Cartridges 83 Items

The AT-VM95C, the new Audio-Technica entry model Conical cartridge will replace the legendary AT90 Series models such as AT91, AT91R and CN5625AL

Also the AT-VM95C is a “budget” cartridge featuring a conical stylus, the compatibility in the range will allow to upgrade with any of the 4 other LP styli of the Series such as Elliptical, Elliptical Nude, Microlinear and Shibata.

Aluminium cantilever
4.0mV output voltage
Compatible body with all VM95 Series stylus assemblies
Replacement for AT91, AT91R and CN5625AL

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

CONICAL BONDED STYLUS
The benefit of conical styli, even if the cartridge is "lean", is the ball surface of the stylus touches the groove of vinyl records precisely.

Model AT-VM95C
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 20,000 Hz
Kanaltrennung 18 dB (1 kHz)
Kanalbalance am Ausgang 2.5 dB (1 kHz)
Ausgangsleistung 4.0 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Conical
Nadelabmessungen 0.6 mil
Schaftform der Nadel Bonded Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 17 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 6.5 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95C
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers

AT-VM95C/H
VM95 SERIES CONICAL STEREO CARTRIDGE ON AT-HS6 HEADSHELL
AT-VM95C mounted on AT-HS6BK headshell
The total set weight is 15.5g
Assembled and tested in the Audio-Technica Factory in Fukui-Japa

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

CONICAL BONDED STYLUS
The benefit of conical styli, even if the cartridge is "lean", is the ball surface of the stylus touches the groove of vinyl records precisely.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95C cartridge is fitted onto the 9g aluminium die cast body headshell

Model AT-VM95C/H
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 20,000 Hz
Kanaltrennung 18 dB (1 kHz)
Kanalbalance am Ausgang 2.5 dB (1 kHz)
Ausgangsleistung 4.0 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Conical
Nadelabmessungen 0.6 mil
Schaftform der Nadel Bonded Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 17 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 6.5 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 15.5 g
Abmessungen 21.2 × 21.4 × 62.4 ( H x W x D mm)
Ersatznadel AT-VMN95C

Der AT-VM95E ist das neue
Einstiegsmodell von Audio-Technica mit
elliptischer Nadel, das nicht nur den
legendären AT95E ersetzt, sondern auch
von den Entwicklungen des im Jahr 2015
eingeführten AT95EX profitiert.
Der AT-VM95E überzeugt durch ein
optimiertes, markantes Design mit steiferem,
resonanzarmem Gehäuse und – dank zwei
Gewindeeinsätzen im Gehäuse – eine
besonders einfache Montage mit nur zwei
Schrauben, ohne Muttern (mit Headshell oder
in den Tonarm integriert)

• Das Tonabnehmer-Set AT-VM95E/H wird im Audio-TechnicaWerk
in Fukui (Japan) vormontiert, getestet und verpackt.
• Gesamtgewicht 15,5 g

AT-VM95E/H
VM95 SERIES ELLIPTICAL STEREO CARTRIDGE ON AT-HS6 HEADSHELL
AT-VM95E mounted on AT-HS6BK headshell
The total set weight is 15.5g
Assembled and tested in the Audio-Technica Factory in Fukui-Japan

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

ELLIPTICAL BONDED STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95E cartridge is fitted onto the 9g aluminiumdie cast body headshell

Model AT-VM95E/H
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 22,000 Hz
Kanaltrennung 20 dB (1 kHz)
Kanalbalance am Ausgang 2.0 dB (1 kHz)
Ausgangsleistung 4.0 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Elliptical
Nadelabmessungen 0.3 x 0.7 mil
Schaftform der Nadel Bonded Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 17 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 7 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 15.5 g
Abmessungen 21.2 × 21.4 × 62.4 ( H x W x D mm)
Ersatznadel AT-VMN95E

Der AT-VM95EN besitzt eine nackte,
elliptische Diamantnadel mit Rundschaft,
die aus einem Stück geschliffen und
direkt in den Nadelträger eingesetzt
wird. Auf diese Weise lässt sich ein
leichteres, steiferes Übertragungssystem
realisieren als mit einer gefassten
Diamantnadel mit Titan-Rundschaft wie
beim AT-VM95E. Die nackte
Diamantnadel ist zwar um einiges
kostspieliger, bietet aber auch eine
hörbar bessere Audioqualität mit
besonders hoher Klangtreue bei der
Höhenwiedergabe und hervorragendem
Impulsverhalten.

Aluminium-Nadelträger
• Ausgangsspannung 3,5 mV
• Gehäuse kompatibel mit allen Abtastnadeln der Serie VM95
• Frequenzgang 20 bis 23.000 Hz

AT-VM95EN
VM95 SERIES ELLIPTICAL NUDE STEREO CARTRIDGE
The AT-VM95EN, features a Nude Elliptical Diamond. The construction of the stylus being a one piece diamond with a round shank inserted in the cantilever creates a lighter and more rigid transmission system than a diamond tip bonded on a round titanium shank such as in the AT-VM95E. Also the use of nude diamond implies a substantial difference in pricing, yet the quality of the reproduction will be immediately noticed, specifically in the fidelity of high frequencies and in the quality of the transient responses.

Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 23,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

ELLIPTICAL NUDE STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

NO USE OF NUTS
VM95 Series cartridges features two M2.6 threaded inserts allowing the installation of the cartridge onto tonearm or removable headshell without the use of nuts.Each cartridge is provided with one pair of 8mm M2.6 screws, one pair of 11mm M2.6 screws and two plastic washers.

Model AT-VM95EN
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 23,000 Hz
Kanaltrennung 22 dB (1 kHz)
Kanalbalance am Ausgang 2.0 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Elliptical
Nadelabmessungen 0.3 x 0.7 mil
Schaftform der Nadel Nude Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 7 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95EN
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

AT-VM95EN vormontiert auf Headshell AT-HS6BK
• Das Tonabnehmer-Set AT-VM95EN/H wird im Audio-Technica Werk in Fukui (Japan) vormontiert, getestet und verpackt.
Gesamtgewicht 15,5 g

Der AT-VM95EN besitzt eine nackte,
elliptische Diamantnadel mit Rundschaft,
die aus einem Stück geschliffen und
direkt in den Nadelträger eingesetzt
wird. Auf diese Weise lässt sich ein
leichteres, steiferes Übertragungssystem
realisieren als mit einer gefassten
Diamantnadel mit Titan-Rundschaft wie
beim AT-VM95E. Die nackte
Diamantnadel ist zwar um einiges
kostspieliger, bietet aber auch eine
hörbar bessere Audioqualität mit
besonders hoher Klangtreue bei der
Höhenwiedergabe und hervorragendem
Impulsverhalten.

Aluminium-Nadelträger
• Ausgangsspannung 3,5 mV
• Gehäuse kompatibel mit allen Abtastnadeln der Serie VM95
• Frequenzgang 20 bis 23.000 Hz

AT-VM95EN
VM95 SERIES ELLIPTICAL NUDE STEREO CARTRIDGE
The AT-VM95EN, features a Nude Elliptical Diamond. The construction of the stylus being a one piece diamond with a round shank inserted in the cantilever creates a lighter and more rigid transmission system than a diamond tip bonded on a round titanium shank such as in the AT-VM95E. Also the use of nude diamond implies a substantial difference in pricing, yet the quality of the reproduction will be immediately noticed, specifically in the fidelity of high frequencies and in the quality of the transient responses.

Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 23,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

ELLIPTICAL NUDE STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95E cartridge is fitted onto the 9g aluminiumdie cast body headshell

Model AT-VM95EN
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 23,000 Hz
Kanaltrennung 22 dB (1 kHz)
Kanalbalance am Ausgang 2.0 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Elliptical
Nadelabmessungen 0.3 x 0.7 mil
Schaftform der Nadel Nude Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 7 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95EN
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

Der AT-VM95ML ist mit einem nackten
Microlinear-Diamanten ausgestattet, der
durch seinen speziellen Schliff und die für
Line-Contact-Nadeln typischen
geringeren Verzerrungen am Plattenende
(innere Rillen) eine doppelt so hohe
Lebensdauer gewährleistet und sich
zugleich durch einen erweiterten
Frequenzgang und eine bessere
Auflösung der mittleren und hohen
Frequenzen auszeichnet.

AT-VM95ML
VM95 SERIES MICROLINEAR STEREO CARTRIDGE
The AT-VM95ML, features a Nude Microlinear diamond, not only the Microlinear stylus will permit to double the duration of your stylus. The performance of a line contact stylus, will minimize the “inner groove distortion” as well as providing extended frequency response and maximize resolution in the medium and high frequencies of the audio program material.

material. Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 25,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

MICROLINEAR STYLUS
Microlinear profile diamond stylus offers high frequency response with less wear and distortion than elliptical or conventional linear contact styli.

NO USE OF NUTS
VM95 Series cartridges features two M2.6 threaded inserts allowing the installation of the cartridge onto tonearm or removable headshell without the use of nuts.Each cartridge is provided with one pair of 8mm M2.6 screws, one pair of 11mm M2.6 screws and two plastic washers.

Model AT-VM95ML
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 25,000 Hz
Kanaltrennung 23 dB (1 kHz)
Kanalbalance am Ausgang 1.5 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Microlinear
Nadelabmessungen 2.2 x 0.12 mil
Schaftform der Nadel Nude Square Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 10 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95ML
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

Der AT-VM95ML ist mit einem nackten
Microlinear-Diamanten ausgestattet, der
durch seinen speziellen Schliff und die für
Line-Contact-Nadeln typischen
geringeren Verzerrungen am Plattenende
(innere Rillen) eine doppelt so hohe
Lebensdauer gewährleistet und sich
zugleich durch einen erweiterten
Frequenzgang und eine bessere
Auflösung der mittleren und hohen
Frequenzen auszeichnet.

AT-VM95C/H
VM95 SERIES MICROLINEAR STEREO CARTRIDGE ON AT-HS6 HEADSHELL
AT-VM95ML mounted on AT-HS6BK headshell
The total set weight is 15.5g
Assembled and tested in the Audio-Technica Factory in Fukui-Japan

AT-VM95ML
VM95 SERIES MICROLINEAR STEREO CARTRIDGE
The AT-VM95ML, features a Nude Microlinear diamond, not only the Microlinear stylus will permit to double the duration of your stylus. The performance of a line contact stylus, will minimize the “inner groove distortion” as well as providing extended frequency response and maximize resolution in the medium and high frequencies of the audio program material.

material. Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 25,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

MICROLINEAR STYLUS
Microlinear profile diamond stylus offers high frequency response with less wear and distortion than elliptical or conventional linear contact styli.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95C cartridge is fitted onto the 9g aluminium die cast body headshell

Model AT-VM95ML
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 25,000 Hz
Kanaltrennung 23 dB (1 kHz)
Kanalbalance am Ausgang 1.5 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Microlinear
Nadelabmessungen 2.2 x 0.12 mil
Schaftform der Nadel Nude Square Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 10 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95ML
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

Der AT-VM95SH besitzt eine nackte
Shibata-Nadel – hochgeschätzt
insbesondere für audiophile HighendAnwendungen.
Der Shibata-Schliff ermöglicht satte,
volle Bässe und Mitten und einen
Frequenzgang bis 25.000 Hz.

AT-VM95SH
VM95 SERIES SHIBATA STEREO CARTRIDGE
The AT-VM95SH, features a Nude Shibata stylus, one of the most acclaimed stylus format by high end audiophiles. The Shibata stylus produces mid and bass sounds strong and rich in addition to offer a frequency response up to 25,000 Hz.

Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 25,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

SHIBATA STYLUS
Provides a beautiful mid-high range Shibata-signature sound and strong mid-range volume.

NO USE OF NUTS
VM95 Series cartridges features two M2.6 threaded inserts allowing the installation of the cartridge onto tonearm or removable headshell without the use of nuts.Each cartridge is provided with one pair of 8mm M2.6 screws, one pair of 11mm M2.6 screws and two plastic washers.

Model AT-VM95SH
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 25,000 Hz
Kanaltrennung 23 dB (1 kHz)
Kanalbalance am Ausgang 1.5 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Microlinear
Nadelabmessungen 2.7 x 0.26mil
Schaftform der Nadel Nude Square Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 10 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95SH
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

Der AT-VM95SH besitzt eine nackte
Shibata-Nadel – hochgeschätzt
insbesondere für audiophile HighendAnwendungen.
Der Shibata-Schliff ermöglicht satte,
volle Bässe und Mitten und einen
Frequenzgang bis 25.000 Hz.

AT-VM95SH
VM95 SERIES SHIBATA STEREO CARTRIDGE
The AT-VM95SH, features a Nude Shibata stylus, one of the most acclaimed stylus format by high end audiophiles. The Shibata stylus produces mid and bass sounds strong and rich in addition to offer a frequency response up to 25,000 Hz.

Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 25,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

SHIBATA STYLUS
Provides a beautiful mid-high range Shibata-signature sound and strong mid-range volume.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95C cartridge is fitted onto the 9g aluminium die cast body headshell

Model AT-VM95SH
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 25,000 Hz
Kanaltrennung 23 dB (1 kHz)
Kanalbalance am Ausgang 1.5 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Microlinear
Nadelabmessungen 2.7 x 0.26mil
Schaftform der Nadel Nude Square Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 10 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95SH
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

AT-XP5
DUAL MOVING MAGNET STEREO CARTRIDGE

• Excellent Tracking ability
• Superior sound without compromise
• Designed for DJ venue application for their Hi-Fi audio performance
• Durable robust design for high-quality DJ playback
• Great visibility of stylus tip for instant positioning
• Carbon ABS cantilever

The AT-XP5 is specially designed for the needs of DJs. This cartridge features a highly-rigid polyphenylene sulfide (PPS)/glass fiber body and a tracking force of 2 to 4 grams. It also offers a powerful output level of 5.5 mV, and its 0.3 x 0.7 mil elliptical bonded stylus tracks the record groove with high accuracy for outstanding audio reproduction. Plus, the cartridge is specifically designed to provide maximum visibility of the stylus tip.

• Durable design for high-quality specialist DJ playback
• Cartridges designed for DJ venue applications for their Hi Fi audio Performance
• VM dual magnet cartridge with 0.3 x 0.7 mil elliptical bonded stylus
• Audiophile experience associated with DJ’ing environment with the signal output level and output impedance characteristics adapted to DJ professional mixing boards
• Carbon ABS cantilever
• Great visibility of stylus tip for DJ use
• High-rigidity and Low-resonance cartridge housing
• Durable design for high-quality DJ playback
• Replacement Stylus: ATN-XP5

Specifications:
• Type: VM Dual Magnet
• Frequency Response: 20 - 18,000 Hz
• Channel Separation: 20 dB at 1kHz
• Vertical Tracking Angle: 20°
• Vertical Tracking Force: 2.0 to 4.0 g (standard 3g)
• Recommended Load Impedance: 47,000 ohms
• Coil Inductance: 1.0 H (1 kHz)
• Output Voltage: 5.5 mV (mV at 1 kHz, 5 cm/sec)
• Output Channel Balance: 2.0 dB
• Stylus Shape: Elliptical
• Cantilever: Carbon Fibre Reinforced ABS
• Static Compliance: 20 x 10-6 cm/dyne
• Dynamic Compliance: 6.0x10-6cm/dyne (100Hz)
• Mounting: Half-inch
• Dimensions: H17.2×W17.8×D28.3mm
• Accessories Included: Cartridge installation slotted screws 11.0 mm (0.43”) x 2 and 8.0 mm (0.31”) x 2, Washer x 2, Round nut x 2, Non-magnetic screwdriver x 1
• Recommended Load Capacitance: 100-200 pF
• Replacement Stylus: ATN-XP5
• Stylus Size: 0.3 x 0.7 mil
• Weight: 6.2g

Manual: https://eu.audio-technica.com/resources/AT-XP5_UM_112301370_V1_11L_web_171018.pdf

VM510CB
DUAL MOVING MAGNET STEREO CARTRIDGE WITH CONICAL STYLUS
Conical Bonded stylus
VM type dual magnet system
Para-toroidal coils improve generating efficiency
Aluminium cantilever
Centre shield plate between stereo channels
Durable low resonance polymer housing

Conical Bonded stylus for less critical tilt angle adjustment allowing more flexible use on various tonearms.
VM type dual magnet design ensures outstanding channel separation, extended frequency response and superb tracking
Lightweight tapered aluminium cantilever allows for faithful reading of the record groove
Centre shield plate enables the effective separation of left and right channels, suppressing electrical crosstalk to below 40dB
Durable low resonance polymer housing

Entry-level VM cartridge model equipped with a conical bonded stylus. The round stylus is less likely to be affected by placement and boasts stable tracing performance.

Aluminium cantilever
Para-toroidal coils improve generating efficiency
Centre shield plate between the left and right channels reduces crosstalk
Durable low resonance polymer housing

AUDIO-TECHNICA’S INTERNATIONALLY-PATENTED DUAL MAGNET DESIGN REPLICATES THE STRUCTURE OF THE CUTTER HEAD.
Instead of using a single, large magnet, the two magnets are arranged in the shape of a "V". The two magnets are positioned precisely to match the positions of the left and right channels in the stereo groove walls. Consequently, the VM design ensures outstanding channel separation, extended frequency response and superb tracking.

Para-toroidal generating system

Para-toroidal coils improve generating efficiency and offers superb linearity, since leakage of magnetic flux in this continuous and unitised magnetic circuit is low. Permeability of the cores is also optimised through the use of laminated cores.

Centre shield plate reduces crosstalk

A permalloy centre shield plate enables the effective separation of left and right channels, suppressing electrical crosstalk to below 40dB. This is similar to the actual crosstalk value found in the grooves of the record itself.

500 SERIES
Standard cartridge body fitted with the para-toroidal coils, centre shield plate, and 6N-OFC coil wire which is the same as 700 series.

CONICAL BONDED STYLUS
The benefit of conical styli, even if the cartridge is "lean", is the ball surface of the stylus touches the groove of vinyl records precisely. Due to its stability, it has been used widely at radio stations.

Type VM Type
Mounting 1/2” centres
Frequency Response 20 - 20,000Hz
Channel Separation 25dB (1kHz)
Output Channel Balance 1.5dB (1kHz)
Output Voltage 5.0mV (1kHz, 5cm/sec.)
Vertical Tracking Angle 23˚
Vertical Tracking Force Range 1.8 – 2.2g (2.0g standard)
Stylus Shape Conical Bonded
Stylus Size 0.6 mil
Stylus Construction Bonded Round Shank
Cantilever Aluminium Pipe
Coil Impedance 2,700Ω (1kHz)
Static Compliance 35 x 10-6 cm/dyne
Dynamic Compliance 8 x 10-6 cm/dyne (100Hz)
Recommended Load Impedance 47,000Ω
Recommended Load Capacitance 100 – 200pF
Weight 6.4g
Dimensions 17.3 (H) x 17.0 (W) x 28.2 (L) mm
Replacement Stylus VMN10CB
Accessories Included Cartridge installation screws 5mm ×2 and 10mm ×2, Washer ×2, Hexagon nut ×2

VM Cartridges: https://eu.audio-technica.com/resources/VM_Cartridges_EN.pdf

Manual: https://eu.audio-technica.com/resources/VM/VM510CB_UM_V2_11L_web_161011.pdf

VM520EB
DUAL MOVING MAGNET STEREO CARTRIDGE WITH ELLIPTICAL STYLUS
Elliptical Bonded profile diamond stylus
VM type dual magnet system
Para-toroidal coils improve generating efficiency
Aluminium cantilever
Centre shield plate between stereo channels
Durable low resonance polymer housing

Standard elliptical stylus model equipped with an elliptical bonded stylus. This reduces tracing distortion and allows for more accurate sound reproduction.

Aluminium cantilever
Para-toroidal coils improve generating efficiency
Centre shield plate between the left and right channels reduces crosstalk
Durable low resonance polymer housing

AUDIO-TECHNICA’S INTERNATIONALLY-PATENTED DUAL MAGNET DESIGN REPLICATES THE STRUCTURE OF THE CUTTER HEAD.
Instead of using a single, large magnet, the two magnets are arranged in the shape of a "V". The two magnets are positioned precisely to match the positions of the left and right channels in the stereo groove walls. Consequently, the VM design ensures outstanding channel separation, extended frequency response and superb tracking.

Para-toroidal generating system

Para-toroidal coils improve generating efficiency and offers superb linearity, since leakage of magnetic flux in this continuous and unitised magnetic circuit is low. Permeability of the cores is also optimised through the use of laminated cores.

Centre shield plate reduces crosstalk

A permalloy centre shield plate enables the effective separation of left and right channels, suppressing electrical crosstalk to below 40dB. This is similar to the actual crosstalk value found in the grooves of the record itself.

500 SERIES
Standard cartridge body fitted with the para-toroidal coils, centre shield plate, and 6N-OFC coil wire which is the same as 700 series.

ELLIPTICAL BONDED STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

Type VM Type
Mounting 1/2” centres
Frequency Response 20 - 23,000Hz
Channel Separation 27dB (1kHz)
Output Channel Balance 1.5dB (1kHz)
Output Voltage 4.0mV (1kHz, 5cm/sec.)
Vertical Tracking Angle 23˚
Vertical Tracking Force Range 1.8 – 2.2g (2.0g standard)
Stylus Shape Elliptical Bonded
Stylus Size 0.3 x 0.7 mil
Stylus Construction Bonded Round Shank
Cantilever Aluminium Pipe
Coil Impedance 2,700Ω (1kHz)
Static Compliance 35 x 10-6 cm/dyne
Dynamic Compliance 8 x 10-6 cm/dyne (100Hz)
Recommended Load Impedance 47,000Ω
Recommended Load Capacitance 100 – 200pF
Weight 6.4g
Dimensions 17.3 (H) x 17.0 (W) x 28.2 (L) mm
Replacement Stylus VMN20EB
Accessories Included Cartridge installation screws 5mm ×2 and 10mm ×2, Washer ×2, Hexagon nut ×2

VM Cartridges: https://eu.audio-technica.com/resources/VM_Cartridges_EN.pdf

Manual: https://eu.audio-technica.com/resources/VM/VM520EB_UM_V2_11L_web_161021.pdf

VM530EN
DUAL MOVING MAGNET STEREO CARTRIDGE WITH ELLIPTICAL STYLUS
Elliptical Nude profile diamond stylus
VM type dual magnet system
Para-toroidal coils improve generating efficiency
Aluminium cantilever
Centre shield plate between stereo channels
Durable low resonance polymer housing

High-end elliptical stylus model equipped with a light-weight nude elliptical stylus to reduce the execution mass of the vibration system. This enables fuller frequency reproduction.

Aluminium cantilever
Para-toroidal coils improve generating efficiency
Centre shield plate between the left and right channels reduces crosstalk
Durable low resonance polymer housing

AUDIO-TECHNICA’S INTERNATIONALLY-PATENTED DUAL MAGNET DESIGN REPLICATES THE STRUCTURE OF THE CUTTER HEAD.
Instead of using a single, large magnet, the two magnets are arranged in the shape of a "V". The two magnets are positioned precisely to match the positions of the left and right channels in the stereo groove walls. Consequently, the VM design ensures outstanding channel separation, extended frequency response and superb tracking.

Para-toroidal generating system

Para-toroidal coils improve generating efficiency and offers superb linearity, since leakage of magnetic flux in this continuous and unitised magnetic circuit is low. Permeability of the cores is also optimised through the use of laminated cores.

Centre shield plate reduces crosstalk

A permalloy centre shield plate enables the effective separation of left and right channels, suppressing electrical crosstalk to below 40dB. This is similar to the actual crosstalk value found in the grooves of the record itself.

500 SERIES
Standard cartridge body fitted with the para-toroidal coils, centre shield plate, and 6N-OFC coil wire which is the same as 700 series.

ELLIPTICAL NUDE STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

Type VM Type
Mounting 1/2” centres
Frequency Response 20 - 25,000Hz
Channel Separation 27dB (1kHz)
Output Channel Balance 1.5dB (1kHz)
Output Voltage 4.0mV (1kHz, 5cm/sec.)
Vertical Tracking Angle 23˚
Vertical Tracking Force Range 1.8 – 2.2g (2.0g standard)
Stylus Shape Elliptical Nude
Stylus Size 0.3 x 0.7 mil
Stylus Construction Nude Round Shank
Cantilever Aluminium Pipe
Coil Impedance 2,700Ω (1kHz)
Static Compliance 35 x 10-6 cm/dyne
Dynamic Compliance 8 x 10-6 cm/dyne (100Hz)
Recommended Load Impedance 47,000Ω
Recommended Load Capacitance 100 – 200pF
Weight 6.4g
Dimensions 17.3 (H) x 17.0 (W) x 28.2 (L) mm
Replacement Stylus VMN30EN
Accessories Included Cartridge installation screws 5mm ×2 and 10mm ×2, Washer ×2, Hexagon nut ×2, Non-magnetic screwdriver ×1, Brush ×1

VM Cartridges: https://eu.audio-technica.com/resources/VM_Cartridges_EN.pdf

Manual: https://eu.audio-technica.com/resources/VM/VM530EN_UM_V2_11L_web_161021.pdf

Clearaudio’s V2 MM technology uses ebony as a resonanceresistant body. Other ingredients of the recipe for success are the most effective reduction of moving mass, an optimised polishing technique for the stylus and highly effective cartridge damping. This is precision engineering in the pursuit of the best sound.

The Clearaudio V2 moving magnet cartridges are meticulously measured, analysed, and hand-selected into four Performance levels. In this way Clearaudio achieves the best stereo channel
matching, minimum phase error and distortion, flattest frequency response and highest dynamic range at each price point. The cartridges produce an audiophile sound of superlative quality – spatially detailed and vividly textured, with bass that does not wallow and treble that is not harsh.

