DJ Equipment 356 Items

The 2M 78 features an improved engine, which provides a high level of sonic accuracy. The stylus' tip is a Spherical diamond that is perfect for playback of 78 rpm shellac records, which require a larger stylus profile. The cartridge body is manufactured from Hopelex, which ensures high rigidity while eliminating unwanted resonances.

2M 78 uses a strapped output to deliver the same output signal from both sets of pole pins. This effectively eliminates the need for mono-specific equipment, making it possible to enjoy true mono reproduction on any stereo playback system.

The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M 78 Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4 mV
• Frequency response - 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 70 µm
• Compliance, dynamic, lateral - 18 µm/mN
• Stylus type - Spherical
• Stylus tip radius - R 65 µm
• Tracking force range - 1.6-2.0g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Internal impedance, DC resistance - 700 Ohm
• Internal inductance - 350 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Tracking angle - 20°
• Cartridge colour, body/stylus - Black/Grey
• Cartridge weight without screws - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M 78 (interchangeable with 2M Mono)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

Next level authenticity with the 2M Blue
The goal for any cartridge should be to reproduce the sound as close to the artists vision as possible, and the 2M blue takes you further on this journey of authenticity. With the 2M Blue, you get serious about listening to vinyl.

Features:
The 2M Blue features a Nude Elliptical diamond and split pole pins with a copper wire.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

The 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details compared to the 2M Red model.

2M Blue Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 25 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 2 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Nude Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Blue
• Cartridge weight - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M Blue (interchangeable with 2M Red and 2M Silver)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze, 2M Black and 2M Black LVB 250
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

With the 2M Premounted, it’s never been easier to experience
The 2M Premounted is a practical and elegant solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm. The quality of the SH-4 headshell is sturdy and rigid, yet the design emphasizes a slim and delicate form factor. The strong, lightweight headshell has an ergonomic design with a long finger lift that is easy to pick up.

Features:
- Premounted on our popular SH-4 Black headshell.
- Easy and direct mount on S-shaped tonearms with universal mount.
- Correct Baerwald alignment with tonearms with universal mount.

Bona fide precision with the 2M Bronze
To us hi-fi is more than a fancy label. High fidelity is the goal of everything we do. The 2M Bronze is designed to give the music a whole new dimension of precision. Listening to your records with the 2M Bronze is like hearing them for the first time and you get to fall in love with the songs all over. That is what hi-fi means to us and that is what you get with the 2M Bronze.

Features:
The 2M Bronze features a Nude Fine Line diamond, which is particularly suited for demanding applications. The slim profile of the Fine Line stylus will track even the highest frequency information. Additionally, its larger footprint ensures reduced distortion and record wear. The 2M Bronze uses a special upgraded engine, featuring split pole pins with a silver plated copper wire.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Bronze Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5 mV
• Channel balance at 1 kHz - 1 dB
• Channel separation at 1 kHz - 26 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 + 2 / - 0 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 22 µm/mN
• Stylus type - Nude Fine Line
• Stylus tip radius - r/R 8/40 µm
• Tracking force range - 1.4-1.7 g (14-17 mN)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.2 kOhm
• Internal inductance - 630 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Bronze
• Cartridge weight - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M Bronze (interchangeable with 2M Black and 2M Black LVB 250)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze, 2M Black and 2m Black LVB 250
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

With the 2M Premounted, it’s never been easier to experience
The 2M Premounted is a practical and elegant solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm. The quality of the SH-4 headshell is sturdy and rigid, yet the design emphasizes a slim and delicate form factor. The strong, lightweight headshell has an ergonomic design with a long finger lift that is easy to pick up.

Features:
- Premounted on our popular SH-4 Black headshell.
- Easy and direct mount on S-shaped tonearms with universal mount.
- Correct Baerwald alignment with tonearms with universal mount.

Step into the music with the 2M Red
With the 2M Red you will hear the music come to life on its own terms. It is like taking a step into music itself. This is our entry-level cartridge in the series, but what an entry.

Featues:
The 2M Red features a tipped Elliptical diamond and split pole pins with a copper wire.
The engine provides an increased output of 5.5 mV and an optimized sound reproduction and a high level of sonic accuracy.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Red delivers an open, dynamic sound with a slight touch of warmth.

2M Red Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 22 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 70 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Red
• 2M standard and 2M Verso cartridges weight - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M Red (interchangeable with 2M Blue and 2M Silver)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze, 2M Black and 2M Black LVB 250
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

With the 2M Premounted, it’s never been easier to experience.
The 2M Premounted is a practical and elegant solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm. The quality of the SH-4 headshell is sturdy and rigid, yet the design emphasizes a slim and delicate form factor. The strong, lightweight headshell has an ergonomic design with a long finger lift that is easy to pick up.

Features:
- Premounted on our popular SH-4 Black headshell.
- Easy and direct mount on S-shaped tonearms with universal mount.
- Correct Baerwald alignment with tonearms with universal mount.

2MR: the newest addition to the renowned 2M Series
Ortofon 2MR features a specially designed cartridge housing tailored for turntables and tonearms like Rega matching their requirement for low-form factor cartridges. With its narrow cartridge housing, it seamlessly integrates without a need for modifications or spacers under the tonearm, enabling quick and easy mounting with just two screws. Ortofon 2MR cartridges features unique to Ortofon technologies like: High-performance quad coil motor system with split pole pins, Proprietary Ortofon premium and high-end rubber dampers plus full compatibility with the Ortofon 2M series styli.

Authentic sound reproduction
2MR continues the 2M Series' commitment to authentic sound reproduction.
A high-performance motor system featuring quad coils and split pole pins minimizes eddy current losses, enhancing channel balance and accuracy.
This innovation results in a clean, detailed, and true-to-life sound, faithfully capturing the nuances of your cherished vinyl collection.

More than just a cartridge
2MR cartridge are for those who value an authentic immersive listening experience when listening to their music. 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.
The 2MR maintains the hallmark of interchangeability, allowing you to explore your records in greater depth and detail. The seamless transition between stylus profiles lets you tailor your listening experience, ensuring every note is heard with unparalleled accuracy and emotion. The 2MR series empowers you to explore your records like never before, allowing you to savor every moment of your favorite music.
The 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.

2MR cartridge key features:
• Slimline cartridge body effectively eliminates the need for tonearm spacers, shims or modifications on turntables needing a low form factor cartridge.
• High-performance motor system incorporating unique to Ortofon quad coils with split pole pins, delivering a clean detailed and true-to-life sound.
• 100% compatibility with the 2M styli Ortofon 2MR use the well-known 2M styli.
• Standard half inch mounting quick and easy mounting on the tonearms with just two screws.
• Full range setup 2MR ranges from Mono to Premium: 2MR Red to High-end: 2MR Black LVB 250

Next level authenticity with the 2M Blue
The goal for any cartridge should be to reproduce the sound as close to the artists vision as possible, and the 2M blue takes you further on this journey of authenticity. With the 2M Blue, you get serious about listening to vinyl.

Features:
The 2M Blue features a Nude Elliptical diamond and split pole pins with a copper wire.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

The 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details compared to the 2M Red model.

Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 25 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 2 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Nude Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Blue
• 2MR cartridge weight - 6 g
• 2M and 2M Verso cartridges weight - 7.2 g
• 2M Premounted cartridge weight - 16.7 g

Replacement stylus unit - 2M Blue (interchangeable with 2M Red and 2M Silver)

Stylus lifetime:
with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

2MR: the newest addition to the renowned 2M Series
Ortofon 2MR features a specially designed cartridge housing tailored for turntables and tonearms like Rega matching their requirement for low-form factor cartridges. With its narrow cartridge housing, it seamlessly integrates without a need for modifications or spacers under the tonearm, enabling quick and easy mounting with just two screws. Ortofon 2MR cartridges features unique to Ortofon technologies like: High-performance quad coil motor system with split pole pins, Proprietary Ortofon premium and high-end rubber dampers plus full compatibility with the Ortofon 2M series styli.

Authentic sound reproduction
2MR continues the 2M Series' commitment to authentic sound reproduction.
A high-performance motor system featuring quad coils and split pole pins minimizes eddy current losses, enhancing channel balance and accuracy.
This innovation results in a clean, detailed, and true-to-life sound, faithfully capturing the nuances of your cherished vinyl collection.

More than just a cartridge
2MR cartridge are for those who value an authentic immersive listening experience when listening to their music. 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.
The 2MR maintains the hallmark of interchangeability, allowing you to explore your records in greater depth and detail. The seamless transition between stylus profiles lets you tailor your listening experience, ensuring every note is heard with unparalleled accuracy and emotion. The 2MR series empowers you to explore your records like never before, allowing you to savor every moment of your favorite music.
The 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.

2MR cartridge key features:
• Slimline cartridge body effectively eliminates the need for tonearm spacers, shims or modifications on turntables needing a low form factor cartridge.
• High-performance motor system incorporating unique to Ortofon quad coils with split pole pins, delivering a clean detailed and true-to-life sound.
• 100% compatibility with the 2M styli Ortofon 2MR use the well-known 2M styli.
• Standard half inch mounting quick and easy mounting on the tonearms with just two screws.
• Full range setup 2MR ranges from Mono to Premium: 2MR Red to High-end: 2MR Black LVB 250

Bona fide precision with the 2M Bronze
To us hi-fi is more than a fancy label. High fidelity is the goal of everything we do. The 2M Bronze is designed to give the music a whole new dimension of precision. Listening to your records with the 2M Bronze is like hearing them for the first time and you get to fall in love with the songs all over. That is what hi-fi means to us and that is what you get with the 2M Bronze.

