Cartridges & Styluses 59 Items

The Reloop SPIN cartridge system is suitable for scratching, due to the spherical stylus, and is ideally suited for the portable playback of records. With a high tracking ability, the cartridge always stays in the record groove and does not jump, even during fast manoeuvres. In addition, the stylus has a positive effect on vinyl wear.

FEATURES
• Optimized for portable record playback
• Suitable for scratching due to high tracking ability
• Spherical stylus
• Very low vinyl wearout

TECHNICAL DATA
• Frequency range: 100 Hz - 10 kHz
• Output voltage (3.54 cm/s): 180 - 360 mV
• Tracking force range: 4 - 6 g
• Recommended tracking force: 5 g
• Weight: 1.8 g (+/- 0.5 g)

Styli protection caps, pair

OM Q.Bert for scratch and back-cueing
• High tracking ability, unsurpassed handling
• Ultra high output!
• Low wear characteristics that literally put it in a class of its own

Turntablists and mix DJs alike will appreciate the strong output of this cartridge, coupled with unrivaled tracking ability and sonic characteristics. The Q.Bert features a more subdued high end, which helps to minimize surface noise from worn vinyl, and an accentuated mid-range to help bring scratching to the front of the sound stage.

The Q-Bert has a supreme ability to trace the grooves of your records and it is tailored specifically for scratch. Due to its enomous output, it is perfect for scratch of all music with deep bass frequences.

Q.Bert Technical Data
Stylus Type Spherical
Tracking Force 3.0 g
Output Voltage 11 mV
Frequency Range 20-18.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 11 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 22 dB
Frequency range at -3dB - 20-18.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 90 μm
Compliance, dynamic lateral - 12 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm
Tracking force range - 2 - 4 g
Tracking force recommended - 3 g

Tracking angle - 20°
Internal impedance, DC resistance - 1.680 Ohm
Internal inductance - 920 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-400 pF
OM cartridge weight incl. extra weight - 5 g
Replacement stylus unit - Q.Bert

AT-VMN95C
VM95 SERIES CONICAL REPLACEMENT STYLUS
Aluminium cantilever
Conical stylus
Bonded Round Shank

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

CONICAL BONDED STYLUS
The benefit of conical styli, even if the cartridge is "lean", is the ball surface of the stylus touches the groove of vinyl records precisely.

Electronic stylus balance

The Measure it E Stylus Tracking Force Gauge is a highly accurate electronic balance that is designed for measuring stylus tracking forces up to 5.0 grams in 0.002 gram increments. Each Measure it E can easily be calibrated using the supplied calibration weight and by pushing a button. Whenever in doubt about the actual amount of pressure on the diamond tip the 4 digit display of this smart tool will help. Armed with precise information about tracking force, your stylus tip wear can be significantly reduced.

Scope of delivery:
• stylus balance
• calibration weight (5 g)
• 2x LR43 (AG12) button cell batteries + 2 pieces as backup
• protection pouch for the meter
• user guide

Features:
• 4 digit LCD display with backlight
• 4 weighing modes
• Wide capacity 0 - 5g
• Calibration weight
• Precision data readouts with low variance
• Auto calibration function
• Auto power off after 30 seconds
• Low power consumption
• Button cell batteries included

Technical Specifications:
• Capacity: 0 - 5g
• Variance: ±0,002g
• Weighting modes: gram (1g = 10mN), ounce (oz), pennyweight (dwt) & carat (ct)
• Display: 4 digit LCD with backlight
• Calibration: auto calibration using a 5g weight
• Auto off: 30 seconds off
• Replacement battery: 2 x LR43 (AG12) button cells, 1,5V
• Operating temperature: +10 - +30° C (50 - 86 degrees Fahrenheit)
• Dimensions (W x H x D): 96 x 21 x 43mm
• Weight: 49g

Replacement stylus for Nagaoka MP-110.

To exchange the needle of the MP 110, simply pull off the needle carrier of the system and replace it with the JN-P 110.

Hear the vivid sound experience that music playback offers with Nagaoka's MP-110 tonearm. Especially in the high-frequency range, the elliptical needle cut ensures better detail resolution. This creates a live atmosphere while listening, which is otherwise known from concerts.

TECHNICAL SPECIFICATIONS:
• Principle: MI - High Output (for the MM input)
• Weight: 6.5g
• Height: 18mm
• Needle cut: Elliptical 0.4x0.7
• Cantilever: aluminum
• Frequency response: 20 - 20,000 Hz
• Output Voltage (1kHz, 5cm/sec): 5.0mV
• Channel Separation (1kHz): >23dB
• Channel balance (1kHz): < 1.5 dB
• Needle compliance: 19 µm/mN
• Recommended tracking force: 18 mN (15-20 mN)
• Recommended termination resistance: 47 kOhm
• Recommended termination capacity: 150 – 200 pF
• Replacement needle: JN-P110
• Cartridge type: without head shell

OM Q.Bert pre-mounted on SH-4 Black headshell
The OM Q.Bert on the SH-4 Black headshell is a practical and convenient solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm.

Features:
• Universal mount fitting a wide range of S-shaped tonearms
• Ultra high output
• Low wear characteristics

Tailored specifically for scratch, the OM Q.Bert provides unrivaled tracking ability and sonic characteristics.

Technical Data:
Stylus Type Spherical
Tracking Force 3.0 g
Output Voltage 11 mV
Frequency Range 20-18.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 11 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 22 dB
Frequency range at -3dB - 20-18.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 90 μm
Compliance, dynamic lateral - 12 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm
Tracking force range - 2 - 4 g
Tracking force recommended - 3 g

Tracking angle - 20°
Internal impedance, DC resistance - 1.680 Ohm
Internal inductance - 920 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-400 pF
OM cartridge weight incl. extra weight - 5 g
Replacement stylus unit - Q.Bert

OM Pro S pre-mounted on SH-4 Black
The OM Pro S on the SH-4 Black headshell is a practical and convenient solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm.

Features:
• Universal mount fitting a wide range of S-shaped tonearms
• Correct Baerwald alignment with the major part of tonearms with universal mount
• Spherical stylus minimizes scratching
• Solid cantilever can survive hectic activity at the turntable

The OM Pro S is a consistent performer and a fine all-arounder!

OM Pro S technical data
Stylus Type Spherical
Tracking Force 4.0 g (40 mN)
Output Voltage 5 mV
Frequency Range 20-18.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 5 mV
Channel balance at 1kHz - 2 dB
Channel separation at 1kHz - 20 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-18.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 70 μm
Compliance, dynamic lateral - 7 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm
Tracking force range - 3 - 5 g
Tracking force recommended - 4 g
Tracking angle - 20°

Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
OM cartridge weight - 5,0 g
OM pre-mounted on SH-4 weight incl. screws - 14,5 g
Replacement stylus unit - Pro S

AT617A - CARTRIDGE STYLUS CLEANER
- Specially formulated polyurethane gel removes dirt particles from stylus
- Gel remains tacky for years
- Surface is washable for repeated use

Der AT-VM95ML ist mit einem nackten
Microlinear-Diamanten ausgestattet, der
durch seinen speziellen Schliff und die für
Line-Contact-Nadeln typischen
geringeren Verzerrungen am Plattenende
(innere Rillen) eine doppelt so hohe
Lebensdauer gewährleistet und sich
zugleich durch einen erweiterten
Frequenzgang und eine bessere
Auflösung der mittleren und hohen
Frequenzen auszeichnet

AT-VMN95ML
VM95 SERIES MICROLINEAR REPLACEMENT STYLUS
Aluminium cantilever
Microlinear Stylus
Nude Square Shank

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

MICROLINEAR STYLUS
Microlinear profile diamond stylus offers high frequency response with less wear and distortion than elliptical or conventional linear contact styli.