The models of the Clearaudio MM V2 series provide outstanding sound quality on all current tonearms. With the exception of the MM V2 Concept, which is made of aluminium, all the cartridges in this series are made with housings of hand-polished ebony – the key to record-breaking weight values. The Performer V2 weighs just 7.4 grams, the Artist V2 8.4 grams. This is what Clearaudio calls ‘effective reduction of the moving mass’.

FEATURES
Technical Specifications:
• TOTAL MASS 8.6g (± 0.2g)
• FREQUENCY RESPONSE 20Hz - 20kHz
• OUTPUT VOLTAGE (1KHZ, 5CM/S) ~ 3.3mV
• CHANNEL SEPARATION (1KHZ) 20dB
• CHANNEL BALANCE (1KHZ) 2dB
• TRACKING ABILITY 80μm
• RECOMMENDED TRACKING FORCE 2.2g ± 0.3g
• COIL IMPEDANCE (1KHZ) 0.66kΩ
• COIL INDUCTANCE 400mH
• LOAD RESISTANCE 47kΩ
• LOAD CAPACITANCE 100pF
• CANTILEVER / STYLUS SHAPE Aluminium / elliptical
• COMPLIANCE 15μ/mN
• CARTRIDGE BODY Aluminium
• MANUFACTURER’S WARRANTY 2 years

Manual: https://clearaudio.de/_assets/_pdf/manuals/cartridges/CA_MM%20V2_E+D.pdf?d=1653493472

Goldring E2

The Goldring philosophy is to promote the accurate replication of the original record production, maintaining the creative nuances, musicality and rhythm the artist intended you to hear. With the versatile E Series, this is easy to achieve; each is designed to be simple to fit to the majority of budget to medium priced turntables.

The E2 cartridge, the middle in the range, features the same spherical stylus profile as the E1 but with the additional benefit of an upgraded aluminium cantilever. This is both stiff and light weight allowing the stylus to more accurately trace medium to high frequencies offering more detail and reducing distortion and mis-tracking during loud passages.

Magnetic Duplex Technology™
All cartridges in the range feature Magnetic Duplex Technology™-a 'dual magnet' generator assembly with an identical geometry to that of the original cutting head. This means it can more accurately reproduce the stereo information in the record groove, providing better channel separation and a more involving and musical sound stage.

Expert Adjustment
The E-series cartridges have been designed to allow micro-adjustments to be made during production using a special adjustment screw. This means the cartridge can be safely installed in a typical turntable because the angle that the stylus makes with the record surface has been pre-set. The result is an optimised channel balance with zero degrees of horizontal tracking adjustment required. This ensures a consistent and reassuring performance for the life of the product.

Stylus/Cantilever
Featuring spherical styli with a choice of cantilevers, the E1 and E2 models are ideal as an upgrade to any budget, pre-fitted or obsolete cartridge. The E3 model with its re­fined super elliptical stylus is a worthwhile upgrade for those wishing to squeeze even more information and detail from the record groove.

• Colour: Green
• Cantilever: Aluminium
• Stylus profile: Spherical
• Stylus radius: 0.6 mil
• Frequency range: 20 Hz - 20 kHz
• Channel balance: 1.5 dB at 1 kHz
• Channel separation: >20 dB at 1 kHz
• Sensitivity: 3.5 mV (1 kHz @ 5 cm/sec)
• Static compliance: 20 mm/N
• Vertical tracking angle: 20°
• Load resistance: 47 kΩ
• Load capacitance: 100 - 200 pF
• Internal inductance: 400 mH
• Internal resistance: 410 Ω
• Cartridge mass: 6.9 g
• Fixing centres: 12.7 mm (0.5 in)
• Playing weight: 1.5 g - 2.5 g (2.0 g recommended)

Goldring E3

The Goldring philosophy is to promote the accurate replication of the original record production, maintaining the creative nuances, musicality and rhythm the artist intended you to hear. With the versatile E Series, this is easy to achieve; each is designed to be simple to fit to the majority of budget to medium priced turntables.

The E3 cartridge, representing the top of the range features the same aluminium cantilever as the E2, but benefits from a superior, bonded, super-elliptical (0.3 x 0.7 mil) stylus. This gives it better high frequency detail retrieval over ordinary elliptical (0.4 x 0.7 mil) or spherical (0.6 mil) types due to its smaller front-to-back radius. The main effect is the reduction of sibilance, especially in high level vocal recordings

Magnetic Duplex Technology™
All cartridges in the range feature Magnetic Duplex Technology™-a 'dual magnet' generator assembly with an identical geometry to that of the original cutting head. This means it can more accurately reproduce the stereo information in the record groove, providing better channel separation and a more involving and musical sound stage.

Expert Adjustment
The E-series cartridges have been designed to allow micro-adjustments to be made during production using a special adjustment screw. This means the cartridge can be safely installed in a typical turntable because the angle that the stylus makes with the record surface has been pre-set. The result is an optimised channel balance with zero degrees of horizontal tracking adjustment required. This ensures a consistent and reassuring performance for the life of the product.

Stylus/Cantilever
Featuring spherical styli with a choice of cantilevers, the E1 and E2 models are ideal as an upgrade to any budget, pre-fitted or obsolete cartridge. The E3 model with its re­fined super elliptical stylus is a worthwhile upgrade for those wishing to squeeze even more information and detail from the record groove.

• Colour: Violet
• Cantilever: Aluminium
• Stylus profile: Elliptical
• Stylus radius: 0.3 x 0.7 mil
• Frequency range: 20 Hz - 20 kHz
• Channel balance: 1.5 dB at 1 kHz
• Channel separation: >20 dB at 1 kHz
• Sensitivity: 3.5 mV (1 kHz @ 5 cm/sec)
• Static compliance: 20 mm/N
• Vertical tracking angle: 20°
• Load resistance: 47 kΩ
• Load capacitance: 100 - 200 pF
• Internal inductance: 400 mH
• Internal resistance: 410 Ω
• Cartridge mass: 6.9 g
• Fixing centres: 12.7 mm (0.5 in)
• Playing weight: 1.5 g - 2.5 g (2.0 g recommended)

The Goldring 1006 is designed for owners who want to get the very best from their systems at a budget price. This cartridge has an elliptical tip for improved high frequency clarity and a powerful magnet to ensure high sensitivity.

This hand-built cartridge features an elliptical stylus; its shape enables it to more accurately trace the highest frequency record grooves giving it the advantage over ordinary spherical types. The lightweight shank also gives the stylus a lower tip mass than cheaper metal bonded types lending the cartridge an improved transient response.

Low Mass Pocan® Body
The 1000 series uses a strong one piece body which holds the fixed parts securely in place. Made from a special type of ultra-rigid, glass reinforced polyester called Pocan, the body can be tightly bolted to the head shell for maximum efficiency and optimum sound quality. The user replaceable stylus carrier slots tightly into the body with a locating pin preventing unwanted vibrations which would otherwise colour the sound. An integral mu-metal can keeps the generator parts shielded from hum-inducing stray magnetic fields. Because Pocan has a high strength-to-mass ratio, the overall mass of the G1000 series cartridges is kept below 6.5 g. Low mass and moderate compliance keep the natural arm/cartridge resonance within safe limits for easy matching to a wide range of tonearms.

High Efficiency Magnetic Circuit
Finely etched mu-metal is laminated to form the pole pieces around which are fitted two formerless coils of four thousand turns each. This unique design reduces mass and also makes for a very efficient magnetic circuit producing a higher than average output. This construction also reduces the loss at high frequencies inherent in conventional designs, making for a smooth and extended frequency response.

Reduced Moving Mass
The 1000 series uses a unique ultra-low-mass, micro-miniature Alnico V magnet made to a tolerance that can be achieved by no other manufacturer worldwide. Welded to the magnet is a gold plated nickel tie-bar which provides an earth path for vinyl static charge build up and stabilses the cantilever in unwanted vibrational modes. The whole ultra-low-mass assembly is then mounted in a special butyl rubber polymer with optimised damping characteristics.

Expert Adjustment
The correct setting of stylus azimuth (or horizontal tracking angle) is essential for the maintenance of a proper stereo sound stage. Azimuth is the term used to describe the angle that the vertical centre-line of the stylus makes with the record surface and this must be exactly perpendicular to the record groove. This is not usually a user adjustable parameter on most budget decks and so it is vital that the cartridge leaves the factory with the azimuth precisely set. Badly adjusted azimuth can cause uneven channel balance and increased crosstalk between channels which would severely degrade the stereo image.

Specifications:
• Frequency Response: 20 Hz -20 kHz ±3 dB
• Channel Balance: within 2 dB @ 1 kHz
• Channel Separation: better than 25 dB @ 1 kHz
• Sensitivity: 6.5 mV ±1.5 dB, 1 kHz @ 5 cm/sec
• Static Compliance: 24 mm/N (lat); 16 mm/N (vert)
• Equivalent tip mass: 0.45 mg
• Vertical Tracking Angle: 24°
• Stylus Radius: Elliptical
• Stylus Type: Replaceable
• Load Resistance: 47 kΩ
• Load Capacitance: 150-200 pF
• Internal Inductance: 570 mH
• Internal Resistance: 660 Ω
• Cartridge Mass: 6.3 g
• Cartridge Mass (inc. fixings): 7.6 g
• Fixing Centre: 0.5" (12.7 mm)
• Playing Weight: 1.5 - 2.0 g (1.7 g nom.)
• Replacement Stylus: 1006 - D0

DJ-03 HD - CARTRIDGE INCL. HEADSHELL

This is the Nagaoka DJ cartridge. With a high output voltage of 6 mV and a recommended tracking force of 3 - 5 g, it is one of the more stable of its kind.

TECHNICAL SPECIFICATIONS:
• Cartridge type: MM
• Configuration: Climax DS/DSM
• Output voltage: 6 mV (5 cm/sec.)
• Frequency Characteristics: 20Hz~20KHz
• Channel separation: 20 dB (1 kHz)
• Channel balance: 2 dB or less
• Load resistance: 47 kΩ
• Load: 100pF
• Cantilever: aluminum alloy
• Needle Tip: 0.6 mil tapered bonded diamond
• Recommended tracking force: 3~5g
• Pickup weight: 5.1g
• Weight with headshell: 15.1g

The Nagaoka JT-80LB (Lapis Blue) cartridge with its shiny blue needle insert is the basic model of the series and features an aluminium needle carrier with a set diamond. With its open, powerful sound, it offers exceptional value for money. The cartridge unfolds its full potential after an approx. 80-hour play-in period.

TECHNICAL SPECIFICATIONS:
• Format: Moving magnet type (MM type)
• Output: 5.0 mV (5 cm / sec)
• Frequency characteristic: 20Hz-20,000Hz
• Channel separation: 23dB (1Khz)
• Channel balance: 1.5 dB or less
• Cantilever: Aluminum alloy
• Needle tip: 0.4x0.7mil Ellipse / Joined diamond
• Stylus pressure: 1.3g-1.8g
• Torridge own weight: 6.9g
• Replacement needle: JTS-80LB
• Cartridge type: without head shell

https://www.auditorium.de/attachment/STEREO_3-21_Nagaoka-Abtaster_englisch.pdf

With its round diamond, the MP-100 cartridge is particularly suitable for older records. Even scratches and dirt do not affect the pleasant, neutral sound that this system makes possible. The MP-100 is the most affordable scanner in the MP range.

TECHNICAL SPECIFICATIONS:
• Principle: MI - High Output (for the MM input)
• Weight: 6.5g
• Height 18mm
• Needle cut: Round 0.6mm
• Cantilever: aluminum
• Frequency response: 20 - 20,000 Hz
• Output Voltage (1kHz, 5cm/sec): 5.0mV
• Channel separation (1kHz): > 22 dB
• Channel balance (1kHz): < 2.0 dB
• Needle compliance: 19 µm/mN
• Recommended tracking force: 21 mN (18-23 mN)
• Recommended termination resistance: 47 kOhm
• Recommended termination capacity: 150 – 200 pF
• Replacement needle: JN-P100
• Cartridge type: without head shell

Hear the vivid sound experience that music playback offers with Nagaoka's MP-110 tonearm. Especially in the high-frequency range, the elliptical needle cut ensures better detail resolution. This creates a live atmosphere while listening, which is otherwise known from concerts.

TECHNICAL SPECIFICATIONS:
• Principle: MI - High Output (for the MM input)
• Weight: 6.5g
• Height: 18mm
• Needle cut: Elliptical 0.4x0.7
• Cantilever: aluminum
• Frequency response: 20 - 20,000 Hz
• Output Voltage (1kHz, 5cm/sec): 5.0mV
• Channel Separation (1kHz): >23dB
• Channel balance (1kHz): < 1.5 dB
• Needle compliance: 19 µm/mN
• Recommended tracking force: 18 mN (15-20 mN)
• Recommended termination resistance: 47 kOhm
• Recommended termination capacity: 150 – 200 pF
• Replacement needle: JN-P110
• Cartridge type: without head shell

The design of the MP-150 has been significantly refined. Higher quality magnet materials, a better cantilever and a bonded diamond ensure better tracking and detail reproduction. The bass range also sounds more balanced.

