DJ Equipment 420 Items

RELOOP FLUX - 6X6 IN/OUT USB-C DVS INTERFACE FOR SERATO DJ PRO

We are excited to introduce the Reloop Flux: A next-generation 6x6 In/out USB-C DVS Interface for Serato DJ Pro. It can transform any conventional mixer into a professional digital vinyl system.

BACK TO THE MUSIC
The Reloop Flux is a next-generation USB-C interface for using Serato DJ Pro with turntables, CDJs or other media players. The interface boasts superior audio qualities, a well-designed operating concept and a club-ready design. It can transform any conventional mixer into a professional digital vinyl system.

MAXIMUM FLEXIBILITY
Three stereo inputs provide DJs with maximum flexibility. Turntables, CDJs and similar can be used in any combination. The settings are adjusted using discreet DIP switches, which virtually eliminates any chance of accidental switching in the club. The interface includes three stereo outputs, including an AUX out that can be routed to Serato DJ Pro´s internal sampler. Gold-plated, corrosion-resistant RCA jacks ensure high-quality audio transmission.

FULL CONTROL
The Flux provides the best possible routing overview thanks to clearly visible signal flow LEDs for all inputs and outputs and a Thru status indicator. Connection status (hub, PD, DC) LED indicators on the top of the interface provide additional control options. The Direct Thru buttons on the top of the interface enable you to quickly and easily activate and disable Thru mode, which allows connected turntables and CDJs to be used conventionally. Navigation through the Serato software is no longer necessary.

HUB INSIDE
The Flux includes a built-in 2-port USB-A hub for connecting MIDI controllers and other USB accessories. Aside from the expanded connection options, the hub reduces potential connection faults in a busy club environment by keeping the setup connected even without the laptop.

STUDIO QUALITY – ANYTIME, ANYWHERE
The Flux offers studio quality in the club and wherever it's needed with 24-bit/96 kHz, high-quality digital/analogue converters and ultra-low latency. For this reason, it’s a superior DVS interface which could also be used as an audio interface in the studio.

ALWAYS POWERED
The Flux is bus-powered by a computer, so there's minimal wiring required for audio and power cables. The DVS interface can also be powered by external power sources through the USB-C DC input, allowing turntables and CDJs to be used in Thru mode even without a computer connected. The Flux's second USB-C port provides Power Delivery support for other USB-C devices (max. 60 W), such as a MacBook.

ROBUST AND ROADWORTHY
The interface has a durable metal housing with a scratch-resistant, black surface, ensuring a long service life even with heavy use. The extended edge design keeps the connections well-protected.

PLUG & PLAY FOR SERATO DJ Pro
The Reloop Flux unlocks the full version of Serato DJ Pro and Serato DVS. This means DJs can get up and running with the market-leading digital vinyl system in no time. Additional licences are not necessary.

FEATURES:
• 3-channel (6x6 in/out) USB-C DVS interface for Serato DJ Pro
• Turn any mixer into a professional digital vinyl system
• Unlocks full version of Serato DJ Pro and Serato DVS
• Studio-grade 24-bit sound card with crystal-clear audio and ultra-low latency response
• Supports up to 96kHz with high-quality D/A converters for superior audio processing
• Also functions as a stand-alone studio interface for recording and playback audio
• 3x inputs for turntables, CD players or AUX-In for live feed signal, switchable in any combination via dedicated dip switches
• Dedicated GND terminal for grounding turntables
• Gold-plated, corrosion-resistant audio connections
• 3x line outputs, including AUX-Out, assignable to the Sampler
• Easy, accessible direct thru buttons for analogue deck playback
• All terminals are visible from the top of the unit for easy installation in dark surroundings
• Bus-powered cable connection for power and audio
• Optional USB-C DC in port for external power supply
• Power delivery support for USB-C devices (max 60W)
• Signal-flow LEDs for all inputs and outputs (L/R) and thru indication for clear visibility
• Power LEDs on the top panel for connection status (Hub, PD, DC)
• 2-port USB-A hub for connecting further accessories
• Rugged, heavy-duty metal housing with a scratch-resistant black finish for durability on the road and reliability in the club
• Highly robust, extended edge design to protect connection terminals
• Supports the use of Serato NoiseMap™ control vinyl (not included) or custom control signal WAV file for use via CDs or USB drive (download available) with no additional license purchase needed
• Including: 2x RCA audio cables, 1x USB-A to USB-C, 1x USB-C to USB-C, user manual

TECHNICAL DATA:
Power:
• USB bus powered: Yes
• Recommended power: 2 A or higher / minimum power: 400 mA
• Maximum USB-PD throughput: 60 W
• Maximum USB Hub power output: 2 x 0.8 A = 8 W
• Supported external USB (type A or C) power supply: 5 V/1 A - 20 V/3 A
• Power supply priority: FLUX self-power -> USB Hub -> PD (to PC)

Audio:
• S/N Ratio (output reference level 1 kHz, +4 dB):
• Deck In (LINE signal input: 0 dBV): More than 83 dB
• Deck In (PHONO signal input: -32 dBV): More than 73 dB
• THD + N:
• LINE signal input: -4 dBV @1K / Less than 0.03% (1 kHz,+0 dB)
• PHONO signal input: -36 dBV @1K / Less than 0.05% (1 kHz,+0 dB, Inverse RIAA)

Maximum Gain:
• Deck In (LINE): +4 dB ± 2 dB
• Deck In (PHONO): +36 dB ± 2 dB
• Maximum Input (1 kHz, THD=1%):
• Deck In (LINE): More than +7 dBV
• Deck In (PHONO): More than -25 dBV
• Maximum Output (1 kHz, THD=1%):
• Deck Output: More than +11 dBV

USB:
• USB audio interface with 24 bit/44.1 kHz, 48 kHz, 96 kHz
• USB 2.0 high-speed (480 Mbit/s)
• Class-compliant on macOS
• USB Power Delivery Protocol 3.0

General:
• Dimensions (WxDxH): 160 x 120 x 34 mm
• Weight: 0.85 kg

Accessories:
• User Manual
• 1x USB type C/C cable
• 1x USB type C/A cable
• 2x RCA cables

Manual: https://www.reloop.com/media/catalog/product/pdf/2/4/5/245389_Reloop_IM.pdf

To clean your vinyl records thoroughly, it is important to place them on a soft, dirt-free surface. With the cleaning mat for vinyl records, HHV has created a solution that makes caring for your vinyl even easier.
Place the record in the middle of the cleaning mat and use Vinyl Care products such as the practical cleaning roller to remove dust and dirt from your vinyl. CDs or DVDs can easily be placed in the corner of the mat. The use of a plastic adapter is recommended for cleaning 7-inch records.
All Vinyl Care by HHV products are developed with direct feedback from our customers and offer innovative solutions for the care and storage of vinyl records.

The cleaning roller offers you a time-saving and effective way to clean your records. Dust and dirt simply stick to the silicone surface of the roller. It is very easy to use: Carefully place the record on a clean, soft surface such as the Record Cleaning Work Mat from the HHV Vinyl Care series. Hold the cleaning roller by the handle and place the silicone roller on the record. Carefully roll over the entire surface of the record, changing direction several times.
To remove dust and dirt from the Record Cleaning Roller, wash it with lukewarm soapy water. Allow it to dry completely before using it again and store it in the storage box provided. Sunlight and chemical cleaning agents damage the roller and should therefore be avoided at all costs.
As part of the Vinyl Care series from HHV, we have developed the record cleaning roller especially for the needs of vinyl collectors. We incorporate the experience of our customers directly into product development.

The RECORD BOX record tower is an innovative set of two record boxes and a register box, which are connected by means of practical adhesive points. In total, the record tower offers space for the storage and presentation of a maximum of 310 12'' records.

Ideal for DJs, record stores and the home record collection: The register box is the top component of the tower and gives you direct access to your most important records, which you can easily browse through. The stacked record boxes prove to be a space-saving storage option that keeps things tidy and organized.

Easy assembly and creative freedom: The set of three record boxes is part of RECORD BOX's unique furniture system, which allows you to make creative additions that perfectly suit your needs. The assembly is very easy, the connection is made with the non-slip glue dots, which were developed especially for this system.