Der AT-VM95ML ist mit einem nackten
Microlinear-Diamanten ausgestattet, der
durch seinen speziellen Schliff und die für
Line-Contact-Nadeln typischen
geringeren Verzerrungen am Plattenende
(innere Rillen) eine doppelt so hohe
Lebensdauer gewährleistet und sich
zugleich durch einen erweiterten
Frequenzgang und eine bessere
Auflösung der mittleren und hohen
Frequenzen auszeichnet.

AT-VM95C/H
VM95 SERIES MICROLINEAR STEREO CARTRIDGE ON AT-HS6 HEADSHELL
AT-VM95ML mounted on AT-HS6BK headshell
The total set weight is 15.5g
Assembled and tested in the Audio-Technica Factory in Fukui-Japan

AT-VM95ML
VM95 SERIES MICROLINEAR STEREO CARTRIDGE
The AT-VM95ML, features a Nude Microlinear diamond, not only the Microlinear stylus will permit to double the duration of your stylus. The performance of a line contact stylus, will minimize the “inner groove distortion” as well as providing extended frequency response and maximize resolution in the medium and high frequencies of the audio program material.

material. Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 25,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

MICROLINEAR STYLUS
Microlinear profile diamond stylus offers high frequency response with less wear and distortion than elliptical or conventional linear contact styli.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95C cartridge is fitted onto the 9g aluminium die cast body headshell

Model AT-VM95ML
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 25,000 Hz
Kanaltrennung 23 dB (1 kHz)
Kanalbalance am Ausgang 1.5 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Microlinear
Nadelabmessungen 2.2 x 0.12 mil
Schaftform der Nadel Nude Square Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 10 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95ML
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

Der AT-VM95E ist das neue
Einstiegsmodell von Audio-Technica mit
elliptischer Nadel, das nicht nur den
legendären AT95E ersetzt, sondern auch
von den Entwicklungen des im Jahr 2015
eingeführten AT95EX profitiert.
Der AT-VM95E überzeugt durch ein
optimiertes, markantes Design mit steiferem,
resonanzarmem Gehäuse und – dank zwei
Gewindeeinsätzen im Gehäuse – eine
besonders einfache Montage mit nur zwei
Schrauben, ohne Muttern (mit Headshell oder
in den Tonarm integriert)

• Das Tonabnehmer-Set AT-VM95E/H wird im Audio-TechnicaWerk
in Fukui (Japan) vormontiert, getestet und verpackt.
• Gesamtgewicht 15,5 g

AT-VM95E/H
VM95 SERIES ELLIPTICAL STEREO CARTRIDGE ON AT-HS6 HEADSHELL
AT-VM95E mounted on AT-HS6BK headshell
The total set weight is 15.5g
Assembled and tested in the Audio-Technica Factory in Fukui-Japan

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

ELLIPTICAL BONDED STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95E cartridge is fitted onto the 9g aluminiumdie cast body headshell

Model AT-VM95E/H
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 22,000 Hz
Kanaltrennung 20 dB (1 kHz)
Kanalbalance am Ausgang 2.0 dB (1 kHz)
Ausgangsleistung 4.0 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Elliptical
Nadelabmessungen 0.3 x 0.7 mil
Schaftform der Nadel Bonded Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 17 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 7 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 15.5 g
Abmessungen 21.2 × 21.4 × 62.4 ( H x W x D mm)
Ersatznadel AT-VMN95E

For TN-200 Turntable

Stylus for Concorde MkII Elite Cartridge.

Every once and a while you need to take care of your record player. This is the NP5 diamond stylus replacement needle which is compatible for these record player:
• Mercury
• C62 Black
• T150
• C6 White

Specifications:
• ABS Plastic Composition
• Diamond Stylus Needle
• Plays 3 Speeds (33 1/3, 45 and 78 RPM)

The 2M Series is developed in conjunction with the Danish Industrial designer Møller Jensen Design – the same designer who designed the award winning MC Jubilee and Kontrapunkt series. Inspired by the facets of a diamond, whose contours gracefully trace the grooves on a record’s surface, the 2M’s handsome elegance establishes a great combination of form and functionality.

The name 2M was selected from among several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.

Of course the 2M isn’t just another pretty face. It has been engineered to the highest standards and is congruent with Ortofon’s unrelenting commitment to providing the most precise and accurate reproduction possible without coloration.

The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Bronze features:

The 2M Bronze features a Nude Fine Line diamond, which is particularly suited for demanding applications. The slim profile of the Fine Line stylus will track even the highest frequency information, making it a must for discerning listeners. Additionally, its larger footprint ensures reduced distortion and record wear.

The cartridge body is manufactured from Hopelex, a material which ensures high rigidity while eliminating unwanted resonances. The 2M Bronze uses a special upgraded engine, featuring split pole pins with a silver plated copper wire.

Output voltage at 1000 Hz, 5cm/sec. - 5 mV
Channel balance at 1 kHz - 1 dB
Channel separation at 1 kHz - 26 dB
Channel separation at 15 kHz - 15 dB
Frequency response - 20-20.000 + 2 / - 0 dB
Tracking ability at 315Hz at recommended tracking force - 80 µm
Compliance, dynamic, lateral - 22 µm/mN
Stylus type - Nude Fine Line
Stylus tip radius - r/R 8/40 µm
Tracking force range - 1.4-1.7 g (14-17 mN)
Tracking force, recommended - 1.5 g (15 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1.2 kOhm
Internal inductance - 630 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 150-300 pF
Cartridge colour, body/stylus - Black/Bronze
Cartridge weight - 7.2 g
Replacement stylus unit - 2M Bronze (interchangeable with 2M Black and 2M Black LVB 250)

Each of the 2M Series cartridges has its own individual sonic expression, and all five models together represent the ensemble of five classic variations:

• 2M Mono SE, 2M Mono and 2M 78 are a true mono cartridges for playing mono vinyl records
• 2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth
• 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details
• 2M Bronze adds even more details and resolution but in a very evenhanded way that pays respect to all elements
• 2M Black is the best of everything, true to the groove with resolution and accurate insight into each recording

The 2M Series is developed in conjunction with the Danish Industrial designer Møller Jensen Design – the same designer who designed the award winning MC Jubilee and Kontrapunkt series. Inspired by the facets of a diamond, whose contours gracefully trace the grooves on a record’s surface, the 2M’s handsome elegance establishes a great combination of form and functionality.

The name 2M was selected from among several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.

Of course the 2M isn’t just another pretty face. It has been engineered to the highest standards and is congruent with Ortofon’s unrelenting commitment to providing the most precise and accurate reproduction possible without coloration.

The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Bronze features:

The 2M Bronze features a Nude Fine Line diamond, which is particularly suited for demanding applications. The slim profile of the Fine Line stylus will track even the highest frequency information, making it a must for discerning listeners. Additionally, its larger footprint ensures reduced distortion and record wear.