TECHNICAL SPECIFICATIONS:
• Principle: MI - High Output (for the MM input)
• Weight: 6.5g
• Height: 18mm
• Needle cut: Elliptical 0.4x0.7mm
• Needle carrier: stiffened cone aluminum tube
• Frequency response: 20 - 20,000 Hz
• Output voltage (1kHz, 5cm/sec): 4.5mV
• Channel separation (1kHz): > 24 dB
• Channel balance (1kHz): < 1.5 dB
• Needle compliance: 20 µm/mN
• Recommended tracking force: 18 mN (15-20 mN)
• Recommended termination resistance: 47 kOhm
• Recommended termination capacity: 150 – 200 pF
• Replacement needle: JN-P150
• Cartridge type: without head shell

PROFESSIONAL DJ CARTRIDGE

Optimized cartridge for dance music DJ performance
The CS-1 Professional DJ Cartridge is designed and optimized for dance music. True full-range frequency response, a fine tip circular diamond stylus and high output all combine to make the CS-1 the only choice for serious dance club and mobile DJs.

FEATURES
• Frequency response: 20 to 22,000Hz
• Output: 6mV
• Channel separation nominal: 32dB
• DC resistance: 430 ohms/ch
• Inductance: 400mH/ch
• Weight: 18.0g
• Channel balance: within 1.5dB
• Tracking force: 3
• Recommended load: 47K ohms 200pf
• Stylus tip: fine circular diamond
• Application: club and mobile DJs, high output

EVERYTHING YOU NEED IN A CARTRIDGE, NOTHING YOU DON’T

Adjustable cartridge which will fit in a traditional headshell mount. Replaceable diamond tip.

• 5" mount+W36
• 0,6mil spherical diamond tip
• tracking force: 2,5g to 3,5g
• ch.separation: 26dB @ 1KHz
• output: 2,4 mV

The 2M 78 features an improved engine, which provides a high level of sonic accuracy. The stylus' tip is a Spherical diamond that is perfect for playback of 78 rpm shellac records, which require a larger stylus profile. The cartridge body is manufactured from Hopelex, which ensures high rigidity while eliminating unwanted resonances.

2M 78 uses a strapped output to deliver the same output signal from both sets of pole pins. This effectively eliminates the need for mono-specific equipment, making it possible to enjoy true mono reproduction on any stereo playback system.

The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M 78 Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4 mV
• Frequency response - 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 70 µm
• Compliance, dynamic, lateral - 18 µm/mN
• Stylus type - Spherical
• Stylus tip radius - R 65 µm
• Tracking force range - 1.6-2.0g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Internal impedance, DC resistance - 700 Ohm
• Internal inductance - 350 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Tracking angle - 20°
• Cartridge colour, body/stylus - Black/Grey
• Cartridge weight without screws - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M 78 (interchangeable with 2M Mono)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

The 2M Series is developed in conjunction with the Danish Industrial designer Møller Jensen Design – the same designer who designed the award winning MC Jubilee and Kontrapunkt series. Inspired by the facets of a diamond, whose contours gracefully trace the grooves on a record’s surface, the 2M’s handsome elegance establishes a great combination of form and functionality.

The name 2M was selected from among several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.

Of course the 2M isn’t just another pretty face. It has been engineered to the highest standards and is congruent with Ortofon’s unrelenting commitment to providing the most precise and accurate reproduction possible without coloration.

The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Blue features:

• an improved engine, which provides an increased output of 5.5mV and an optimized sound reproduction and a high level of sonic accuracy

• Nude Elliptical diamond and split pole pins with a copper wire

• The cartridge body is manufactured from Hopelex, an environment-friendly material which ensures high rigidity while eliminating unwanted resonances

2M Blue adds more dynamics and resolution, sounds more open and reproduces more details than 2M Red

Output voltage at 1000 Hz, 5cm/sec. - 5,5 mV
Channel balance at 1 kHz - 1,5 dB
Channel separation at 1 kHz - 25 dB
Channel separation at 15 kHz - 15 dB
Frequency range at - 3dB - 20-25.000 Hz
Frequency response - 20-20.000 Hz + 2 / - 1 dB
Tracking ability at 315Hz at recommended tracking force - 80 µm
Compliance, dynamic, lateral - 20 µm/mN
Stylus type - Nude Elliptical
Stylus tip radius - r/R 8/18 µm
Tracking force range - 1,6-2,0g (16-20 mN)
Tracking force, recommended - 1,8 g (18 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1,3 kOhm
Internal inductance - 700 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 150-300 pF
Cartridge colour, body/stylus - Black/Blue
Cartridge weight - 7,2 g
Replacement stylus unit - 2M Blue (interchangeable with 2M Red and 2M Silver)

Each of the 2M Series cartridges has its own individual sonic expression, and all five models together represent the ensemble of five classic variations:

• 2M Mono SE, 2M Mono and 2M 78 are a true mono cartridges for playing mono vinyl records
• 2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth
• 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details
• 2M Bronze adds even more details and resolution but in a very evenhanded way that pays respect to all elements
• 2M Black is the best of everything, true to the groove with resolution and accurate insight into each recording

The 2M Series is developed in conjunction with the Danish Industrial designer Møller Jensen Design – the same designer who designed the award winning MC Jubilee and Kontrapunkt series. Inspired by the facets of a diamond, whose contours gracefully trace the grooves on a record’s surface, the 2M’s handsome elegance establishes a great combination of form and functionality.

The name 2M was selected from among several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.

Of course the 2M isn’t just another pretty face. It has been engineered to the highest standards and is congruent with Ortofon’s unrelenting commitment to providing the most precise and accurate reproduction possible without coloration.

The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Blue features:

• an improved engine, which provides an increased output of 5.5mV and an optimized sound reproduction and a high level of sonic accuracy

• Nude Elliptical diamond and split pole pins with a copper wire

• The cartridge body is manufactured from Hopelex, an environment-friendly material which ensures high rigidity while eliminating unwanted resonances

2M Blue adds more dynamics and resolution, sounds more open and reproduces more details than 2M Red

Output voltage at 1000 Hz, 5cm/sec. - 5,5 mV
Channel balance at 1 kHz - 1,5 dB
Channel separation at 1 kHz - 25 dB
Channel separation at 15 kHz - 15 dB
Frequency range at - 3dB - 20-25.000 Hz
Frequency response - 20-20.000 Hz + 2 / - 1 dB
Tracking ability at 315Hz at recommended tracking force - 80 µm
Compliance, dynamic, lateral - 20 µm/mN
Stylus type - Nude Elliptical
Stylus tip radius - r/R 8/18 µm
Tracking force range - 1,6-2,0g (16-20 mN)
Tracking force, recommended - 1,8 g (18 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1,3 kOhm
Internal inductance - 700 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 150-300 pF
Cartridge colour, body/stylus - Black/Blue
Cartridge weight - 7,2 g
Replacement stylus unit - 2M Blue (interchangeable with 2M Red and 2M Silver)

Each of the 2M Series cartridges has its own individual sonic expression, and all five models together represent the ensemble of five classic variations:

• 2M Mono SE, 2M Mono and 2M 78 are a true mono cartridges for playing mono vinyl records
• 2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth
• 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details
• 2M Bronze adds even more details and resolution but in a very evenhanded way that pays respect to all elements
• 2M Black is the best of everything, true to the groove with resolution and accurate insight into each recording

The 2M Series is developed in conjunction with the Danish Industrial designer Møller Jensen Design – the same designer who designed the award winning MC Jubilee and Kontrapunkt series. Inspired by the facets of a diamond, whose contours gracefully trace the grooves on a record’s surface, the 2M’s handsome elegance establishes a great combination of form and functionality.

The name 2M was selected from among several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.

Of course the 2M isn’t just another pretty face. It has been engineered to the highest standards and is congruent with Ortofon’s unrelenting commitment to providing the most precise and accurate reproduction possible without coloration.

The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Bronze features:

The 2M Bronze features a Nude Fine Line diamond, which is particularly suited for demanding applications. The slim profile of the Fine Line stylus will track even the highest frequency information, making it a must for discerning listeners. Additionally, its larger footprint ensures reduced distortion and record wear.

The cartridge body is manufactured from Hopelex, a material which ensures high rigidity while eliminating unwanted resonances. The 2M Bronze uses a special upgraded engine, featuring split pole pins with a silver plated copper wire.

Output voltage at 1000 Hz, 5cm/sec. - 5 mV
Channel balance at 1 kHz - 1 dB
Channel separation at 1 kHz - 26 dB
Channel separation at 15 kHz - 15 dB
Frequency response - 20-20.000 + 2 / - 0 dB
Tracking ability at 315Hz at recommended tracking force - 80 µm
Compliance, dynamic, lateral - 22 µm/mN
Stylus type - Nude Fine Line
Stylus tip radius - r/R 8/40 µm
Tracking force range - 1.4-1.7 g (14-17 mN)
Tracking force, recommended - 1.5 g (15 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1.2 kOhm
Internal inductance - 630 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 150-300 pF
Cartridge colour, body/stylus - Black/Bronze
Cartridge weight - 7.2 g
Replacement stylus unit - 2M Bronze (interchangeable with 2M Black and 2M Black LVB 250)

Each of the 2M Series cartridges has its own individual sonic expression, and all five models together represent the ensemble of five classic variations:

• 2M Mono SE, 2M Mono and 2M 78 are a true mono cartridges for playing mono vinyl records
• 2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth
• 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details
• 2M Bronze adds even more details and resolution but in a very evenhanded way that pays respect to all elements
• 2M Black is the best of everything, true to the groove with resolution and accurate insight into each recording

Bona fide precision with the 2M Bronze
To us hi-fi is more than a fancy label. High fidelity is the goal of everything we do. The 2M Bronze is designed to give the music a whole new dimension of precision. Listening to your records with the 2M Bronze is like hearing them for the first time and you get to fall in love with the songs all over. That is what hi-fi means to us and that is what you get with the 2M Bronze.

Features:
The 2M Bronze features a Nude Fine Line diamond, which is particularly suited for demanding applications. The slim profile of the Fine Line stylus will track even the highest frequency information. Additionally, its larger footprint ensures reduced distortion and record wear. The 2M Bronze uses a special upgraded engine, featuring split pole pins with a silver plated copper wire.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Bronze Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5 mV
• Channel balance at 1 kHz - 1 dB
• Channel separation at 1 kHz - 26 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 + 2 / - 0 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 22 µm/mN
• Stylus type - Nude Fine Line
• Stylus tip radius - r/R 8/40 µm
• Tracking force range - 1.4-1.7 g (14-17 mN)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.2 kOhm
• Internal inductance - 630 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Bronze
• Cartridge weight - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M Bronze (interchangeable with 2M Black and 2M Black LVB 250)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze, 2M Black and 2m Black LVB 250
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

With the 2M Premounted, it’s never been easier to experience
The 2M Premounted is a practical and elegant solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm. The quality of the SH-4 headshell is sturdy and rigid, yet the design emphasizes a slim and delicate form factor. The strong, lightweight headshell has an ergonomic design with a long finger lift that is easy to pick up.

Features:
- Premounted on our popular SH-4 Black headshell.
- Easy and direct mount on S-shaped tonearms with universal mount.
- Correct Baerwald alignment with tonearms with universal mount.

The 2M Series is developed in conjunction with the Danish Industrial designer Møller Jensen Design – the same designer who designed the award winning MC Jubilee and Kontrapunkt series. Inspired by the facets of a diamond, whose contours gracefully trace the grooves on a record’s surface, the 2M’s handsome elegance establishes a great combination of form and functionality.

The name 2M was selected from among several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.

Of course the 2M isn’t just another pretty face. It has been engineered to the highest standards and is congruent with Ortofon’s unrelenting commitment to providing the most precise and accurate reproduction possible without coloration.

The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Bronze features:

The 2M Bronze features a Nude Fine Line diamond, which is particularly suited for demanding applications. The slim profile of the Fine Line stylus will track even the highest frequency information, making it a must for discerning listeners. Additionally, its larger footprint ensures reduced distortion and record wear.

The cartridge body is manufactured from Hopelex, a material which ensures high rigidity while eliminating unwanted resonances. The 2M Bronze uses a special upgraded engine, featuring split pole pins with a silver plated copper wire.

Output voltage at 1000 Hz, 5cm/sec. - 5 mV
Channel balance at 1 kHz - 1 dB
Channel separation at 1 kHz - 26 dB
Channel separation at 15 kHz - 15 dB
Frequency response - 20-20.000 + 2 / - 0 dB
Tracking ability at 315Hz at recommended tracking force - 80 µm
Compliance, dynamic, lateral - 22 µm/mN
Stylus type - Nude Fine Line
Stylus tip radius - r/R 8/40 µm
Tracking force range - 1.4-1.7 g (14-17 mN)
Tracking force, recommended - 1.5 g (15 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1.2 kOhm
Internal inductance - 630 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 150-300 pF
Cartridge colour, body/stylus - Black/Bronze
Cartridge weight - 7.2 g
Replacement stylus unit - 2M Bronze (interchangeable with 2M Black and 2M Black LVB 250)

Each of the 2M Series cartridges has its own individual sonic expression, and all five models together represent the ensemble of five classic variations:

• 2M Mono SE, 2M Mono and 2M 78 are a true mono cartridges for playing mono vinyl records
• 2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth
• 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details
• 2M Bronze adds even more details and resolution but in a very evenhanded way that pays respect to all elements
• 2M Black is the best of everything, true to the groove with resolution and accurate insight into each recording

The 2M Series is developed in conjunction with the Danish Industrial designer Møller Jensen Design – the same designer who designed the award winning MC Jubilee and Kontrapunkt series. Inspired by the facets of a diamond, whose contours gracefully trace the grooves on a record’s surface, the 2M’s handsome elegance establishes a great combination of form and functionality.

