DJ Equipment 1257 Items

General purpose model for scratch and back-cueing

Great performance and durability as to basic scratch and back-cueing is what the Pro is known for. It has a good quality spherical stylus, a rock-solid cantilever, and serves general purposes well.

The Pro is the logical alternative to the more expensive expert carts. It offers both reasonable output and high sound quality which is, in fact, all there is needed to entertain an audience.

The Pro Series of cartridges provides a great balance of sound quality with tracking ability, for virtually any style of music.

Output voltage at 1000Hz, 5cm/sec.
5 mV
Channel balance at 1kHz
1,5 dB
Channel separation at 1kHz
20 dB
Channel separation at 15 kHz
15 dB
Frequency range at -3dB
20-20.000 Hz
Frequency response
20-20.000 Hz 3dB/-2dB
Tracking ability at 315 Hz at recommmende tracking force
70 μm
Compliance, dynamic lateral
7 μm/m N
Stylus type
Spherical
Stylus tip radius
R 18 μm
Tracking force range
3,0-5,0 g (30-50 mN)
Tracking force recommended
4,0 g (40 mN)
Tracking angle
20°
Internal impedance, DC resistance
750 Ohm
Internal inductance
450 mH
Recommended load resistance
47 kOhm
Recommended load capacitance
200-600 pF
PRO cartridge weight
18,5 g

Entry-level cartridge for all-purpose use

New DJ? This entry-level cartridge is perfect for newcomers on the DJ scene who want to start off with decent, but not too expensive equipment.

The Pro S has a spherical diamond stylus which minimizes scratching and a solid cantilever which can survive hectic activity at the turntable.

No matter what the application, the Pro S provides remarkable versatility for virtually any setting.

The sound quality is absolutely not to worry about. The Pro S is a consistent performer and a fine all-arounder!

Output voltage at 1000Hz, 5cm/sec.
5 mV
Channel balance at 1kHz
2 dB
Channel separation at 1kHz
20 dB
Channel separation at 15 kHz
15 dB
Frequency range at -3dB
20-20.000 Hz
Frequency response
20-18.000 Hz +/- 2 dB
Tracking ability at 315 Hz at recommmende tracking force
70 μm
Compliance, dynamic lateral
7 μm/m N
Stylus type
Spherical
Stylus tip radius
R 26 μm
Tracking force range
3,0-5,0 g (30-50 mN)
Tracking force recommended
4,0 g (40 mN)
Tracking angle
20°
Internal impedance, DC resistance
750 Ohm
Internal inductance
450 mH
Recommended load resistance
47 kOhm
Recommended load capacitance
200-600 pF
Cartridge weight
18,5 g

This UDG Record Bag is a medium size bag that holds up to 50 12 inch vinyl records. The U9500 is equipped with a removable shoulder strap (padded shoulder pad included), top handles, plus it's foam padded with PVC reinforced walls for extra protection.
Weight: approx. 1.2 kg.
Dimensions: approx. 34 x 29 x 35 cm (13.4 x 11.4 x 13.8 inch).
100% nylon, 840D.

Basic model for scratch and back-cueing. Outstanding rigidity by extra-strengthened cantilever

DJ S is a solid-built cartridge in a new blue nylon material. It has a fine spherical stylus and a special developed and extremely balanced cantilever.

Not only does the cartridge have a most sufficient tracking ability, it is also nearly unbreakable and provides the DJs with the most needed stringency. Furthermore, it equals very low record wear, an advantage for busy DJ.

The DJ series has been known to many as the "jack of all trades," with improved tracking, alongside of accurate sound reproduction. Featuring a low wear stylus design, the DJ provides excellent groove handling, even with less weight applied.

Output voltage at 1000Hz, 5cm/sec.
6 mV
Channel balance at 1kHz
2 dB
Channel separation at 1kHz
23 dB
Channel separation at 15 kHz
15 dB
Frequency range at -3dB
20-20.000 Hz
Frequency response
20-18.000 Hz 3dB/-2 dB
Tracking ability at 315 Hz at recommmende tracking force
80 μm
Compliance, dynamic lateral
9 μm/m N
Stylus type
Spherical
Stylus tip radius
R 18 μm
Tracking force range
2,0-4,0 g (20-40 mN)
Tracking force recommended
3,0 g (30 mN)
Tracking angle
20°
Internal impedance, DC resistance
750 Ohm
Internal inductance
450 mH
Recommended load resistance
47 kOhm
Recommended load capacitance
200-600 pF
Cartridge weight
18,5 g
Compatibility
DJ Series

Co-designed by DJ Q.Bert for scratch and back-cueing. High tracking ability. Ultra high output

Co-developed by one of the most legendary DJs of all time, the Ortofon Q.Bert provides unsurpassed handling, high output voltage, and low wear characteristics that literally put it in a class of its own.

Turntablists and mix DJs alike will appreciate the strong output of this cartridge, coupled with unrivaled tracking ability and sonic characteristics. The Q.Bert features a more subdued high end, which helps to minimize surface noise from worn vinyl, and an accentuated mid-range to help bring scratching to the front of the sound stage.

The Q-Bert has a supreme ability to trace the grooves of your records and it is tailored specifically for scratch. Due to its enomous output, it is perfect for scratch of all music with deep bass frequences.

Output voltage at 1000Hz, 5cm/sec.
11 mV
Channel balance at 1kHz
1,5 dB
Channel separation at 1kHz
22 dB
Channel separation at 15 kHz
•
Frequency range at -3dB
20-18.000 Hz
Frequency response
20-18.000 Hz -3 dB
Tracking ability at 315 Hz at recommmende tracking force
90 μm
Compliance, dynamic lateral
12 μm/m N
Stylus type
Spherical
Stylus tip radius
R 18 μm
Tracking force range
2,0-4,0 g (20-40 mN)
Tracking force recommended
3,0 g (30 mN)
Tracking angle
20°
Internal impedance, DC resistance
1.680 Ohm
Internal inductance
920 mH
Recommended load resistance
47 kOhm
Recommended load capacitance
200-400 pF
Cartridge weight
18,5 g

The UDG Sling Bag is a functional bag with a minimalist design. It's water-resistant, padded for maximum protection of your beloved vinyl goodies, and stores about 45 12" records as well as 24 CD copies in two folders.

UDG Sling Bag - features:

• 2 CD folders for 24 CD copies, each stored in the front compartment
• front and side pockets for accessories
• rugged top handle
• padded and PVC-backed walls
• adjustable and padded shoulder strap
• UDG security lock
• rubber details at bottom to protect the fabric
• dimensions: approx. 32 x 40 x 25 cm
• shell: 100% nylon
• lining: 100% polyester

Techno cartridge co-designed by DJs. Rubber tube especially developed for scratch and back-cueing. Very high output. Every professional ought to try the Electro, a techno cartridge made by a team of highly qualified technicians and experienced and capable DJs. Despite its sleek white styling, the Elektro isn't just another pretty face. Also featuring a reinforced rubber suspension, the Elektro is the perfect hybrid needle for the artist who both mixes and scratches. Enhanced tracking ability and excellent sound quality combine to form a unique balance of form and functionality. With bold, round sound, the Elektro brings your music to life, whether you're in the club or the studio. Unaffected by extreme sound pressure and repeated vibrations, it has a high output. The musical performance is always first-rate and the tracking ability of the spherical diamond stylus is quite good.

