinyl and allows you to control the record in a very direct way.

The TTW10 comes in a neat printed box with a linen bag to take it out to your gigs.

• dimensions: Ø75mm x 31mm (Ø2.9 x 1.2 inches)
• weight: 466g (1.02 lbs)
• handmade in Switzerland

Video: https://youtu.be/Z8ng431G528?list=PLcGzoHkRXIiapmclhU9L9GtVyQcTGCz1g

The Ortofon Tonarmwaage is a scale that helps to adjust the perfect tone arm weight. A great tool for perfectionists! Range: 0.8 up to 3.0 g.

Acrylic dust cover for Concept Signature.
Dimensions (W/D/H in mm): 450 x 380 x 147 (Outer dimension)

760 g layer weight to stabilize vinyl records.
Ø 70mm

Single puck

Precision machined single record puck!

Fits all brands and types of turntables and places your 7“ vinyls exactly centrally on the turntable. Adapt it is made from non-magnetic metal, that makes it look first-class. Unlike cheap plastic solutions the Adapt it is unbreakable!

Features:
• Adaptor for use with 7-inch single records
• Locates record centrally on turntable
• No plastic - precision CNC-machined
• Non-magnetic aluminum
• Suitable for all brands and types of record players

Technical Specifications:
• Material: Aluminum, CNC twisted
• Diameter: 38 mm
• Height: 10 mm

Equipment base

Ground it E is a stable and height-adjustable platform for turntables, that will reduce negative effects of potential surface vib-rations significantly. The use of Ground it E is very simple: Do not place your turntable directly on surfaces such as furniture or shelves that may be vibration sensitive, but place it on Ground it equipment bases. All Ground it bases will improve the sonic performance, so a pleasant, natural reproduction of vinyl music will be possible. The playback quality of a turntable placed on Ground it E will benefit because of improved dynamics and coherent timing. The ambient acoustic of the recording venue will sound much clearer and contoured, so music playback appears to be more realistic, authentic and expressive.

Suitable for:
• Elemental Line
• Essential Line
• Debut Line
• 1Xpression Carbon
• 1Xpression Carbon Classic
• RPM1 Carbon
• RPM3 Carbon

Features:
• Support platform for many turntables or other equipment
• Prevents the transmission of vibrations
• Heavy-weight MDF
• Conical feet with damping ring
• Height adjustable
• Combinable with Cover it E and Cover it RPM 1/3 Carbon
• High gloss piano finish

Technical Specifications:
• Dimensions: 480 x 51 x 390 mm spike feet incl.
• Weight: 4 kg

Jesse Dean Face Plate for your Stanton STX portable turntable.

Swap out your stock or JDDX2R-SX face plate with one of these!

Available colours:

Black
Blue
Red
White

An easy to use tool that quickly corrects undersized spindle holes – fitted with an ergonomic aluminum handle.
Diameter (Ø): 7.3 mm

Spirit level

Spirit level for optimum positioning of a turntable.

Digital start stop button for your portable turntable!

A highly efficient start stop button kit by Jesse Dean, that only draws less than 1mA...

• No need for latching relays
• No soldering
• No noise
• Powered from the turntable motor
• PT01 series and Handytrax ready

The kit includes:

• Digital JDD start/stop controller board
• 16mm aluminum momentary button
• 400mm button wire
• x2 wire crimps

Installation video:
https://youtu.be/wIAFvCDCh-o

Level Gauge - Stainless steel
High precision gauge, calibrated.

Record clamp.
LP-clamping unit with resonance absorbing locking unit and stainless steel grip.
Weight: 190 g

Support weight for mass drives

The weight made of stainless steel ensures a better contact between the record and the platter. This suppresses mechanical resonances, which greatly improves the scannability of the microgroove. As a result, your music becomes more detailed, has a clearer resolution and a better defined bass. The ergonomic shape ensures easy handling when placing the weight on the record. It is not necessary to screw it onto the plate mandrel. The contact weight is a little over 500 grams.

Details and technical data:
• Precisely processed by CNC milling
• Avoidance of disruptive resonances, which have a negative effect on the scanning by your pickup
• Made of solid stainless steel for the perfect combination of weight (a little more than 500 grams) and size
• Ergonomic shape for easy handling
• Diameter: 73 mm
• Height: 22mm
• Diameter of the hole for the plate mandrel: 7.5 mm
• Made in Japan

Introducing the new budget build tone arm by Jesse Dean Designs!

Compatible with any PT01 or Handytrax portable turntable!
Straight outta SoCal.
Battle tested at Portablist Lounge.
Easy install.

A far superior improvement over the factory tone arm.

• Constructed from Fr4 fiberboard
• ABS molded gimbal
• Adjustable brass counter weight
• Front LED target light
• Preamp included - no soldering required
• Magnetic clip for housing

Engineered to work with almost every cartridge like:
• Ortofon OM style
• Reloop OM-GT
• M447

Please note: The JDDPTA-PCB does not include a cartridge and stylus.

JDDPTA-PCB installation video: https://www.youtube.com/watch?v=5dHAPSt4yfo&feature=youtu.be&fbclid=IwAR1xzjGcWeySRyexDii-fJI_-1S5B2lr4h6NaRTuuQ4_9uEKaECb62LDDD0

Target light for your portable!

Who needs to navigate across vinyl anymore?

• Easy install
• Bright LED
• Billet aluminum black housing
• JDD power break out board

Straight outta SoCal.

Installation video:
https://youtu.be/yfmVJGAlJ2E

Premium Alignment Tool

Your go-to precision companion for perfecting your turntable setup. Crafted to the highest standards, this tool is a larger and sturdier version, boasting a remarkable 75% increase in rigidity compared to the standard model.

The Premium Cartridge Alignment Tool features a robust build, providing enhanced durability and stability during the alignment process. Its larger size ensures a more secure grip and heightened accuracy.

With two zero points Baerwald alignment, this tool is engineered to deliver optimal tracking performance. Achieve precise cartridge alignment for accurate playback, allowing you to experience your vinyl collection with unparalleled clarity and fidelity.

How to use the alignment tool:
https://ortofon.com/pages/alignment-tool

Stroboscope disc

Control of turntable speed.

Strobe it shows circular arranged dashes that are assigned to speed and frequency. Please remember the ring that matches your desired speed and frequency (33 1/3 rpm with 50 Hz and 45 rpm with 50 Hz are valid for Europe). Put Strobe it on the turntable platter and start the turntable. The tonearm remains in its initial position. Align a mains powered light source directly to the turntable with Strobe it rotating. The dashes of the previously pinned ring should now give the impression to stand still. If they seem to move slightly forward or backwards, the speed is either too high or too low. Please note: Use normal mains operated lamps. Daylight, fluorescent lamps (energy saving lamps) as well as flashlights and LEDs, which are operated with direct current, are not suitable.

Ortofon Record Stabilizer Heavy - Silver - 350 g

The Ortofon Record Stabilizer is offered in two versions: Standard and Heavy, meticulously designed to seamlessly complement a variety of turntables. Completely reengineered, these stabilizers boast an elegant aesthetic and user-friendly functionality. No preparations are needed; simply place the stabilizer on the record before playback to experience improved playback with reduced vibration.

Crafted with precision, the Ortofon Record Stabilizer comes in a premium satin matte anodized finish, available in Silver or Black, featuring the distinctive Ortofon textured wave-grip. The Standard version is ideal for entry-level and sub-chassis turntables, made from aluminum with a smooth felt underside.

Enhance your vinyl listening experience effortlessly with the Ortofon Record Stabilizer, where form meets function for optimal sound performance.

The Classic Plate is the upper half of the Plate X One. An additional X One is needed.

Suitable for: Numark PT01, Numark PT01 Scratch, Numark PT01 USB
Material: aluminum

Attention: only the plate!
The X One must be ordered separately: item 845663

Jesse Dean Decal Kit for your Stanton STX portable turntable.

Swap out or cover your stock blue decals!

Available colours:

Black
Red
White