The name 2M was selected from among several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.

Of course the 2M isn’t just another pretty face. It has been engineered to the highest standards and is congruent with Ortofon’s unrelenting commitment to providing the most precise and accurate reproduction possible without coloration.

The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Red features:

• an improved engine, which provides an increased output of 5.5mV and an optimized sound reproduction and a high level of sonic accuracy

• Nude Elliptical diamond and split pole pins with a copper wire

• The cartridge body is manufactured from Hopelex, which ensures high rigidity while eliminating unwanted resonances.

2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth.

Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
Channel balance at 1 kHz - 1.5 dB
Channel separation at 1 kHz - 22 dB
Channel separation at 15 kHz - 15 dB
Frequency response - 20-20.000 Hz + 3 / - 1 dB
Tracking ability at 315Hz at recommended tracking force - 70 µm
Compliance, dynamic, lateral - 20 µm/mN
Stylus type - Elliptical
Stylus tip radius - r/R 8/18 µm
Tracking force range - 1.6-2.0 g (16-20 mN)
Tracking force, recommended - 1.8 g (18 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1.3 kOhm
Internal inductance - 700 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 150-300 pF
Cartridge colour, body/stylus - Black/Red
2M standard and 2M Verso cartridges weight - 7.2 g
Replacement stylus unit - 2M Red (interchangeable with 2M Blue and 2M Silver)

Each of the 2M Series cartridges has its own individual sonic expression, and all five models together represent the ensemble of five classic variations:

• 2M Mono SE, 2M Mono and 2M 78 are a true mono cartridges for playing mono vinyl records
• 2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth
• 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details
• 2M Bronze adds even more details and resolution but in a very evenhanded way that pays respect to all elements
• 2M Black is the best of everything, true to the groove with resolution and accurate insight into each recording

The 2M Series is developed in conjunction with the Danish Industrial designer Møller Jensen Design – the same designer who designed the award winning MC Jubilee and Kontrapunkt series. Inspired by the facets of a diamond, whose contours gracefully trace the grooves on a record’s surface, the 2M’s handsome elegance establishes a great combination of form and functionality.

The name 2M was selected from among several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.

Of course the 2M isn’t just another pretty face. It has been engineered to the highest standards and is congruent with Ortofon’s unrelenting commitment to providing the most precise and accurate reproduction possible without coloration.

The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Red features:

• an improved engine, which provides an increased output of 5.5mV and an optimized sound reproduction and a high level of sonic accuracy

• Nude Elliptical diamond and split pole pins with a copper wire

• The cartridge body is manufactured from Hopelex, which ensures high rigidity while eliminating unwanted resonances.

2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth.

Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
Channel balance at 1 kHz - 1.5 dB
Channel separation at 1 kHz - 22 dB
Channel separation at 15 kHz - 15 dB
Frequency response - 20-20.000 Hz + 3 / - 1 dB
Tracking ability at 315Hz at recommended tracking force - 70 µm
Compliance, dynamic, lateral - 20 µm/mN
Stylus type - Elliptical
Stylus tip radius - r/R 8/18 µm
Tracking force range - 1.6-2.0 g (16-20 mN)
Tracking force, recommended - 1.8 g (18 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1.3 kOhm
Internal inductance - 700 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 150-300 pF
Cartridge colour, body/stylus - Black/Red
2M standard and 2M Verso cartridges weight - 7.2 g
Replacement stylus unit - 2M Red (interchangeable with 2M Blue and 2M Silver)

Each of the 2M Series cartridges has its own individual sonic expression, and all five models together represent the ensemble of five classic variations:

• 2M Mono SE, 2M Mono and 2M 78 are a true mono cartridges for playing mono vinyl records
• 2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth
• 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details
• 2M Bronze adds even more details and resolution but in a very evenhanded way that pays respect to all elements
• 2M Black is the best of everything, true to the groove with resolution and accurate insight into each recording

2MR: the newest addition to the renowned 2M Series
Ortofon 2MR features a specially designed cartridge housing tailored for turntables and tonearms like Rega matching their requirement for low-form factor cartridges. With its narrow cartridge housing, it seamlessly integrates without a need for modifications or spacers under the tonearm, enabling quick and easy mounting with just two screws. Ortofon 2MR cartridges features unique to Ortofon technologies like: High-performance quad coil motor system with split pole pins, Proprietary Ortofon premium and high-end rubber dampers plus full compatibility with the Ortofon 2M series styli.

Authentic sound reproduction
2MR continues the 2M Series' commitment to authentic sound reproduction.
A high-performance motor system featuring quad coils and split pole pins minimizes eddy current losses, enhancing channel balance and accuracy.
This innovation results in a clean, detailed, and true-to-life sound, faithfully capturing the nuances of your cherished vinyl collection.

More than just a cartridge
2MR cartridge are for those who value an authentic immersive listening experience when listening to their music. 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.
The 2MR maintains the hallmark of interchangeability, allowing you to explore your records in greater depth and detail. The seamless transition between stylus profiles lets you tailor your listening experience, ensuring every note is heard with unparalleled accuracy and emotion. The 2MR series empowers you to explore your records like never before, allowing you to savor every moment of your favorite music.
The 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.

2MR cartridge key features:
• Slimline cartridge body effectively eliminates the need for tonearm spacers, shims or modifications on turntables needing a low form factor cartridge.
• High-performance motor system incorporating unique to Ortofon quad coils with split pole pins, delivering a clean detailed and true-to-life sound.
• 100% compatibility with the 2M styli Ortofon 2MR use the well-known 2M styli.
• Standard half inch mounting quick and easy mounting on the tonearms with just two screws.
• Full range setup 2MR ranges from Mono to Premium: 2MR Red to High-end: 2MR Black LVB 250

Next level authenticity with the 2M Blue
The goal for any cartridge should be to reproduce the sound as close to the artists vision as possible, and the 2M blue takes you further on this journey of authenticity. With the 2M Blue, you get serious about listening to vinyl.

Features:
The 2M Blue features a Nude Elliptical diamond and split pole pins with a copper wire.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

The 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details compared to the 2M Red model.

Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 25 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 2 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Nude Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Blue
• 2MR cartridge weight - 6 g
• 2M and 2M Verso cartridges weight - 7.2 g
• 2M Premounted cartridge weight - 16.7 g

Replacement stylus unit - 2M Blue (interchangeable with 2M Red and 2M Silver)

Stylus lifetime:
with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

2MR: the newest addition to the renowned 2M Series
Ortofon 2MR features a specially designed cartridge housing tailored for turntables and tonearms like Rega matching their requirement for low-form factor cartridges. With its narrow cartridge housing, it seamlessly integrates without a need for modifications or spacers under the tonearm, enabling quick and easy mounting with just two screws. Ortofon 2MR cartridges features unique to Ortofon technologies like: High-performance quad coil motor system with split pole pins, Proprietary Ortofon premium and high-end rubber dampers plus full compatibility with the Ortofon 2M series styli.

Authentic sound reproduction
2MR continues the 2M Series' commitment to authentic sound reproduction.
A high-performance motor system featuring quad coils and split pole pins minimizes eddy current losses, enhancing channel balance and accuracy.
This innovation results in a clean, detailed, and true-to-life sound, faithfully capturing the nuances of your cherished vinyl collection.

More than just a cartridge
2MR cartridge are for those who value an authentic immersive listening experience when listening to their music. 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.
The 2MR maintains the hallmark of interchangeability, allowing you to explore your records in greater depth and detail. The seamless transition between stylus profiles lets you tailor your listening experience, ensuring every note is heard with unparalleled accuracy and emotion. The 2MR series empowers you to explore your records like never before, allowing you to savor every moment of your favorite music.
The 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.

2MR cartridge key features:
• Slimline cartridge body effectively eliminates the need for tonearm spacers, shims or modifications on turntables needing a low form factor cartridge.
• High-performance motor system incorporating unique to Ortofon quad coils with split pole pins, delivering a clean detailed and true-to-life sound.
• 100% compatibility with the 2M styli Ortofon 2MR use the well-known 2M styli.
• Standard half inch mounting quick and easy mounting on the tonearms with just two screws.
• Full range setup 2MR ranges from Mono to Premium: 2MR Red to High-end: 2MR Black LVB 250

Bona fide precision with the 2M Bronze
To us hi-fi is more than a fancy label. High fidelity is the goal of everything we do. The 2M Bronze is designed to give the music a whole new dimension of precision. Listening to your records with the 2M Bronze is like hearing them for the first time and you get to fall in love with the songs all over. That is what hi-fi means to us and that is what you get with the 2M Bronze.

Features:
The 2M Bronze features a Nude Fine Line diamond, which is particularly suited for demanding applications. The slim profile of the Fine Line stylus will track even the highest frequency information. Additionally, its larger footprint ensures reduced distortion and record wear. The 2M Bronze uses a special upgraded engine, featuring split pole pins with a silver plated copper wire.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5 mV
• Channel balance at 1 kHz - 1 dB
• Channel separation at 1 kHz - 26 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 + 2 / - 0 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 22 µm/mN
• Stylus type - Nude Fine Line
• Stylus tip radius - r/R 8/40 µm
• Tracking force range - 1.4-1.7 g (14-17 mN)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.2 kOhm
• Internal inductance - 630 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Bronze
• 2MR cartridge weight - 6 g
• 2M and 2M Verso cartridges weight - 7.2 g
• 2M Premounted cartridge weight - 16.7 g

Replacement stylus unit - 2M Bronze (interchangeable with 2M Black and 2M Black LVB 250)

Stylus lifetime:
with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

2MR: the newest addition to the renowned 2M Series
Ortofon 2MR features a specially designed cartridge housing tailored for turntables and tonearms like Rega matching their requirement for low-form factor cartridges. With its narrow cartridge housing, it seamlessly integrates without a need for modifications or spacers under the tonearm, enabling quick and easy mounting with just two screws. Ortofon 2MR cartridges features unique to Ortofon technologies like: High-performance quad coil motor system with split pole pins, Proprietary Ortofon premium and high-end rubber dampers plus full compatibility with the Ortofon 2M series styli.

Authentic sound reproduction
2MR continues the 2M Series' commitment to authentic sound reproduction.
A high-performance motor system featuring quad coils and split pole pins minimizes eddy current losses, enhancing channel balance and accuracy.
This innovation results in a clean, detailed, and true-to-life sound, faithfully capturing the nuances of your cherished vinyl collection.

More than just a cartridge
2MR cartridge are for those who value an authentic immersive listening experience when listening to their music. 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.
The 2MR maintains the hallmark of interchangeability, allowing you to explore your records in greater depth and detail. The seamless transition between stylus profiles lets you tailor your listening experience, ensuring every note is heard with unparalleled accuracy and emotion. The 2MR series empowers you to explore your records like never before, allowing you to savor every moment of your favorite music.
The 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.

2MR cartridge key features:
• Slimline cartridge body effectively eliminates the need for tonearm spacers, shims or modifications on turntables needing a low form factor cartridge.
• High-performance motor system incorporating unique to Ortofon quad coils with split pole pins, delivering a clean detailed and true-to-life sound.
• 100% compatibility with the 2M styli Ortofon 2MR use the well-known 2M styli.
• Standard half inch mounting quick and easy mounting on the tonearms with just two screws.
• Full range setup 2MR ranges from Mono to Premium: 2MR Red to High-end: 2MR Black LVB 250

Step into the music with the 2M Red
With the 2M Red you will hear the music come to life on its own terms. It is like taking a step into music itself. This is our entry-level cartridge in the series, but what an entry.

Featues:
The 2M Red features a tipped Elliptical diamond and split pole pins with a copper wire.
The engine provides an increased output of 5.5 mV and an optimized sound reproduction and a high level of sonic accuracy.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Red delivers an open, dynamic sound with a slight touch of warmth.

Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 22 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 70 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Red
• 2MR cartridge weight - 6 g
• 2M and 2M Verso cartridges weight - 7.2 g
• 2M Premounted cartridge weight - 16.7 g

Replacement stylus unit - 2M Red (interchangeable with 2M Blue and 2M Silver)

Stylus lifetime:
with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

The best sound quality achievable for traditional vinyl playback
The CLUB boasts the best specifications and best sound, making it an ideal choice for Club DJs in any environment: studio, broadcast or club.
• The CLUB features a Special-Elliptic stylus that allows for detailed sound quality: Special-Elliptic stylus fits better in the groove and therefore has more contact area with the groove itself, extracting more intricate details, than is possible with a spherical diamond.
• The CLUB’s 8 mV output voltage requires less gain from the preamps, providing cleaner sound reproduction and less susceptibility to feedback in live environments.

The CLUB offers an outstanding platform for archival and sampling.

Output voltage at 1000Hz, 5cm/sec. - 8 mV
Channel balance at 1kHz - 1 dB
Channel separation at 1kHz - 25 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 100 μm
Compliance, dynamic lateral - 14 μm/m N
Stylus type - Spherical Elliptical r/R 13/25 μm
Tracking force range - 2 - 4 g
Tracking force recommended - 3 g

Cartridge weight - 18,5 g
Replacement stylus unit - CLUB

Video: https://youtu.be/WZnFkEwAnCo

The best sound quality achievable for traditional vinyl playback
The CLUB boasts the best specifications and best sound, making it an ideal choice for Club DJs in any environment: studio, broadcast or club.
• The CLUB features a Special-Elliptic stylus that allows for detailed sound quality: Special-Elliptic stylus fits better in the groove and therefore has more contact area with the groove itself, extracting more intricate details, than is possible with a spherical diamond.
• The CLUB’s 8 mV output voltage requires less gain from the preamps, providing cleaner sound reproduction and less susceptibility to feedback in live environments.

The CLUB offers an outstanding platform for archival and sampling.

Output voltage at 1000Hz, 5cm/sec. - 8 mV
Channel balance at 1kHz - 1 dB
Channel separation at 1kHz - 25 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 100 μm
Compliance, dynamic lateral - 14 μm/m N
Stylus type - Spherical Elliptical r/R 13/25 μm
Tracking force range - 2 - 4 g
Tracking force recommended - 3 g

Cartridge weight - 18,5 g
Replacement stylus unit - CLUB

• incl. Brush
• incl. Flight Case

Video: https://youtu.be/WZnFkEwAnCo

supplied in Flight case

Concorde DIGITAL is designed to extend the life of timecode vinyl and minimize errors in decoding
• At the same time DIGITAL provides optimal output voltage and sound quality for use with conventional vinyl.
• This optimized 10 mV output voltage maximizes the signal-to-noise ratio of the audio being fed to the software, which results in better interpretation of the timecode signal.
• Furthermore, a decrease in the reproduction of frequencies where vinyl wear & crackle occur helps to minimize errors in the interpretation of the timecode signal and helps timecoded vinyl records last longer.

Output voltage at 1000Hz, 5cm/sec. - 10 mV
Channel balance at 1kHz - 1 dB
Channel separation at 1kHz - 22 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-18.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 100 μm
Compliance, dynamic lateral - 14 μm/m N
Stylus type - Spherical R 18 μm
Tracking force range - 3 - 5 g
Tracking force recommended - 4 g

Cartridge weight - 18,5 g
Replacement stylus unit - DIGITAL

Video: https://youtu.be/nO6b2q2FqQA

Concorde DIGITAL is designed to extend the life of timecode vinyl and minimize errors in decoding
• At the same time DIGITAL provides optimal output voltage and sound quality for use with conventional vinyl.
• This optimized 10 mV output voltage maximizes the signal-to-noise ratio of the audio being fed to the software, which results in better interpretation of the timecode signal.
• Furthermore, a decrease in the reproduction of frequencies where vinyl wear & crackle occur helps to minimize errors in the interpretation of the timecode signal and helps timecoded vinyl records last longer.

Output voltage at 1000Hz, 5cm/sec. - 10 mV
Channel balance at 1kHz - 1 dB
Channel separation at 1kHz - 22 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-18.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 100 μm
Compliance, dynamic lateral - 14 μm/m N
Stylus type - Spherical R 18 μm
Tracking force range - 3 - 5 g
Tracking force recommended - 4 g

Cartridge weight - 18,5 g
Replacement stylus unit - DIGITAL

Video: https://youtu.be/nO6b2q2FqQA

supplied in Flight case

Excellent groove handling
The Concorde DJ is considered the jack-of-all-trades, boasting accurate sound reproduction and excellent groove handling.

• The DJ is great for any style of music.
• It has a spherical stylus and an extremely balanced cantilever that provides outstanding rigidity.
• Not only does the cartridge have a most sufficient tracking ability, it also provides the DJs with the most needed stringency and very low record wear.

All in all: improved tracking, alongside of accurate sound reproduction and an excellent groove handling.

Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel balance at 1kHz - 1 dB
Channel separation at 1kHz - 22 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 100 μm
Compliance, dynamic lateral - 14 μm/m N
Stylus type - Spherical R 18 μm
Tracking force range - 3 - 5 g
Tracking force recommended - 4 g

Cartridge weight - 18,5 g
Replacement stylus unit - DJ

Excellent groove handling
The Concorde DJ is considered the jack-of-all-trades, boasting accurate sound reproduction and excellent groove handling.

• The DJ is great for any style of music.
• It has a spherical stylus and an extremely balanced cantilever that provides outstanding rigidity.
• Not only does the cartridge have a most sufficient tracking ability, it also provides the DJs with the most needed stringency and very low record wear.

All in all: improved tracking, alongside of accurate sound reproduction and an excellent groove handling.

Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel balance at 1kHz - 1 dB
Channel separation at 1kHz - 22 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 100 μm
Compliance, dynamic lateral - 14 μm/m N
Stylus type - Spherical R 18 μm
Tracking force range - 3 - 5 g
Tracking force recommended - 4 g

Cartridge weight - 18,5 g
Replacement stylus unit - DJ

supplied in Flight case

The Concorde Elite is a premium moving magnet cartridge, based on the legacy of the Ortofon Concorde MkII Series. Created with passion, combined with technology and close attention to detail, every feature of the Concorde Elite brings you a limitless experience with the music you love.

We have created a cartridge characteristic of Ortofon’s pioneering approach to design and years of extensive knowledge of reproducing music as it was meant to be heard. Owing to the upgrades of components, the Elite achieves a new level of sound quality not previously found in DJ categorized cartridges.

The Concorde Elite features a new, special-molded stylus body with real gold plating. Encased by the gold is a Nude Elliptical diamond mounted on a rigid Aluminum-Magnesium cantilever. The nude diamond stylus, you normally will find in HiFi cartridges, delivers a sound so powerful and detailed, you will experience a remarkable level of live performance.

The properties of the Rigid 750 µm Aluminum-Magnesium Cantilever, exclusively developed for the Concorde Elite, ensure that the stylus picks up the groove vibrations with a stable and accurate trace performance, and provides the ideal interface between the stylus and armature.

In the armature, you’ll find a Unique Coil System transmitting the diamond’s movements to deliver an optimized output. The engineering of the coil system provides the Elite with a powerful, full-bodied sound of high quality and high output.

To ensure superior tracking performance, a new Rubber Suspension has been developed. The new rubber compound formula has been developed uniquely for the Concorde Elite to attain the desired characteristics for an extraordinary performance of the cartridge.

Output voltage at 1000 Hz, 5cm/sec. - 8,5 mV
Channel balance at 1 kHz - 1 dB
Channel separation at 1 kHz - 25 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3 dB - 20 – 20,000 Hz
Tracking ability at 315Hz - 100 μm
Compliance, dynamic lateral - 13 μm/mN
Stylus type - Nude Elliptical
Stylus tip radius - r/R 8/18 μm
Tracking force range 2.0-4.0 g
Tracking force recommended - 3.0 g
Tracking angle - 20°

Internal impedance, DC resistance - 1.2 kOhm
Internal inductance - 800 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 150-400 pF
Cartridge weight excluding screws - 18.5 g
Cartridge colour (body/stylus) - Black / Gold

The MIX is a general-purpose model for scratch and back-cueing
• Provides great performance and durability. It has a good quality spherical stylus, a solid cantilever, and serves general purposes well.
• It offers both reasonable output, high sound quality and a good tracking ability for virtually any style of music.
• With transparent sound across the spectrum and excellent handling ability, the MIX represents one of the longest running values in DJ cartridges.

Excellent price-to-performance ratio.

Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 20 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 100 μm
Compliance, dynamic lateral - 14 μm/m N
Stylus type - Spherical R 18 μm
Tracking force range - 2 - 4 g
Tracking force recommended - 3 g

Cartridge weight - 18,5 g
Replacement stylus unit - MIX

Video: https://youtu.be/4nSIq_jTUKQ

The MIX is a general-purpose model for scratch and back-cueing
• Provides great performance and durability. It has a good quality spherical stylus, a solid cantilever, and serves general purposes well.
• It offers both reasonable output, high sound quality and a good tracking ability for virtually any style of music.
• With transparent sound across the spectrum and excellent handling ability, the MIX represents one of the longest running values in DJ cartridges.

Excellent price-to-performance ratio.

Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 20 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 100 μm
Compliance, dynamic lateral - 14 μm/m N
Stylus type - Spherical R 18 μm
Tracking force range - 2 - 4 g
Tracking force recommended - 3 g

Cartridge weight - 18,5 g
Replacement stylus unit - MIX

Video: https://youtu.be/4nSIq_jTUKQ

supplied in Flight case

New levels of performance
The Concorde Scratch allows turntablist and scratching DJs to achieve new levels of performance with an unprecedented tracking ability and extra high output.
• The SCRATCH is intended especially for scratching and back-cueing. The SCRATCH uses spherical styli, as they preserve more of the groove over backcueing and scratching.
• For DJs that require increased tracking ability, the SCRATCH is up to the task. The Scratch has a supreme ability to trace the grooves of the records and it is tailored specifically for scratch.
• Due to its very high output 10 mV, it is perfect for scratch of all music with deep bass frequences. With solid bass reproduction and extended highs, the SCRATCH is great for any style, providing energetic sound. Maximum scratch performance guaranteed!

Output voltage at 1000Hz, 5cm/sec. - 10 mV
Channel balance at 1kHz - 1 dB
Channel separation at 1kHz - 22 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-18.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 120 μm
Compliance, dynamic lateral - 14 μm/m N
Stylus type - Spherical R 18 μm
Tracking force range - 3 - 5 g
Tracking force recommended - 4 g

Cartridge weight - 18,5 g
Replacement stylus unit - SCRATCH

Video: https://youtu.be/hPQNkhzZuBQ

New levels of performance
The Concorde Scratch allows turntablist and scratching DJs to achieve new levels of performance with an unprecedented tracking ability and extra high output.
• The SCRATCH is intended especially for scratching and back-cueing. The SCRATCH uses spherical styli, as they preserve more of the groove over backcueing and scratching.
• For DJs that require increased tracking ability, the SCRATCH is up to the task. The Scratch has a supreme ability to trace the grooves of the records and it is tailored specifically for scratch.
• Due to its very high output 10 mV, it is perfect for scratch of all music with deep bass frequences. With solid bass reproduction and extended highs, the SCRATCH is great for any style, providing energetic sound. Maximum scratch performance guaranteed!

Output voltage at 1000Hz, 5cm/sec. - 10 mV
Channel balance at 1kHz - 1 dB
Channel separation at 1kHz - 22 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-18.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 120 μm
Compliance, dynamic lateral - 14 μm/m N
Stylus type - Spherical R 18 μm
Tracking force range - 3 - 5 g
Tracking force recommended - 4 g

Cartridge weight - 18,5 g
Replacement stylus unit - SCRATCH

Video: https://youtu.be/hPQNkhzZuBQ

supplied in Flight case

Introducing Concorde Music
Developed by music lovers, for music lovers, the Concorde Music cartridges blend premium performance with an iconic design.
Concorde Music, not just a cartridge, but a dedication to the profound impact music has on our lives, turning every listening session
into a captivating journey.

Possibly the world’s most iconic cartridge design
Building upon a rich legacy which began when we launched the original Concorde, the Concorde Music holds a storied history as
one of the most famous cartridges in the world of audio. Originally developed as a solution to the challenge of easy mounting on a
tonearm without screws or wires, the Concorde's unique design earned the Danish Industrial Design Award and became an icon in
the audio industry.

Features:
• Diamond: Each Concorde Music stylus features a diamond polished to the highest standards of the industry. Ranging from
a bonded Elliptical diamond on Concorde Music Red, to a Nude Shibata diamond on Concorde Music Black LVB 250.
• Cantilever: All Concorde Music models have a premium or high-end cantilever. The cantilever material is either aluminium
or boron for the best possible transmission of the vinyl record groove modulations picked up by the diamonds.
• Suspension: Exclusive Ortofon rubber compounds are used for the stylus suspensions, all carefully produced at the in_x0002_house own rubber production, and developed by the research and engineering team at Ortofon for brilliant performance.
• Coil system: Silver-pated oxygen free copper is chosen for the quad-coil system together with four Ortofon split pole pins
delivering a 6 mV output of dynamic, lifelike sound with an exceptional clarity and fidelity, capturing every detail.
• Upgradeability: All Concorde Music styli are compatible with all Concorde Music cartridges. An upgrade path is possible
through the entire series of Concorde Music cartridges, enabling upgrades from Concorde Music Red to Black LVB 250.
• Tool-free installation: Installing a Concorde Music cartridge on a turntable is easy and straightforward, no tools required
making it hassle free and convenient for all users.

It is all about the music
Concorde Music stands as an icon of design and musical dedication, inviting everyone to elevate their journey with the level of
accuracy in sound which has become characteristic for every Ortofon cartridge. Tailored for music lovers, incorporating a
straightforward installation, premium sound, and a timeless design. Concorde Music stands for a commitment to musicality.

Unique in-house rubber production a crucially important and vital part of a phono cartridge overall performance is the stylus
rubber suspension. Ortofon develops exclusive rubber compounds and produce the rubber suspensions and dampers in-house.

Ortofon quad-coil generating system with split pole pins in Concorde Music results in an exceptional channel balance and channel
separation, delivering a precise and dynamic sound image.

Ortofon, we love music!

Introducing Concorde Music
Developed by music lovers, for music lovers, the Concorde Music cartridges blend premium performance with an iconic design.
Concorde Music, not just a cartridge, but a dedication to the profound impact music has on our lives, turning every listening session
into a captivating journey.

Possibly the world’s most iconic cartridge design
Building upon a rich legacy which began when we launched the original Concorde, the Concorde Music holds a storied history as
one of the most famous cartridges in the world of audio. Originally developed as a solution to the challenge of easy mounting on a
tonearm without screws or wires, the Concorde's unique design earned the Danish Industrial Design Award and became an icon in
the audio industry.

Features:
• Diamond: Each Concorde Music stylus features a diamond polished to the highest standards of the industry. Ranging from
a bonded Elliptical diamond on Concorde Music Red, to a Nude Shibata diamond on Concorde Music Black LVB 250.
• Cantilever: All Concorde Music models have a premium or high-end cantilever. The cantilever material is either aluminium
or boron for the best possible transmission of the vinyl record groove modulations picked up by the diamonds.
• Suspension: Exclusive Ortofon rubber compounds are used for the stylus suspensions, all carefully produced at the in_x0002_house own rubber production, and developed by the research and engineering team at Ortofon for brilliant performance.
• Coil system: Silver-pated oxygen free copper is chosen for the quad-coil system together with four Ortofon split pole pins
delivering a 6 mV output of dynamic, lifelike sound with an exceptional clarity and fidelity, capturing every detail.
• Upgradeability: All Concorde Music styli are compatible with all Concorde Music cartridges. An upgrade path is possible
through the entire series of Concorde Music cartridges, enabling upgrades from Concorde Music Red to Black LVB 250.
• Tool-free installation: Installing a Concorde Music cartridge on a turntable is easy and straightforward, no tools required
making it hassle free and convenient for all users.

It is all about the music
Concorde Music stands as an icon of design and musical dedication, inviting everyone to elevate their journey with the level of
accuracy in sound which has become characteristic for every Ortofon cartridge. Tailored for music lovers, incorporating a
straightforward installation, premium sound, and a timeless design. Concorde Music stands for a commitment to musicality.

Unique in-house rubber production a crucially important and vital part of a phono cartridge overall performance is the stylus
rubber suspension. Ortofon develops exclusive rubber compounds and produce the rubber suspensions and dampers in-house.

Ortofon quad-coil generating system with split pole pins in Concorde Music results in an exceptional channel balance and channel
separation, delivering a precise and dynamic sound image.

Ortofon, we love music!

Introducing Concorde Music
Developed by music lovers, for music lovers, the Concorde Music cartridges blend premium performance with an iconic design.
Concorde Music, not just a cartridge, but a dedication to the profound impact music has on our lives, turning every listening session
into a captivating journey.

Possibly the world’s most iconic cartridge design
Building upon a rich legacy which began when we launched the original Concorde, the Concorde Music holds a storied history as
one of the most famous cartridges in the world of audio. Originally developed as a solution to the challenge of easy mounting on a
tonearm without screws or wires, the Concorde's unique design earned the Danish Industrial Design Award and became an icon in
the audio industry.

Features:
• Diamond: Each Concorde Music stylus features a diamond polished to the highest standards of the industry. Ranging from
a bonded Elliptical diamond on Concorde Music Red, to a Nude Shibata diamond on Concorde Music Black LVB 250.
• Cantilever: All Concorde Music models have a premium or high-end cantilever. The cantilever material is either aluminium
or boron for the best possible transmission of the vinyl record groove modulations picked up by the diamonds.
• Suspension: Exclusive Ortofon rubber compounds are used for the stylus suspensions, all carefully produced at the in_x0002_house own rubber production, and developed by the research and engineering team at Ortofon for brilliant performance.
• Coil system: Silver-pated oxygen free copper is chosen for the quad-coil system together with four Ortofon split pole pins
delivering a 6 mV output of dynamic, lifelike sound with an exceptional clarity and fidelity, capturing every detail.
• Upgradeability: All Concorde Music styli are compatible with all Concorde Music cartridges. An upgrade path is possible
through the entire series of Concorde Music cartridges, enabling upgrades from Concorde Music Red to Black LVB 250.
• Tool-free installation: Installing a Concorde Music cartridge on a turntable is easy and straightforward, no tools required
making it hassle free and convenient for all users.

It is all about the music
Concorde Music stands as an icon of design and musical dedication, inviting everyone to elevate their journey with the level of
accuracy in sound which has become characteristic for every Ortofon cartridge. Tailored for music lovers, incorporating a
straightforward installation, premium sound, and a timeless design. Concorde Music stands for a commitment to musicality.

Unique in-house rubber production a crucially important and vital part of a phono cartridge overall performance is the stylus
rubber suspension. Ortofon develops exclusive rubber compounds and produce the rubber suspensions and dampers in-house.

Ortofon quad-coil generating system with split pole pins in Concorde Music results in an exceptional channel balance and channel
separation, delivering a precise and dynamic sound image.

Ortofon, we love music!

Enter the Exclusive world of Ortofon’s famous moving coil sound!
The Quintet Red is a perfect introduction to the world of Ortofon moving coils.
It features an Elliptical diamond which is cut and polished to Ortofon’s standards.

This entry-level MC cartridge has very high price-to-performance ratio and is a perfect all-rounder for the newcomers to the world of Moving Coil cartridges.

MC Quintet Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth.

The ST-7 transformer is a perfect match for the MC Quintet Red cartridge.

LH-4000 headshell is specially recommended for MC Quintet cartridges series.

MC Quintet Red Technical data:
• Output voltage at 1 kHz 5 cm/sec - 0.5 mV
• Channel balance - < 1.5 dB
• Channel separation at 1 kHz - > 21 dB
• Channel separation at 15 kHz - > 14 dB
• Frequency response 20-20.000 Hz - +/-2.5 dB
• Tracking ability at 315 Hz at recommended tracking force *) - 65 μm
• Compliance, dynamic, lateral - 15 μm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 μm
• Tracking force range - 2.1-2.5 g (21-25 mN)
• Tracking force recommended - 2.3 g (23 mN)
• Tracking angle - 20º
• Internal impedance, DC resistance - 7 Ohm
• Recommended load impedance - >20 Ohm
• Cartridge body material - ABS/Aluminium
• Coil wire material - Copper
• Cartridge colour - Red
• Cartridge weight - 9 g
*) Typical value

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for Quintet cartridge.

Ease of use
Top-mounting of the Quintet cartridges is easy and secure using the screws supplied. The aluminuim frame has threaded mounting holes and is fitted easily with the 5mm or 7mm screws depending on the thickness of the headshell.

The Quintet series’ right angles, straight lines, stylus visibility and ample distance between the record surface and the cartridge’s bottom will make it easy to mount and align the cartridge and tonearm correctly. The Quintet Series gives excellent results with most common tonearms.

Optimal fit and sound reproduction
If your tonearm has a standard headshell or a cartridge mount, then step up to optimal sound reproduction with OM’s. A glance at anyone of these cartridges will reveal Ortofon's answer to perfect tonearm matching. Ingeniously tucked into the top of the mounting bracket is a tiny, removable weight-plate.

If your tonearm is an standard tonearm, just leave the weight-plate. If your tonearm is one of the low mass types, then simply remove the weight. The mass of your OM cartridge is now a mere 2.5g.

OM 5E features Elliptical stylus that provides balanced and distortion-free playback. Elliptical diamonds are able to follow the groove oscillations more accurately than spherical diamonds due to their contoured shape. This results in better tracking and less distortion.

• OM 5E Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4 mV
• Channel balance at 1 kHz - 2 dB
• Channel separation at 1 kHz - 22 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 3 / -3
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17.5 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 750 Ohm
• Internal inductance - 450 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 200-500 pF
• Cartridge colour, body/stylus - Black/Black
• Cartridge weight incl. extra weight - 5 g
• Cartridge weight excl. extra weight - 2.5 g
• Replacement stylus unit - Stylus 5E
*) Typical value

Styli types and interchangeability
By adopting a wide range of replacement styli, the OM 5 Series can provide an optimum match for your home system, application and budget.
In the development of OM cartridges, a major objective was to provide the music lover with the opportunity to optimize sound reproduction without having to replace the entire cartridge. Instead of being merely intended for replacement purposes following wear or damage, the OM 5 Series allows you to step up to better sound by simply upgrading the stylus. Depending on your preference, styli for the OM 5 Series are easily interchanged and include: styli 3E, 5E, 10, 20, 30, 40 & 78 and D 25 M.

The OM 5S is a moving magnet cartridge for general purpose application
If your tonearm has a standard headshell or a cartridge mount, then step up to optimal sound reproduction with OM’s. A glance at anyone of these cartridges will reveal Ortofon's answer to perfect tonearm matching. Ingeniously tucked into the top of the mounting bracket is a tiny, removable weight-plate.

If your tonearm is an standard tonearm, just leave the weight-plate. If your tonearm is one of the low mass types, then simply remove the weight. The mass of your OM cartridge is now a mere 2.5 g.

The OM 5S features Spherical stylus, robust and economic solution for play back of vinyl records.

For more than 50 years, Ortofon has been designing and manufacturing Moving Magnet cartridges. Along with our well-regarded Moving Coil cartridges, Moving Magnet models have established a good reputation among music lovers and Hi-Fi enthusiasts the world over.

The new Ortofon OM 5 series encompasses three basic cartridges: OM 5S, OM 5E and Super OM 5E.
• The series is the lowest-mass range of moving magnet cartridges offered by Ortofon.
• The OM cartridges bodies have been designed to provide easy mounting and alignment on both top mount and bottom mount headshells.
• The OM 5 Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

OM 5S Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4.5 mV
• Channel balance at 1 kHz - 2 dB
• Channel separation at 1 kHz - 20 dB
• Channel separation at 15 kHz - 12 dB
• Frequency response - 20-22.000 Hz
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Spherical
• Stylus tip radius - R 18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17.5 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 750 Ohm
• Internal inductance - 450 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 200-500 pF
• Cartridge colour, body/stylus - Black/Black
• Cartridge weight incl. extra weight - 5 g
• Cartridge weight excl. extra weight - 2.5 g
• Replacement stylus unit - Stylus 5S
*) Typical value

Styli types and interchangeability
By adopting a wide range of replacement styli, the OM 5 Series can provide an optimum match for your home system, application and budget.
In the development of OM cartridges, a major objective was to provide the music lover with the opportunity to optimize sound reproduction without having to replace the entire cartridge. Instead of being merely intended for replacement purposes following wear or damage, the OM 5 Series allows you to step up to better sound by simply upgrading the stylus. Depending on your preference, styli for the OM 5 Series are easily interchanged and include: styli 3E, 5E, 10, 20, 30, 40 & 78 and D 25 M.

OM Pro S pre-mounted on SH-4 Black
The OM Pro S on the SH-4 Black headshell is a practical and convenient solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm.

Features:
• Universal mount fitting a wide range of S-shaped tonearms
• Correct Baerwald alignment with the major part of tonearms with universal mount
• Spherical stylus minimizes scratching
• Solid cantilever can survive hectic activity at the turntable

The OM Pro S is a consistent performer and a fine all-arounder!

OM Pro S technical data
Stylus Type Spherical
Tracking Force 4.0 g (40 mN)
Output Voltage 5 mV
Frequency Range 20-18.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 5 mV
Channel balance at 1kHz - 2 dB
Channel separation at 1kHz - 20 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-18.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 70 μm
Compliance, dynamic lateral - 7 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm
Tracking force range - 3 - 5 g
Tracking force recommended - 4 g
Tracking angle - 20°

Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
OM cartridge weight - 5,0 g
OM pre-mounted on SH-4 weight incl. screws - 14,5 g
Replacement stylus unit - Pro S

OM Q.Bert for scratch and back-cueing
• High tracking ability, unsurpassed handling
• Ultra high output!
• Low wear characteristics that literally put it in a class of its own

Turntablists and mix DJs alike will appreciate the strong output of this cartridge, coupled with unrivaled tracking ability and sonic characteristics. The Q.Bert features a more subdued high end, which helps to minimize surface noise from worn vinyl, and an accentuated mid-range to help bring scratching to the front of the sound stage.