Ortofon Elektro Replacement Styles - Specs:

Output voltage at 1000Hz, 5cm/sec.
7.5 mV
Channel balance at 1kHz
1,5 dB
Channel separation at 1kHz
25 dB
Channel separation at 15 kHz
15 dB
Frequency range at -3dB
20-22.000 Hz
Frequency response
20-15.000 Hz 3dB/-2dB
Tracking ability at 315 Hz at recommmende tracking force
80 μm
Compliance, dynamic lateral
6 μm/m N
Stylus type
Spherical
Stylus tip radius
R 18 μm
Tracking force range
3,0-5,0 g (30-50 mN)
Tracking force recommended
4,0 g (40 mN)
Tracking angle
20°
Internal impedance, DC resistance
750 Ohm
Internal inductance
450 mH
Recommended load resistance
47 kOhm
Recommended load capacitance
200-600 pF
Cartridge weight
18,5 g

The world's first needle designed specifically for coded vinyl with low wear!

The DigiTrack is the perfect marriage of easy and function. You can now manupulate MP3's with the style and feel of a turntablist and the tradition of a turntable.

The DigiTrack responds to the generation of turntable DJs who make extensive use of timecoded vinyl applications, such as Serato (TM) and FinalScratch (TM). With DigiTrack's low wear design and tailored frequency response increase the lifespan of timecoded vinyl records, and provides high quality sound reproduction for playing conventional vinyl records as well.

DigiTrack also features excellent groove-handling capabilities for scratch and mix performance, as well as increased output voltage for improved TCV performance and better sound quality from your mixer's phono preamps.

High output and the best mix and scratch ability!

Output voltage at 1000Hz, 5cm/sec.
8 mV
Channel balance at 1kHz
1,5 dB
Channel separation at 1kHz
22 dB
Channel separation at 15 kHz
15 dB
Frequency range at -3dB
20-20.000 Hz
Frequency response
20-18.000 Hz +3 dB/-2 dB
Tracking ability at 315 Hz at recommmende tracking force
90 μm
Compliance, dynamic lateral
12 μm/m N
Stylus type
Spherical
Stylus tip radius
• -
Tracking force range
2,0-4,0 g (20-40 mN)
Tracking force recommended
3,0 g (30 mN)
Tracking angle
•
Internal impedance, DC resistance
•
Internal inductance
•
Recommended load resistance
•
Recommended load capacitance
•
Cartridge weight
18,5 g

Ausgangsspannung bei 1000Hz, 5cm/sec.
6 mV
Kanalbalance bei 1kHz
2 dB
Kanaltrennung bei 1kHz
23 dB
Kanaltrennung bei 15 kHz
15 dB
Frequenzbereich bei -3dB
20-22.000 Hz
Frequenzgang
20-20.000 Hz +/- 2 dB
Rillenfestigkeit bei 315 Hz mit empfohlener Auflagekraft
80 μm
Nadelnachgiebigkeit, dynamisch, seitlich
9 μm/m N
Nadeltyp
Special Elliptical
Durchmesser Nadelspitze
r/R 13/25 μm
Auflagekraftbereich
2,0-4,0 g (20-40 mN)
Auflagekraft empfohlen
3,0 g (30 mN)
Tracking Neigung
20°
Interne Impedanz, Gleichspannungswiderstand
750 Ohm
Interne Induktion
450 mH
Lastwiderstand empfohlen
47 kOhm
Belastungskapazität empfohlen
200-600 pF
Tonabnehmergewicht
18,5 g

The UDG Sling Bag Trolley Deluxe is equipped with the following features:

• stows approx. 60 12" vinyl records
• 2 CD folders (each one stows up to 24 CDs)
• rugged nylon upper
• front and side pockets with zip closure
• sturdy top handle
• adjustable, padded shoulder strap
• UDG security combination lock

• Weight 4,50 kg / 9.9 lbs
• Outer Dimensions cm: 40 x 45.5 x 31 | inch: 15.7 x 17.9 x 12.2
• Inner Dimensions cm: 31.5 x 32 x 20 | inch: 12.4 x 12.6 x 7.9
• Material Water Resistant Nylon 420D
• Protection Foam padded main compartment
• Extra's Retractable handle with 3 stage internal trolley system.
• Large front pocket + 2 side pocket for Accessories and smaller gears.
• Smooth rolling in-line wheels.
• Integrated combination lock.
• UDG Headphone Bag can buckled up.
• Fits 60 LP's or 1 CD Wallet 128 + 1 CD Wallet 280 or 1 CD Wallet + CD Player of MIDI Controller. Trolley fits up to 13" laptop.

Incorporating a new hidden trolley system, smooth rolling in-line wheels, electroplated zippers and integrated combination lock, the world's best selling 12" trolley bag has been reinforced and strengthened to provide you with even greater protection and durability. The Trolley Deluxe will hold approximately 60 Vinyl records and the SlingBag approximately 50 Vinyl records. However it also fits your MIDI Controller, Audio equipment, Headphone and cables.

• Weight: 8,50 kg / 18.7 lbs
• EAN: 8717228272776
• Color: Black, Orange inside
• Outer Dimensions (W x H x D): Trolley cm: 40 x 45.5 x 31 | inch: 15.7 x 17.9 x 12.2 - SlingBag cm: 39 x 38 x 21 | inch: 15.4 x 15 x 8.3
• Inner Dimensions (W x H x D): Trolley cm: 31.5 x 32 x 20 inch: 12.4 x 12.6 x 7.9 - SlingBag cm: 32 x 32 x 16 | inch: 12.6 x 12.6 x 6.3
• Material: Water Resistant Nylon 420D

Protection:
• Foam padded with PVC reinforced walls for extra protection
• Padded handgrip for comfortable carryng
• Electroplated zippers and integrated combination lock

Extra's:
• Includes SlingBag Trolley Deluxe + SlingBag
• Larger side & front pockets provides convenient storage for accessories & smaller gears
• Built in trolley system

Fits:
• 60 + 50 LP's
• or 2x Wallets 128 + 2x Wallets 280
• and/or 2 MIDI Controllers + misc. Accessories
• Trolley fits up to 13" laptop

With a solid body structure as well as in-line wheels and a two stage-trolley handle, the UDG Ultimate DIGI Trolley To Go the ideal bag for those long airport walkways. Built for the frequent flying DJ, with room for your valuable digital DJ gear or 50 vinyl LPs as well as 2 CD wallets, it has a large central compartment, a removable divider with an organizer section for your audio interface and headphones. A padded laptop sleeve to fit a 13" MacBook Pro is provided to protect your computer with two external pockets and a single internal mesh pocket providing storage for cables and documents. The UDG Digi Trolley To Go is the perfect long distance traveling partner.