Clever solutions for your individual needs: The Record Tower is available in white, grey and black. Buying the set offers you a saving compared to buying the boxes individually and gives you all the design freedom you need for your record furniture. The boxes are made of 15 mm MDF with melamine and offer you a lot of stability as well as a clear look at an excellent price-performance ratio.

Features:

• Record tower as a combination of two 12-inch 110 storage boxes and one 12-inch 100 storage register box
• Connection through non-slip silicone adhesive dots
• Favorable bundle price compared to single purchase
• Available in white, grey and black
• Space for more than 300 LPs
• Ideal for DJs, record stores, the home record collection
• Can be combined in many ways with the other products in the RECORD-BOX furniture series
• Boxes for self-assembly - screwdriver required!

Technical data:

• Material: MDF wood (15 mm) with melamine coating.
• Dimensions: approx. 36 x 36 x approx. 104 cm
• 1x 12-inch 100 storage boxes
• 2x 12-Inch 110 Storage Boxes
• 1x adhesive dots from RECORD BOX
• assembly instructions
• Weight: 12,7 kg

The RECORD BOX record tower is an innovative set of two record boxes and a register box, which are connected by means of practical adhesive points. In total, the record tower offers space for the storage and presentation of a maximum of 310 12'' records.

Ideal for DJs, record stores and the home record collection: The register box is the top component of the tower and gives you direct access to your most important records, which you can easily browse through. The stacked record boxes prove to be a space-saving storage option that keeps things tidy and organized.

Easy assembly and creative freedom: The set of three record boxes is part of RECORD BOX's unique furniture system, which allows you to make creative additions that perfectly suit your needs. The assembly is very easy, the connection is made with the non-slip glue dots, which were developed especially for this system.

Clever solutions for your individual needs: The Record Tower is available in white, grey and black. Buying the set offers you a saving compared to buying the boxes individually and gives you all the design freedom you need for your record furniture. The boxes are made of 15 mm MDF with melamine and offer you a lot of stability as well as a clear look at an excellent price-performance ratio.

Features:

• Record tower as a combination of two 12-inch 110 storage boxes and one 12-inch 100 storage register box
• Connection through non-slip silicone adhesive dots
• Favorable bundle price compared to single purchase
• Available in white, grey and black
• Space for more than 300 LPs
• Ideal for DJs, record stores, the home record collection
• Can be combined in many ways with the other products in the RECORD-BOX furniture series
• Boxes for self-assembly - screwdriver required!

Technical data:

• Material: MDF wood (15 mm) with melamine coating.
• Dimensions: approx. 36 x 36 x approx. 104 cm
• 1x 12-inch 100 storage boxes
• 2x 12-Inch 110 Storage Boxes
• 1x adhesive dots from RECORD BOX
• assembly instructions
• Weight: 12,7 kg

Symbolic picture!

The Record Box Record Player Lowboard is much more than a hi-fi sideboard, it's a nice retro design made for vinyl lovers who put emphasis on interior furnishing without lacking functionality. After a fast and easy assembly, the Record Box Lowboard offers storage for up to 70 records while a separate compartment holds the one being currently played or those about to be played.

Record Box Record Player Lowboard - Features:

• usable on both sides (turntable can be placed on the left and the records on the right or vice versa)
• space for turntable and amplifier
• holds up to 70 records
• separate space for records in use
• support material: solid wood (natural or dark purple finish)
• cabinet material: white laminated composite board
• external dimensions: 90 x 38 x 42 cm (L x H x W)
• turntable area: 48 x 42 cm
• amp compartment: 45 x 19 x 42 cm (L x H x B)
• pre-selection rackl: 5 cm
• shelf for storage of 12" vinyl records: 38.5 x 40.5 cm
• product weight: 12.9 kg
• packaging dimensions: 102 x 52.5 x 8.5 cm
• total shipping weight: 14 kg
• Boxes for self-assembly - screwdriver required!

The Record Box Record Player Lowboard is much more than a hi-fi sideboard, it's a nice retro design made for vinyl lovers who put emphasis on interior furnishing without lacking functionality. After a fast and easy assembly, the Record Box Lowboard offers storage for up to 70 records while a separate compartment holds the one being currently played or those about to be played.

Record Box Record Player Lowboard - Features:

• usable on both sides (turntable can be placed on the left and the records on the right or vice versa)
• space for turntable and amplifier
• holds up to 70 records
• separate space for records in use
• support material: solid wood (natural or dark purple finish)
• cabinet material: white laminated composite board
• external dimensions: 90 x 38 x 42 cm (L x H x W)
• turntable area: 48 x 42 cm
• amp compartment: 45 x 19 x 42 cm (L x H x B)
• pre-selection rackl: 5 cm
• shelf for storage of 12" vinyl records: 38.5 x 40.5 cm
• product weight: 12.9 kg
• packaging dimensions: 102 x 52.5 x 8.5 cm
• total shipping weight: 14 kg
• Boxes for self-assembly - screwdriver required!

Symbolic picture!

The Record Box Record Player Lowboard is much more than a hi-fi sideboard, it's a nice retro design made for vinyl lovers who put emphasis on interior furnishing without lacking functionality. After a fast and easy assembly, the Record Box Lowboard offers storage for up to 70 records while a separate compartment holds the one being currently played or those about to be played.

Record Box Record Player Lowboard - Features:

• usable on both sides (turntable can be placed on the left and the records on the right or vice versa)
• space for turntable and amplifier
• holds up to 70 records
• separate space for records in use
• support material: solid wood (natural or dark purple finish)
• cabinet material: white laminated composite board
• external dimensions: 90 x 38 x 42 cm (L x H x W)
• turntable area: 48 x 42 cm
• amp compartment: 45 x 19 x 42 cm (L x H x B)
• pre-selection rackl: 5 cm
• shelf for storage of 12" vinyl records: 38.5 x 40.5 cm
• product weight: 12.9 kg
• packaging dimensions: 102 x 52.5 x 8.5 cm
• total shipping weight: 14 kg
• Boxes for self-assembly - screwdriver required!

The R.A. The Rugged Man Logo Slipmat is made from lightweight felt and equipped with a fresh graphic that bigs up the latest albums by R.A. The Rugged Man. Style meets function to the highest degree.

Eco-friendly record cleaning concentrate for VC-S, VC-E & VC-S2

The ultimate eco-friendly record cleaning concentrate

This new cleaning formula was developed exclusively by Pro-Ject Audio Systems. It does not contain alcohol, which may harm record surfaces. Wash it contains only high-purity components, which are 100% eco-friendly, non-toxic and non-flammable. Wash it is the first solution to clean vinyls & shellac records gentle, but efficiently. Wash it will evaporate without leaving residues on the record surface!

250 ml (will clean about 337 records)

Features
•New highly concentrated cleaning formula by Pro-Ject
•Wash it cleans vinyl records & shellacs
•Wash it contains only high-purity components
•Eco-friendly - Non-toxic - Non-flammable
•Record looks like new after washing
•Dissolves a wide range of impurities including fat/grease
•For very dirty records repeat the cleaning process
•Evaporates quickly and leaves zero residues
•Optimum mix ratio 1:10 to 1:20 with distilled/demineralized water - do not use tap water!
•Optimum application temperature 20 - 40 degrees (mixing ratio for warmed Wash it is 1:20)
•Optimum storage temperature 10 - 25 degrees

Features
•Gently cleans your vinyl while playing
•Follows the grooves
•Heavy weight base for secure placement
•Uni-pivot design
•Easy setup
•Suitable for Primary, Essential and Debut turntables
•Elegant looks
•Durable materials
•Brush made of natural hair

Technical Specifications
•Weight: 430 g
•Arm-length: 226 mm
•Arm material: Aluminium
•Brush: Hair

2-way bookshelf speakers

And these are comments from audio testers:
• Well tuned and upbeat basslines
• Lively dynamics
• Surprisingly low coloration
• Good transparency and reasonable image depth
• Bass is fast and tuneful, this is what really matters!