Features:
The 2M Bronze features a Nude Fine Line diamond, which is particularly suited for demanding applications. The slim profile of the Fine Line stylus will track even the highest frequency information. Additionally, its larger footprint ensures reduced distortion and record wear. The 2M Bronze uses a special upgraded engine, featuring split pole pins with a silver plated copper wire.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5 mV
• Channel balance at 1 kHz - 1 dB
• Channel separation at 1 kHz - 26 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 + 2 / - 0 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 22 µm/mN
• Stylus type - Nude Fine Line
• Stylus tip radius - r/R 8/40 µm
• Tracking force range - 1.4-1.7 g (14-17 mN)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.2 kOhm
• Internal inductance - 630 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Bronze
• 2MR cartridge weight - 6 g
• 2M and 2M Verso cartridges weight - 7.2 g
• 2M Premounted cartridge weight - 16.7 g

Replacement stylus unit - 2M Bronze (interchangeable with 2M Black and 2M Black LVB 250)

Stylus lifetime:
with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

2MR: the newest addition to the renowned 2M Series
Ortofon 2MR features a specially designed cartridge housing tailored for turntables and tonearms like Rega matching their requirement for low-form factor cartridges. With its narrow cartridge housing, it seamlessly integrates without a need for modifications or spacers under the tonearm, enabling quick and easy mounting with just two screws. Ortofon 2MR cartridges features unique to Ortofon technologies like: High-performance quad coil motor system with split pole pins, Proprietary Ortofon premium and high-end rubber dampers plus full compatibility with the Ortofon 2M series styli.

Authentic sound reproduction
2MR continues the 2M Series' commitment to authentic sound reproduction.
A high-performance motor system featuring quad coils and split pole pins minimizes eddy current losses, enhancing channel balance and accuracy.
This innovation results in a clean, detailed, and true-to-life sound, faithfully capturing the nuances of your cherished vinyl collection.

More than just a cartridge
2MR cartridge are for those who value an authentic immersive listening experience when listening to their music. 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.
The 2MR maintains the hallmark of interchangeability, allowing you to explore your records in greater depth and detail. The seamless transition between stylus profiles lets you tailor your listening experience, ensuring every note is heard with unparalleled accuracy and emotion. The 2MR series empowers you to explore your records like never before, allowing you to savor every moment of your favorite music.
The 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.

2MR cartridge key features:
• Slimline cartridge body effectively eliminates the need for tonearm spacers, shims or modifications on turntables needing a low form factor cartridge.
• High-performance motor system incorporating unique to Ortofon quad coils with split pole pins, delivering a clean detailed and true-to-life sound.
• 100% compatibility with the 2M styli Ortofon 2MR use the well-known 2M styli.
• Standard half inch mounting quick and easy mounting on the tonearms with just two screws.
• Full range setup 2MR ranges from Mono to Premium: 2MR Red to High-end: 2MR Black LVB 250

Step into the music with the 2M Red
With the 2M Red you will hear the music come to life on its own terms. It is like taking a step into music itself. This is our entry-level cartridge in the series, but what an entry.

Featues:
The 2M Red features a tipped Elliptical diamond and split pole pins with a copper wire.
The engine provides an increased output of 5.5 mV and an optimized sound reproduction and a high level of sonic accuracy.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Red delivers an open, dynamic sound with a slight touch of warmth.

Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 22 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 70 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Red
• 2MR cartridge weight - 6 g
• 2M and 2M Verso cartridges weight - 7.2 g
• 2M Premounted cartridge weight - 16.7 g

Replacement stylus unit - 2M Red (interchangeable with 2M Blue and 2M Silver)

Stylus lifetime:
with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

High quality 12" professional grade slipmat. Ideal for scratching and turntablists. Provides durability and will not scuff or damage vinyl.

• Made out of a smooth but strong material
• Unique matte surface
• Far more resistant to dust and other particles
• Extra thin and provide optimum feel for DJs
• Comes in pairs packaged inside a sleeve

Awesome logo design developed in collaboration with DJ ND and Maxime Bouchat, Graphic Designer, Blue Marine Productions Associées.

High quality 12" professional grade slipmat. Ideal for scratching and turntablists. Provides durability and will not scuff or damage vinyl.

• Made out of a smooth but strong material
• Unique matte surface
• Far more resistant to dust and other particles
• Extra thin and provide optimum feel for DJs
• Comes in pairs packaged inside a sleeve

Awesome logo design developed in collaboration with DJ ND and Maxime Bouchat, Graphic Designer, Blue Marine Productions Associées.

Comprises 1 PC carbon fibre stylus brush and 1 PC screwdriver in a plastic cylinder.

High quality 12" professional grade slipmat. Ideal for scratching and turntablists. Provides durability and will not scuff or damage vinyl.

• Made out of a smooth but strong material
• Unique matte surface
• Far more resistant to dust and other particles
• Extra thin and provide optimum feel for DJs
• Comes in pairs packaged inside a sleeve

Awesome 3D design
The VNL 3D design is developed in collaboration with DJ ND and Maxime Bouchat, Graphic Designer, Blue Marine Productions Associées.

The slipmat design uses several elements linked to the DJ culture:
• Scissors stand for "Cutting sounds"
• Equalizer levels picture refers to the mixers' levels
• Spiral symbolises turntable platter when spinning

The effect of animation is fully obtainable when the pitch is set to 33 +8.

The LH-2000 is a basic high quality headshell designed specifically for HiFi applications. Providing a clean, minimalist aesthetic, the LH-2000 is great for a wide variety of cartridges, e.g. the 2M Series .

Knowing the fundamental headshell dimensions will in a lot of cases make it easier to mount and align cartridge and tonearm correctly. Please scroll to the bottom of the page to see the headshells mounting dimensions chart.

The LH-2000 comes with leadwires for easy and convenient connection
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell.

Please remember correct orientation of the leads. Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is only 1.0 mm.

Features and Technical data:
• Universal mount
• Solid aluminum build
• Weight without screws - 15.5 grams
• Mounting distance - min 35.3 mm, max 43.4 mm
• Headshell length - 50.3 mm
• Headshell width - 20.0 mm

The LH-4000 is a basic high quality headshell designed specifically for HiFi applications. Providing a clean, minimalist aesthetic, the LH-4000 is great for a wide variety of cartridges, specially recommended for the MC Quintet series.

Special features:
• Azimuth adjustable, which is beneficial for optimal channel separation
• Ergonomic fingerlift for easy handling
• Knowing the fundamental headshell dimensions will in a lot of cases make it easier to mount and align cartridge and tonearm correctly. Please scroll to the bottom of the page to see the headshells mounting dimensions chart.

The LH-4000 comes with leadwires for easy and convenient connection
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell.

Please remember correct orientation of the leads. Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is only 1.0 mm.

Features and Technical data:
• Universal mount
• Solid aluminum build
• Azimuth adjustable by means of hexagon wrench
• PIN conductor - Gold plated
• Weight - 14.3 grams without screws
• Mounting distance min. - 39.5 mm
• Mounting distance max. - 45.6 mm
• Headshell length - 51.9 mm
• Headshell width - 19.1 mm

Luxury leadwireset
LW-6N is the 6N lead wire made of Ultra High Purity Copper wire.
The configuration is very sofisticated with different diameter of wire strand, the inside strand is right windings, the outside strand is left winding. The end of wire is fastened by gold plated terminal.
The tight winding against each other makes the clear transmission of music signals. Clear and crisp tonality.

Technical data:
• High purity Cu wire 6NCu: 7 x φ 0.18mm (Right strands)
• High purity Cu wire 6NCu: 17 x φ 0.10mm (Left strands)

Mounting instructions:
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell. Please remember correct orientation of the leads. Ortofon SH-4 headshell and Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is normally only 1.0 mm.

Using LW 6N with the SH-4 headshell requies the LW 6N shell side clamp to be widened a little bit to fit on the SH-4 PINs. If shifted around, it may cause over-tightening of the assembly. Being aware about this detail, you will avoid the risk of having the cartridge's terminal PINs fall out.

Luxury leadwireset
LW-7N is the hybrid lead wire made of Ultra High Purity Copper wire of 7N and 6 N. The end of wire is fastened by Rhodium plated terminal.
As there is no foreign particle other than Copper 7N (99.99999 % purity) in the wire, music signal can be transmitted without any noise.

Technical data:
• High purity Cu wire 7NCu: 3 x φ 0.26mm
• High purity Cu wire 6NCu: 16 x φ0.10mm

Mounting instructions:
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell. Please remember correct orientation of the leads. Ortofon SH-4 headshell and Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is normally only 1.0 mm.

Using LW 7N with the SH-4 headshell requies the LW 7N shell side clamp to be widened a little bit to fit on the SH-4 PINs. If shifted around, it may cause over-tightening of the assembly. Being aware about this detail, you will avoid the risk of having the cartridge's terminal PINs fall out.

LW-800S is the most sophisticated lead wires composed of Pure Silver and Silver coated wire.
The end of wire is fastened by Rhodium plated terminal.
Since Silver has the best electrical conductive properties of all the metals, the LW-800S silver wire is able to transmits the very clear high tone signals, which brings the brilliant tonality to the sound reproduction.

Technical data:
• 4N Pure Silver wire: 3 x φ 0.26mm
• Silver plated Oxygen Free Copper (OFC) wire: 16 x φ0.10mm

Mounting instructions:
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell. Please remember correct orientation of the leads. Ortofon SH-4 headshell and Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is normally only 1.0 mm.