UDG Trolley To Go - specifications:

• water-resistant nylon 420D
• padded main compartment holds up to 13" laptop plus MIDI controller (Vestax VCI-100) or 50 vinyl LPs or 2 CD wallets 128
• adjustable divider with organizer panel for audio interface and headphone
• 2 external accessory pockets plus single internal mesh pocket
• retractable handle with 2-stage trolley system
• ergonomic detachable shoulder strap
• integrated combination lock
• outer dimensions: 36 x 44 x 26 cm (14.2 x 17.3 x 10.2 inch)
• inner dimensions: 33 x 33 x 16 cm (13 x 13 x 6.3 inch)
• weight: 5.16 kg (11.35 lbs)

The UDG Digi BackPack was specially designed to cater for the laptop-based generation DJ affording them maximum functionality with performance orientated style. A cleverly designed side entry compartment for a laptop up to 15.4 inch allows access without having to rummage through the main body of the bag. The spacious main compartment can hold an extra laptop or used for magazines/paperwork whilst in transit.
The front compartment features a detachable interface pouch and accessories organizer pocket. There are also 5 additional exterior pockets that provide storage for personal items, one of these has an ear bud access point with a hinged storage pocket so that you can listen to your mp3 player whilst on the go.

UDG Digi BackPack - specifications:

• water resistant nylon 450D shell
• easy access size entry padded compartment for 15.4 inch laptop with vertical file organization
• main compartment for laptop, LPs, books or magazine
• front compartment with organization panel and detachable pouch for audio interface
• 5 exterior pockets for personal essentials, including one with ear bud pass-through for mp3 players and unique hinged headphone pocket
• S-curved shoulder straps for ultimate comfort
• outer dimensions: approx. 33.5 x 48 x 27 cm (13.2 x 18.9 x 10.6 inch)
• inner dimensions: approx. 30 x 42 x 13 cm (11.8 x 16.5 x 5.1 inch)
• weight: 1.8 kg (4 lbs)

Inspired by the legendary UDG Producer Bag, the UDG Ultimate Producer Bag Large has been created to cater for those electronic musicians who crave more space for their performance equipment.

The UDG Producer Bag Large offers increased space for performers using laptops up to 18.4 inch and larger MIDI controllers.

Constructed from high quality fabrics, the backpack style UDG Producer Bag Large features padded walls with an adjustable divider so that you can create an internal partition to suit your own requirements. Available in black, the bag offers both comfortable transportation and padded protection for your valuable items.

UDG Producer Bag Large - specifications:

Weight 3,25 kg / 7.15 lbs
EAN 8717228276675
Color Black, Orange inside
Outer Dimensions (W x H x D) cm: 46 x 56 x 25 | inch: 18.1 x 22 x 9.8
Inner Dimensions (W x H x D) cm: 32 x 46.5 x 15 | inch: 12.6 x 18.3 x 5.9
Material Water Resistant Nylon 420D
Protection Padded MIDI Controller compartment
Bottom guards fabrics protect from scuffing and abration.
Extra's 6 pockets for Accessories and smaller gears
Top carry handles
Ergonomic detachable shoulder strap
Integrated combination lock.
Fits Up to 18.4" laptop,
Pioneer Toraiz SP-16, DJS-1000, DJM-750MK2,
NI Traktor Kontrol S2 MK2, Maschine Jam/ MK3/ MK2, Traktor Z2,
Denon DJ Prime Go, MC6000 MK2, MC3000,
Numark iDJ Live II, Mixtrack II / Pro II,
Rane Seventy, Seventy-Two,
Akai MPC Live II, APC 40 MK2, MPD232, MPD26, MPD32,
Reloop Elite, Beatpad/2, Beatmix, Digital Jockey-3, Jockey 3 Remix, Terminal Mix 2,
Novation AFX, 25SL MK2, Launchkey 25, Nocturn 25,
Hercules DJConsole RMX2, DJControl Jogvision, DJ Control Air+ S,
M-Audio Oxygen 25, Trigger Finger Pro, Xponent,
Stanton SCS.4DJ, DJC.4,
Livid OHM 64,
Vestax VCI-380/400/400DJ,
Arturia Drumbrute, Keylab 25,
various pedalboards,

A REBORN CLASSIC.
The PLX-1000 is precision engineered for the booth, drawing on 50 years’ experience of making high-end turntables. This high-torque direct drive turntable is equipped with a classic layout and a rubber-lined, S-shaped tone arm that improves isolation and prevents feedback. It is solidly built for excellent vibration damping and ultra-precise, high grade audio playback.

Featuring next generation improvements, the PLX-1000 is the perfect score for professional DJs and vinyl enthusiasts. Combine this turntable with your Pioneer DJM mixer and get the ideal DJ system set-up.

TURN THE TABLES
The high-torque direct drive makes sure that your tracks reach a rotation speed of 33⅓ rpm in merely 0.3 seconds thanks to a starting torque of 4.5kg/cm (or more). Plus it ensures stable rotation and exceptional control.

PICK UP THE PACE
Unique to this turntable is the multi-pitch tempo control. Next to a standard variable width of ±8%, you can also select a variable width from ±16% and ±50%. A simple reset button instantly reverts to the fixed rotation speed at ±0%.

EASILY CONNECTED
For low impendance and amazing sound quality output, you can easily connect to the professional-grade, gold-plated RCA jacks. Ideal for a DJ on the road, the PLX-1000 has interchangeble power and audio cables.

ncluded Accessories
Turntable sheet
Slip mat and sheet
Dust cover
Head shell
Balance, sub and shell weights
Audio cable
Ground wire

Width
453 mm
Height
159 mm
Depth
353 mm
Weight
13.1 kg
Power Requirements
220-240 V / 50/60 Hz

Drive Method
Quartz lock, servo-type, direct drive
Platter
Aluminium, die-casting diameter: 332 mm
Motor
3-phase, brushless DC motor
Braking System
Electronic brake
Rotation Speed
33⅓-45 rpm
Rotation Adjustment Range
±8, ±16, ±50 %
Wow and Flutter
<0.01% (Measured by obtaining signal from built-in frequency generator of motor assembly.)
Signal-to-Noise Ratio
70 dB
Starting Torque
> 4.5 kg/cm
Start Time
0.3 sec (at 33⅓ rpm)

Arm Type
Universal type S-shape tone arm
Gimbal-supported type bearing structure
Static balance type
Overhang
15 mm
Effective Length
230 mm
Tracking Error
Within 3°
Height Adjustment Range
6 mm
Stylus Pressure Variable Range
0-4 g (1 scale 0.1 g)
Single Cartridge Weight
3.5-13 g

M6 enables you to step up to a four-channel mixer. This club-style design not only works with any standard audio sources including turntables and CD players, but it also has a USB computer connection. When connected to your Mac or PC, the plug-and-play connection empowers you to mix in audio in from music-player software and record your sets into virtually any audio recording application.