The cartridge body is manufactured from Hopelex, a material which ensures high rigidity while eliminating unwanted resonances. The 2M Bronze uses a special upgraded engine, featuring split pole pins with a silver plated copper wire.

Output voltage at 1000 Hz, 5cm/sec. - 5 mV
Channel balance at 1 kHz - 1 dB
Channel separation at 1 kHz - 26 dB
Channel separation at 15 kHz - 15 dB
Frequency response - 20-20.000 + 2 / - 0 dB
Tracking ability at 315Hz at recommended tracking force - 80 µm
Compliance, dynamic, lateral - 22 µm/mN
Stylus type - Nude Fine Line
Stylus tip radius - r/R 8/40 µm
Tracking force range - 1.4-1.7 g (14-17 mN)
Tracking force, recommended - 1.5 g (15 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1.2 kOhm
Internal inductance - 630 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 150-300 pF
Cartridge colour, body/stylus - Black/Bronze
Cartridge weight - 7.2 g
Replacement stylus unit - 2M Bronze (interchangeable with 2M Black and 2M Black LVB 250)

Each of the 2M Series cartridges has its own individual sonic expression, and all five models together represent the ensemble of five classic variations:

• 2M Mono SE, 2M Mono and 2M 78 are a true mono cartridges for playing mono vinyl records
• 2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth
• 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details
• 2M Bronze adds even more details and resolution but in a very evenhanded way that pays respect to all elements
• 2M Black is the best of everything, true to the groove with resolution and accurate insight into each recording

The Reloop SPIN cartridge system is suitable for scratching, due to the spherical stylus, and is ideally suited for the portable playback of records. With a high tracking ability, the cartridge always stays in the record groove and does not jump, even during fast manoeuvres. In addition, the stylus has a positive effect on vinyl wear.

FEATURES
• Optimized for portable record playback
• Suitable for scratching due to high tracking ability
• Spherical stylus
• Very low vinyl wearout

TECHNICAL DATA
• Frequency range: 100 Hz - 10 kHz
• Output voltage (3.54 cm/s): 180 - 360 mV
• Tracking force range: 4 - 6 g
• Recommended tracking force: 5 g
• Weight: 1.8 g (+/- 0.5 g)

Spirit level

Spirit level for optimum positioning of a turntable.

Electronic stylus balance

The Measure it S2 Stylus Tracking Force Gauge is a highly accurate electronic balance that is designed for measuring stylus trackingforces up to 5.0 grams in 0.001 gram increments. Each Measure it S2 can easily be calibrated with the included calibration weight. The Measure it S2 has a solid aluminum housing with a 4-digit LCD backlit display. Whenever in doubt about the actual amount of pressure on the diamond tip the 4 digit display of this smart tool will help. Armed with precise information about tracking force, your stylus tip wear can be significantly reduced.

Scope of delivery:
• stylus balance
• calibration weight
• screwdriver
• 2x AAA batteries
• protection case for the meter
• user guide

Features:
• 4 digit LCD-Display with backlight
• Capacity 0 - 5g
• Variance ±0,001g
• Auto calibration function
• Auto off after 60 seconds
• Replacement batteries supplied

Technical Specifications:
• Capacity: 0 - 5g
• Variance: ±0,001g
• Weighting modes: gram (1g = 10mN), ounce (oz), pennyweight (dwt) and carat (ct)
• Display: 4 digit LCD with backlight
• Calibration: Auto calibration using a 5g weight
• Auto off: 60 seconds off
• Replacement battery: 2 x AAA cells, 1,5V
• Operating temperature: +10 - +30°C (50 - 86 degrees Fahrenheit)
• Dimensions (W x H x D): 122 x 27 x 55mm
• Weight: 170g

Cartridge alignment tool

• Tool for cartridge alignment and adjustment
• Special slip-proof tool for defining the turning centre of Pro-Ject tonearms
• Adaptable to accommodate differing tonearm lengths
• Also suitable for other manufacturers’ tonearms
• Suitable for tonearms between 8″ (203mm) and 12″(305mm) effective length

Audiophile MM Cartridge

Lively & robust with a high dynamic range

Intensive research, development and listening tests have been necessary to gain the the desired sound from the new Pick it PRO.

THE DIFFERENCE IN SOUND
Cartridges are electromechanical transducers, where mechanical energy is transformed into an electrical signal. The real difference in sound happens here. The colour and life of the music come from the cartridge.
You cannot judge the cartridge by looking at just one specific part. Experience and the art of fine-tuning make a cartridge unique and special. The perfect combination of components is the key to achieve the great charismatic sound of the Pick it PRO.

Technical Specifications:
• Cartridge principle: MM (Moving-Magnet)
• Output voltage at 1 kHz: 4 mV
• Channel separation at 1 kHz: 22 dB
• Tracking ability at 315Hz: 70 μm
• Frequency response: 20 - 20 000 Hz +/- 2dB
• Stylus type: Elliptical
• Stylus tip radius: r/R 8/18 μm
• Tracking force, range: 1,8 - 2,2 g (mN)
• Tracking force, recommended: 2,0 g (mN)
• Tracking angle: 20°
• Internal impedance, DC resistance: 750 Ohm
• Internal inductance: 450mH
• Recommended load resistance: 47kOhm
• Recommended load capacitance: 150-300pF
• Cartriddge weight: 7,2 g

MM phono cartridge for turntables

Beautiful design and superior sound!

The Pro-Ject Pick it S2 MM is manufactured by the cartridge experts at Ortofon and voiced by the design team at Pro-Ject. It is equipped with a special elliptical stylus tip. It provides detailed sound reproduction and expansive imaging. It is a no-nonsense performer with fascinating musical resources. Attached to a strong cantilever, used in DJ cartridges, this cartridge will not just sound great, it is also very strong.
The cartridge is made from a unique combination of technologies. Among others Ortofon‘s well known split pole pins. This enables it to have a flat frequency response, which compares with MC cartridges. The superior treble output provides a dynamic and warm sound.
Inspired by the diamond found on the stylus, the Pick it S2 MM is a beautiful design featuring a new and unique semi-transparent grey color. It goes perfectly with most Pro-Ject record players.

Features:
• Moving Magnet principle
• Split pole pins enables frequency responses that compares very well to MC cartridges
• Strong cantilever based in high-end DJ cantilevers
• Suitable for low to medium tonearm masses
• 1/2 inch mounting standard
• High trackability
• Pick it S2 MM should be connected to phono MM inputs
• As with most MM cartridges, stylus may be exchanged

Technical Specifications:
• Weight: 7.2 g
• Stylus type: elliptical
• Frequency response: 20 - 20.000 Hz
• Output voltage: 7 mV
• Recommended tracking force: 1,8 g (mN)
• Trackability (315 Hz, lateral): 70 µm
• Recommended load capacitance: 150 - 300 pF
• Recommended load resistance: 47 kΩ

Replacement stylus Nagaoka JTS-80LB for the pickup JT-80LB.

The Nagaoka JT-80LB (Lapis Blue) cartridge with its shiny blue needle insert is the basic model of the series and features an aluminium needle carrier with a set diamond. With its open, powerful sound, it offers exceptional value for money. The cartridge unfolds its full potential after an approx. 80-hour play-in period.