Using LW 8N with the SH-4 headshell requies the LW 8N shell side clamp to be widened a little bit to fit on the SH-4 PINs. If shifted around, it may cause over-tightening of the assembly. Being aware about this detail, you will avoid the risk of having the cartridge's terminal PINs fall out.

Enter the Exclusive world of Ortofon’s famous moving coil sound!
The Quintet Red is a perfect introduction to the world of Ortofon moving coils.
It features an Elliptical diamond which is cut and polished to Ortofon’s standards.

This entry-level MC cartridge has very high price-to-performance ratio and is a perfect all-rounder for the newcomers to the world of Moving Coil cartridges.

MC Quintet Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth.

The ST-7 transformer is a perfect match for the MC Quintet Red cartridge.

LH-4000 headshell is specially recommended for MC Quintet cartridges series.

MC Quintet Red Technical data:
• Output voltage at 1 kHz 5 cm/sec - 0.5 mV
• Channel balance - < 1.5 dB
• Channel separation at 1 kHz - > 21 dB
• Channel separation at 15 kHz - > 14 dB
• Frequency response 20-20.000 Hz - +/-2.5 dB
• Tracking ability at 315 Hz at recommended tracking force *) - 65 μm
• Compliance, dynamic, lateral - 15 μm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 μm
• Tracking force range - 2.1-2.5 g (21-25 mN)
• Tracking force recommended - 2.3 g (23 mN)
• Tracking angle - 20º
• Internal impedance, DC resistance - 7 Ohm
• Recommended load impedance - >20 Ohm
• Cartridge body material - ABS/Aluminium
• Coil wire material - Copper
• Cartridge colour - Red
• Cartridge weight - 9 g
*) Typical value

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for Quintet cartridge.

Ease of use
Top-mounting of the Quintet cartridges is easy and secure using the screws supplied. The aluminuim frame has threaded mounting holes and is fitted easily with the 5mm or 7mm screws depending on the thickness of the headshell.

The Quintet series’ right angles, straight lines, stylus visibility and ample distance between the record surface and the cartridge’s bottom will make it easy to mount and align the cartridge and tonearm correctly. The Quintet Series gives excellent results with most common tonearms.

Optimal fit and sound reproduction
If your tonearm has a standard headshell or a cartridge mount, then step up to optimal sound reproduction with OM’s. A glance at anyone of these cartridges will reveal Ortofon's answer to perfect tonearm matching. Ingeniously tucked into the top of the mounting bracket is a tiny, removable weight-plate.

If your tonearm is an standard tonearm, just leave the weight-plate. If your tonearm is one of the low mass types, then simply remove the weight. The mass of your OM cartridge is now a mere 2.5g.

OM 5E features Elliptical stylus that provides balanced and distortion-free playback. Elliptical diamonds are able to follow the groove oscillations more accurately than spherical diamonds due to their contoured shape. This results in better tracking and less distortion.

• OM 5E Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4 mV
• Channel balance at 1 kHz - 2 dB
• Channel separation at 1 kHz - 22 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 3 / -3
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17.5 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 750 Ohm
• Internal inductance - 450 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 200-500 pF
• Cartridge colour, body/stylus - Black/Black
• Cartridge weight incl. extra weight - 5 g
• Cartridge weight excl. extra weight - 2.5 g
• Replacement stylus unit - Stylus 5E
*) Typical value

Styli types and interchangeability
By adopting a wide range of replacement styli, the OM 5 Series can provide an optimum match for your home system, application and budget.
In the development of OM cartridges, a major objective was to provide the music lover with the opportunity to optimize sound reproduction without having to replace the entire cartridge. Instead of being merely intended for replacement purposes following wear or damage, the OM 5 Series allows you to step up to better sound by simply upgrading the stylus. Depending on your preference, styli for the OM 5 Series are easily interchanged and include: styli 3E, 5E, 10, 20, 30, 40 & 78 and D 25 M.

The OM 5S is a moving magnet cartridge for general purpose application
If your tonearm has a standard headshell or a cartridge mount, then step up to optimal sound reproduction with OM’s. A glance at anyone of these cartridges will reveal Ortofon's answer to perfect tonearm matching. Ingeniously tucked into the top of the mounting bracket is a tiny, removable weight-plate.

If your tonearm is an standard tonearm, just leave the weight-plate. If your tonearm is one of the low mass types, then simply remove the weight. The mass of your OM cartridge is now a mere 2.5 g.

The OM 5S features Spherical stylus, robust and economic solution for play back of vinyl records.

For more than 50 years, Ortofon has been designing and manufacturing Moving Magnet cartridges. Along with our well-regarded Moving Coil cartridges, Moving Magnet models have established a good reputation among music lovers and Hi-Fi enthusiasts the world over.

The new Ortofon OM 5 series encompasses three basic cartridges: OM 5S, OM 5E and Super OM 5E.
• The series is the lowest-mass range of moving magnet cartridges offered by Ortofon.
• The OM cartridges bodies have been designed to provide easy mounting and alignment on both top mount and bottom mount headshells.
• The OM 5 Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

OM 5S Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4.5 mV
• Channel balance at 1 kHz - 2 dB
• Channel separation at 1 kHz - 20 dB
• Channel separation at 15 kHz - 12 dB
• Frequency response - 20-22.000 Hz
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Spherical
• Stylus tip radius - R 18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17.5 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 750 Ohm
• Internal inductance - 450 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 200-500 pF
• Cartridge colour, body/stylus - Black/Black
• Cartridge weight incl. extra weight - 5 g
• Cartridge weight excl. extra weight - 2.5 g
• Replacement stylus unit - Stylus 5S
*) Typical value

Styli types and interchangeability
By adopting a wide range of replacement styli, the OM 5 Series can provide an optimum match for your home system, application and budget.
In the development of OM cartridges, a major objective was to provide the music lover with the opportunity to optimize sound reproduction without having to replace the entire cartridge. Instead of being merely intended for replacement purposes following wear or damage, the OM 5 Series allows you to step up to better sound by simply upgrading the stylus. Depending on your preference, styli for the OM 5 Series are easily interchanged and include: styli 3E, 5E, 10, 20, 30, 40 & 78 and D 25 M.

Tool for OM mounting

The new Ortofon Reference Interconnect cables Series is designed and manufactured by Ortofon Japan
Each of the new Reference series cables has its individual sonic expression:

- The Reference Red is an all-purpose, decent, but not too expensive cable that would be a great addition to any audio equipment. The sound is relaxed, warm and dynamic with high resolution.
- The Reference Blue is a dynamic and high-resolution cable that reveals detailed reproduction throughout the spectrum.
- The Reference Bronze has an astonishing wide-range, clear and neutral sound.
- The Reference Black is a new generation reference audio cable par excellence with a well-balanced, neutral and precise sound.

Ortofon Reference Red cable
The Reference Red Interconnect cable is a perfect combination of 4N OFC (Oxygen-free copper) and 4N HiFC (High performance pure copper) conductors. These two copper conductor materials are combined to create a warm, dynamic sound with high resolution.
The Reference Red is surrounded by shield of both 16 sets of 0.1mm x 10 copper wires and aluminum to reduce electromagnetic induced noise.
The gold plated RCA terminals provide easy, stable and durable connection.

• Cable capacity: 190pF/m
• Cable length: 1.0 m or 1.5 m
• Terminal type: RCA
• 2 pieces per set

Reference Red technical configuration
① Signal conductors:
• OFC (Oxygen-free copper) Ø 0.5 mm + Ø 0.32 mm × 7
• HiFC (High performance pure copper) Ø 0.12 mm × 28
② Signal conductors:
• OFC (Oxygen-free copper) Ø 0.5 mm + Ø 0.32 mm × 7
• HiFC (High performance pure copper) Ø 0.12 mm × 28
③ Damping material: Cotton fiber
④ Shield: Aluminuim tape
⑤ Shield: Braided Tin-plated 3N copper wire Ø 0.1 mm × 10 × 16
⑥ Insulation: Halogen-free highly resilient elastomer
⑦ Cable diameter: 7.5 mm
⑧ Insulation: PE

Screws for mounting 2M cartridges on the headshell incl.:
• 2x 2.5x5mm
• 2x 2.5x7mm

Ortofon SH-4 headshells are high-quality, solid headshells for variety of applications

The SH-4 headshell has an ergonomic design with a long finger that is easy to pick-up. The big finger grip and shorter construction makes movement and placement of the headshell easy and visible.
The wire terminals on the rear side are also gold plated for better signal transmission.

Dimensions and weight:
• Weight: 9.4g
• Shell length: 51.5mm
• Finger Length: 27mm

The SH-4 comes with leadwires for easy and convenient connection
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell.

Ortofon SH-4 headshell PINs and Ortofon cartridges' terminal PINs diameter is 1.2 mm. Leadwires supplied fit all right on the cartridges' terminal PINs.