You will enjoy a complete range of performance essentials in M6, including three-band EQ and LED metering per channel. M6 has a replaceable crossfader with slope control, and you can assign any channel to either side of the crossfader.

You can talk over the mix with M6’s dedicated XLR microphone channel and a secondary mic input on channel four. And for the best possible sound, M6 has balanced outputs.

Get all the flexibility of a four-channel mixer plus the power of computer connection with M6.

FEATURES

Four input channels, each with gain, three-band EQ, and LED metering
USB computer connection for playing and recording with Mac or PC
Play music from music-player software
Record your mix to your computer
Multiple phono, line, and mic inputs
Dedicated XLR mic channel and additional mic input on channel 4
Replaceable crossfader with slope control
Assign any channel to either side of the crossfader
Class Compliant: this product is immediately compatible with every current and future version of Mac OS X and iOS and with Windows (98SE and up) operating systems.
INCLUDES

M6 USB Mixer
Power Cable
Quickstart Guide

Weight: 9.6 lbs
Dimensions (WxDxH): 12.625" x 14.25" x 4"

Get up and running quickly at any gig.

READY FOR DIGITAL OR ANALOG

DJs always need a dependable mixer. M101USB fits the bill perfectly as a highly adaptable two-channel mixer for virtually any DJ. M101USB lets you get up and running quickly whether you’re using a computer, turntables or CDs. M101USB is right at home at weddings, parties, clubs and everything in-between.

MIX YOUR MUSIC YOUR WAY

Beginners and seasoned DJs alike who want a durable USB-equipped two-channel solution will find M101USB a perfect fit. M101USB builds on the two-channel M101 mixer with the addition of an easy-to-use USB audio interface for DJs who want the option of working with their computer as well as traditional analog I/O.


TWEAKABLE TUNES

Beyond simply mixing, M101USB has a built-in EQ so that you can fine tune your mix depending on the room or the tracks themselves. Two pairs of switchable Phono/Line inputs are included along with a crossfader, ¼” mic input and stereo RCA line output for connection to an amplifier, powered speakers or another mixer. M101USB can be rack-mounted and features Numark’s legendary industrial-grade durability.

GET CONNECTED

Connecting M101USB to your computer is a snap using a single USB cable. Once connected you can use your computer as an audio source or record your sets straight to your computer's hard drive. If you're a computer DJ on the move and need solid, dependable two-channel performance, look no further than the M101USB mixer.

FEATURES

Two-channel rack-mountable mixer with USB
USB audio built in for playing from or recording to your computer
Two pairs of Phono/Line inputs
Built-in 2-band EQ for quick, easy sound tweaks
1/4-inch Mic input for voiceovers and announcements
Stereo Output for easy connection to amps, powered speakers or another mixer
Class Compliant: this product is immediately compatible with every current and future version of Mac OS X and iOS and with Windows (98SE and up) operating systems.
INCLUDES

M101USB Mixer
Power Supply
Quickstart Guide

Manual: http://www.numark.com/images/product_downloads/m101usb___quickstart_guide___v1.0.pdf

M2 is a two-channel DJ scratch mixer with all the essentials to hit the stage in Numark style.

FEATURES

Inputs: two phono/line switchable (RCA), two line (RCA), mic (1/4")
Outputs: Master (RCA), Record (RCA), Headphone (1/4" stereo)
Three-band EQ and gain on each channel
EQ and gain on mic channel
Replaceable crossfader with reverse and slope-controls
Crossfader-style cueing

Switchable phono/line inputs for turntables, CD players, and other line sources make M2 a superb choice for any DJ setting from weddings to clubs, parties to practice setups. A mic input with dedicated EQ and gain, and a headphone output with crossfader-style cueing complete the plentifully featured package.

Three-band EQ on each channel plus crossfader-reverse and slope controls give you all the tools you need to drive your audience from behind the wheels of steel. M2 is the perfect mixer for any scratch DJ.

Product Dimensions: 11.4" x 9.5" x 3.6"

Manual: http://www.numark.com/images/product_downloads/m2_quickstart_guide_v1_0.pdf

This is the most critically acclaimed model in the M-Series line, praised by top audio engineers and pro audio reviewers year after year. The ATH-M50x features the same coveted sonic signature, now with refined earpads and detachable cables. From large-aperture drivers to sound isolating earcups and robust construction, the M50x provides an unmatched experience for the most critical audio professionals.

Features:
• Critically acclaimed sonic performance praised by top audio engineers and pro audio reviewers
• Proprietary 45 mm large-aperture drivers with rare earth magnets and copper-clad aluminum wire voice coils
• Exceptional clarity throughout an extended frequency range, with deep, accurate bass response
• Circumaural design contours around the ears for excellent sound isolation in loud environments
• 90° swiveling earcups for easy, one-ear monitoring
• Professional-grade earpad and headband material delivers more durability and comfort
• Detachable cable (3 cables included)

Specifications:
• Type: Closed-back dynamic
• Driver Diameter: 45 mm
• Magnet: Neodymium
• Voice Coil: CCAW (Copper-clad aluminum wire)
• Frequency Response: 15 - 28,000 Hz
• Max Input Power: 1,600 mW @ 1KHz
• Sensitivity: 99 dB
• Impedance: 38 ohms
• Folding/collapsible: Yes
• Weight: 10 oz (284 g) without cable/connector
• Cable - Detachable: Yes
• Cable Includes: 1.2m-3m coiled, 3m straight, 1.2m straight cables
• Connector: Gold-plated stereo 1/8” (3.5 mm) connector with strain relief
• Accessories included: Screw-on 1/4” adapter, pouch

The high-performance ATH-M40x professional headphones are tuned flat for incredibly accurate audio monitoring across an extended frequency range. Your studio experience is enhanced with superior sound isolation and swiveling earcups for convenient one-ear monitoring. Engineered with pro-grade materials and robust construction, the M40x excels in professional studio tracking and mixing, as well as DJ monitoring.