TECHNICAL SPECIFICATIONS:
• Format: Moving magnet type (MM type)
• Output: 5.0 mV (5 cm / sec)
• Frequency characteristic: 20Hz-20,000Hz
• Channel separation: 23dB (1Khz)
• Channel balance: 1.5 dB or less
• Cantilever: Aluminum alloy
• Needle tip: 0.4x0.7mil Ellipse / Joined diamond
• Stylus pressure: 1.3g-1.8g
• Torridge own weight: 6.9g
• Replacement needle: JTS-80LB
• Cartridge type: without head shell

https://www.auditorium.de/attachment/STEREO_3-21_Nagaoka-Abtaster_englisch.pdf

Replacement stylus for Nagaoka MP-150.

To exchange the needle of the MP 150, simply pull off the needle carrier of the system and replace it with the JN-P 150.

Replacement stylus for Nagaoka MP-100.

To exchange the needle of the MP 100, simply pull off the needle carrier of the system and replace it with the JN-P 100.

The design of the MP-150 has been significantly refined. Higher quality magnet materials, a better cantilever and a bonded diamond ensure better tracking and detail reproduction. The bass range also sounds more balanced.

TECHNICAL SPECIFICATIONS:
• Principle: MI - High Output (for the MM input)
• Weight: 6.5g
• Height: 18mm
• Needle cut: Elliptical 0.4x0.7mm
• Needle carrier: stiffened cone aluminum tube
• Frequency response: 20 - 20,000 Hz
• Output voltage (1kHz, 5cm/sec): 4.5mV
• Channel separation (1kHz): > 24 dB
• Channel balance (1kHz): < 1.5 dB
• Needle compliance: 20 µm/mN
• Recommended tracking force: 18 mN (15-20 mN)
• Recommended termination resistance: 47 kOhm
• Recommended termination capacity: 150 – 200 pF
• Replacement needle: JN-P150
• Cartridge type: without head shell

With its round diamond, the MP-100 cartridge is particularly suitable for older records. Even scratches and dirt do not affect the pleasant, neutral sound that this system makes possible. The MP-100 is the most affordable scanner in the MP range.

TECHNICAL SPECIFICATIONS:
• Principle: MI - High Output (for the MM input)
• Weight: 6.5g
• Height 18mm
• Needle cut: Round 0.6mm
• Cantilever: aluminum
• Frequency response: 20 - 20,000 Hz
• Output Voltage (1kHz, 5cm/sec): 5.0mV
• Channel separation (1kHz): > 22 dB
• Channel balance (1kHz): < 2.0 dB
• Needle compliance: 19 µm/mN
• Recommended tracking force: 21 mN (18-23 mN)
• Recommended termination resistance: 47 kOhm
• Recommended termination capacity: 150 – 200 pF
• Replacement needle: JN-P100
• Cartridge type: without head shell

Stylus for Ortofon VNL.

In ViNyL we trust
Even before the launch of the Concorde MkII, we have always studied the feedback of our customers and how they utilize our products.

Skilled DJs demand specialized tools that can help them push their creativity to the edge – consistently testing the boundaries in the realm of performance.

Understanding this and reflecting our extensive experience in industrial design and technological know-how, we present the new Ortofon VNL cartridge – a model tailored uniquely to the unrelenting demands of modern turntablists and portablists.

The new VNL features and improvements
• Extra resistance to hardcore scratching and back spinning
• High tracking performance for both DVS usage and real vinyl
• Optimal balance of output and of sound quality

Technological improvements have been applied for the benefits of all users:
- Ultrasonic welding of the components ensures high rigidity and freedom from resonances.
- Robotic assembly of stylus assembly offers high precision and uniformity of industrial production.

VNL III compliance, dynamic lateral 14 μm/m N - Firm

DJs can easily identify which stylus type best suits their individual DJ style and enables their absolute best performance capability.

VNL technical data

Stylus Type: Sperical
Tracking Force: 4,0 g
Output Voltage: 6mV
Frequency Range: 20-20.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel separation at 1kHz - 20 dB
Frequency response 20 Hz - 20 kHz -2/+4 dB
Tracking ability at 315 Hz at recommmended tracking force:

VNL III 90 μm

VNL III 14 μm/m N

Tracking force range - 3 - 5 g
Tracking force recommended - 4 g
Antiskating - for best backcueing performance use “0”
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Cartridge weight - 6,5 g
Replacement stylus units: VNL I, VNL II, VNL III

Exclusive features
The VNL features a spherical stylus which is perfect for tough groove handling. Furthermore, it reduces record wear when scratching and back-cueing to an absolute minimum.

The broad stance of the VNL features solid and robust design elements characteristic to Ortofon, with colors meticulously selected to emphasize sturdiness and DJ aesthetics: the cartridge body has been designed to provide easy mounting and alignment on a variety of headshells.

The VNL provides excellent compatibility when used in an assortment of playback systems, ensuring it stays in the groove under the most demanding conditions.

VNL Userguide: https://www.ortofon.com/media/151234/5-800161-12_vnl_userguide_08_20_web.pdf

Stylus for Ortofon VNL.

In ViNyL we trust
Even before the launch of the Concorde MkII, we have always studied the feedback of our customers and how they utilize our products.

Skilled DJs demand specialized tools that can help them push their creativity to the edge – consistently testing the boundaries in the realm of performance.

Understanding this and reflecting our extensive experience in industrial design and technological know-how, we present the new Ortofon VNL cartridge – a model tailored uniquely to the unrelenting demands of modern turntablists and portablists.

The new VNL features and improvements
• Extra resistance to hardcore scratching and back spinning
• High tracking performance for both DVS usage and real vinyl
• Optimal balance of output and of sound quality

Technological improvements have been applied for the benefits of all users:
- Ultrasonic welding of the components ensures high rigidity and freedom from resonances.
- Robotic assembly of stylus assembly offers high precision and uniformity of industrial production.

VNL II compliance, dynamic lateral 15 μm/m N - Rigid

DJs can easily identify which stylus type best suits their individual DJ style and enables their absolute best performance capability.

VNL technical data

Stylus Type: Sperical
Tracking Force: 4,0 g
Output Voltage: 6mV
Frequency Range: 20-20.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel separation at 1kHz - 20 dB
Frequency response 20 Hz - 20 kHz -2/+4 dB
Tracking ability at 315 Hz at recommmended tracking force:

VNL II 90 μm

VNL II 15 μm/m N

Tracking force range - 3 - 5 g
Tracking force recommended - 4 g
Antiskating - for best backcueing performance use “0”
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Cartridge weight - 6,5 g
Replacement stylus units: VNL I, VNL II, VNL III

Exclusive features
The VNL features a spherical stylus which is perfect for tough groove handling. Furthermore, it reduces record wear when scratching and back-cueing to an absolute minimum.

The broad stance of the VNL features solid and robust design elements characteristic to Ortofon, with colors meticulously selected to emphasize sturdiness and DJ aesthetics: the cartridge body has been designed to provide easy mounting and alignment on a variety of headshells.

The VNL provides excellent compatibility when used in an assortment of playback systems, ensuring it stays in the groove under the most demanding conditions.

VNL Userguide: https://www.ortofon.com/media/151234/5-800161-12_vnl_userguide_08_20_web.pdf

Stylus for Ortofon VNL.

In ViNyL we trust
Even before the launch of the Concorde MkII, we have always studied the feedback of our customers and how they utilize our products.

Skilled DJs demand specialized tools that can help them push their creativity to the edge – consistently testing the boundaries in the realm of performance.