Technical specifications:
• Frequency response: - 20-20.000 Hz + 2 / - 2 dB
• Tracking ability at 315Hz at recommended tracking force*): 70 µm
• Compliance, dynamic, lateral: 25 µm/mN
• Stylus type: Elliptical
• Stylus tip radius: r/R 8/18 µm
• Tracking force range: 1.0-1.5 g (10-15 mN)
• Tracking force, recommended: 1.25 g (12.5 mN)
• Tracking angle: 20°
• Stylus colour: Black
• Recommended for TM 14U
*) Typical value

Technical specifications:
• Frequency response - 20-20.000 Hz + 2 / - 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 70 µm
• Compliance, dynamic, lateral - 25 µm/mN
• Stylus type - Nude Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.25-1.75 g (12.5-17.5 mN)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Stylus colour - Black
• Recommended for following cartridges: Super OM 20, OM 20, OMP 20, OMB 20, LM 20, Concorde 20, LM 20H, TM 20U, TM 20H
*) Typical value

Technical specifications:
• Frequency response - 20-20.000 Hz + 2 / - 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Spherical
• Stylus tip radius - R 18 µm
• Tracking force range - 1.25-1.75 g (12.5-17.5 mN)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Stylus colour - Grey
• Recommended for Series 305 Universal
*) Typical value

Technical specifications:
• Frequency response - 20-20.000 Hz + 3 /- 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.25-1.75 г (12.5-17.5 мН)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Stylus colour - Grey
• Recommended for Series 310 Universal
*) Typical value

Technical specifications:
• Frequency response - 20-18.000 Hz + 2 / - 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17.5 mN)
• Tracking angle - 20°
• Stylus colour - Black
• Recommended for OM 3E, OMP 3E, OMB 3E
*) Typical value

Technical specifications:
• Frequency response - 20-20.000 Hz + 3 /- 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.25-1.75 g (12.5-17.5 mN)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Stylus colour - Black
• Recommended for Series 500 Mkll, 510, 510 P, Alfa
*) Typical value

Technical specifications:
• Frequency response - 20-20.000 Hz + 2 / - 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Spherical
• Stylus tip radius - R 18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17,5 mN)
• Tracking angle - 20°
• Stylus colour - Black
• Recommended for OM 5S and OM 1S
*) Typical value

Technical specifications:
• Frequency response: 20-18.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force *): 60 µm
• Compliance, dynamic, lateral: 25 µm/mN
• Stylus type: Elliptical
• Stylus tip radius: r/R 8/18 µm
• Tracking force range: 1.0-1.5 g (10-15 mN)
• Tracking force, recommended: 1.25 g (12.5 mN)
• Tracking angle: 20°
• Stylus colour: Black
• Recommended for TM 7 and TM 7U cartridges models
*) Typical value

Technical specifications:
• Frequency response - 20-12.000 Hz + 2 / - 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 15 µm/mN
• Stylus type - Spherical
• Stylus tip radius - 65µm
• Tracking force range - 1.75-2.25 g (17.5-22.5 mN)
• Tracking force, recommended - 2.0 g (20 mN)
• Tracking angle - 20°
• Stylus colour - Black
• Recommended for following cartridges: all Super OM, OM, OMB, OMP, TM, Concorde STD cartridges for playing 78 r.p.m. records
*) Typical value

Technical specifications:
• Frequency response - 20-18.000 Hz + 2 / - 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 70 µm
• Compliance, dynamic, lateral - 7 µm/mN
• Stylus type - Spherical
• Stylus tip radius - R 25µm
• Tracking force range - 2.0-3.0 g (20-30 mN)
• Tracking force, recommended - 2.5 g (25 mN)
• Tracking angle - 20°
• Stylus colour - Black
• Recommended for following cartridges: all Super OM, OM, OMP, TM, Concorde cartridges for playing micro-groove records.
*) Typical value

Stylus guard (1 Pcs.)

Styli protection caps for VNL cartridges and styli

The stylus protection guard helps to limit stylus damage, if the cartridge accidentally slides across a record or if the cartridge is dropped onto the record.

The protection caps come in pairs.

The Super OM 5E major improvements:
1. By means of computer simulations it has been possible to define the natural pivot point of the system with unprecedented accuracy while achieving an optimum oscillation balance. The result: improved linearity, higher channel separation and reduced distortion.

2. OM Super cartridges models have split pole PINs which reduces magnetic losses at the treble end. This technology extends the frequency range and improves phase linearity.

3. OM Super 5 cartridge body is manufactured from a Noryl (plastic & glass compound) which ensures high rigidity and freedom from resonances.

Optimal fit and sound reproduction
If your tonearm has a standard headshell or a cartridge mount, then step up to optimal sound reproduction with OM’s. A glance at anyone of these cartridges will reveal Ortofon's answer to perfect tonearm matching. Ingeniously tucked into the top of the mounting bracket is a tiny, removable weight-plate.

If your tonearm is an standard tonearm, just leave the weight-plate. If your tonearm is one of the low mass types, then simply remove the weight. The mass of your OM cartridge is now a mere 2.5g.

Super OM 5E features Elliptical stylus that provides balanced and distortion-free playback. Elliptical diamonds are able to follow the groove oscillations more accurately than spherical diamonds due to their contoured shape. This results in better tracking and less distortion.

Super OM 5 Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 22 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 3 / -3
• Tracking ability at 315Hz at recommended tracking force - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17.5 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1 kOhm
• Internal inductance - 580 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 200-500 pF
• Cartridge colour, body/stylus - Black/Black
• Cartridge weight incl. extra weight - 5 g
• Cartridge weight excl. extra weight - 2.5 g
• Replacement stylus unit - Stylus 5 E, Stylus 10

Styli types and interchangeability
The OM 5s features a Spherical diamond. Spherical diamonds are the simplest and most robust diamonds. The OM 5E and Super OM 5E feature an Elliptical diamond.

In the development of OM cartridges, a major objective was to provide the music lover with the opportunity to optimize sound reproduction without having to replace the entire cartridge. Instead of being merely intended for replacement purposes following wear or damage, the OM 5 Series allows you to step up to better sound by simply upgrading the stylus.

Depending on your preference, styli for the OM 5 Series are easily interchanged and include: styli 3E, 5E, 10, 20, 30, 40 & 78 and D 25 M.

The new Ortofon OM 5 series encompasses three basic cartridges: OM 5S, OM 5E and Super OM 5E.
• The series is the lowest-mass range of moving magnet cartridges offered by Ortofon.
• The OM cartridges bodies have been designed to provide easy mounting and alignment on both top mount and bottom mount headshells.
• The OM 5 Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

High quality 12" professional grade slipmat. Ideal for scratching and turntablists. Provides durability and will not scuff or damage vinyl.

• Made out of a smooth but strong material
• Unique matte surface
• Far more resistant to dust and other particles
• Extra thin and provide optimum feel for DJs
• Comes in pairs packaged inside a sleeve

Awesome logo design developed in collaboration with DJ ND and Maxime Bouchat, Graphic Designer, Blue Marine Productions Associées.

Lightweight 45" bag holds about 50 of your favorite PPU singles.

Lightweight 45" bag holds about 50 of your favorite PPU singles.

With our practical index, you can finally bring order to your vinyl collection. No matter how big your collection is - with the separating register you can keep an overview. The 13 wooden registers are printed alphabetically and are simply inserted between the records.
The indexes are 2.5 mm thick, 36 cm high and 6 cm wide, printed on both ends and made of high-quality plywood. They can be used vertically and horizontally.
As part of the Vinyl Care by HHV product range, the record dividers were developed for passionate vinyl collectors who are looking for simple and high-quality utensils for the care and storage of their records.

After the Debut Carbon EVO revolutionized the Debut series in 2020, the Debut PRO raises the bar even higher.

A MILESTONE FOR THE NEXT DECADES
The Debut PRO brings an absolutely new design to Pro-Ject turntables. The audiophile turntable is convincing in all respects – not only visually, but more importantly also in terms of sound.
The precision CNC milled parts are optically perfectly coordinated and lead the Debut PRO to its modern simple, elegant and unprecedented design. The nickel finish of all these aluminium components result in a hard, resistant surface. This process enables us to produce very high-quality and sustainable components and avoid plastics and similar materials that continue to age over time and would more importantly also degrade sound quality.

The tonearm bearing is a completely new design. Precision CNC'd out of a single block of aluminium, you can see all the production stages above. The last step is putting a nickel finish on it. This will increase the rigidity of the bearing, ensuring free and fluid movement of the tonearm and precise tracking without material degration in looks or function.

DEEPLY DRIVEN
The electronically regulated synchronous motor drives the platter and guarantees the most accurate and stable speeds. Change between them easily with the toggle switch. With the supplied round belt for 78 rpm you can also listen to your shellac records.

A NEW PLATTER – A DEEPPER DISH
The new Debut PRO platter is a first on any Pro-Ject turntable. It features a notch for the record label and together with our Record Puck PRO (available separately) the puck's weight will press your record tightly against the platter. The die-cast aluminium platter is reworked and precision balanced in an extra step to obtain an evenly spinning platter. It is anti-magnetic, allowing MC cartridges to work properly. Delve deep into the vast upgrade path the Debut PRO has to offer!
The anti-magnetic heavy aluminium platter has a ring made of TPE (thermoplastic elastomer) on the inside that helps to dampen all resonances and minimizes wow and flutter. Our seperately available Record Puck PRO provides an extra level of damping and stability, so it is the perfect add-on for the Debut PRO.

HYBRID TONEARM
The new Debut PRO features a one-piece carbon-aluminium sandwich tonearm. The carbon layer gives the tonearm a high degree of rigidity, while the inner aluminium tube takes over the damping of the tonearm. This makes the tonearm perfect to be upgraded with higher-end MC cartridges!

AZIMUTH & VTA ADJUSTMENT
The newly designed tonearm base allows you to adjust both the azimuth and the vertical tracking angle (VTA). The tonearm height can be continuously adjusted by loosening the two grub screws. These settings give you the option of adapting the tonearm to height changes allowing the use of different turntable mats or other cartridges to always achieve the best sound quality. Setting and experimenting with the VTA & Azimuth is crucial in extracting every last bit of performance out of your cartridges.

Features:
Pick it PRO
Lively and robust sound
The perfect combination of components is the key to achieve the great sound of the Pick it PRO.

Nickel Coating
Sustainable components
The nickel finish of the aluminium components results in a hard, resistant surface.