Cutting-edge engineering and robust construction
40 mm drivers with rare earth magnets and copper-clad aluminum wire voice coils
Tuned flat for incredibly accurate sound monitoring across the entire frequency range
Circumaural design contours around the ears for excellent sound isolation in loud environments
90° swiveling earcups for easy, one-ear monitoring
Professional-grade earpad and headband material delivers more durability and comfort
Detachable cable (2 cables included)

Type: Closed-back dynamic
Driver Diameter: 40 mm
Magnet: Neodymium
Voice Coil: CCAW (Copper-clad aluminum wire)
Frequency Response: 15 - 24,000 Hz
Max Input Power: 1,600 mW @ 1KHz
Sensitivity: 96 dB
Impedance: 35 ohms
Folding/collapsible: Yes
Weight: (Without cable) 8.5 oz (240 g)
Cable - Detachable: Yes
Cable Includes: 1.2m-3m coiled, 3m straight cablesConnector Gold-plated stereo 1/8” (3.5 mm) connector with strain relief
Accessories included: Screw-on 1/4” adapter, pouch

With enhanced audio clarity and sound isolation, the ATH-M30x professional monitor headphones are tuned for highly detailed audio. Featuring strong mid-range definition, these versatile monitoring headphones are ideal in a variety of situations. Designed primarily for studio tracking and mixing, they offer added features for increased portability, making them a great choice for field recording.

Advanced build quality and engineering
40 mm drivers with rare earth magnets and copper-clad aluminum wire voice coils
Tuned for enhanced detail, with excellent mid-range definition
Circumaural design contours around the ears for excellent sound isolation in loud environments

Type: Closed-back dynamic
Driver Diameter: 40 mm
Magnet: Neodymium
Voice Coil: CCAW (Copper-clad aluminum wire)
Frequency Response: 15 - 22,000 Hz
Max Input Power: 1,300 mW @ 1KHz
Sensitivity: 96 dB
Impedance: 47 ohms
Folding/collapsible: Yes
Weight: (Without cable) 7.8 oz (220 g)
Cable - Detachable: No
Cable: 3 m (9.84’) Straight cable, left-side exit
Connector: Gold-plated stereo 1/8” (3.5 mm) connector with strain relief
Accessories included: Screw-on 1/4” adapter, pouch

The ATH-M20x professional monitor headphones are a great introduction to the critically acclaimed M-Series line. Modern design and high-quality materials combine to deliver a comfortable listening experience, with enhanced audio and effective isolation. An excellent choice for tracking and mixing.

Advanced build quality and engineering
40 mm drivers with rare earth magnets and copper-clad aluminum wire voice coils
Tuned for enhanced low-frequency performance
Circumaural design contours around the ears for excellent sound isolation in loud environments
Convenient single-side cable exit

Type: Closed-back dynamic
Driver Diameter: 40 mm
Magnet: Neodymium
Voice Coil: Copper-clad aluminum wire
Frequency Response: 15 - 20,000 Hz
Maximum Input Power: 700 mW at 1 kHz
Sensitivity: 96 dB
Impedance: 47 ohms
Weight: 190 g (6.7 oz), without cable and connector
Cable: 3.0 m (9.8'), straight, left-side exit
Accessory Included: 6.3 mm (1/4") snap-on adapter

760 g layer weight to stabilize vinyl records.
Ø 70mm

760 g layer weight to stabilize vinyl records.
Ø 70mm

SME construction, high-quality cherrywood edition for superior cushioning; audiophile cables with gold-plated ports; weight: 10g.

Ortofon Stylus 10 - technical data:

• Frequency range 20-24.000 Hz
• Frequency response 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force *) 70 µm
• Compliance, dynamic, lateral 25 µm/mN
• Stylus type Elliptical
• Stylus tip radius r/R 8/18 µm
• Tracking force range 1.25-1.75 g (12.5-17.5 mN)
• Tracking force, recommended 1.5 g (15 mN)
• Tracking angle 20°
• Stylus color Black
• Recommended for following cartridges: Super OM 10, OM 10, OMP-mount 10, OMBulk 10, OMT 10, LM 10, Concorde 10, Concorde EC 10, TM 10H, LMB 12, SMB 12, LMA 12, Concorde STD, Dual ULM 65E, Dual ULM 66E

The AIAIAI TMA-2 Cable C02 is a coiled cable with adaptor (SKU 01302). 4 mm/1.5 m.

AIAIAI proudly presents their new headphone project. With TMA-2 Modular, AIAIAI has created the next step for the 21st century headphone: a framework consisting of modular audio technology, which provides a vast range of options across sound, function, comfort, and design, resulting in a unique, personalized headphone. To AIAIAI, Modular means a framework of elements that can be connected or combined in different ways. TMA-2 Modular means opportunity; a segmental build solution based on the TMA-1 series that lets you decide on your headphone preferences while enabling quick and easy change or upgrade of parts along the way.

The Modularity will consist of 4 basic elements, which all shape the final performance of the headphone:

• headbands - choose between 3 different shapes and cushion types
• speaker units - choose between 4 different sound settings/drivers
• earpads - choose between 5 different cushion types and materials
• cables - choose between 6 cables w/wo microphone, material, length etc.

Important info: the sound configuration is determined by the speaker unit and the earpads, the combination of which have equal importance in shaping the overall sound of the headphone. A central part of the modular concept is that users are able to get a product more specifically suitable for their preferences and usage.

Technical data
Frequency range
20-25.000 Hz
Frequency response
20-25.000 Hz
Tracking ability at 315Hz at recommended tracking force *) 65 µm
Compliance, dynamic, lateral 20 µm/mN
Stylus type Elliptical
Stylus tip radius r/R 8/18 µm
Equivalent stylus tip mass 0,5 mg
Tracking force range 1,5-2,0 g (15-20 mN)
Tracking force, recommended 1,75 g (17,5 mN)
Tracking angle 20°
Stylus colour Black
Recommended for following cartridges OM 5E, OMP 5E, OMB 5E, OMT 5E

Technical data:
• Frequency range 20-22.000 Hz
• Frequency response 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force *) 70 µm
• Compliance, dynamic, lateral 20 µm/mN
• Stylus type Elliptical
• Stylus tip radius r/R 8/18 µm
• Equivalent stylus tip mass 0,5 mg
• Tracking force range 1,6-2,0 g (16-20 mN)
• Tracking force, recommended 1,8 g (18 mN)
• Tracking angle 20°
• Stylus colour Red
• Recommended for following cartridges 2M Red / 2M Red Verso(Interchangeable with 2M Blue / 2M Blue Verso)

The AIAIAI TMA-2 Headband H03 is made from H03 nylon (SKU 01203) and equipped with synthetic leather padding for high comfort.

AIAIAI proudly presents their new headphone project. With TMA-2 Modular, AIAIAI has created the next step for the 21st century headphone: a framework consisting of modular audio technology, which provides a vast range of options across sound, function, comfort, and design, resulting in a unique, personalized headphone. To AIAIAI, Modular means a framework of elements that can be connected or combined in different ways. TMA-2 Modular means opportunity; a segmental build solution based on the TMA-1 series that lets you decide on your headphone preferences while enabling quick and easy change or upgrade of parts along the way.