Scope of delivery:
• 2x Speaker Box 5
• 2x speaker grill black
• 1x pair of gloves

Features:
• Audiophile bass-reflex design
• Gold-plated speaker terminal (single-wired)
• Simple Wall-mount included
• Magnetically shielded
• Front cover with magnetic attachment
• Speaker-Box Wall Bracket available as an option

Technical Specifications:
• Sensitivity (1W/1m): 86 dB
• Recommended amplifier power: 10 to 150 watts
• Tweeter: 25 mm Ø silk-dome Neodymium magnet
• Woofer: 130 mm Ø fiberglass cone
• Frequency response: 55 Hz - 20 kHz
• Impedance: 4 - 8 Ohms
• Dimensions: W x H x D 160 x 255 x 210 mm
• Weight: 4.2 kg

2-way bookshelf speakers

And these are comments from audio testers:
• Well tuned and upbeat basslines
• Lively dynamics
• Surprisingly low coloration
• Good transparency and reasonable image depth
• Bass is fast and tuneful, this is what really matters!

Scope of delivery:
• 2x Speaker Box 5
• 2x speaker grill black
• 1x pair of gloves

Features:
• Audiophile bass-reflex design
• Gold-plated speaker terminal (single-wired)
• Simple Wall-mount included
• Magnetically shielded
• Front cover with magnetic attachment
• Speaker-Box Wall Bracket available as an option

Technical Specifications:
• Sensitivity (1W/1m): 86 dB
• Recommended amplifier power: 10 to 150 watts
• Tweeter: 25 mm Ø silk-dome Neodymium magnet
• Woofer: 130 mm Ø fiberglass cone
• Frequency response: 55 Hz - 20 kHz
• Impedance: 4 - 8 Ohms
• Dimensions: W x H x D 160 x 255 x 210 mm
• Weight: 4.2 kg

Features
•Built-in phono stage
•Switchable phono and line output
•Belt-drive with synchronous motor
•Ortofon quality cartridge
•Vibration absorbing feet
•NO plastic
•Machined special composit fibre chassis
•Light-weight, high-precision aluminium tonearm
•Sapphire tonearm bearing
•Gold-plated contacts
•Stainless steel bronze bushing
•Elegant dust cover with adjustable hinges
•Silicon belt with optimum damping
•Hand-made in Europe

Technical Specifications
•Outputs: RCA Phono/Line
•Speed: 33, 45 (manual speed change)
•Principle: Belt drive
•Speed variance: 33: 0.8% 45: 0.7%
•Wow & Flutter: 33: 0.29% 45: 0.27%
•Platter: 300 mm with felt mat
•Main bearing: Stainless steel
•Tonearm: 8.6” aluminium
•Effective arm length: 218.5 mm
•Overhang: 22.0 mm
•Effective tonearm mass: 8.0 g
•Counterweight for mass: 3 - 7 g (supplied)
•Tracking force range: 0 - 25mN (18mN pre-adjusted)
•Included accessories: Dust cover
•Power consumption: 4.5 Watts max
•Dimensions: 420 x 112 x 330mm (WxHxD)
•Weight: 4.0 kg net

After the Debut Carbon EVO revolutionized the Debut series in 2020, the Debut PRO raises the bar even higher.

A MILESTONE FOR THE NEXT DECADES
The Debut PRO brings an absolutely new design to Pro-Ject turntables. The audiophile turntable is convincing in all respects – not only visually, but more importantly also in terms of sound.
The precision CNC milled parts are optically perfectly coordinated and lead the Debut PRO to its modern simple, elegant and unprecedented design. The nickel finish of all these aluminium components result in a hard, resistant surface. This process enables us to produce very high-quality and sustainable components and avoid plastics and similar materials that continue to age over time and would more importantly also degrade sound quality.

The tonearm bearing is a completely new design. Precision CNC'd out of a single block of aluminium, you can see all the production stages above. The last step is putting a nickel finish on it. This will increase the rigidity of the bearing, ensuring free and fluid movement of the tonearm and precise tracking without material degration in looks or function.

DEEPLY DRIVEN
The electronically regulated synchronous motor drives the platter and guarantees the most accurate and stable speeds. Change between them easily with the toggle switch. With the supplied round belt for 78 rpm you can also listen to your shellac records.

A NEW PLATTER – A DEEPPER DISH
The new Debut PRO platter is a first on any Pro-Ject turntable. It features a notch for the record label and together with our Record Puck PRO (available separately) the puck's weight will press your record tightly against the platter. The die-cast aluminium platter is reworked and precision balanced in an extra step to obtain an evenly spinning platter. It is anti-magnetic, allowing MC cartridges to work properly. Delve deep into the vast upgrade path the Debut PRO has to offer!
The anti-magnetic heavy aluminium platter has a ring made of TPE (thermoplastic elastomer) on the inside that helps to dampen all resonances and minimizes wow and flutter. Our seperately available Record Puck PRO provides an extra level of damping and stability, so it is the perfect add-on for the Debut PRO.

HYBRID TONEARM
The new Debut PRO features a one-piece carbon-aluminium sandwich tonearm. The carbon layer gives the tonearm a high degree of rigidity, while the inner aluminium tube takes over the damping of the tonearm. This makes the tonearm perfect to be upgraded with higher-end MC cartridges!

AZIMUTH & VTA ADJUSTMENT
The newly designed tonearm base allows you to adjust both the azimuth and the vertical tracking angle (VTA). The tonearm height can be continuously adjusted by loosening the two grub screws. These settings give you the option of adapting the tonearm to height changes allowing the use of different turntable mats or other cartridges to always achieve the best sound quality. Setting and experimenting with the VTA & Azimuth is crucial in extracting every last bit of performance out of your cartridges.

Features:
Pick it PRO
Lively and robust sound
The perfect combination of components is the key to achieve the great sound of the Pick it PRO.

Nickel Coating
Sustainable components
The nickel finish of the aluminium components results in a hard, resistant surface.

Hybrid Tonearm
Carbon Aluminium Sandwich
This super stiff and uniquely dampened tonearm ensures perfect tracking of the record groove.

VTA & Azimuth
Fully adjustable
The Debut PRO comes with fully adjustable Azimuth & VTA. It offers you the possibility to modify your turntable as you want it.

33/45/78 RPM
High precision motor control
The playback speeds are electronically controlled with precision, which guarantees the most accurate and stable music reproduction. Change between speeds easily with the toggle switch.

Bearing block
Complete new design
The precision CNC milled and nickel coated tonearm bearing parts are completely new and designed just for the PRO.

Special Platter
TPE damped & anti magnetic
The heavy aluminium platter has a ring made of TPE (thermoplastic elastomer) on the inside that helps to dampen all resonances and minimizes wow and flutter.

Metal Feet
Damped & height adjustable
The three height adjustable damped aluminium feet guarantee the perfect stand & massively reduce risk of acoustical feedback.

Technical Specifications:
• Speed: 33, 45/(78) (electronic speed change)
• Drive principle: belt drive with electronic speed control
• Platter: 300mm, die cast aluminium platter with TPE damping and felt mat
• Platter bearing: high precision stainless steel axle in bronze bushing
• Wow & flutter: 33: +/-0,16%; 45: +/-0,14%
• Speed drift: 33: +/-0,40%; 45: +/-0,50%
• Signal to noise: 68dB
• Tonearm: 8,6” one-piece carbon-aluminium tonearm
• Effective arm length/mass: 218,5 mm / 10,0 g
• Overhang: 18,5mm
• Included accessories: 15V DC / 0,8A power supply, dust cover, 78 RPM round belt, 7‘‘ single adapter
• Power consumption: 4W / 0W standby
• Dimensions: 415 x 113 x 320mm (WxHxD)
• Weight: 6 kg net

Manual: https://www.project-audio.com/wp-content/uploads/2021/07/PJ-Phono-DebutPro-Manual.pdf

With our practical index, you can finally bring order to your vinyl collection. No matter how big your collection is - with the separating register you can keep an overview. The 13 wooden registers are printed alphabetically and are simply inserted between the records.
The indexes are 2.5 mm thick, 36 cm high and 6 cm wide, printed on both ends and made of high-quality plywood. They can be used vertically and horizontally.
As part of the Vinyl Care by HHV product range, the record dividers were developed for passionate vinyl collectors who are looking for simple and high-quality utensils for the care and storage of their records.