Understanding this and reflecting our extensive experience in industrial design and technological know-how, we present the new Ortofon VNL cartridge – a model tailored uniquely to the unrelenting demands of modern turntablists and portablists.

The new VNL features and improvements
• Extra resistance to hardcore scratching and back spinning
• High tracking performance for both DVS usage and real vinyl
• Optimal balance of output and of sound quality

Technological improvements have been applied for the benefits of all users:
- Ultrasonic welding of the components ensures high rigidity and freedom from resonances.
- Robotic assembly of stylus assembly offers high precision and uniformity of industrial production.

VNL \ compliance, dynamic lateral 16 μm/m N - Flexible

DJs can easily identify which stylus type best suits their individual DJ style and enables their absolute best performance capability.

VNL technical data

Stylus Type: Sperical
Tracking Force: 4,0 g
Output Voltage: 6mV
Frequency Range: 20-20.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel separation at 1kHz - 20 dB
Frequency response 20 Hz - 20 kHz -2/+4 dB
Tracking ability at 315 Hz at recommmended tracking force:

VNL I 100 μm

VNL I 16 μm/m N

Tracking force range - 3 - 5 g
Tracking force recommended - 4 g
Antiskating - for best backcueing performance use “0”
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Cartridge weight - 6,5 g
Replacement stylus units: VNL I, VNL II, VNL III

Exclusive features
The VNL features a spherical stylus which is perfect for tough groove handling. Furthermore, it reduces record wear when scratching and back-cueing to an absolute minimum.

The broad stance of the VNL features solid and robust design elements characteristic to Ortofon, with colors meticulously selected to emphasize sturdiness and DJ aesthetics: the cartridge body has been designed to provide easy mounting and alignment on a variety of headshells.

The VNL provides excellent compatibility when used in an assortment of playback systems, ensuring it stays in the groove under the most demanding conditions.

VNL Userguide: https://www.ortofon.com/media/151234/5-800161-12_vnl_userguide_08_20_web.pdf

In ViNyL we trust
Even before the launch of the Concorde MkII, we have always studied the feedback of our customers and how they utilize our products.

Skilled DJs demand specialized tools that can help them push their creativity to the edge – consistently testing the boundaries in the realm of performance.

Understanding this and reflecting our extensive experience in industrial design and technological know-how, we present the new Ortofon VNL cartridge – a model tailored uniquely to the unrelenting demands of modern turntablists and portablists.

Contains 1x Stylus VNL II!

The new VNL features and improvements
• Extra resistance to hardcore scratching and back spinning
• High tracking performance for both DVS usage and real vinyl
• Optimal balance of output and of sound quality

Technological improvements have been applied for the benefits of all users:
- Ultrasonic welding of the components ensures high rigidity and freedom from resonances.
- Robotic assembly of stylus assembly offers high precision and uniformity of industrial production.

DJs can easily identify which stylus type best suits their individual DJ style and enables their absolute best performance capability.

VNL technical data

Stylus Type: Sperical
Tracking Force: 4,0 g
Output Voltage: 6mV
Frequency Range: 20-20.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel separation at 1kHz - 20 dB
Frequency response 20 Hz - 20 kHz -2/+4 dB
Tracking ability at 315 Hz at recommmended tracking force:

VNL I 100 μm
VNL II 90 μm
VNL III 90 μm
Compliance, dynamic lateral:

VNL I 16 μm/m N
VNL II 15 μm/m N
VNL III 14 μm/m N

Tracking force range - 3 - 5 g
Tracking force recommended - 4 g
Antiskating - for best backcueing performance use “0”
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Cartridge weight - 6,5 g
Replacement stylus units: VNL I, VNL II, VNL III

Exclusive features
The VNL features a spherical stylus which is perfect for tough groove handling. Furthermore, it reduces record wear when scratching and back-cueing to an absolute minimum.

The broad stance of the VNL features solid and robust design elements characteristic to Ortofon, with colors meticulously selected to emphasize sturdiness and DJ aesthetics: the cartridge body has been designed to provide easy mounting and alignment on a variety of headshells.

The VNL provides excellent compatibility when used in an assortment of playback systems, ensuring it stays in the groove under the most demanding conditions.

VNL Userguide: https://www.ortofon.com/media/151234/5-800161-12_vnl_userguide_08_20_web.pdf

Extra weight for Ortofon OM cartridge
Specifications:

- Weight: 2.5 g
- Material: Brass

Screws for mounting OM cartridges on the headshell

Set of 2 screws and 2 nuts for OM series (2.5x9mm)

Ortofon HiFi Maintenance set
Comprises 1 PC fibre stylus brush and 1 PC screwdriver in a plastic cylinder.

rtofon DS-3 - a high precision digital stylus pressure gauge
DS-3 is a new lightweight compact digital stylus pressure gauge model. The DS-3 is a miniature ultra precision non-magnetic instrument that tunes your tonearm to the highest possible degree. The DS-3 scale is factory pre-calibrated for high accuracy measurements with the tolerance of +/-0.01 g.

How to use the DS-3
• Turn on the device by pressing ON button. The display will show 0000.
• Press the UNIT button to select the measurement unit. The default setting is gram/g.
• Place the stylus on the measurement plate on the right side of the device. Display will start blinking. It will stop blinking when the measurement is completed. The value displayed on the screen is the stylus pressure.
• The display screen will automatically dim to saving mode after 5 seconds of inactivity and turn off after 60 seconds of inactivity.
• When a battery runs out, a LO indicator will flash on the screen. Then replace both batteries.
• PCS button balances count by calculating the average weight of one piece-weight called a unit weight, then applying it to the total weight of what you are trying to count. Firstly, weigh one PC, then weigh the bundle, then push the PCS button and on the display you’ll get a number of PCS.

Technical data and precautions
Sensitivity - 0.01g
Operational weight range - 0.1g to 200g
Battery - 2 × AAA
Size - (L) 120mm × (W) 60mm × (H) 17mm
Weight - 70g
LCD screen with back lighting
Auto off function
Protect the device against high temperatures, dust and humidity
Carefully lower the measurement object on the measurement plate
Operating temperature range +10⁰ - +30⁰C
Do not place objects weighting more than 200 g on the measurement plate
Do not place the device on an uneven surface, it may result in not accurate measurements

Exchangeable reinforced finger lift for Concorde MkII series
• Tapered shape, robustness where needed
• Metal ring is “unbroken”
• Colour options: Red, Black, Yellow and Orange
• Wider grip area
• Grip texture
• Graphics area

The new finger lift is one of the major improvements: it’s now stand alone replaceable part.

Available in Black, Red, Orange, Yellow and White colors which is perfect to personalize the cartridge the way you want it.

GT Replacement stylus for tough handling - extremely sturdy for scratching DJs
GT was developed by Ortofon in close co-operation with SWS Audio GmbH. The cartridge was named "Great and Tough" and was based on the construction of the well-known Ortofon Series 500 design - mend for standard half inch mounting - in a black housing with white printing.

The vital parts in the GT are based on a very robust and reliable parts used in Scratch. Further, during development of GT, efforts were also concentrated on supplying a very high output of 8 mV and improvement of frequency response to give higher resolution and sound image.

Tracking avility is decisive for the DJs especially when scratching and back-cuing. In this situation raise of tracking force could be an immediate, but in many cases not very effective solution. The reason is that the antiskating adjustment, if not at a very moderate level, will double the skating effect when back-cuing.