The Modularity will consist of 4 basic elements, which all shape the final performance of the headphone:

• headbands - choose between 3 different shapes and cushion types
• speaker units - choose between 4 different sound settings/drivers
• earpads - choose between 5 different cushion types and materials
• cables - choose between 6 cables w/wo microphone, material, length etc.

Important info: the sound configuration is determined by the speaker unit and the earpads, the combination of which have equal importance in shaping the overall sound of the headphone. A central part of the modular concept is that users are able to get a product more specifically suitable for their preferences and usage.

rhythm – drum synthesizer and sequencer with parameter locks, individual step re-trig and punch-in effects.

real synthesised drum sounds
sampled drum sounds
16 punch-in effects including delay, bit crusher and filters.
parameter locks
auto compressor
hardware limiter
step multiplier
fill-ins
16-step sequencer
16 patterns
16 pattern chaining
clock
alarm clock
jam sync with audio through
3.5 mm audio out / in
animated unique lcd display
folding stand
2 year standby time

Manual: https://www.teenageengineering.com/guides/po-16/en

sub – bass line synthesizer and sequencer with parameter locks, punch-in effects and play styles.

multiple real synthesizer engines, including fm, subtractive synthesis, wave table and physical modeled string.
16 punch-in effects including delay, bit crusher and filters.
16 punch-in bass oriented play styles
parameter locks
auto compressor
hardware limiter
16-step sequencer
16 patterns
16 pattern chaining
clock
alarm clock
jam sync with audio through
3.5 mm audio out / in
animated unique lcd display
folding stand
2 year standby time

Manual: https://www.teenageengineering.com/guides/po-12/en

factory – melody synthesizer and sequencer with parameter locks, punch-in effects, arpeggio and chord play styles.

multiple real synthesizer engines, including fm, subtractive synthesis, wave table and physical modeled string.
16 punch-in effects including delay, bit crusher and filters.
16 punch-in arpeggio and chord play styles
parameter locks.
auto compressor
hardware limiter
16-step sequencer
16 patterns
16 pattern chaining
clock
alarm clock
jam sync with audio through
3.5 mm audio out / in
animated unique lcd display
folding stand
2 year standby time

Manual: https://www.teenageengineering.com/guides/po-14/en

How to minimize the risk of ring wear of your gateold covers? Just put your vinyl goodies respectively the record sleeves in these transparent outer sleeves to keep your collection in good shape.

Record Outer Sleeve 12" Vinyl Doppel LP Gatefold Schutzhüllen - specific details:

• dimensions: 316 x 640 x 0.1 mm
• material: translucent CPP
• selling unit: 50 pieces

MM Phono Pre-amplifier

Good sound from sound technology
• Metal case shields the electronics from vibrational and electromagnetic interference
• Special low-noise ICs used
• Optimal channel separation through dual-mono circuitry
• Gold plated RCA connection sockets
• DC power supply (< 1 watt standby power)

Features
• Amplification and RIAA equalisation for MM cartridges
• Small size allows installation close to record player

107x36x104 (115)mm

Manual: http://www.project-audio.com/inhalt/en/manual/manual_phonoboxmm.pdf

Turntable platter

Functional and easy to use sound improvement!

Upgrade your Elemental or Essential turntable with Acryl it E. Acryl it E is made from acrylic with satinised surface and brings a more liquid sound that leaves no space for platter resonances.

The change is easily made: just exchange your metal platter for Acryl it E. Acryl it E is able to improve overall performance significantly!

Features:
• Suitable for Elemental, Essential & Primary turntables
• Substitutes MDF platter
• Inert material avoids resonances
• Ideal for use with Clamp it
• Audiophile sound tuning
• Optical upvaluation

Technical Specifications:
• Material: Acryl satiniert
• Diameter: 300 mm
• Height: 20 mm
• Weight: 1,2 kg net

The 2M Series of cartridges is designed for precise and accurate retrieval of the information in the record groove. Our philosophy is to play the record sound as accurate as possible, without coloring the sound

The name 2M was selected from several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.
The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.
We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

The 2M Blue Series features:

an improved engine, which provides an increased output of 5.5mV
Nude Elliptical diamond and split pole pins with a copper wire

Technical data:
• Frequency range 20-25.000 Hz
• Frequency response 20-20.000 Hz + 2 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force *) 80 µm
• Compliance, dynamic, lateral 20 µm/mN
• Stylus type Nude Elliptical
• Stylus tip radius r/R 8/18 µm
• Equivalent stylus tip mass 0,5 mg
• Tracking force range 1,6-2,0 g (16-20 mN)
• Tracking force, recommended 1,8 g (18 mN)
• Tracking angle 20°
• Stylus colour Blue

Total Mixing Performance in a Small Package
MIDImix is a portable compact high-performance mixer that has the unique ability to control your Digital Audio Workstation (DAW) with the press of a single button, giving all musicians and producers complete, uncomplicated mastery over mixing and processing of their digital music creations on the go.

Until now, you had to build and layer your mixes at the performance site first, then transfer that mix at a later time to your DAW for post-mix processing and manipulation. What a pain. This is not the way you’d like to do it, because of the time lag between constructing the initial mix and then not being able to work on it until later in your DAW. This meant you only had a limited ability to create the exact mix you wanted in real time.

The On-Site Mixing Problem Solved!
Akai Professional’s portable MIDImix solves this problem completely. With Akai Professional’s famous build quality and cutting-edge engineering, it combines a high-performance mixer with 8 individual line faders and a master fader, 24 control knobs arranged 3 per channel and 1 to 1 mapping with Ableton Live (Ableton Live Lite is included). You can send all the mixer’s settings to their DAW with a single press of a button, for unprecedented management and precise control over your DAW’s functionality. This is great—it means that you can mix and modify/manipulate your projects concurrently in real time, giving you a much wider array of creative options as a result of the far greater creative flexibility afforded by MIDImix.

Nothing Else Like it
Up until now, there was just no solution for musicians and producers who needed a compact, easily portable way to mix and process their projects on site. But MIDImix is the best solution for portable mixing on the go. MIDImix offers an intuitive, familiar mixer layout, solid connectivity with the most popular DAWs, and legendary Akai Professional quality. MIDImix is exactly what you need to do great mixes and professional processing on site—at the same time.