Lightweight 45" bag holds about 50 of your favorite PPU singles.

Lightweight 45" bag holds about 50 of your favorite PPU singles.

High quality 12" professional grade slipmat. Ideal for scratching and turntablists. Provides durability and will not scuff or damage vinyl.

• Made out of a smooth but strong material
• Unique matte surface
• Far more resistant to dust and other particles
• Extra thin and provide optimum feel for DJs
• Comes in pairs packaged inside a sleeve

Awesome logo design developed in collaboration with DJ ND and Maxime Bouchat, Graphic Designer, Blue Marine Productions Associées.

The Super OM 5E major improvements:
1. By means of computer simulations it has been possible to define the natural pivot point of the system with unprecedented accuracy while achieving an optimum oscillation balance. The result: improved linearity, higher channel separation and reduced distortion.

2. OM Super cartridges models have split pole PINs which reduces magnetic losses at the treble end. This technology extends the frequency range and improves phase linearity.

3. OM Super 5 cartridge body is manufactured from a Noryl (plastic & glass compound) which ensures high rigidity and freedom from resonances.

Optimal fit and sound reproduction
If your tonearm has a standard headshell or a cartridge mount, then step up to optimal sound reproduction with OM’s. A glance at anyone of these cartridges will reveal Ortofon's answer to perfect tonearm matching. Ingeniously tucked into the top of the mounting bracket is a tiny, removable weight-plate.

If your tonearm is an standard tonearm, just leave the weight-plate. If your tonearm is one of the low mass types, then simply remove the weight. The mass of your OM cartridge is now a mere 2.5g.

Super OM 5E features Elliptical stylus that provides balanced and distortion-free playback. Elliptical diamonds are able to follow the groove oscillations more accurately than spherical diamonds due to their contoured shape. This results in better tracking and less distortion.

Super OM 5 Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 22 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 3 / -3
• Tracking ability at 315Hz at recommended tracking force - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17.5 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1 kOhm
• Internal inductance - 580 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 200-500 pF
• Cartridge colour, body/stylus - Black/Black
• Cartridge weight incl. extra weight - 5 g
• Cartridge weight excl. extra weight - 2.5 g
• Replacement stylus unit - Stylus 5 E, Stylus 10

Styli types and interchangeability
The OM 5s features a Spherical diamond. Spherical diamonds are the simplest and most robust diamonds. The OM 5E and Super OM 5E feature an Elliptical diamond.

In the development of OM cartridges, a major objective was to provide the music lover with the opportunity to optimize sound reproduction without having to replace the entire cartridge. Instead of being merely intended for replacement purposes following wear or damage, the OM 5 Series allows you to step up to better sound by simply upgrading the stylus.

Depending on your preference, styli for the OM 5 Series are easily interchanged and include: styli 3E, 5E, 10, 20, 30, 40 & 78 and D 25 M.

The new Ortofon OM 5 series encompasses three basic cartridges: OM 5S, OM 5E and Super OM 5E.
• The series is the lowest-mass range of moving magnet cartridges offered by Ortofon.
• The OM cartridges bodies have been designed to provide easy mounting and alignment on both top mount and bottom mount headshells.
• The OM 5 Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

Styli protection caps for VNL cartridges and styli

The stylus protection guard helps to limit stylus damage, if the cartridge accidentally slides across a record or if the cartridge is dropped onto the record.

The protection caps come in pairs.

Stylus guard (1 Pcs.)

Technical specifications:
• Frequency response - 20-18.000 Hz + 2 / - 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 70 µm
• Compliance, dynamic, lateral - 7 µm/mN
• Stylus type - Spherical
• Stylus tip radius - R 25µm
• Tracking force range - 2.0-3.0 g (20-30 mN)
• Tracking force, recommended - 2.5 g (25 mN)
• Tracking angle - 20°
• Stylus colour - Black
• Recommended for following cartridges: all Super OM, OM, OMP, TM, Concorde cartridges for playing micro-groove records.
*) Typical value

Technical specifications:
• Frequency response - 20-12.000 Hz + 2 / - 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 15 µm/mN
• Stylus type - Spherical
• Stylus tip radius - 65µm
• Tracking force range - 1.75-2.25 g (17.5-22.5 mN)
• Tracking force, recommended - 2.0 g (20 mN)
• Tracking angle - 20°
• Stylus colour - Black
• Recommended for following cartridges: all Super OM, OM, OMB, OMP, TM, Concorde STD cartridges for playing 78 r.p.m. records
*) Typical value

Technical specifications:
• Frequency response: 20-18.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force *): 60 µm
• Compliance, dynamic, lateral: 25 µm/mN
• Stylus type: Elliptical
• Stylus tip radius: r/R 8/18 µm
• Tracking force range: 1.0-1.5 g (10-15 mN)
• Tracking force, recommended: 1.25 g (12.5 mN)
• Tracking angle: 20°
• Stylus colour: Black
• Recommended for TM 7 and TM 7U cartridges models
*) Typical value

Technical specifications:
• Frequency response - 20-20.000 Hz + 2 / - 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Spherical
• Stylus tip radius - R 18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17,5 mN)
• Tracking angle - 20°
• Stylus colour - Black
• Recommended for OM 5S and OM 1S
*) Typical value

Technical specifications:
• Frequency response - 20-20.000 Hz + 3 /- 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.25-1.75 g (12.5-17.5 mN)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Stylus colour - Black
• Recommended for Series 500 Mkll, 510, 510 P, Alfa
*) Typical value

Technical specifications:
• Frequency response - 20-18.000 Hz + 2 / - 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17.5 mN)
• Tracking angle - 20°
• Stylus colour - Black
• Recommended for OM 3E, OMP 3E, OMB 3E
*) Typical value

Technical specifications:
• Frequency response - 20-20.000 Hz + 3 /- 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.25-1.75 г (12.5-17.5 мН)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Stylus colour - Grey
• Recommended for Series 310 Universal
*) Typical value

Technical specifications:
• Frequency response - 20-20.000 Hz + 2 / - 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Spherical
• Stylus tip radius - R 18 µm
• Tracking force range - 1.25-1.75 g (12.5-17.5 mN)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Stylus colour - Grey
• Recommended for Series 305 Universal
*) Typical value

Technical specifications:
• Frequency response - 20-20.000 Hz + 2 / - 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 70 µm
• Compliance, dynamic, lateral - 25 µm/mN
• Stylus type - Nude Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.25-1.75 g (12.5-17.5 mN)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Stylus colour - Black
• Recommended for following cartridges: Super OM 20, OM 20, OMP 20, OMB 20, LM 20, Concorde 20, LM 20H, TM 20U, TM 20H
*) Typical value

Technical specifications:
• Frequency response: - 20-20.000 Hz + 2 / - 2 dB
• Tracking ability at 315Hz at recommended tracking force*): 70 µm
• Compliance, dynamic, lateral: 25 µm/mN
• Stylus type: Elliptical
• Stylus tip radius: r/R 8/18 µm
• Tracking force range: 1.0-1.5 g (10-15 mN)
• Tracking force, recommended: 1.25 g (12.5 mN)
• Tracking angle: 20°
• Stylus colour: Black
• Recommended for TM 14U
*) Typical value

Ortofon SH-4 headshells are high-quality, solid headshells for variety of applications

The SH-4 headshell has an ergonomic design with a long finger that is easy to pick-up. The big finger grip and shorter construction makes movement and placement of the headshell easy and visible.
The wire terminals on the rear side are also gold plated for better signal transmission.

Dimensions and weight:
• Weight: 9.4g
• Shell length: 51.5mm
• Finger Length: 27mm

The SH-4 comes with leadwires for easy and convenient connection
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell.

Ortofon SH-4 headshell PINs and Ortofon cartridges' terminal PINs diameter is 1.2 mm. Leadwires supplied fit all right on the cartridges' terminal PINs.