The Q-Bert has a supreme ability to trace the grooves of your records and it is tailored specifically for scratch. Due to its enomous output, it is perfect for scratch of all music with deep bass frequences.

Q.Bert Technical Data
Stylus Type Spherical
Tracking Force 3.0 g
Output Voltage 11 mV
Frequency Range 20-18.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 11 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 22 dB
Frequency range at -3dB - 20-18.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 90 μm
Compliance, dynamic lateral - 12 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm
Tracking force range - 2 - 4 g
Tracking force recommended - 3 g

Tracking angle - 20°
Internal impedance, DC resistance - 1.680 Ohm
Internal inductance - 920 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-400 pF
OM cartridge weight incl. extra weight - 5 g
Replacement stylus unit - Q.Bert

OM Q.Bert pre-mounted on SH-4 Black headshell
The OM Q.Bert on the SH-4 Black headshell is a practical and convenient solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm.

Features:
• Universal mount fitting a wide range of S-shaped tonearms
• Ultra high output
• Low wear characteristics

Tailored specifically for scratch, the OM Q.Bert provides unrivaled tracking ability and sonic characteristics.

Technical Data:
Stylus Type Spherical
Tracking Force 3.0 g
Output Voltage 11 mV
Frequency Range 20-18.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 11 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 22 dB
Frequency range at -3dB - 20-18.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 90 μm
Compliance, dynamic lateral - 12 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm
Tracking force range - 2 - 4 g
Tracking force recommended - 3 g

Tracking angle - 20°
Internal impedance, DC resistance - 1.680 Ohm
Internal inductance - 920 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-400 pF
OM cartridge weight incl. extra weight - 5 g
Replacement stylus unit - Q.Bert

OM Scratch White pre-mounted on SH-4 Blue headshell
The OM Scratch White on the SH-4 Black headshell is a practical and convenient solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm.

Features:
• Universal mount fitting a wide range of S-shaped tonearms
• Correct Baerwald alignment with the major part of tonearms with universal mount
• Spherical stylus minimizes scratching
• Increased tracking ability
• Reinforced rubber suspension

High output and maximum scratch performance guaranteed!

OM Scratch White technical data
Stylus Type Spherical
Tracking Force 4.0 g (40 mN)
Output Voltage 7 mV
Frequency Range 20-15.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 7 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 25 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Frequency response - 20-15.000 Hz 3dB/-2dB
Tracking ability at 315 Hz at recommmended tracking force - 80 μm
Compliance, dynamic lateral - 6 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm
Tracking force range - 3,0-5,0 g (30-50 mN)
Tracking force recommended - 4,0 g (40 mN)
Tracking angle - 20°

Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
OM cartridge weight - 5 g
OM pre-mounted on SH-4 weight incl. screws - 14,5 g

Replacement stylus unit - Scratch White

The Super OM 5E major improvements:
1. By means of computer simulations it has been possible to define the natural pivot point of the system with unprecedented accuracy while achieving an optimum oscillation balance. The result: improved linearity, higher channel separation and reduced distortion.

2. OM Super cartridges models have split pole PINs which reduces magnetic losses at the treble end. This technology extends the frequency range and improves phase linearity.

3. OM Super 5 cartridge body is manufactured from a Noryl (plastic & glass compound) which ensures high rigidity and freedom from resonances.

Optimal fit and sound reproduction
If your tonearm has a standard headshell or a cartridge mount, then step up to optimal sound reproduction with OM’s. A glance at anyone of these cartridges will reveal Ortofon's answer to perfect tonearm matching. Ingeniously tucked into the top of the mounting bracket is a tiny, removable weight-plate.

If your tonearm is an standard tonearm, just leave the weight-plate. If your tonearm is one of the low mass types, then simply remove the weight. The mass of your OM cartridge is now a mere 2.5g.

Super OM 5E features Elliptical stylus that provides balanced and distortion-free playback. Elliptical diamonds are able to follow the groove oscillations more accurately than spherical diamonds due to their contoured shape. This results in better tracking and less distortion.

Super OM 5 Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 22 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 3 / -3
• Tracking ability at 315Hz at recommended tracking force - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17.5 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1 kOhm
• Internal inductance - 580 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 200-500 pF
• Cartridge colour, body/stylus - Black/Black
• Cartridge weight incl. extra weight - 5 g
• Cartridge weight excl. extra weight - 2.5 g
• Replacement stylus unit - Stylus 5 E, Stylus 10

Styli types and interchangeability
The OM 5s features a Spherical diamond. Spherical diamonds are the simplest and most robust diamonds. The OM 5E and Super OM 5E feature an Elliptical diamond.

In the development of OM cartridges, a major objective was to provide the music lover with the opportunity to optimize sound reproduction without having to replace the entire cartridge. Instead of being merely intended for replacement purposes following wear or damage, the OM 5 Series allows you to step up to better sound by simply upgrading the stylus.

Depending on your preference, styli for the OM 5 Series are easily interchanged and include: styli 3E, 5E, 10, 20, 30, 40 & 78 and D 25 M.

The new Ortofon OM 5 series encompasses three basic cartridges: OM 5S, OM 5E and Super OM 5E.
• The series is the lowest-mass range of moving magnet cartridges offered by Ortofon.
• The OM cartridges bodies have been designed to provide easy mounting and alignment on both top mount and bottom mount headshells.
• The OM 5 Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

In ViNyL we trust
Even before the launch of the Concorde MkII, we have always studied the feedback of our customers and how they utilize our products.

Skilled DJs demand specialized tools that can help them push their creativity to the edge – consistently testing the boundaries in the realm of performance.

Understanding this and reflecting our extensive experience in industrial design and technological know-how, we present the new Ortofon VNL cartridge – a model tailored uniquely to the unrelenting demands of modern turntablists and portablists.

Contains 1x Stylus VNL II!

The new VNL features and improvements
• Extra resistance to hardcore scratching and back spinning
• High tracking performance for both DVS usage and real vinyl
• Optimal balance of output and of sound quality

Technological improvements have been applied for the benefits of all users:
- Ultrasonic welding of the components ensures high rigidity and freedom from resonances.
- Robotic assembly of stylus assembly offers high precision and uniformity of industrial production.

DJs can easily identify which stylus type best suits their individual DJ style and enables their absolute best performance capability.

VNL technical data

Stylus Type: Sperical
Tracking Force: 4,0 g
Output Voltage: 6mV
Frequency Range: 20-20.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel separation at 1kHz - 20 dB
Frequency response 20 Hz - 20 kHz -2/+4 dB
Tracking ability at 315 Hz at recommmended tracking force:

VNL I 100 μm
VNL II 90 μm
VNL III 90 μm
Compliance, dynamic lateral:

VNL I 16 μm/m N
VNL II 15 μm/m N
VNL III 14 μm/m N

Tracking force range - 3 - 5 g
Tracking force recommended - 4 g
Antiskating - for best backcueing performance use “0”
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Cartridge weight - 6,5 g
Replacement stylus units: VNL I, VNL II, VNL III

Exclusive features
The VNL features a spherical stylus which is perfect for tough groove handling. Furthermore, it reduces record wear when scratching and back-cueing to an absolute minimum.

The broad stance of the VNL features solid and robust design elements characteristic to Ortofon, with colors meticulously selected to emphasize sturdiness and DJ aesthetics: the cartridge body has been designed to provide easy mounting and alignment on a variety of headshells.

The VNL provides excellent compatibility when used in an assortment of playback systems, ensuring it stays in the groove under the most demanding conditions.

VNL Userguide: https://www.ortofon.com/media/151234/5-800161-12_vnl_userguide_08_20_web.pdf

Get ready to Plug’n Play

Designed to fit any standard DJ turntable. Features high quality tonearm terminal connections.

Ortofon VNL cartridge – a model tailored uniquely to the unrelenting demands of modern
turntablists and portablists.
The plug'n play solution has become an expected and necessary asset for the user, and
with the new VNL Premounted, it’s not getting easier!
The VNL has been paired with our popular black SH-4 Headshell, which securely frames
the VNL cartridge to deliver its absolute best. The VNL Premounted fits any standard DJ
turntable and tonearm and features high quality tonearm terminal connections. We've
created the perfect kit, where you'll have the high standard of the VNL matched with our
favorite headshell to deliver superb convenience and great value.

Just the stylus VNL II is product content!

Features:
• Mounted on Ortofon SH-4 Black headshell with universal mount.
• Extra resistance to hardcore scratching and back spinning
• High tracking performance for both DVS usage and real vinyl
• Optimal balance of output and of sound quality

Technological improvements have been applied for the benefits of all users:
- Ultrasonic welding of the components ensures high rigidity and freedom from resonances.
- Robotic assembly of stylus assembly offers high precision and uniformity of industrial production.

VNL II compliance, dynamic lateral 15 μm/m N - Rigid

DJs can easily identify which stylus type best suits their individual DJ style and enables their absolute best performance capability.

VNL technical data:
• Stylus Type: Sperical
• Tracking Force: 4,0 g
• Output Voltage: 6mV
• Frequency Range: 20-20.000 Hz
• Output voltage at 1000Hz, 5cm/sec. - 6 mV
• Channel separation at 1kHz - 20 dB
• Frequency response 20 Hz - 20 kHz -2/+4 dB

• Tracking ability at 315 Hz at recommmended tracking force:

VNL II 90 μm

VNL II 15 μm/m N

• Tracking force range - 3 - 5 g
• Tracking force recommended - 4 g
• Antiskating - for best backcueing performance use “0”
• Internal impedance, DC resistance - 750 Ohm
• Internal inductance - 450 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 200-600 pF
• Cartridge weight - 6,5 g

Exclusive features
The VNL features a spherical stylus which is perfect for tough groove handling. Furthermore, it reduces record wear when scratching and back-cueing to an absolute minimum.

The broad stance of the VNL features solid and robust design elements characteristic to Ortofon, with colors meticulously selected to emphasize sturdiness and DJ aesthetics: the cartridge body has been designed to provide easy mounting and alignment on a variety of headshells.

The VNL provides excellent compatibility when used in an assortment of playback systems, ensuring it stays in the groove under the most demanding conditions.

VNL Userguide: https://www.ortofon.com/media/151234/5-800161-12_vnl_userguide_08_20_web.pdf

Audiophile MM Cartridge

Lively & robust with a high dynamic range

Intensive research, development and listening tests have been necessary to gain the the desired sound from the new Pick it PRO.

THE DIFFERENCE IN SOUND
Cartridges are electromechanical transducers, where mechanical energy is transformed into an electrical signal. The real difference in sound happens here. The colour and life of the music come from the cartridge.
You cannot judge the cartridge by looking at just one specific part. Experience and the art of fine-tuning make a cartridge unique and special. The perfect combination of components is the key to achieve the great charismatic sound of the Pick it PRO.

Technical Specifications:
• Cartridge principle: MM (Moving-Magnet)
• Output voltage at 1 kHz: 4 mV
• Channel separation at 1 kHz: 22 dB
• Tracking ability at 315Hz: 70 μm
• Frequency response: 20 - 20 000 Hz +/- 2dB
• Stylus type: Elliptical
• Stylus tip radius: r/R 8/18 μm
• Tracking force, range: 1,8 - 2,2 g (mN)
• Tracking force, recommended: 2,0 g (mN)
• Tracking angle: 20°
• Internal impedance, DC resistance: 750 Ohm
• Internal inductance: 450mH
• Recommended load resistance: 47kOhm
• Recommended load capacitance: 150-300pF
• Cartriddge weight: 7,2 g

MM phono cartridge for turntables

Beautiful design and superior sound!

The Pro-Ject Pick it S2 MM is manufactured by the cartridge experts at Ortofon and voiced by the design team at Pro-Ject. It is equipped with a special elliptical stylus tip. It provides detailed sound reproduction and expansive imaging. It is a no-nonsense performer with fascinating musical resources. Attached to a strong cantilever, used in DJ cartridges, this cartridge will not just sound great, it is also very strong.
The cartridge is made from a unique combination of technologies. Among others Ortofon‘s well known split pole pins. This enables it to have a flat frequency response, which compares with MC cartridges. The superior treble output provides a dynamic and warm sound.
Inspired by the diamond found on the stylus, the Pick it S2 MM is a beautiful design featuring a new and unique semi-transparent grey color. It goes perfectly with most Pro-Ject record players.

Features:
• Moving Magnet principle
• Split pole pins enables frequency responses that compares very well to MC cartridges
• Strong cantilever based in high-end DJ cantilevers
• Suitable for low to medium tonearm masses
• 1/2 inch mounting standard
• High trackability
• Pick it S2 MM should be connected to phono MM inputs
• As with most MM cartridges, stylus may be exchanged

Technical Specifications:
• Weight: 7.2 g
• Stylus type: elliptical
• Frequency response: 20 - 20.000 Hz
• Output voltage: 7 mV
• Recommended tracking force: 1,8 g (mN)
• Trackability (315 Hz, lateral): 70 µm
• Recommended load capacitance: 150 - 300 pF
• Recommended load resistance: 47 kΩ