Midi mixer to control virtually any DAW
8 individual line faders, 1 master fader
24 knobs, arranged 3 per channel
16 buttons arranged in 2 banks provide mute, solo and record arm functionality per channel
Sends all mixer settings to the DAW with a single button press
1 to 1 mapping with Ableton Live (Ableton Live Lite included)

Requirements:
Macintosh: 1.25 GHz G4/G5 or faster (Intel Mac recommended); 1GB RAM (2GB recommended); Mac OS X 10.4.11 (10.5 or later recommended)
PC: 1.5 GHz Pentium 4 Celeron-compatible CPU or faster (multicore CPU recommended); 1 GB RAM (2GB recommended); Windows 8, Windows 7, Windows Vista, or Windows XP; Windows-compatible sound card (ASIO driver support recommended); QuickTime recommended
Available USB port

Manual: http://6be54c364949b623a3c0-4409a68c214f3a9eeca8d0265e9266c0.r0.cf2.rackcdn.com/1415/documents/MIDImix-UserGuide-v1.0.pdf

The UDG DIGI Headphone Bag is a premium headphone carrying bag made from Ballistic Nylon that is designed to protect headphone, USB drives, SD cards, Ext. hard-drive, mobile phone, cables, business cards, credit cards and accessories in one padded carry bag that includes a handgrip, detachable and adjustable shoulder strap. The UDG DIGI Headphone Bag the one bag a DJ need to carry around today’s digital media

Outer Dimensions cm: 22 x 22 x 9 | inch: 8.7 x 8.7 x 3.5

Inner Dimensions cm: 21 x 21 x 8 | inch: 8.3 x 8.3 x 3.1

Material Water resistant Ballistic Nylon 1680D

Protection Foam padded interior

Extra's Detachable and adjustable shoulder strap. Holds USB drives, SD cards, hard drive, mobile phone, cables, business cards, credit cards and accessories

Fits Most foldable DJ Headphones.

plastic vacuum tube 10 inch

The 2M Series is developed in conjunction with the Danish Industrial designer Møller Jensen Design – the same designer who designed the award winning MC Jubilee and Kontrapunkt series. Inspired by the facets of a diamond, whose contours gracefully trace the grooves on a record’s surface, the 2M’s handsome elegance establishes a great combination of form and functionality.

The name 2M was selected from among several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.

Of course the 2M isn’t just another pretty face. It has been engineered to the highest standards and is congruent with Ortofon’s unrelenting commitment to providing the most precise and accurate reproduction possible without coloration.

The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Blue features:

• an improved engine, which provides an increased output of 5.5mV and an optimized sound reproduction and a high level of sonic accuracy

• Nude Elliptical diamond and split pole pins with a copper wire

• The cartridge body is manufactured from Hopelex, an environment-friendly material which ensures high rigidity while eliminating unwanted resonances

2M Blue adds more dynamics and resolution, sounds more open and reproduces more details than 2M Red

Output voltage at 1000 Hz, 5cm/sec. - 5,5 mV
Channel balance at 1 kHz - 1,5 dB
Channel separation at 1 kHz - 25 dB
Channel separation at 15 kHz - 15 dB
Frequency range at - 3dB - 20-25.000 Hz
Frequency response - 20-20.000 Hz + 2 / - 1 dB
Tracking ability at 315Hz at recommended tracking force - 80 µm
Compliance, dynamic, lateral - 20 µm/mN
Stylus type - Nude Elliptical
Stylus tip radius - r/R 8/18 µm
Tracking force range - 1,6-2,0g (16-20 mN)
Tracking force, recommended - 1,8 g (18 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1,3 kOhm
Internal inductance - 700 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 150-300 pF
Cartridge colour, body/stylus - Black/Blue
Cartridge weight - 7,2 g
Replacement stylus unit - 2M Blue (interchangeable with 2M Red and 2M Silver)

Each of the 2M Series cartridges has its own individual sonic expression, and all five models together represent the ensemble of five classic variations:

• 2M Mono SE, 2M Mono and 2M 78 are a true mono cartridges for playing mono vinyl records
• 2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth
• 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details
• 2M Bronze adds even more details and resolution but in a very evenhanded way that pays respect to all elements
• 2M Black is the best of everything, true to the groove with resolution and accurate insight into each recording

One size fits all! The new MULTI-FORMAT TURNTABLE CASE is a heavy-duty road case that was especially designed to fit the popular Technics SL-1200/1210 Turntable. It includes several foam pads to accommodate various new models such as a Pioneer PLX-1000 and other models from Stanton, Vestax, Reloop, American Audio, Numark etc.

Fits Technics 1200/1210 MK2 /MK5, Pioneer PLX-1000, Reloop RP-8000/7000/6000/2000, Stanton ST-150, Vestax PDX 3000, Numark TTX, Audio Technica LP120-USB/LP1240-USB, American Audio Power Drive 2.2 etc.

Incl. adjustment foams to accommodate various turntable models

Heavy duty construction of 9 mm vinyl laminated plywood

Solid aluminum profiles and spring loaded butterfly locks

Secure stacking due to stackable ball corners

Outer dimensions: (B/H/T): 43 x 52 x 22 cm /internal: (B/H/T): 36,5 x 45,5 x 7,5 cm

Due to their low weight and the option of one-ear listening, the HD 25 headphones are indispensable for mobile monitoring. The closed-back HD 25 are purpose-designed, professional monitoring headphones offering high attenuation of background noise.

Capable of handling very high sound pressure levels and of extremely robust construction, these headphones perform exceptionally well in loud environments, e.g. ENG, sound reinforcement, studio monitoring and audio equipment testing. Ideal monitoring headphones for cameramen and DJs, these are a pair of true sound professionals’ working headphones.

FEATURES

High sensitivity due to lightweight aluminium voice coils

Capable of handling very high sound pressure levels

Very lightweight and comfortable, even if used for long periods of time

Tough, detachable, single-sided cable

Rotatable capsule for single-ear listening

WHAT'S IN THE BOX?

1 HD 25
1 Screw on jack adapter 3.5 to 6.3 mm

Due to their low weight and the option of one-ear listening, the HD 25 headphones are indispensable for mobile monitoring. The closed-back HD 25 are purpose-designed, professional monitoring headphones offering high attenuation of background noise.

Capable of handling very high sound pressure levels and of extremely robust construction, these headphones perform exceptionally well in loud environments, e.g. ENG, sound reinforcement, studio monitoring and audio equipment testing. Ideal monitoring headphones for cameramen and DJs, these are a pair of true sound professionals’ working headphones.

FEATURES

High sensitivity due to lightweight aluminium voice coils

Capable of handling very high sound pressure levels

Very lightweight and comfortable, even if used for long periods of time

Tough, detachable, single-sided cable

Rotatable capsule for single-ear listening

WHAT'S IN THE BOX?

1 HD 25
1 Screw on jack adapter 3.5 to 6.3 mm
HD 25 Plus only: 1 Pouch
HD 25 Plus only: 1 additional pair of soft earpads
HD 25 Plus only: 1 additional 1.5m straight cable

SpiralKabel 3m, für alle HD-25

The PLX-500 inherits the layout of the PLX-1000 professional turntable and produces a warm, clear analogue sound. The perfect deck if you want to start playing with vinyl or if you just want to listen to your record collection at home.

Solidly built with excellent vibration damping and precise audio playback, this high-torque deck has a USB out so you can make digital recordings of your vinyl collection in our free rekordbox software. You can also combine the PLX-500 with the rekordbox dvs Plus Pack, a compatible mixer and the RB-VS1-K Control Vinyl to play and scratch with digital files.

EXCELLENT SOUND DESIGN

Just like the PLX-1000, the PLX-500 is built to produce a high-quality vinyl sound. The shortest possible audio routing from the stylus to the outputs reduces distortion, while the phone/line output switch lets you connect directly to your sound system or to powered speakers with no need for an external amplifier.

EASY DIGITAL RECORDING

Record your vinyl collection to high-quality digital files by simply connecting the turntable to your PC or Mac via the USB out.

SMOOTH DJ PLAY

Use the PLX-500 to mix and scratch your vinyl records or combine the turntable with rekordbox dvs, a compatible DJ mixer and the RB-VS1-K Control Vinyl to play and perform with your digital files.

COVER ART DISPLAY

Put your record covers on display while listening to your vinyl thanks to the sleeve stand inside the dust cover.

Included Accessories:
• PLX-500
• Power cord
• USB cable
• Slip mat
• Dust cover
• Adapter for EP records
• Head shell (with cartridge)
• Balance and shell weights
• Audio adaptor cable: 1 Stereo pin plug (female) & 1 Stereo mini plug (male)
• Operating instructions

Specifications:
• Width: 17.72 in
• Height: 6.26 in
• Depth: 14.49 in
• Weight: 23.59 lb

Turntables:
• Drive Method: Servo-type direct drive
• Platter: Aluminium, die-casting diameter: 332 mm
• Motor: 3-phase, brushless DC motor
• Braking System: Electronic brake
• Rotation Speed: 33⅓, 45, 78 rpm
• Rotation Adjustment: Range ±8 %
• Wow and Flutter: < 0.15% WRMS
• Signal-to-Noise Ratio: 50 dB
• Starting Torque: > 1.6 kgf cm
• Start Time: Within 1 sec (at 33⅓ rpm)

Tone Arm:
• Arm Type: Universal type S-shape tone arm, Gimbal-supported type bearing structure, Static balance type
• Overhang: 0.63 in
• Effective Length: 9.07 in
• Tracking Error: Within 3°
• Height Adjustment Range: 0.24 in
• Stylus Pressure Variable Range: 0-4 g (1 scale 0.1 g)
• Cartridge Weight Single: < 9.5 g
• Cartridge type: VM

Terminals:
• Outputs: 1 PHONO/LINE (RCA)
• USB: 1 USB B port

The PLX-500 inherits the layout of the PLX-1000 professional turntable and produces a warm, clear analogue sound. The perfect deck if you want to start playing with vinyl or if you just want to listen to your record collection at home.

Solidly built with excellent vibration damping and precise audio playback, this high-torque deck has a USB out so you can make digital recordings of your vinyl collection in our free rekordbox software. You can also combine the PLX-500 with the rekordbox dvs Plus Pack, a compatible mixer and the RB-VS1-K Control Vinyl to play and scratch with digital files.

EXCELLENT SOUND DESIGN

Just like the PLX-1000, the PLX-500 is built to produce a high-quality vinyl sound. The shortest possible audio routing from the stylus to the outputs reduces distortion, while the phone/line output switch lets you connect directly to your sound system or to powered speakers with no need for an external amplifier.

EASY DIGITAL RECORDING

Record your vinyl collection to high-quality digital files by simply connecting the turntable to your PC or Mac via the USB out.

SMOOTH DJ PLAY

Use the PLX-500 to mix and scratch your vinyl records or combine the turntable with rekordbox dvs, a compatible DJ mixer and the RB-VS1-K Control Vinyl to play and perform with your digital files.

COVER ART DISPLAY

Put your record covers on display while listening to your vinyl thanks to the sleeve stand inside the dust cover.

Included Accessories:
• PLX-500
• Power cord
• USB cable
• Slip mat
• Dust cover
• Adapter for EP records
• Head shell (with cartridge)
• Balance and shell weights
• Audio adaptor cable: 1 Stereo pin plug (female) & 1 Stereo mini plug (male)
• Operating instructions

Specifications:
• Width: 17.72 in
• Height: 6.26 in
• Depth: 14.49 in
• Weight: 23.59 lb

Turntables:
• Drive Method: Servo-type direct drive
• Platter: Aluminium, die-casting diameter: 332 mm
• Motor: 3-phase, brushless DC motor
• Braking System: Electronic brake
• Rotation Speed: 33⅓, 45, 78 rpm
• Rotation Adjustment: Range ±8 %
• Wow and Flutter: < 0.15% WRMS
• Signal-to-Noise Ratio: 50 dB
• Starting Torque: > 1.6 kgf cm
• Start Time: Within 1 sec (at 33⅓ rpm)

Tone Arm:
• Arm Type: Universal type S-shape tone arm, Gimbal-supported type bearing structure, Static balance type
• Overhang: 0.63 in
• Effective Length: 9.07 in
• Tracking Error: Within 3°
• Height Adjustment Range: 0.24 in
• Stylus Pressure Variable Range: 0-4 g (1 scale 0.1 g)
• Cartridge Weight Single: < 9.5 g
• Cartridge type: VM

Terminals:
• Outputs: 1 PHONO/LINE (RCA)
• USB: 1 USB B port

Fits Pioneer PLX-1000, PLX-500 and Technics SL-1200/1210 Mk1, Mk2, Mk3, Mk4, Mk5, Mk5G & Mk6 turntables. Designed and engineered in the UK. Sleek smoked/clear polycarbonate shell provides high level of protection, preserving the lifespan of your turntable. Simple push fit design shields tone-arm from accidental damage whilst making allowances for cables, your turntable can sit ready for operation. At home, on the road or in the club, Decksaver has your turntable covered.

Weight: 0.633 kg
Cover Dimension 45.6 × 35.5 × 7.5 cm
Fits: Technics SL-1200, SL-1210 (MK1-MK7/GR), Pioneer PLX-1000, PLX-CRSS12 and Mixars LTA/STA, Germini PT1000 turntables

The Technics 12" Vinyl BackBag offers three carry options: Ether you carry your vinyl goodies in a backback, shoulder bag or as a case. The Technics 12" Vinyl BackBags grabs 60 12 inch records, so it's large enough for a DJ set or extensive digging trips.

Technics 12" Vinyl BackBag - features:

• Technics logo embroidery
• sturdy construction
• front pocket for cell phone
• accessories front compartment
• removable shoulder strap
• weight: approx. 1.090 g

The Technics 12" Vinyl BackBag offers three carry options: Ether you carry your vinyl goodies in a backback, shoulder bag or as a case. The Technics 12" Vinyl BackBags grabs 60 12 inch records, so it's large enough for a DJ set or extensive digging trips.

Technics 12" Vinyl BackBag - features:

• Technics logo embroidery
• sturdy construction
• front pocket for cell phone
• accessories front compartment
• removable shoulder strap
• weight: approx. 1.090 g