Screws for mounting 2M cartridges on the headshell incl.:
• 2x 2.5x5mm
• 2x 2.5x7mm

The new Ortofon Reference Interconnect cables Series is designed and manufactured by Ortofon Japan
Each of the new Reference series cables has its individual sonic expression:

- The Reference Red is an all-purpose, decent, but not too expensive cable that would be a great addition to any audio equipment. The sound is relaxed, warm and dynamic with high resolution.
- The Reference Blue is a dynamic and high-resolution cable that reveals detailed reproduction throughout the spectrum.
- The Reference Bronze has an astonishing wide-range, clear and neutral sound.
- The Reference Black is a new generation reference audio cable par excellence with a well-balanced, neutral and precise sound.

Ortofon Reference Red cable
The Reference Red Interconnect cable is a perfect combination of 4N OFC (Oxygen-free copper) and 4N HiFC (High performance pure copper) conductors. These two copper conductor materials are combined to create a warm, dynamic sound with high resolution.
The Reference Red is surrounded by shield of both 16 sets of 0.1mm x 10 copper wires and aluminum to reduce electromagnetic induced noise.
The gold plated RCA terminals provide easy, stable and durable connection.

• Cable capacity: 190pF/m
• Cable length: 1.0 m or 1.5 m
• Terminal type: RCA
• 2 pieces per set

Reference Red technical configuration
① Signal conductors:
• OFC (Oxygen-free copper) Ø 0.5 mm + Ø 0.32 mm × 7
• HiFC (High performance pure copper) Ø 0.12 mm × 28
② Signal conductors:
• OFC (Oxygen-free copper) Ø 0.5 mm + Ø 0.32 mm × 7
• HiFC (High performance pure copper) Ø 0.12 mm × 28
③ Damping material: Cotton fiber
④ Shield: Aluminuim tape
⑤ Shield: Braided Tin-plated 3N copper wire Ø 0.1 mm × 10 × 16
⑥ Insulation: Halogen-free highly resilient elastomer
⑦ Cable diameter: 7.5 mm
⑧ Insulation: PE

Tool for OM mounting

The OM 5S is a moving magnet cartridge for general purpose application
If your tonearm has a standard headshell or a cartridge mount, then step up to optimal sound reproduction with OM’s. A glance at anyone of these cartridges will reveal Ortofon's answer to perfect tonearm matching. Ingeniously tucked into the top of the mounting bracket is a tiny, removable weight-plate.

If your tonearm is an standard tonearm, just leave the weight-plate. If your tonearm is one of the low mass types, then simply remove the weight. The mass of your OM cartridge is now a mere 2.5 g.

The OM 5S features Spherical stylus, robust and economic solution for play back of vinyl records.

For more than 50 years, Ortofon has been designing and manufacturing Moving Magnet cartridges. Along with our well-regarded Moving Coil cartridges, Moving Magnet models have established a good reputation among music lovers and Hi-Fi enthusiasts the world over.

The new Ortofon OM 5 series encompasses three basic cartridges: OM 5S, OM 5E and Super OM 5E.
• The series is the lowest-mass range of moving magnet cartridges offered by Ortofon.
• The OM cartridges bodies have been designed to provide easy mounting and alignment on both top mount and bottom mount headshells.
• The OM 5 Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

OM 5S Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4.5 mV
• Channel balance at 1 kHz - 2 dB
• Channel separation at 1 kHz - 20 dB
• Channel separation at 15 kHz - 12 dB
• Frequency response - 20-22.000 Hz
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Spherical
• Stylus tip radius - R 18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17.5 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 750 Ohm
• Internal inductance - 450 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 200-500 pF
• Cartridge colour, body/stylus - Black/Black
• Cartridge weight incl. extra weight - 5 g
• Cartridge weight excl. extra weight - 2.5 g
• Replacement stylus unit - Stylus 5S
*) Typical value

Styli types and interchangeability
By adopting a wide range of replacement styli, the OM 5 Series can provide an optimum match for your home system, application and budget.
In the development of OM cartridges, a major objective was to provide the music lover with the opportunity to optimize sound reproduction without having to replace the entire cartridge. Instead of being merely intended for replacement purposes following wear or damage, the OM 5 Series allows you to step up to better sound by simply upgrading the stylus. Depending on your preference, styli for the OM 5 Series are easily interchanged and include: styli 3E, 5E, 10, 20, 30, 40 & 78 and D 25 M.

Optimal fit and sound reproduction
If your tonearm has a standard headshell or a cartridge mount, then step up to optimal sound reproduction with OM’s. A glance at anyone of these cartridges will reveal Ortofon's answer to perfect tonearm matching. Ingeniously tucked into the top of the mounting bracket is a tiny, removable weight-plate.

If your tonearm is an standard tonearm, just leave the weight-plate. If your tonearm is one of the low mass types, then simply remove the weight. The mass of your OM cartridge is now a mere 2.5g.

OM 5E features Elliptical stylus that provides balanced and distortion-free playback. Elliptical diamonds are able to follow the groove oscillations more accurately than spherical diamonds due to their contoured shape. This results in better tracking and less distortion.

• OM 5E Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4 mV
• Channel balance at 1 kHz - 2 dB
• Channel separation at 1 kHz - 22 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 3 / -3
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17.5 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 750 Ohm
• Internal inductance - 450 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 200-500 pF
• Cartridge colour, body/stylus - Black/Black
• Cartridge weight incl. extra weight - 5 g
• Cartridge weight excl. extra weight - 2.5 g
• Replacement stylus unit - Stylus 5E
*) Typical value

Styli types and interchangeability
By adopting a wide range of replacement styli, the OM 5 Series can provide an optimum match for your home system, application and budget.
In the development of OM cartridges, a major objective was to provide the music lover with the opportunity to optimize sound reproduction without having to replace the entire cartridge. Instead of being merely intended for replacement purposes following wear or damage, the OM 5 Series allows you to step up to better sound by simply upgrading the stylus. Depending on your preference, styli for the OM 5 Series are easily interchanged and include: styli 3E, 5E, 10, 20, 30, 40 & 78 and D 25 M.

Enter the Exclusive world of Ortofon’s famous moving coil sound!
The Quintet Red is a perfect introduction to the world of Ortofon moving coils.
It features an Elliptical diamond which is cut and polished to Ortofon’s standards.

This entry-level MC cartridge has very high price-to-performance ratio and is a perfect all-rounder for the newcomers to the world of Moving Coil cartridges.

MC Quintet Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth.

The ST-7 transformer is a perfect match for the MC Quintet Red cartridge.

LH-4000 headshell is specially recommended for MC Quintet cartridges series.

MC Quintet Red Technical data:
• Output voltage at 1 kHz 5 cm/sec - 0.5 mV
• Channel balance - < 1.5 dB
• Channel separation at 1 kHz - > 21 dB
• Channel separation at 15 kHz - > 14 dB
• Frequency response 20-20.000 Hz - +/-2.5 dB
• Tracking ability at 315 Hz at recommended tracking force *) - 65 μm
• Compliance, dynamic, lateral - 15 μm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 μm
• Tracking force range - 2.1-2.5 g (21-25 mN)
• Tracking force recommended - 2.3 g (23 mN)
• Tracking angle - 20º
• Internal impedance, DC resistance - 7 Ohm
• Recommended load impedance - >20 Ohm
• Cartridge body material - ABS/Aluminium
• Coil wire material - Copper
• Cartridge colour - Red
• Cartridge weight - 9 g
*) Typical value

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for Quintet cartridge.

Ease of use
Top-mounting of the Quintet cartridges is easy and secure using the screws supplied. The aluminuim frame has threaded mounting holes and is fitted easily with the 5mm or 7mm screws depending on the thickness of the headshell.

The Quintet series’ right angles, straight lines, stylus visibility and ample distance between the record surface and the cartridge’s bottom will make it easy to mount and align the cartridge and tonearm correctly. The Quintet Series gives excellent results with most common tonearms.

LW-800S is the most sophisticated lead wires composed of Pure Silver and Silver coated wire.
The end of wire is fastened by Rhodium plated terminal.
Since Silver has the best electrical conductive properties of all the metals, the LW-800S silver wire is able to transmits the very clear high tone signals, which brings the brilliant tonality to the sound reproduction.