Hybrid Tonearm
Carbon Aluminium Sandwich
This super stiff and uniquely dampened tonearm ensures perfect tracking of the record groove.

VTA & Azimuth
Fully adjustable
The Debut PRO comes with fully adjustable Azimuth & VTA. It offers you the possibility to modify your turntable as you want it.

33/45/78 RPM
High precision motor control
The playback speeds are electronically controlled with precision, which guarantees the most accurate and stable music reproduction. Change between speeds easily with the toggle switch.

Bearing block
Complete new design
The precision CNC milled and nickel coated tonearm bearing parts are completely new and designed just for the PRO.

Special Platter
TPE damped & anti magnetic
The heavy aluminium platter has a ring made of TPE (thermoplastic elastomer) on the inside that helps to dampen all resonances and minimizes wow and flutter.

Metal Feet
Damped & height adjustable
The three height adjustable damped aluminium feet guarantee the perfect stand & massively reduce risk of acoustical feedback.

Technical Specifications:
• Speed: 33, 45/(78) (electronic speed change)
• Drive principle: belt drive with electronic speed control
• Platter: 300mm, die cast aluminium platter with TPE damping and felt mat
• Platter bearing: high precision stainless steel axle in bronze bushing
• Wow & flutter: 33: +/-0,16%; 45: +/-0,14%
• Speed drift: 33: +/-0,40%; 45: +/-0,50%
• Signal to noise: 68dB
• Tonearm: 8,6” one-piece carbon-aluminium tonearm
• Effective arm length/mass: 218,5 mm / 10,0 g
• Overhang: 18,5mm
• Included accessories: 15V DC / 0,8A power supply, dust cover, 78 RPM round belt, 7‘‘ single adapter
• Power consumption: 4W / 0W standby
• Dimensions: 415 x 113 x 320mm (WxHxD)
• Weight: 6 kg net

Manual: https://www.project-audio.com/wp-content/uploads/2021/07/PJ-Phono-DebutPro-Manual.pdf

2-way bookshelf speakers

And these are comments from audio testers:
• Well tuned and upbeat basslines
• Lively dynamics
• Surprisingly low coloration
• Good transparency and reasonable image depth
• Bass is fast and tuneful, this is what really matters!

Scope of delivery:
• 2x Speaker Box 5
• 2x speaker grill black
• 1x pair of gloves

Features:
• Audiophile bass-reflex design
• Gold-plated speaker terminal (single-wired)
• Simple Wall-mount included
• Magnetically shielded
• Front cover with magnetic attachment
• Speaker-Box Wall Bracket available as an option

Technical Specifications:
• Sensitivity (1W/1m): 86 dB
• Recommended amplifier power: 10 to 150 watts
• Tweeter: 25 mm Ø silk-dome Neodymium magnet
• Woofer: 130 mm Ø fiberglass cone
• Frequency response: 55 Hz - 20 kHz
• Impedance: 4 - 8 Ohms
• Dimensions: W x H x D 160 x 255 x 210 mm
• Weight: 4.2 kg

Eco-friendly record cleaning concentrate for VC-S, VC-E & VC-S2

The ultimate eco-friendly record cleaning concentrate

This new cleaning formula was developed exclusively by Pro-Ject Audio Systems. It does not contain alcohol, which may harm record surfaces. Wash it contains only high-purity components, which are 100% eco-friendly, non-toxic and non-flammable. Wash it is the first solution to clean vinyls & shellac records gentle, but efficiently. Wash it will evaporate without leaving residues on the record surface!

250 ml (will clean about 337 records)

Features
•New highly concentrated cleaning formula by Pro-Ject
•Wash it cleans vinyl records & shellacs
•Wash it contains only high-purity components
•Eco-friendly - Non-toxic - Non-flammable
•Record looks like new after washing
•Dissolves a wide range of impurities including fat/grease
•For very dirty records repeat the cleaning process
•Evaporates quickly and leaves zero residues
•Optimum mix ratio 1:10 to 1:20 with distilled/demineralized water - do not use tap water!
•Optimum application temperature 20 - 40 degrees (mixing ratio for warmed Wash it is 1:20)
•Optimum storage temperature 10 - 25 degrees

The R.A. The Rugged Man Logo Slipmat is made from lightweight felt and equipped with a fresh graphic that bigs up the latest albums by R.A. The Rugged Man. Style meets function to the highest degree.

The RECORD BOX record tower is an innovative set of two record boxes and a register box, which are connected by means of practical adhesive points. In total, the record tower offers space for the storage and presentation of a maximum of 310 12'' records.

Ideal for DJs, record stores and the home record collection: The register box is the top component of the tower and gives you direct access to your most important records, which you can easily browse through. The stacked record boxes prove to be a space-saving storage option that keeps things tidy and organized.

Easy assembly and creative freedom: The set of three record boxes is part of RECORD BOX's unique furniture system, which allows you to make creative additions that perfectly suit your needs. The assembly is very easy, the connection is made with the non-slip glue dots, which were developed especially for this system.

Clever solutions for your individual needs: The Record Tower is available in white, grey and black. Buying the set offers you a saving compared to buying the boxes individually and gives you all the design freedom you need for your record furniture. The boxes are made of 15 mm MDF with melamine and offer you a lot of stability as well as a clear look at an excellent price-performance ratio.

Features:

• Record tower as a combination of two 12-inch 110 storage boxes and one 12-inch 100 storage register box
• Connection through non-slip silicone adhesive dots
• Favorable bundle price compared to single purchase
• Available in white, grey and black
• Space for more than 300 LPs
• Ideal for DJs, record stores, the home record collection
• Can be combined in many ways with the other products in the RECORD-BOX furniture series
• Boxes for self-assembly - screwdriver required!

Technical data:

• Material: MDF wood (15 mm) with melamine coating.
• Dimensions: approx. 36 x 36 x approx. 104 cm
• 1x 12-inch 100 storage boxes
• 2x 12-Inch 110 Storage Boxes
• 1x adhesive dots from RECORD BOX
• assembly instructions
• Weight: 12,7 kg

The RECORD BOX record tower is an innovative set of two record boxes and a register box, which are connected by means of practical adhesive points. In total, the record tower offers space for the storage and presentation of a maximum of 310 12'' records.

Ideal for DJs, record stores and the home record collection: The register box is the top component of the tower and gives you direct access to your most important records, which you can easily browse through. The stacked record boxes prove to be a space-saving storage option that keeps things tidy and organized.

Easy assembly and creative freedom: The set of three record boxes is part of RECORD BOX's unique furniture system, which allows you to make creative additions that perfectly suit your needs. The assembly is very easy, the connection is made with the non-slip glue dots, which were developed especially for this system.

Clever solutions for your individual needs: The Record Tower is available in white, grey and black. Buying the set offers you a saving compared to buying the boxes individually and gives you all the design freedom you need for your record furniture. The boxes are made of 15 mm MDF with melamine and offer you a lot of stability as well as a clear look at an excellent price-performance ratio.

Features:

• Record tower as a combination of two 12-inch 110 storage boxes and one 12-inch 100 storage register box
• Connection through non-slip silicone adhesive dots
• Favorable bundle price compared to single purchase
• Available in white, grey and black
• Space for more than 300 LPs
• Ideal for DJs, record stores, the home record collection
• Can be combined in many ways with the other products in the RECORD-BOX furniture series
• Boxes for self-assembly - screwdriver required!

Technical data:

• Material: MDF wood (15 mm) with melamine coating.
• Dimensions: approx. 36 x 36 x approx. 104 cm
• 1x 12-inch 100 storage boxes
• 2x 12-Inch 110 Storage Boxes
• 1x adhesive dots from RECORD BOX
• assembly instructions
• Weight: 12,7 kg

The cleaning roller offers you a time-saving and effective way to clean your records. Dust and dirt simply stick to the silicone surface of the roller. It is very easy to use: Carefully place the record on a clean, soft surface such as the Record Cleaning Work Mat from the HHV Vinyl Care series. Hold the cleaning roller by the handle and place the silicone roller on the record. Carefully roll over the entire surface of the record, changing direction several times.
To remove dust and dirt from the Record Cleaning Roller, wash it with lukewarm soapy water. Allow it to dry completely before using it again and store it in the storage box provided. Sunlight and chemical cleaning agents damage the roller and should therefore be avoided at all costs.
As part of the Vinyl Care series from HHV, we have developed the record cleaning roller especially for the needs of vinyl collectors. We incorporate the experience of our customers directly into product development.

To clean your vinyl records thoroughly, it is important to place them on a soft, dirt-free surface. With the cleaning mat for vinyl records, HHV has created a solution that makes caring for your vinyl even easier.
Place the record in the middle of the cleaning mat and use Vinyl Care products such as the practical cleaning roller to remove dust and dirt from your vinyl. CDs or DVDs can easily be placed in the corner of the mat. The use of a plastic adapter is recommended for cleaning 7-inch records.
All Vinyl Care by HHV products are developed with direct feedback from our customers and offer innovative solutions for the care and storage of vinyl records.

RELOOP FLUX - 6X6 IN/OUT USB-C DVS INTERFACE FOR SERATO DJ PRO

We are excited to introduce the Reloop Flux: A next-generation 6x6 In/out USB-C DVS Interface for Serato DJ Pro. It can transform any conventional mixer into a professional digital vinyl system.

BACK TO THE MUSIC
The Reloop Flux is a next-generation USB-C interface for using Serato DJ Pro with turntables, CDJs or other media players. The interface boasts superior audio qualities, a well-designed operating concept and a club-ready design. It can transform any conventional mixer into a professional digital vinyl system.