As a rule, never use more than half of normal antiskating related to the tracking force! To make GT even more resistant against violent handling, such as drop or touch of fingers, we have made a rubber suspension of the cantilever even more rigid against axial pull.

GT Stylus Technical data
Output voltage at 1000Hz, 5cm/sec. - 8 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 25 dB
Channel separation at 15 kHz - 18 dB
Frequency range at -3dB - 20-20.000 Hz
Frequency response - 20-18.000 Hz +/- 2 dB
Tracking ability at 315 Hz at recommmende tracking force - 80 μm
Compliance, dynamic lateral - 6 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm

Tracking force range - 3.0-5.0 g (30-50 mN)
Tracking force recommended - 4.0 g (40 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1000 Ohm
Internal inductance - 580 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-400 pF

Compatible with cartridges - GT (discontinued and no longer available)

Made From Scratch replacement stylus
To support our customers who own the Concorde MFS we will continue to manufacture replacement stylus MFS.

Features:
- Spherical stylus, which can stand up to heavy back-cueing
- High output for clear sound from a mixer/preamplifier
- Non-compromising energetic sound quality

Made From Scratch stylus Technical data
Output voltage at 1000Hz, 5cm/sec. - 7 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 25 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Frequency response - 20-15.000 Hz 3dB/-2dB
Tracking ability at 315 Hz at recommmende tracking force - 80 μm
Compliance, dynamic lateral - 6 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm

Tracking force range - 3.0-5.0 g (30-50 mN)
Tracking force recommended - 4.0 g (40 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Concorde cartridge weight - 18.5 g

Compatible with cartridges - Made From Scratch (discontinued and no longer available)

Digitrack Limited Edition stylus
The Digitrack Limited Edition is the perfect marriage of easy and function. You can now manipulate MP3's with the style and feel of a turntablist and the tradition of a turntable. The Digitrack Limited Edition responds to the DJs who make extensive use of timecoded vinyl applications.

Digitrack Limited Edition low wear design and tailored frequency response increase the lifespan of timecoded vinyl records, and provides high quality sound reproduction for playing conventional vinyl records as well.

The Digitrack Limited Edition also features excellent groove-handling capabilities for scratch and mix performance, as well as increased output voltage for improved TCV performance and better sound quality from your mixer's phono preamps.

Digitrack Limited Edition Technical data
Output voltage at 1000Hz, 5cm/sec. - 8 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 22 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Frequency response - 20-18.000 Hz +3/-2 dB

Tracking ability at 315 Hz at recommmende tracking force - 90 μm
Compliance, dynamic lateral - 12 μm/m N
Stylus type - Spherical
Tracking force range - 2.0-4.0 g (20-40 mN)
Tracking force recommended - 3.0 g (30 mN)
Concorde cartridge weight - 18.5 g

Compatible with cartridges - Digitrack Limited Edition (discontinued and no longer available)

Nightclub S Replacement Stylus
The Nighclub S stylus is amongst the top performers in its category, Scratch and Mix.

A spherical diamond and a customised design provide the basis for the cartridge's undeniable supremacy.

The stylus remains in the groove during the scratching and back-cueing, making it unfailingly reliable - even when giving a night-long performance.

Nightclub S Stylus Technical Data
Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 23 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-22.000 Hz
Frequency response - 20-18.000 Hz +3 / - 2 dB
Tracking ability at 315 Hz at recommmende tracking force - 80 μm
Compliance, dynamic lateral - 7 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm

Tracking force range - 2.0-5.0 g (20-50 mN)
Tracking force recommended - 3.0 g (30 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Concorde cartridge weight - 18.5 g

Compatible with cartridges - Nightclub Series

Nightclub E Replacement stylus
Nightclub E is equipped with Special Elliptical diamond. Perfect for usage in clubs. Superb sound quality.

Club DJs and studio workers believe the Nightclub E to be an absolute high-end cartridge. It is indeed a no-nonsence performer with fascinating musical resources.

It's output is superb with a frequency responce rating high enough to compare the Nightclub E to any audiophile cartridge.

The special elliptical stylus guarantees sound with insignificant scratching.

Nightclub E Stylus Technical Data
Output voltage at 1000Hz, 5cm/sec. - 8 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 23 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-22.000 Hz
Frequency response - 20-20.000 Hz +/- 1.5 dB
Tracking ability at 315 Hz at recommmende tracking force - 65 μm
Compliance, dynamic lateral - 20 μm/m N
Stylus type - Elliptical
Stylus tip radius - r/R 8/18 μm

Tracking force range - 2.0-5.0 g (20-50 mN)
Tracking force recommended - 3.0 g (30 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1000 Ohm
Internal inductance - 580 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Concorde cartridge weight - 18.5 g

Compatible with cartridges - Nightclub Series

OM Scratch White pre-mounted on SH-4 Blue headshell
The OM Scratch White on the SH-4 Black headshell is a practical and convenient solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm.

Features:
• Universal mount fitting a wide range of S-shaped tonearms
• Correct Baerwald alignment with the major part of tonearms with universal mount
• Spherical stylus minimizes scratching
• Increased tracking ability
• Reinforced rubber suspension

High output and maximum scratch performance guaranteed!

OM Scratch White technical data
Stylus Type Spherical
Tracking Force 4.0 g (40 mN)
Output Voltage 7 mV
Frequency Range 20-15.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 7 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 25 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Frequency response - 20-15.000 Hz 3dB/-2dB
Tracking ability at 315 Hz at recommmended tracking force - 80 μm
Compliance, dynamic lateral - 6 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm
Tracking force range - 3,0-5,0 g (30-50 mN)
Tracking force recommended - 4,0 g (40 mN)
Tracking angle - 20°

Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
OM cartridge weight - 5 g
OM pre-mounted on SH-4 weight incl. screws - 14,5 g

Replacement stylus unit - Scratch White

ATN-XP3
Replacement Stylus for AT-XP3
Conical Bonded Stylus
Carbon fibre-reinforced ABS cantilever
Durable design for DJ application

AT-XP3
Dual Moving Magnet Stereo Cartridge
The AT-XP series cartridges provide a high quality sound for vinyl DJ’s. Offering all of the features of a DJ cartridge, but with a Hi-fi sound, the XP series are perfect for the stage and club DJ who prioritises sound quality.

• Audiophile DJ cartridge equipped with a conical stylus
• VM dual magnet construction
• Durable robust design for high-quality specialist DJ playback
• Signal output level and output impedance characteristics suited for professional DJ applications
• Carbon fiber-reinforced ABS cantilever and nylon wire suspension ensure precise tracking
• Compatible with the replacement styli ATN-XP5 and ATN-XP7 for an upgrade

Specifications:
• Model AT-XP3
• Mounting Half-inch
• Frequency Response 20 to 18,000 Hz
• Channel Separation 20 dB (1 kHz)
• Output Channel Balance 2.0 dB (1 kHz)
• Output Voltage 5.5 mV (at 1 kHz, 5 cm/sec)
• Vertical Tracking Angle 20 degrees
• Vertical Tracking Force Range 2.0 to 4.0g (standard 3.0 g)
• Stylus Shape Conical
• Stylus Size 0.6 mil
• Stylus Construction Bonded Round Shank
• Cantilever Carbon reinforced ABS
• Coil Impedance 6,700 ohms (1 kHz)
• Coil Inductance 550 mH (1 kHz)
• Static Compliance 20 x 10 – 6 cm / dyne
• Dynamic Compliance 6.0 x 10 – 6 cm / dyne (100 Hz)
• Recommended Load Impedance 47,000 Ω
• Recommended Load Capacitance 100-200 pF
• Cartridge Weight 6.2g
• Dimensions 17.2 x 17.8 x 28.3 ( H x W x D mm)
• Replacement Stylus ATN-XP3
• Accessories Included Two 11 mm installation screws, Two 8 mm installation screws, Two washers, Two Nut, Non-magnetic screwdriver

manual: https://eu.audio-technica.com/resources/AT-XP3_UM_112301371_V1_11L_web_180620.pdf