Technical data:
• 4N Pure Silver wire: 3 x φ 0.26mm
• Silver plated Oxygen Free Copper (OFC) wire: 16 x φ0.10mm

Mounting instructions:
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell. Please remember correct orientation of the leads. Ortofon SH-4 headshell and Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is normally only 1.0 mm.

Using LW 8N with the SH-4 headshell requies the LW 8N shell side clamp to be widened a little bit to fit on the SH-4 PINs. If shifted around, it may cause over-tightening of the assembly. Being aware about this detail, you will avoid the risk of having the cartridge's terminal PINs fall out.

Luxury leadwireset
LW-7N is the hybrid lead wire made of Ultra High Purity Copper wire of 7N and 6 N. The end of wire is fastened by Rhodium plated terminal.
As there is no foreign particle other than Copper 7N (99.99999 % purity) in the wire, music signal can be transmitted without any noise.

Technical data:
• High purity Cu wire 7NCu: 3 x φ 0.26mm
• High purity Cu wire 6NCu: 16 x φ0.10mm

Mounting instructions:
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell. Please remember correct orientation of the leads. Ortofon SH-4 headshell and Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is normally only 1.0 mm.

Using LW 7N with the SH-4 headshell requies the LW 7N shell side clamp to be widened a little bit to fit on the SH-4 PINs. If shifted around, it may cause over-tightening of the assembly. Being aware about this detail, you will avoid the risk of having the cartridge's terminal PINs fall out.

Luxury leadwireset
LW-6N is the 6N lead wire made of Ultra High Purity Copper wire.
The configuration is very sofisticated with different diameter of wire strand, the inside strand is right windings, the outside strand is left winding. The end of wire is fastened by gold plated terminal.
The tight winding against each other makes the clear transmission of music signals. Clear and crisp tonality.

Technical data:
• High purity Cu wire 6NCu: 7 x φ 0.18mm (Right strands)
• High purity Cu wire 6NCu: 17 x φ 0.10mm (Left strands)

Mounting instructions:
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell. Please remember correct orientation of the leads. Ortofon SH-4 headshell and Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is normally only 1.0 mm.

Using LW 6N with the SH-4 headshell requies the LW 6N shell side clamp to be widened a little bit to fit on the SH-4 PINs. If shifted around, it may cause over-tightening of the assembly. Being aware about this detail, you will avoid the risk of having the cartridge's terminal PINs fall out.

The LH-4000 is a basic high quality headshell designed specifically for HiFi applications. Providing a clean, minimalist aesthetic, the LH-4000 is great for a wide variety of cartridges, specially recommended for the MC Quintet series.

Special features:
• Azimuth adjustable, which is beneficial for optimal channel separation
• Ergonomic fingerlift for easy handling
• Knowing the fundamental headshell dimensions will in a lot of cases make it easier to mount and align cartridge and tonearm correctly. Please scroll to the bottom of the page to see the headshells mounting dimensions chart.

The LH-4000 comes with leadwires for easy and convenient connection
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell.

Please remember correct orientation of the leads. Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is only 1.0 mm.

Features and Technical data:
• Universal mount
• Solid aluminum build
• Azimuth adjustable by means of hexagon wrench
• PIN conductor - Gold plated
• Weight - 14.3 grams without screws
• Mounting distance min. - 39.5 mm
• Mounting distance max. - 45.6 mm
• Headshell length - 51.9 mm
• Headshell width - 19.1 mm

The LH-2000 is a basic high quality headshell designed specifically for HiFi applications. Providing a clean, minimalist aesthetic, the LH-2000 is great for a wide variety of cartridges, e.g. the 2M Series .

Knowing the fundamental headshell dimensions will in a lot of cases make it easier to mount and align cartridge and tonearm correctly. Please scroll to the bottom of the page to see the headshells mounting dimensions chart.

The LH-2000 comes with leadwires for easy and convenient connection
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell.

Please remember correct orientation of the leads. Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is only 1.0 mm.

Features and Technical data:
• Universal mount
• Solid aluminum build
• Weight without screws - 15.5 grams
• Mounting distance - min 35.3 mm, max 43.4 mm
• Headshell length - 50.3 mm
• Headshell width - 20.0 mm

High quality 12" professional grade slipmat. Ideal for scratching and turntablists. Provides durability and will not scuff or damage vinyl.

• Made out of a smooth but strong material
• Unique matte surface
• Far more resistant to dust and other particles
• Extra thin and provide optimum feel for DJs
• Comes in pairs packaged inside a sleeve

Awesome 3D design
The VNL 3D design is developed in collaboration with DJ ND and Maxime Bouchat, Graphic Designer, Blue Marine Productions Associées.

The slipmat design uses several elements linked to the DJ culture:
• Scissors stand for "Cutting sounds"
• Equalizer levels picture refers to the mixers' levels
• Spiral symbolises turntable platter when spinning

The effect of animation is fully obtainable when the pitch is set to 33 +8.

Comprises 1 PC carbon fibre stylus brush and 1 PC screwdriver in a plastic cylinder.

High quality 12" professional grade slipmat. Ideal for scratching and turntablists. Provides durability and will not scuff or damage vinyl.

• Made out of a smooth but strong material
• Unique matte surface
• Far more resistant to dust and other particles
• Extra thin and provide optimum feel for DJs
• Comes in pairs packaged inside a sleeve

Awesome logo design developed in collaboration with DJ ND and Maxime Bouchat, Graphic Designer, Blue Marine Productions Associées.

High quality 12" professional grade slipmat. Ideal for scratching and turntablists. Provides durability and will not scuff or damage vinyl.

• Made out of a smooth but strong material
• Unique matte surface
• Far more resistant to dust and other particles
• Extra thin and provide optimum feel for DJs
• Comes in pairs packaged inside a sleeve

Awesome logo design developed in collaboration with DJ ND and Maxime Bouchat, Graphic Designer, Blue Marine Productions Associées.

2MR: the newest addition to the renowned 2M Series
Ortofon 2MR features a specially designed cartridge housing tailored for turntables and tonearms like Rega matching their requirement for low-form factor cartridges. With its narrow cartridge housing, it seamlessly integrates without a need for modifications or spacers under the tonearm, enabling quick and easy mounting with just two screws. Ortofon 2MR cartridges features unique to Ortofon technologies like: High-performance quad coil motor system with split pole pins, Proprietary Ortofon premium and high-end rubber dampers plus full compatibility with the Ortofon 2M series styli.

Authentic sound reproduction
2MR continues the 2M Series' commitment to authentic sound reproduction.
A high-performance motor system featuring quad coils and split pole pins minimizes eddy current losses, enhancing channel balance and accuracy.
This innovation results in a clean, detailed, and true-to-life sound, faithfully capturing the nuances of your cherished vinyl collection.

More than just a cartridge
2MR cartridge are for those who value an authentic immersive listening experience when listening to their music. 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.
The 2MR maintains the hallmark of interchangeability, allowing you to explore your records in greater depth and detail. The seamless transition between stylus profiles lets you tailor your listening experience, ensuring every note is heard with unparalleled accuracy and emotion. The 2MR series empowers you to explore your records like never before, allowing you to savor every moment of your favorite music.
The 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.

2MR cartridge key features:
• Slimline cartridge body effectively eliminates the need for tonearm spacers, shims or modifications on turntables needing a low form factor cartridge.
• High-performance motor system incorporating unique to Ortofon quad coils with split pole pins, delivering a clean detailed and true-to-life sound.
• 100% compatibility with the 2M styli Ortofon 2MR use the well-known 2M styli.
• Standard half inch mounting quick and easy mounting on the tonearms with just two screws.
• Full range setup 2MR ranges from Mono to Premium: 2MR Red to High-end: 2MR Black LVB 250

Step into the music with the 2M Red
With the 2M Red you will hear the music come to life on its own terms. It is like taking a step into music itself. This is our entry-level cartridge in the series, but what an entry.