MAXIMUM FLEXIBILITY
Three stereo inputs provide DJs with maximum flexibility. Turntables, CDJs and similar can be used in any combination. The settings are adjusted using discreet DIP switches, which virtually eliminates any chance of accidental switching in the club. The interface includes three stereo outputs, including an AUX out that can be routed to Serato DJ Pro´s internal sampler. Gold-plated, corrosion-resistant RCA jacks ensure high-quality audio transmission.

FULL CONTROL
The Flux provides the best possible routing overview thanks to clearly visible signal flow LEDs for all inputs and outputs and a Thru status indicator. Connection status (hub, PD, DC) LED indicators on the top of the interface provide additional control options. The Direct Thru buttons on the top of the interface enable you to quickly and easily activate and disable Thru mode, which allows connected turntables and CDJs to be used conventionally. Navigation through the Serato software is no longer necessary.

HUB INSIDE
The Flux includes a built-in 2-port USB-A hub for connecting MIDI controllers and other USB accessories. Aside from the expanded connection options, the hub reduces potential connection faults in a busy club environment by keeping the setup connected even without the laptop.

STUDIO QUALITY – ANYTIME, ANYWHERE
The Flux offers studio quality in the club and wherever it's needed with 24-bit/96 kHz, high-quality digital/analogue converters and ultra-low latency. For this reason, it’s a superior DVS interface which could also be used as an audio interface in the studio.

ALWAYS POWERED
The Flux is bus-powered by a computer, so there's minimal wiring required for audio and power cables. The DVS interface can also be powered by external power sources through the USB-C DC input, allowing turntables and CDJs to be used in Thru mode even without a computer connected. The Flux's second USB-C port provides Power Delivery support for other USB-C devices (max. 60 W), such as a MacBook.

ROBUST AND ROADWORTHY
The interface has a durable metal housing with a scratch-resistant, black surface, ensuring a long service life even with heavy use. The extended edge design keeps the connections well-protected.

PLUG & PLAY FOR SERATO DJ Pro
The Reloop Flux unlocks the full version of Serato DJ Pro and Serato DVS. This means DJs can get up and running with the market-leading digital vinyl system in no time. Additional licences are not necessary.

FEATURES:
• 3-channel (6x6 in/out) USB-C DVS interface for Serato DJ Pro
• Turn any mixer into a professional digital vinyl system
• Unlocks full version of Serato DJ Pro and Serato DVS
• Studio-grade 24-bit sound card with crystal-clear audio and ultra-low latency response
• Supports up to 96kHz with high-quality D/A converters for superior audio processing
• Also functions as a stand-alone studio interface for recording and playback audio
• 3x inputs for turntables, CD players or AUX-In for live feed signal, switchable in any combination via dedicated dip switches
• Dedicated GND terminal for grounding turntables
• Gold-plated, corrosion-resistant audio connections
• 3x line outputs, including AUX-Out, assignable to the Sampler
• Easy, accessible direct thru buttons for analogue deck playback
• All terminals are visible from the top of the unit for easy installation in dark surroundings
• Bus-powered cable connection for power and audio
• Optional USB-C DC in port for external power supply
• Power delivery support for USB-C devices (max 60W)
• Signal-flow LEDs for all inputs and outputs (L/R) and thru indication for clear visibility
• Power LEDs on the top panel for connection status (Hub, PD, DC)
• 2-port USB-A hub for connecting further accessories
• Rugged, heavy-duty metal housing with a scratch-resistant black finish for durability on the road and reliability in the club
• Highly robust, extended edge design to protect connection terminals
• Supports the use of Serato NoiseMap™ control vinyl (not included) or custom control signal WAV file for use via CDs or USB drive (download available) with no additional license purchase needed
• Including: 2x RCA audio cables, 1x USB-A to USB-C, 1x USB-C to USB-C, user manual

TECHNICAL DATA:
Power:
• USB bus powered: Yes
• Recommended power: 2 A or higher / minimum power: 400 mA
• Maximum USB-PD throughput: 60 W
• Maximum USB Hub power output: 2 x 0.8 A = 8 W
• Supported external USB (type A or C) power supply: 5 V/1 A - 20 V/3 A
• Power supply priority: FLUX self-power -> USB Hub -> PD (to PC)

Audio:
• S/N Ratio (output reference level 1 kHz, +4 dB):
• Deck In (LINE signal input: 0 dBV): More than 83 dB
• Deck In (PHONO signal input: -32 dBV): More than 73 dB
• THD + N:
• LINE signal input: -4 dBV @1K / Less than 0.03% (1 kHz,+0 dB)
• PHONO signal input: -36 dBV @1K / Less than 0.05% (1 kHz,+0 dB, Inverse RIAA)

Maximum Gain:
• Deck In (LINE): +4 dB ± 2 dB
• Deck In (PHONO): +36 dB ± 2 dB
• Maximum Input (1 kHz, THD=1%):
• Deck In (LINE): More than +7 dBV
• Deck In (PHONO): More than -25 dBV
• Maximum Output (1 kHz, THD=1%):
• Deck Output: More than +11 dBV

USB:
• USB audio interface with 24 bit/44.1 kHz, 48 kHz, 96 kHz
• USB 2.0 high-speed (480 Mbit/s)
• Class-compliant on macOS
• USB Power Delivery Protocol 3.0

General:
• Dimensions (WxDxH): 160 x 120 x 34 mm
• Weight: 0.85 kg

Accessories:
• User Manual
• 1x USB type C/C cable
• 1x USB type C/A cable
• 2x RCA cables

Manual: https://www.reloop.com/media/catalog/product/pdf/2/4/5/245389_Reloop_IM.pdf

Designed for life on the road, the Reloop Flux Bag is a practical travel pouch for DVS interfaces, providing reliable protection and convenient transportation.

Specially made for the Reloop Flux DVS interface for Serato DJ Pro, this bag is made of high-quality neoprene material. It offers protection against liquids, dirt and dust, while the padded interior prevents damages and scratches.

The integrated mesh pocket keeps your cables, USB sticks and accessories organized. The compact design fits easily into your backpack and the durable zipper and carrying handle make it a perfect accessory for your Flux soundcard.

FEATURES:
• Protective carrying bag for DVS interfaces on the road
• Skillfully designed to fit the Reloop Flux DVS interface for Serato DJ Pro, providing a perfect fit
• High-quality Neoprene material ensures protection against liquids, dirt, and dust
• Integrated mesh pocket for cables, USB sticks, and accessories
• Padded interior lining for protection against shocks and scratches
• Handy format for an easy fit in your bag
• Sturdy zipper and convenient carrying handle

Reloop - Flux + UDG Creator Hardcase (HHV Bundle)
The Bundle contains 1x Reloop - Flux and 1x UDG Creator Hardcase.

RELOOP FLUX - 6X6 IN/OUT USB-C DVS INTERFACE FOR SERATO DJ PRO

We are excited to introduce the Reloop Flux: A next-generation 6x6 In/out USB-C DVS Interface for Serato DJ Pro. It can transform any conventional mixer into a professional digital vinyl system.

BACK TO THE MUSIC
The Reloop Flux is a next-generation USB-C interface for using Serato DJ Pro with turntables, CDJs or other media players. The interface boasts superior audio qualities, a well-designed operating concept and a club-ready design. It can transform any conventional mixer into a professional digital vinyl system.

MAXIMUM FLEXIBILITY
Three stereo inputs provide DJs with maximum flexibility. Turntables, CDJs and similar can be used in any combination. The settings are adjusted using discreet DIP switches, which virtually eliminates any chance of accidental switching in the club. The interface includes three stereo outputs, including an AUX out that can be routed to Serato DJ Pro´s internal sampler. Gold-plated, corrosion-resistant RCA jacks ensure high-quality audio transmission.

FULL CONTROL
The Flux provides the best possible routing overview thanks to clearly visible signal flow LEDs for all inputs and outputs and a Thru status indicator. Connection status (hub, PD, DC) LED indicators on the top of the interface provide additional control options. The Direct Thru buttons on the top of the interface enable you to quickly and easily activate and disable Thru mode, which allows connected turntables and CDJs to be used conventionally. Navigation through the Serato software is no longer necessary.

HUB INSIDE
The Flux includes a built-in 2-port USB-A hub for connecting MIDI controllers and other USB accessories. Aside from the expanded connection options, the hub reduces potential connection faults in a busy club environment by keeping the setup connected even without the laptop.

STUDIO QUALITY – ANYTIME, ANYWHERE
The Flux offers studio quality in the club and wherever it's needed with 24-bit/96 kHz, high-quality digital/analogue converters and ultra-low latency. For this reason, it’s a superior DVS interface which could also be used as an audio interface in the studio.

ALWAYS POWERED
The Flux is bus-powered by a computer, so there's minimal wiring required for audio and power cables. The DVS interface can also be powered by external power sources through the USB-C DC input, allowing turntables and CDJs to be used in Thru mode even without a computer connected. The Flux's second USB-C port provides Power Delivery support for other USB-C devices (max. 60 W), such as a MacBook.

ROBUST AND ROADWORTHY
The interface has a durable metal housing with a scratch-resistant, black surface, ensuring a long service life even with heavy use. The extended edge design keeps the connections well-protected.

PLUG & PLAY FOR SERATO DJ Pro
The Reloop Flux unlocks the full version of Serato DJ Pro and Serato DVS. This means DJs can get up and running with the market-leading digital vinyl system in no time. Additional licences are not necessary.