Die-cast aluminium body
Integral finger lift
Includes terminals quad wire
1 pair of 10mm screws and 1 pair of 8mm screws
1 pair of M2.6 nuts with plastic washer
Available in Black and Silver

Die-cast aluminium body
Integral finger lift
Includes terminals quad wire
1 pair of 10mm screws and 1 pair of 8mm screws
1 pair of M2.6 nuts with plastic washer
Available in Black and Silver

Der AT-VM95SH besitzt eine nackte
Shibata-Nadel – hochgeschätzt
insbesondere für audiophile HighendAnwendungen.
Der Shibata-Schliff ermöglicht satte,
volle Bässe und Mitten und einen
Frequenzgang bis 25.000 Hz.

AT-VMN95SH
VM95 SERIES SHIBATA REPLACEMENT STYLUS
Aluminium cantilever
Shibata Stylus
Nude Square Shank

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

SHIBATA STYLUS
Provides a beautiful mid-high range Shibata-signature sound and strong mid-range volume.

Der AT-VM95SH besitzt eine nackte
Shibata-Nadel – hochgeschätzt
insbesondere für audiophile HighendAnwendungen.
Der Shibata-Schliff ermöglicht satte,
volle Bässe und Mitten und einen
Frequenzgang bis 25.000 Hz.

AT-VM95SH
VM95 SERIES SHIBATA STEREO CARTRIDGE
The AT-VM95SH, features a Nude Shibata stylus, one of the most acclaimed stylus format by high end audiophiles. The Shibata stylus produces mid and bass sounds strong and rich in addition to offer a frequency response up to 25,000 Hz.

Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 25,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

SHIBATA STYLUS
Provides a beautiful mid-high range Shibata-signature sound and strong mid-range volume.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95C cartridge is fitted onto the 9g aluminium die cast body headshell

Model AT-VM95SH
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 25,000 Hz
Kanaltrennung 23 dB (1 kHz)
Kanalbalance am Ausgang 1.5 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Microlinear
Nadelabmessungen 2.7 x 0.26mil
Schaftform der Nadel Nude Square Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 10 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95SH
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

Der AT-VM95SH besitzt eine nackte
Shibata-Nadel – hochgeschätzt
insbesondere für audiophile HighendAnwendungen.
Der Shibata-Schliff ermöglicht satte,
volle Bässe und Mitten und einen
Frequenzgang bis 25.000 Hz.

AT-VM95SH
VM95 SERIES SHIBATA STEREO CARTRIDGE
The AT-VM95SH, features a Nude Shibata stylus, one of the most acclaimed stylus format by high end audiophiles. The Shibata stylus produces mid and bass sounds strong and rich in addition to offer a frequency response up to 25,000 Hz.

Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 25,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

SHIBATA STYLUS
Provides a beautiful mid-high range Shibata-signature sound and strong mid-range volume.

NO USE OF NUTS
VM95 Series cartridges features two M2.6 threaded inserts allowing the installation of the cartridge onto tonearm or removable headshell without the use of nuts.Each cartridge is provided with one pair of 8mm M2.6 screws, one pair of 11mm M2.6 screws and two plastic washers.

Model AT-VM95SH
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 25,000 Hz
Kanaltrennung 23 dB (1 kHz)
Kanalbalance am Ausgang 1.5 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Microlinear
Nadelabmessungen 2.7 x 0.26mil
Schaftform der Nadel Nude Square Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 10 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95SH
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

Der AT-VM95ML ist mit einem nackten
Microlinear-Diamanten ausgestattet, der
durch seinen speziellen Schliff und die für
Line-Contact-Nadeln typischen
geringeren Verzerrungen am Plattenende
(innere Rillen) eine doppelt so hohe
Lebensdauer gewährleistet und sich
zugleich durch einen erweiterten
Frequenzgang und eine bessere
Auflösung der mittleren und hohen
Frequenzen auszeichnet.

AT-VM95ML
VM95 SERIES MICROLINEAR STEREO CARTRIDGE
The AT-VM95ML, features a Nude Microlinear diamond, not only the Microlinear stylus will permit to double the duration of your stylus. The performance of a line contact stylus, will minimize the “inner groove distortion” as well as providing extended frequency response and maximize resolution in the medium and high frequencies of the audio program material.

material. Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 25,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

MICROLINEAR STYLUS
Microlinear profile diamond stylus offers high frequency response with less wear and distortion than elliptical or conventional linear contact styli.

NO USE OF NUTS
VM95 Series cartridges features two M2.6 threaded inserts allowing the installation of the cartridge onto tonearm or removable headshell without the use of nuts.Each cartridge is provided with one pair of 8mm M2.6 screws, one pair of 11mm M2.6 screws and two plastic washers.

Model AT-VM95ML
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 25,000 Hz
Kanaltrennung 23 dB (1 kHz)
Kanalbalance am Ausgang 1.5 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Microlinear
Nadelabmessungen 2.2 x 0.12 mil
Schaftform der Nadel Nude Square Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 10 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95ML
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

Der AT-VM95EN besitzt eine nackte,
elliptische Diamantnadel mit Rundschaft,
die aus einem Stück geschliffen und
direkt in den Nadelträger eingesetzt
wird. Auf diese Weise lässt sich ein
leichteres, steiferes Übertragungssystem
realisieren als mit einer gefassten
Diamantnadel mit Titan-Rundschaft wie
beim AT-VM95E. Die nackte
Diamantnadel ist zwar um einiges
kostspieliger, bietet aber auch eine
hörbar bessere Audioqualität mit
besonders hoher Klangtreue bei der
Höhenwiedergabe und hervorragendem
Impulsverhalten.

AT-VMN95EN
VM95 SERIES ELLIPTICAL NUDE REPLACEMENT STYLUS
Aluminium cantilever
Elliptical Nude Stylus
Nude Round Shank

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

ELLIPTICAL NUDE STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

AT-VM95EN vormontiert auf Headshell AT-HS6BK
• Das Tonabnehmer-Set AT-VM95EN/H wird im Audio-Technica Werk in Fukui (Japan) vormontiert, getestet und verpackt.
Gesamtgewicht 15,5 g

Der AT-VM95EN besitzt eine nackte,
elliptische Diamantnadel mit Rundschaft,
die aus einem Stück geschliffen und
direkt in den Nadelträger eingesetzt
wird. Auf diese Weise lässt sich ein
leichteres, steiferes Übertragungssystem
realisieren als mit einer gefassten
Diamantnadel mit Titan-Rundschaft wie
beim AT-VM95E. Die nackte
Diamantnadel ist zwar um einiges
kostspieliger, bietet aber auch eine
hörbar bessere Audioqualität mit
besonders hoher Klangtreue bei der
Höhenwiedergabe und hervorragendem
Impulsverhalten.