Featues:
The 2M Red features a tipped Elliptical diamond and split pole pins with a copper wire.
The engine provides an increased output of 5.5 mV and an optimized sound reproduction and a high level of sonic accuracy.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Red delivers an open, dynamic sound with a slight touch of warmth.

Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 22 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 70 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Red
• 2MR cartridge weight - 6 g
• 2M and 2M Verso cartridges weight - 7.2 g
• 2M Premounted cartridge weight - 16.7 g

Replacement stylus unit - 2M Red (interchangeable with 2M Blue and 2M Silver)

Stylus lifetime:
with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

2MR: the newest addition to the renowned 2M Series
Ortofon 2MR features a specially designed cartridge housing tailored for turntables and tonearms like Rega matching their requirement for low-form factor cartridges. With its narrow cartridge housing, it seamlessly integrates without a need for modifications or spacers under the tonearm, enabling quick and easy mounting with just two screws. Ortofon 2MR cartridges features unique to Ortofon technologies like: High-performance quad coil motor system with split pole pins, Proprietary Ortofon premium and high-end rubber dampers plus full compatibility with the Ortofon 2M series styli.

Authentic sound reproduction
2MR continues the 2M Series' commitment to authentic sound reproduction.
A high-performance motor system featuring quad coils and split pole pins minimizes eddy current losses, enhancing channel balance and accuracy.
This innovation results in a clean, detailed, and true-to-life sound, faithfully capturing the nuances of your cherished vinyl collection.

More than just a cartridge
2MR cartridge are for those who value an authentic immersive listening experience when listening to their music. 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.
The 2MR maintains the hallmark of interchangeability, allowing you to explore your records in greater depth and detail. The seamless transition between stylus profiles lets you tailor your listening experience, ensuring every note is heard with unparalleled accuracy and emotion. The 2MR series empowers you to explore your records like never before, allowing you to savor every moment of your favorite music.
The 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.

2MR cartridge key features:
• Slimline cartridge body effectively eliminates the need for tonearm spacers, shims or modifications on turntables needing a low form factor cartridge.
• High-performance motor system incorporating unique to Ortofon quad coils with split pole pins, delivering a clean detailed and true-to-life sound.
• 100% compatibility with the 2M styli Ortofon 2MR use the well-known 2M styli.
• Standard half inch mounting quick and easy mounting on the tonearms with just two screws.
• Full range setup 2MR ranges from Mono to Premium: 2MR Red to High-end: 2MR Black LVB 250

Bona fide precision with the 2M Bronze
To us hi-fi is more than a fancy label. High fidelity is the goal of everything we do. The 2M Bronze is designed to give the music a whole new dimension of precision. Listening to your records with the 2M Bronze is like hearing them for the first time and you get to fall in love with the songs all over. That is what hi-fi means to us and that is what you get with the 2M Bronze.

Features:
The 2M Bronze features a Nude Fine Line diamond, which is particularly suited for demanding applications. The slim profile of the Fine Line stylus will track even the highest frequency information. Additionally, its larger footprint ensures reduced distortion and record wear. The 2M Bronze uses a special upgraded engine, featuring split pole pins with a silver plated copper wire.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5 mV
• Channel balance at 1 kHz - 1 dB
• Channel separation at 1 kHz - 26 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 + 2 / - 0 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 22 µm/mN
• Stylus type - Nude Fine Line
• Stylus tip radius - r/R 8/40 µm
• Tracking force range - 1.4-1.7 g (14-17 mN)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.2 kOhm
• Internal inductance - 630 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Bronze
• 2MR cartridge weight - 6 g
• 2M and 2M Verso cartridges weight - 7.2 g
• 2M Premounted cartridge weight - 16.7 g

Replacement stylus unit - 2M Bronze (interchangeable with 2M Black and 2M Black LVB 250)

Stylus lifetime:
with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

2MR: the newest addition to the renowned 2M Series
Ortofon 2MR features a specially designed cartridge housing tailored for turntables and tonearms like Rega matching their requirement for low-form factor cartridges. With its narrow cartridge housing, it seamlessly integrates without a need for modifications or spacers under the tonearm, enabling quick and easy mounting with just two screws. Ortofon 2MR cartridges features unique to Ortofon technologies like: High-performance quad coil motor system with split pole pins, Proprietary Ortofon premium and high-end rubber dampers plus full compatibility with the Ortofon 2M series styli.

Authentic sound reproduction
2MR continues the 2M Series' commitment to authentic sound reproduction.
A high-performance motor system featuring quad coils and split pole pins minimizes eddy current losses, enhancing channel balance and accuracy.
This innovation results in a clean, detailed, and true-to-life sound, faithfully capturing the nuances of your cherished vinyl collection.

More than just a cartridge
2MR cartridge are for those who value an authentic immersive listening experience when listening to their music. 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.
The 2MR maintains the hallmark of interchangeability, allowing you to explore your records in greater depth and detail. The seamless transition between stylus profiles lets you tailor your listening experience, ensuring every note is heard with unparalleled accuracy and emotion. The 2MR series empowers you to explore your records like never before, allowing you to savor every moment of your favorite music.
The 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.

2MR cartridge key features:
• Slimline cartridge body effectively eliminates the need for tonearm spacers, shims or modifications on turntables needing a low form factor cartridge.
• High-performance motor system incorporating unique to Ortofon quad coils with split pole pins, delivering a clean detailed and true-to-life sound.
• 100% compatibility with the 2M styli Ortofon 2MR use the well-known 2M styli.
• Standard half inch mounting quick and easy mounting on the tonearms with just two screws.
• Full range setup 2MR ranges from Mono to Premium: 2MR Red to High-end: 2MR Black LVB 250

Next level authenticity with the 2M Blue
The goal for any cartridge should be to reproduce the sound as close to the artists vision as possible, and the 2M blue takes you further on this journey of authenticity. With the 2M Blue, you get serious about listening to vinyl.

Features:
The 2M Blue features a Nude Elliptical diamond and split pole pins with a copper wire.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

The 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details compared to the 2M Red model.

Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 25 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 2 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Nude Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Blue
• 2MR cartridge weight - 6 g
• 2M and 2M Verso cartridges weight - 7.2 g
• 2M Premounted cartridge weight - 16.7 g

Replacement stylus unit - 2M Blue (interchangeable with 2M Red and 2M Silver)

Stylus lifetime:
with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

Step into the music with the 2M Red
With the 2M Red you will hear the music come to life on its own terms. It is like taking a step into music itself. This is our entry-level cartridge in the series, but what an entry.

Featues:
The 2M Red features a tipped Elliptical diamond and split pole pins with a copper wire.
The engine provides an increased output of 5.5 mV and an optimized sound reproduction and a high level of sonic accuracy.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Red delivers an open, dynamic sound with a slight touch of warmth.

2M Red Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 22 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 70 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Red
• 2M standard and 2M Verso cartridges weight - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M Red (interchangeable with 2M Blue and 2M Silver)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze, 2M Black and 2M Black LVB 250
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

With the 2M Premounted, it’s never been easier to experience.
The 2M Premounted is a practical and elegant solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm. The quality of the SH-4 headshell is sturdy and rigid, yet the design emphasizes a slim and delicate form factor. The strong, lightweight headshell has an ergonomic design with a long finger lift that is easy to pick up.

Features:
- Premounted on our popular SH-4 Black headshell.
- Easy and direct mount on S-shaped tonearms with universal mount.
- Correct Baerwald alignment with tonearms with universal mount.

Bona fide precision with the 2M Bronze
To us hi-fi is more than a fancy label. High fidelity is the goal of everything we do. The 2M Bronze is designed to give the music a whole new dimension of precision. Listening to your records with the 2M Bronze is like hearing them for the first time and you get to fall in love with the songs all over. That is what hi-fi means to us and that is what you get with the 2M Bronze.

Features:
The 2M Bronze features a Nude Fine Line diamond, which is particularly suited for demanding applications. The slim profile of the Fine Line stylus will track even the highest frequency information. Additionally, its larger footprint ensures reduced distortion and record wear. The 2M Bronze uses a special upgraded engine, featuring split pole pins with a silver plated copper wire.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Bronze Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5 mV
• Channel balance at 1 kHz - 1 dB
• Channel separation at 1 kHz - 26 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 + 2 / - 0 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 22 µm/mN
• Stylus type - Nude Fine Line
• Stylus tip radius - r/R 8/40 µm
• Tracking force range - 1.4-1.7 g (14-17 mN)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.2 kOhm
• Internal inductance - 630 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Bronze
• Cartridge weight - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M Bronze (interchangeable with 2M Black and 2M Black LVB 250)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze, 2M Black and 2m Black LVB 250
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

With the 2M Premounted, it’s never been easier to experience
The 2M Premounted is a practical and elegant solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm. The quality of the SH-4 headshell is sturdy and rigid, yet the design emphasizes a slim and delicate form factor. The strong, lightweight headshell has an ergonomic design with a long finger lift that is easy to pick up.

Features:
- Premounted on our popular SH-4 Black headshell.
- Easy and direct mount on S-shaped tonearms with universal mount.
- Correct Baerwald alignment with tonearms with universal mount.

Next level authenticity with the 2M Blue
The goal for any cartridge should be to reproduce the sound as close to the artists vision as possible, and the 2M blue takes you further on this journey of authenticity. With the 2M Blue, you get serious about listening to vinyl.

Features:
The 2M Blue features a Nude Elliptical diamond and split pole pins with a copper wire.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

The 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details compared to the 2M Red model.

2M Blue Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 25 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 2 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Nude Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Blue
• Cartridge weight - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M Blue (interchangeable with 2M Red and 2M Silver)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze, 2M Black and 2M Black LVB 250
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

With the 2M Premounted, it’s never been easier to experience
The 2M Premounted is a practical and elegant solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm. The quality of the SH-4 headshell is sturdy and rigid, yet the design emphasizes a slim and delicate form factor. The strong, lightweight headshell has an ergonomic design with a long finger lift that is easy to pick up.

Features:
- Premounted on our popular SH-4 Black headshell.
- Easy and direct mount on S-shaped tonearms with universal mount.
- Correct Baerwald alignment with tonearms with universal mount.

The 2M 78 features an improved engine, which provides a high level of sonic accuracy. The stylus' tip is a Spherical diamond that is perfect for playback of 78 rpm shellac records, which require a larger stylus profile. The cartridge body is manufactured from Hopelex, which ensures high rigidity while eliminating unwanted resonances.

2M 78 uses a strapped output to deliver the same output signal from both sets of pole pins. This effectively eliminates the need for mono-specific equipment, making it possible to enjoy true mono reproduction on any stereo playback system.

The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M 78 Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4 mV
• Frequency response - 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 70 µm
• Compliance, dynamic, lateral - 18 µm/mN
• Stylus type - Spherical
• Stylus tip radius - R 65 µm
• Tracking force range - 1.6-2.0g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Internal impedance, DC resistance - 700 Ohm
• Internal inductance - 350 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Tracking angle - 20°
• Cartridge colour, body/stylus - Black/Grey
• Cartridge weight without screws - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M 78 (interchangeable with 2M Mono)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

Disc Flatter is long seller product and our signature item.This product flattens warped discs and returns them to
their original condition in just a few hours with automatic heating temperature adjustment function.

DF-01iA is the basic model and supports the disc has groove guard.

How the Disc Flattener Works.
Analog discs are made from polyvinyl chloride, commonly known as vinyl. Because of sensitivity to heat, the storage method you use for your analog vinyl records is important to avoid warps and other damage. Aging can also cause warping of vinyl records, and extra care should always be taken. By gently heating the record evenly and with a uniform pressure the vinyl can be returned to its original flat state without degrading the audio quality. Please note that SP records , heavy weight records, and flexi discs (also known as phonosheet or sooundsheet records) are not supported.

The Structure of Disc Flattener.
The Disc Flattener has semiconductor film applied in the top and bottom heaters of the unit allowing for a uniform heating process combined with an even pressure.

Specifications:
• Energy consumption : 160W
• Size : W：471mm
D：93mm
H：493mm
• Weight : About 11kg
• Environmental conditions used : Indoor normal temperature
(No condensation)
• Humidity : 20%～90%
(No condensation)
• Country of manufacture : Made in JAPAN

Disc Flattener is a long seller product and our signature item.This product flattens warped discs and returns them to
their original condition in just a few hours with automatic heating temperature adjustment function.

How the Disc Flattener Works.
Analog discs are made from polyvinyl chloride, commonly known as vinyl. Because of sensitivity to heat, the storage method you use for your analog vinyl records is important to avoid warps and other damage. Aging can also cause warping of vinyl records, and extra care should always be taken. By gently heating the record evenly and with a uniform pressure the vinyl can be returned to its original flat state without degrading the audio quality. Please note that SP records , heavy weight records, and flexi discs (also known as phonosheet or sooundsheet records) are not supported.

The Structure of Disc Flattener.
The Disc Flattener has semiconductor film applied in the top and bottom heaters of the unit allowing for a uniform heating process combined with an even pressure.

The ORB AUDIO DF-01i A+ is a meaningful further development of the DF-01i and was designed for all vinyl formats: singles, maxis, mini LPs and LPs. The device is able to heat corrugated records by a defined heating in three different temperature programs and to level the record again.

Waved records have a considerable influence on the optimal scanning process of the pickup system and lead to higher ambient noise, increased wear of the scanning needle and the sound carrier as well as poorer sound reproduction. Some records cannot be played back at all.

The ORB DF-01i A+ record iron heats up the vinyl, smoothes the surface and improves the conditions for an optimal scanning process. Pickups and records benefit from durability and quality. The heat treatment of the vinyl relaxes the material, which is very advantageous for the sound reproduction of the record. The differences in sound between wavy and smoothed vinyl are clearly noticeable. The ORB iron improves playback quality and preserves the value of your valuable pickups and vinyl treasures.

The ORB iron consists of a solid metal frame construction with two heating surfaces and an integrated timer at three temperature programs. The temperature programs Low, Medium and High are adjustable. The temperature program High is especially suitable for LP's with 180-200 grams. The Disc Flattener is designed for 7", 10" and 12" disc formats and is not suitable for shellac discs.

The + version comes with an adapter that also allows flat vinyl ironing.

Vinyls with groove guard with raised platemark are supported by both versions by default.

Specifications
• Energy consumption : 160W
• Size : W：471mm
D：93mm
H：493mm
• Weight : About 11kg
• Environmental conditions used : Indoor normal temperature
(No condensation)
• Humidity : 20%～90%
(No condensation)
• Country of manufacture : Made in JAPAN

Replacement stylus Nagaoka G JN-03D for the pickup DJ-03HD.

Replacement stylus for Shure M44G.

This product is a NAGAOKA produced and manufactured replacement stylus for the M44G, a cartridge widely used by DJs around the world. We have received many inquiries about a replacement stylus compatible with the M44G, since we had 'GD63-44G' in our lineup. After the production of 'GD63-44G' was discontinued, we reviewed the specifications and developed a new model. The new DJ-44G has a high sound pressure, delicate, wide-range, and powerful sound while keeping main features of toughness and solidity from the original M44G replacement.

Technical data
• Vertical tracking force: 2.0-3.5 g
• Material Cantilever: Aluminum alloy
• Material Stylus tip: 0.6 mil spherical bonded diamond
• Compatible cartridge: M44G/M44-7

DJ-03 HD - CARTRIDGE INCL. HEADSHELL

This is the Nagaoka DJ cartridge. With a high output voltage of 6 mV and a recommended tracking force of 3 - 5 g, it is one of the more stable of its kind.

TECHNICAL SPECIFICATIONS:
• Cartridge type: MM
• Configuration: Climax DS/DSM
• Output voltage: 6 mV (5 cm/sec.)
• Frequency Characteristics: 20Hz~20KHz
• Channel separation: 20 dB (1 kHz)
• Channel balance: 2 dB or less
• Load resistance: 47 kΩ
• Load: 100pF
• Cantilever: aluminum alloy
• Needle Tip: 0.6 mil tapered bonded diamond
• Recommended tracking force: 3~5g
• Pickup weight: 5.1g
• Weight with headshell: 15.1g