FEATURES:
• 3-channel (6x6 in/out) USB-C DVS interface for Serato DJ Pro
• Turn any mixer into a professional digital vinyl system
• Unlocks full version of Serato DJ Pro and Serato DVS
• Studio-grade 24-bit sound card with crystal-clear audio and ultra-low latency response
• Supports up to 96kHz with high-quality D/A converters for superior audio processing
• Also functions as a stand-alone studio interface for recording and playback audio
• 3x inputs for turntables, CD players or AUX-In for live feed signal, switchable in any combination via dedicated dip switches
• Dedicated GND terminal for grounding turntables
• Gold-plated, corrosion-resistant audio connections
• 3x line outputs, including AUX-Out, assignable to the Sampler
• Easy, accessible direct thru buttons for analogue deck playback
• All terminals are visible from the top of the unit for easy installation in dark surroundings
• Bus-powered cable connection for power and audio
• Optional USB-C DC in port for external power supply
• Power delivery support for USB-C devices (max 60W)
• Signal-flow LEDs for all inputs and outputs (L/R) and thru indication for clear visibility
• Power LEDs on the top panel for connection status (Hub, PD, DC)
• 2-port USB-A hub for connecting further accessories
• Rugged, heavy-duty metal housing with a scratch-resistant black finish for durability on the road and reliability in the club
• Highly robust, extended edge design to protect connection terminals
• Supports the use of Serato NoiseMap™ control vinyl (not included) or custom control signal WAV file for use via CDs or USB drive (download available) with no additional license purchase needed
• Including: 2x RCA audio cables, 1x USB-A to USB-C, 1x USB-C to USB-C, user manual

TECHNICAL DATA:
Power:
• USB bus powered: Yes
• Recommended power: 2 A or higher / minimum power: 400 mA
• Maximum USB-PD throughput: 60 W
• Maximum USB Hub power output: 2 x 0.8 A = 8 W
• Supported external USB (type A or C) power supply: 5 V/1 A - 20 V/3 A
• Power supply priority: FLUX self-power -> USB Hub -> PD (to PC)

Audio:
• S/N Ratio (output reference level 1 kHz, +4 dB):
• Deck In (LINE signal input: 0 dBV): More than 83 dB
• Deck In (PHONO signal input: -32 dBV): More than 73 dB
• THD + N:
• LINE signal input: -4 dBV @1K / Less than 0.03% (1 kHz,+0 dB)
• PHONO signal input: -36 dBV @1K / Less than 0.05% (1 kHz,+0 dB, Inverse RIAA)

Maximum Gain:
• Deck In (LINE): +4 dB ± 2 dB
• Deck In (PHONO): +36 dB ± 2 dB
• Maximum Input (1 kHz, THD=1%):
• Deck In (LINE): More than +7 dBV
• Deck In (PHONO): More than -25 dBV
• Maximum Output (1 kHz, THD=1%):
• Deck Output: More than +11 dBV

USB:
• USB audio interface with 24 bit/44.1 kHz, 48 kHz, 96 kHz
• USB 2.0 high-speed (480 Mbit/s)
• Class-compliant on macOS
• USB Power Delivery Protocol 3.0

General:
• Dimensions (WxDxH): 160 x 120 x 34 mm
• Weight: 0.85 kg

Accessories:
• User Manual
• 1x USB type C/C cable
• 1x USB type C/A cable
• 2x RCA cables

Manual: https://www.reloop.com/media/catalog/product/pdf/2/4/5/245389_Reloop_IM.pdf

UDG - Creator Reloop Flux Hardcase

A Digital DJ/ Producer looking for a professional, durable case solution for your Reloop Flux? Then look no further, UDG developed a super light EVA Hardcase designed for life on the road. Constructed from durable lightweight compression moulded EVA material with a laminated nylon exterior this case provides protection against drops, scratches & liquids. Skillfully designed & moulded to fit the Reloop Flux, this case is perfect for the travelling DJ/ Producer that needs to protect their equipment.

Weight 0,20 kg / 0.44 lbs
Outer Dimensions (W x H x D) 21.0 x 18.5 x 6.2 cm | 8.3 x 7.3 x 2.4 inch
Inner Dimensions (W x H x D) 16.0 x 13.0 x 5.2 cm | 6.3 x 5.1 x 2.0 inch
Material Durashock molded EVA foam
Protection Cover main material 600D polyester with 5 mm EVA durashock molded body
Water repellent laminated nylon exterior
Black soft fleece interior
Protective top removable foam
Extra's Easy grip zipper pulls
Fits Reloop Flux

The perfect companion for DJs and music lovers on the go. Designed for practicality and protection, the Reloop Premium Headphone Bag XT combines a sleek, durable exterior with clever features. It can hold most common DJ headphones for a secure fit while traveling.

Made of lightweight Durashock molded EVA foam with a durable polyester outer shell, the bag protects your headphones from common travel threats such as bumps, spills, dirt and dust.

The bag is equipped with a convenient carrying handle for easy transport and a snap hook for easy attachment to your luggage. Additionally, it comes with an adjustable and detachable shoulder strap, ensuring flexibility in how it can be carried. A mesh pocket inside helps you keep your cables and accessories organized. The durable zippers are built to withstand everyday use.

FEATURES:
• Professional DJ headphone travel bag in a sleek, high-quality design
• Universal fit for most common DJ headphones
• Made of lightweight Durashock molded EVA foam and a polyester exterior shell for a reliable protection
• Keep your headphones safe from bumps, liquids, dirt and dust
• Including a convenient carrying handle and a snap hook for easy luggage attachment
• Adjustable and a detachable shoulder strap
• Mesh-compartment for cables and accessories
• Durable zippers for everyday use

STANDARD REDEFINED
The professional RMX-95 4+1 channel club mixer blurs the lines between analogue workflow and digital technology. The RMX-95 is a cutting-edge, extraordinarily versatile creative tool thanks to its dual-USB 2.0 interface, redesigned effects section, optional MIDI mapping of all controls, and smooth integration of the djay PRO AI DJ software. The club mixer has a familiar and user-friendly interface, making it suitable for both professional and hobby DJs.

SURGICAL SOUND MANIPULATION IN EVERY DETAIL
Will you go for "Classic" or "Kill"? The RMX-95's 3-band EQ can be adjusted to allow maximum sound control for unique results.
Echo, Reverb, Flanger, Phaser, Vinyl Brake, Loop Roll, Noise, Pitch Shift, Delay, Ping Pong Delay, Tape Delay, Bit Crusher and Transformer are just some of the many studio-quality effects included in the brand-new Beat FX unit. The dedicated FX frequency control (LPF/HPF) lets you apply the effects to a specific frequency range for a more unique sound.
And that's not all: Each channel also features a bipolar filter unit (LPF and HPF) with real-time resonance adjustment. This allows for even more complex sound productions.
Two digital displays show parameter changes in real time for precise control that goes beyond hearing.

CONNECTIONS GALORE
The RMX-95 also excels in terms of connectivity: Four CD, two line, and two phono inputs are available on the four input channels. The separate microphone channel has two microphone connections (1 x jack, 1 x jack/XLR combination jack) and an additional AUX input. The master output offers RCA or balanced XLR cable connections. The booth output has two jack connections for stereo operation. However, it can also be used in mono mode. A recording device can be connected to the Rec output via RCA jacks to record DJ sets – regardless of the master output level. Last but not least, the DJ mixer has two jacks for headphones.

MAXIMUM FLEXIBILITY: DUAL-USB AUDIO INTERFACE
Superior 24-bit sound quality is provided by the ten inputs and outputs of the high-quality dual-USB 2.0 interface. The two USB ports allow smooth transitions between DJs and maximum flexibility when using different setups in a single club night. In addition, the active USB hub enables the connection of additional USB devices.

FULLY DIGITAL ARCHITECTURE
The RMX-95's digital architecture transforms the DJ mixer into an individually mappable MIDI controller. As part of this, the setup menu provides a wealth of customisable options, such as EQ frequency range, Neural Mix™ EQ mode, audio interface routing, and zone routing for the booth output.

DVS-ENABLED FOR DJAY PRO AI & NEURAL MIX™
The RMX-95 works with Algoriddim djay PRO AI via plug and play. The DJ app's ground-breaking Neural Mix function lets you isolate beats, melodies, and vocals in the mix in real time. The RMX-95 supports djay PRO AI's advanced DVS integration with Mac, PC, iPhone and iPad. The DJ software is also compatible with streaming services like Tidal¹, Soundcloud¹, Beatport Link¹ or Beatsource Link¹.

CRISP CUTS AND SMOOTH BLENDING
The adjustable curve of all faders provides DJs with the creative flexibility they want while mixing. Turntablists and scratch wizzards can also upgrade the crossfader with the contactless RMX innoFADER.

INDESTRUCTIBLE DESIGN
The club mixer's sleek black metal surface is not only eye-catching but also highly durable. The solid metal housing and hard-wearing metal shafts in all of the built-in potentiometers and switches provide a long service life, even with heavy club use.

FEATURES:
• Professional 4+1-channel DJ club mixer
• DUAL 10 In/Out USB 2.0 audio interface with superb, 24-bit sound quality
• New Beat FX unit with multiple effects in studio quality: Echo, Reverb, Flanger, Phaser, Vinyl Brake, Loop Roll, Noise, Pitch Shift, Delay, Ping Pong Delay, Tape Delay, Bit Crusher,Transformer
• FX frequency control (LPF/HPF) for manipulating effects in selected frequency band
• Sound filters: Bi-polar filter unit with LPF and HPF
• Realtime resonance control for channel filters
• Active USB hub to connect USB accessories
• 3-band EQ with adjustable behaviour (classic/kill)
• Two digital displays showing real-time information of parameter changes
• Digital mixer architecture with extensive adjustment options
• Extensive setup menu, including:
• EQ frequency range (low, high)
• Neural Mix™ EQ mode
• Audio interface routing
• Booth output zone routing (matrix)
• CUE solo option
• RMX innoFADER compatible
• Adjustable linefader and crossfader curves
• MIDI-compatible control elements
• 2x High-retention USB 2.0 port, especially durable
• 2x Mic inputs with dedicated MIC ON button
• 2x Headphone outputs via 6.3/3.5 mm stereo jack with split cue
• 2x Mic inputs with dedicated MIC ON button
• Booth output in stereo or mono
• High-quality and hard-wearing, pure black metallic finish
• Sturdy construction in a metal housing with bolted metal shafts
• Kensington lock to secure the device
• Incl. manual, power cord, and USB cable

PREMIUM BELT DRIVE USB TURNTABLE SYSTEM

HIGHLIGHTS:
Belt-driven HiFi turntable with Ortofon 2M Red
20 mm acrylic platter with LED lighting
Decentralised drive motor with external belt guide

SOUND MEETS DESIGN
The Turn 7 bridges the gap between high-end HiFi turntables and uncompromising design. The belt-driven turntable meets the exacting demands of audiophile music fans thanks to precisely manufactured components. The acrylic platter with LED lighting and the external drive belt make the Turn 7 an absolute eye-catcher.

POWERFUL AND STEADY DRIVE
A decentralised, low-vibration DC motor drives the Turn 7. The integral flat belt runs gracefully along the turntable exterior, ensuring smooth operation and a sophisticated appearance. The start/stop rotary switch allows you to select between the turntable's two speeds (33 and 45 RPM).

HEART OF ACRYLIC: THE TURNTABLE PLATTER
The acrylic platter is 20 mm thick, weighs 1.7 kg, and has outstanding evenness thanks to precision manufacturing. It also has excellent antistatic characteristics. As a result, crystal-clear audio is possible without using a platter mat. The satin finish of the material creates a focal point and contrasts with the otherwise plain design of the belt-driven turntable.

LET THERE BE LIGHT – LEDS INSIDE
One of the unique features of the Turn 7 is the optional, blue platter illumination. Inconspicuously placed beneath the platter, multiple LEDs with a diffuser cover sets the mood and creates a warm and inviting ambience.

TOP-CLASS TONE ARM
The high-quality carbon tone arm has exceptional acoustic properties. The turntable's authentic sound is brought out to its full potential by effectively cancelling out vibrations. The ability to adjust the height (vertical tracking angle – VTA) and an anti-skating adjustment ensure maximum precision.

ORTOFON 2M RED PRE-INSTALLED
The turntable comes with the Ortofon 2M Red cartridge system pre-installed. The Ortofon 2M Red has an elliptical stylus tip and excellent sonic characteristics, including first-rate sound accuracy and reproduction. The Ortofon 2M Red is a highly versatile cartridge system with an open, dynamic sound and warm tones. The universal headshell connection (SME) adds more options for cartridge systems.

METICULOUSLY PERFECTED
In addition to its high-quality preamplifier, the Turn 7 also features versatile switching between line and phono signals. The gold-plated corrosion-resistant RCA connectors ensure the best possible signal transmission. The built-in USB output allows you to digitise vinyl records.

SIMPLE DESIGN & PURE FUNCTIONALITY
The sturdy MDF wooden plinth and height-adjustable isolator feet with aluminium surround provide effective decoupling for the turntable. The high-gloss piano lacquer is a classy contrast to the timeless minimalism while emphasising the Turn 7's superior quality.

FEATURES:
• Premium belt-driven HiFi turntable
• Decentralised DC motor with external drive belt on the acrylic platter
• Fully manual operation with motor control switch for switching between speeds (33/45 RPM)
• Precision-machined, 20 mm thick solid acrylic platter (1.7 kg) with outstanding levelling and electrostatic properties for a crystal-clear sound
• Indirect blue LED lighting on the acrylic platter (can be switched on/off)
• Audiophile carbon tonearm with height adjustment (VTA) and anti-skating adjustment
• Pre-installed Ortofon 2M Red cartridge for optimised sound reproduction and fidelity
• Universal headshell connection (SME) for additional flexibility
• USB recording function: Recording and digitisation of vinyl via the simply USB connection for PC/Mac
• High-quality integrated preamp (switchable phono/line output)
• Gold-plated, corrosion-resistant audio connections (removable power and RCA cable)
• Height-adjustable, shockproof aluminium feet for effective decoupling
• Solid MDF plinth with piano finish and a timeless design
• Incl.: dust cover, 2x hinges, felt mat, international power supply (UK/EU/US), RCA cable, headshell with Ortofon 2M Red (pre-installed), 7" aluminium adapter, acrylic turntable platter, allen key, USB-cable, instruction manual & counterweight

TECHNICAL SPECIFICATIONS:
Turntable Section:
• Type of turntable: Belt-Driven manual Turntable System with USB Interface
• Drive: Belt drive
• Motor: DC Motor
• Rotation speeds: 33 1/3, 45
• Starting Torque: //
• Start-up time / rpm change: //
• Wow and Flutter: 0,2% WRMS
• S/N Ratio: >45dB or higher
• Breaking System: Manually
Turntable Platter:
• Turntable Platter: Acrylic glass
• Diameter: 300 mm
• Weight: 1.7 kg
Tonearm Section:
• Type: Straight Tonearm
• Effective Length: 223.6 mm
• Overhang: 18.61 mm
• Tracking Error Angle: ±1.5°
• VTA Adjustment Range: - 2 ~ 4 mm
• Applicable Cartridge Weight: 7.2 ~ 11.2 g (incl. Headshell)
• Anti-Skating Range: 0 - 4 mm
• Terminals: 1x PHONO/LINE Out
Cartridge:
• Ortofon 2M Red
• Output voltage at 1000 Hz, 5cm/sec.: 5.5 mV
• Channel balance at 1 kHz: 1.5 dB
• Channel separation at 1 kHz: 22 dB
• Channel separation at 15 kHz: 15 dB
• Frequency response: 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force: 70 µ Mm
• Compliance, dynamic, lateral: 20 µ Mm
• Stylus type: Elliptical
• Stylus tip radius: r/R 8/18 µm
• Tracking force range: 1.6-2.0 g (16-20 mN)
• Tracking force, recommended: 1.8 g (18 mN)
• Tracking angle: 24.7°
• Internal impedance, DC resistance: 1.3 kOhm
• Internal inductance: 700 mH
• Recommended load resistance: 47 kOhm
• Recommended load capacitance: 150-300 pF
• Cartridge colour, body/stylus: Black/Red
• Cartridge weight: 7.2 g
General:
• Power Supply: 12V, 1A DC
• Power consumption: 12W
• Dimensions: 420(W) x 356(D) x 148(H) mm
• Weight: 8.2 kg

STANTON STX
LIMITED EDITION PORTABLE SCRATCH TURNTABLE
RAZOR SHARP CUTS, RIGHT AWAY

The STX is the only portable turntable that comes with a factory-installed mini Innofader Nano crossfader. Designed to last over 4 million cycles, this buttery-smooth fader and can be easily swapped between left and right positions to accommodate both left-handed and right-handed scratch styles. The independent crossfader Cut-In and Curve knobs deliver an unrivaled level of crossfader customization, allowing DJs to precisely calibrate the crossfader to suit their own style. This level of customization, along with the ultra-stable platter and tonearm, makes it easy to achieve the absolute cleanest cuts possible.

SCRATCH WHENEVER, WHEREVER
Second only to a sharp, ultra-precise crossfader, ease of portability is vital for a portablism-focused turntable. High-quality rechargeable Lithium-ion batteries are included with the STX, providing enough portable power for hours of mobile use.
The batteries can easily be charged by connecting the unit to a computer or wall charger using the USB-C input. For extended scratch sessions, the USB-C input can also be used with external power sources for even more cutting time.
To top everything off (literally), the latching lid also functions as a stackable, latching base, to bring the STX to standard turntable height.

WELL-CONNECTED FOR CREATORS
Performing with beats and loopers is as simple as connecting a smartphone wirelessly with Bluetooth or with the 1/8” stereo input. The USB port with one-touch recording makes it fast and easy to record high-quality session audio for social media content creation, while the stereo RCA outputs allow you to connect external mixers and speakers for live performances.

PERFORMANCE READY
The modification culture is alive and well in the portablism world. Since the inception of this art form, we’ve seen ingenious designs and customizations. The most popular and utilitarian mods are already included on the STX, including a Start/Stop button, an on-board speaker, and a pitch slider with Ultra-Pitch selection switch. These key features allow for inspiring performances right out of the box and provide a solid foundation upon which DJs can further customize to match their own unique portablist style.

Technical Specifications
Connections (1) RCA line-level output (stereo pair)
(1) 1/4” (6.35 mm) stereo headphone output
(1) 1/8” (3.5 mm) stereo headphone output
(1) 1/8” (3.5 mm) stereo input
(1) USB-C port (charges the internal battery)
(1) USB-A port (USB flash drive recordings

Speeds 33 1/3, 45, 78 RPM (45 RPM adapter included)

Power (2) 3.7V Li-ion batteries

Dimensions
(width x depth x height)
13.0” x 13.0” x 4.0” (3.25” without cover attached)
330.2 x 330.2 x 101.6 mm (82.6 mm without cover attached)

Weight 5.3 lbs.
2.4 kg

Made in Japan, STOKYO turntable replacement headshell

Official STOKYO headshell same type as you will find on Technics SL-1200
High Quality finish (Matte)
Lead wires (Shielded)