Aluminium-Nadelträger
• Ausgangsspannung 3,5 mV
• Gehäuse kompatibel mit allen Abtastnadeln der Serie VM95
• Frequenzgang 20 bis 23.000 Hz

AT-VM95EN
VM95 SERIES ELLIPTICAL NUDE STEREO CARTRIDGE
The AT-VM95EN, features a Nude Elliptical Diamond. The construction of the stylus being a one piece diamond with a round shank inserted in the cantilever creates a lighter and more rigid transmission system than a diamond tip bonded on a round titanium shank such as in the AT-VM95E. Also the use of nude diamond implies a substantial difference in pricing, yet the quality of the reproduction will be immediately noticed, specifically in the fidelity of high frequencies and in the quality of the transient responses.

Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 23,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

ELLIPTICAL NUDE STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95E cartridge is fitted onto the 9g aluminiumdie cast body headshell

Model AT-VM95EN
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 23,000 Hz
Kanaltrennung 22 dB (1 kHz)
Kanalbalance am Ausgang 2.0 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Elliptical
Nadelabmessungen 0.3 x 0.7 mil
Schaftform der Nadel Nude Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 7 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95EN
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

Der AT-VM95EN besitzt eine nackte,
elliptische Diamantnadel mit Rundschaft,
die aus einem Stück geschliffen und
direkt in den Nadelträger eingesetzt
wird. Auf diese Weise lässt sich ein
leichteres, steiferes Übertragungssystem
realisieren als mit einer gefassten
Diamantnadel mit Titan-Rundschaft wie
beim AT-VM95E. Die nackte
Diamantnadel ist zwar um einiges
kostspieliger, bietet aber auch eine
hörbar bessere Audioqualität mit
besonders hoher Klangtreue bei der
Höhenwiedergabe und hervorragendem
Impulsverhalten.

Aluminium-Nadelträger
• Ausgangsspannung 3,5 mV
• Gehäuse kompatibel mit allen Abtastnadeln der Serie VM95
• Frequenzgang 20 bis 23.000 Hz

AT-VM95EN
VM95 SERIES ELLIPTICAL NUDE STEREO CARTRIDGE
The AT-VM95EN, features a Nude Elliptical Diamond. The construction of the stylus being a one piece diamond with a round shank inserted in the cantilever creates a lighter and more rigid transmission system than a diamond tip bonded on a round titanium shank such as in the AT-VM95E. Also the use of nude diamond implies a substantial difference in pricing, yet the quality of the reproduction will be immediately noticed, specifically in the fidelity of high frequencies and in the quality of the transient responses.

Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 23,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

ELLIPTICAL NUDE STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

NO USE OF NUTS
VM95 Series cartridges features two M2.6 threaded inserts allowing the installation of the cartridge onto tonearm or removable headshell without the use of nuts.Each cartridge is provided with one pair of 8mm M2.6 screws, one pair of 11mm M2.6 screws and two plastic washers.

Model AT-VM95EN
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 23,000 Hz
Kanaltrennung 22 dB (1 kHz)
Kanalbalance am Ausgang 2.0 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Elliptical
Nadelabmessungen 0.3 x 0.7 mil
Schaftform der Nadel Nude Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 7 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95EN
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

Der AT-VM95E ist das neue
Einstiegsmodell von Audio-Technica mit
elliptischer Nadel, das nicht nur den
legendären AT95E ersetzt, sondern auch
von den Entwicklungen des im Jahr 2015
eingeführten AT95EX profitiert.
Der AT-VM95E überzeugt durch ein
optimiertes, markantes Design mit steiferem,
resonanzarmem Gehäuse und – dank zwei
Gewindeeinsätzen im Gehäuse – eine
besonders einfache Montage mit nur zwei
Schrauben, ohne Muttern (mit Headshell oder
in den Tonarm integriert)

• Aluminium-Nadelträger
• Ausgangsspannung 4,0 mV
• Gehäuse kompatibel mit allen Abtastnadeln der Serie VM95
• Ersatz für AT95E und AT95EX
• Frequenzgang 20 bis 22.000 Hz

AT-VM95E
VM95 SERIES ELLIPTICAL STEREO CARTRIDGE
The AT-VM95E, the new Audio-Technica entry model Elliptical cartridge will replace the legendary AT95E and take advantage of the developments of the AT95EX introduced in 2015. The AT-VM95E features an improved and distinctive design resulting in a more rigid low resonance housing, and two threaded inserts in the cartridge body enabling it to be mounted to the headshell or on an integral tonearm with just two screws, no nuts.

Aluminium cantilever
4.0mV output voltage
Compatible body with all VM95 Series stylus assemblies
Replacement for AT95E and AT95EX
20 to 22,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

ELLIPTICAL BONDED STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

NO USE OF NUTS
VM95 Series cartridges features two M2.6 threaded inserts allowing the installation of the cartridge onto tonearm or removable headshell without the use of nuts.Each cartridge is provided with one pair of 8mm M2.6 screws, one pair of 11mm M2.6 screws and two plastic washers.

Model AT-VM95E
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 22,000 Hz
Kanaltrennung 20 dB (1 kHz)
Kanalbalance am Ausgang 2.0 dB (1 kHz)
Ausgangsleistung 4.0 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Elliptical
Nadelabmessungen 0.3 x 0.7 mil
Schaftform der Nadel Bonded Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 17 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 7 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95E
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers

AT-VM95C/H
VM95 SERIES CONICAL STEREO CARTRIDGE ON AT-HS6 HEADSHELL
AT-VM95C mounted on AT-HS6BK headshell
The total set weight is 15.5g
Assembled and tested in the Audio-Technica Factory in Fukui-Japa

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

CONICAL BONDED STYLUS
The benefit of conical styli, even if the cartridge is "lean", is the ball surface of the stylus touches the groove of vinyl records precisely.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95C cartridge is fitted onto the 9g aluminium die cast body headshell

Model AT-VM95C/H
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 20,000 Hz
Kanaltrennung 18 dB (1 kHz)
Kanalbalance am Ausgang 2.5 dB (1 kHz)
Ausgangsleistung 4.0 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Conical
Nadelabmessungen 0.6 mil
Schaftform der Nadel Bonded Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 17 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 6.5 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 15.5 g
Abmessungen 21.2 × 21.4 × 62.4 ( H x W x D mm)
Ersatznadel AT-VMN95C

The AT-VM95C, the new Audio-Technica entry model Conical cartridge will replace the legendary AT90 Series models such as AT91, AT91R and CN5625AL

Also the AT-VM95C is a “budget” cartridge featuring a conical stylus, the compatibility in the range will allow to upgrade with any of the 4 other LP styli of the Series such as Elliptical, Elliptical Nude, Microlinear and Shibata.

Aluminium cantilever
4.0mV output voltage
Compatible body with all VM95 Series stylus assemblies
Replacement for AT91, AT91R and CN5625AL

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

CONICAL BONDED STYLUS
The benefit of conical styli, even if the cartridge is "lean", is the ball surface of the stylus touches the groove of vinyl records precisely.

Model AT-VM95C
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 20,000 Hz
Kanaltrennung 18 dB (1 kHz)
Kanalbalance am Ausgang 2.5 dB (1 kHz)
Ausgangsleistung 4.0 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Conical
Nadelabmessungen 0.6 mil
Schaftform der Nadel Bonded Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 17 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 6.5 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95C
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers