Cartridges & Styluses 160 Items

Die-cast aluminium body
Integral finger lift
Includes terminals quad wire
1 pair of 10mm screws and 1 pair of 8mm screws
1 pair of M2.6 nuts with plastic washer
Available in Black and Silver

Die-cast aluminium body
Integral finger lift
Includes terminals quad wire
1 pair of 10mm screws and 1 pair of 8mm screws
1 pair of M2.6 nuts with plastic washer
Available in Black and Silver

The AT-VM95C, the new Audio-Technica entry model Conical cartridge will replace the legendary AT90 Series models such as AT91, AT91R and CN5625AL

Also the AT-VM95C is a “budget” cartridge featuring a conical stylus, the compatibility in the range will allow to upgrade with any of the 4 other LP styli of the Series such as Elliptical, Elliptical Nude, Microlinear and Shibata.

Aluminium cantilever
4.0mV output voltage
Compatible body with all VM95 Series stylus assemblies
Replacement for AT91, AT91R and CN5625AL

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

CONICAL BONDED STYLUS
The benefit of conical styli, even if the cartridge is "lean", is the ball surface of the stylus touches the groove of vinyl records precisely.

Model AT-VM95C
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 20,000 Hz
Kanaltrennung 18 dB (1 kHz)
Kanalbalance am Ausgang 2.5 dB (1 kHz)
Ausgangsleistung 4.0 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Conical
Nadelabmessungen 0.6 mil
Schaftform der Nadel Bonded Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 17 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 6.5 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95C
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers

Der AT-VM95E ist das neue
Einstiegsmodell von Audio-Technica mit
elliptischer Nadel, das nicht nur den
legendären AT95E ersetzt, sondern auch
von den Entwicklungen des im Jahr 2015
eingeführten AT95EX profitiert.
Der AT-VM95E überzeugt durch ein
optimiertes, markantes Design mit steiferem,
resonanzarmem Gehäuse und – dank zwei
Gewindeeinsätzen im Gehäuse – eine
besonders einfache Montage mit nur zwei
Schrauben, ohne Muttern (mit Headshell oder
in den Tonarm integriert)

• Aluminium-Nadelträger
• Ausgangsspannung 4,0 mV
• Gehäuse kompatibel mit allen Abtastnadeln der Serie VM95
• Ersatz für AT95E und AT95EX
• Frequenzgang 20 bis 22.000 Hz

AT-VM95E
VM95 SERIES ELLIPTICAL STEREO CARTRIDGE
The AT-VM95E, the new Audio-Technica entry model Elliptical cartridge will replace the legendary AT95E and take advantage of the developments of the AT95EX introduced in 2015. The AT-VM95E features an improved and distinctive design resulting in a more rigid low resonance housing, and two threaded inserts in the cartridge body enabling it to be mounted to the headshell or on an integral tonearm with just two screws, no nuts.

Aluminium cantilever
4.0mV output voltage
Compatible body with all VM95 Series stylus assemblies
Replacement for AT95E and AT95EX
20 to 22,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

ELLIPTICAL BONDED STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

NO USE OF NUTS
VM95 Series cartridges features two M2.6 threaded inserts allowing the installation of the cartridge onto tonearm or removable headshell without the use of nuts.Each cartridge is provided with one pair of 8mm M2.6 screws, one pair of 11mm M2.6 screws and two plastic washers.

Model AT-VM95E
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 22,000 Hz
Kanaltrennung 20 dB (1 kHz)
Kanalbalance am Ausgang 2.0 dB (1 kHz)
Ausgangsleistung 4.0 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Elliptical
Nadelabmessungen 0.3 x 0.7 mil
Schaftform der Nadel Bonded Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 17 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 7 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95E
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers

Der AT-VM95E ist das neue
Einstiegsmodell von Audio-Technica mit
elliptischer Nadel, das nicht nur den
legendären AT95E ersetzt, sondern auch
von den Entwicklungen des im Jahr 2015
eingeführten AT95EX profitiert.
Der AT-VM95E überzeugt durch ein
optimiertes, markantes Design mit steiferem,
resonanzarmem Gehäuse und – dank zwei
Gewindeeinsätzen im Gehäuse – eine
besonders einfache Montage mit nur zwei
Schrauben, ohne Muttern (mit Headshell oder
in den Tonarm integriert)

• Das Tonabnehmer-Set AT-VM95E/H wird im Audio-TechnicaWerk
in Fukui (Japan) vormontiert, getestet und verpackt.
• Gesamtgewicht 15,5 g

AT-VM95E/H
VM95 SERIES ELLIPTICAL STEREO CARTRIDGE ON AT-HS6 HEADSHELL
AT-VM95E mounted on AT-HS6BK headshell
The total set weight is 15.5g
Assembled and tested in the Audio-Technica Factory in Fukui-Japan

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

ELLIPTICAL BONDED STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95E cartridge is fitted onto the 9g aluminiumdie cast body headshell

Model AT-VM95E/H
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 22,000 Hz
Kanaltrennung 20 dB (1 kHz)
Kanalbalance am Ausgang 2.0 dB (1 kHz)
Ausgangsleistung 4.0 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Elliptical
Nadelabmessungen 0.3 x 0.7 mil
Schaftform der Nadel Bonded Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 17 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 7 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 15.5 g
Abmessungen 21.2 × 21.4 × 62.4 ( H x W x D mm)
Ersatznadel AT-VMN95E

Der AT-VM95EN besitzt eine nackte,
elliptische Diamantnadel mit Rundschaft,
die aus einem Stück geschliffen und
direkt in den Nadelträger eingesetzt
wird. Auf diese Weise lässt sich ein
leichteres, steiferes Übertragungssystem
realisieren als mit einer gefassten
Diamantnadel mit Titan-Rundschaft wie
beim AT-VM95E. Die nackte
Diamantnadel ist zwar um einiges
kostspieliger, bietet aber auch eine
hörbar bessere Audioqualität mit
besonders hoher Klangtreue bei der
Höhenwiedergabe und hervorragendem
Impulsverhalten.

Aluminium-Nadelträger
• Ausgangsspannung 3,5 mV
• Gehäuse kompatibel mit allen Abtastnadeln der Serie VM95
• Frequenzgang 20 bis 23.000 Hz

AT-VM95EN
VM95 SERIES ELLIPTICAL NUDE STEREO CARTRIDGE
The AT-VM95EN, features a Nude Elliptical Diamond. The construction of the stylus being a one piece diamond with a round shank inserted in the cantilever creates a lighter and more rigid transmission system than a diamond tip bonded on a round titanium shank such as in the AT-VM95E. Also the use of nude diamond implies a substantial difference in pricing, yet the quality of the reproduction will be immediately noticed, specifically in the fidelity of high frequencies and in the quality of the transient responses.

Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 23,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

ELLIPTICAL NUDE STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

NO USE OF NUTS
VM95 Series cartridges features two M2.6 threaded inserts allowing the installation of the cartridge onto tonearm or removable headshell without the use of nuts.Each cartridge is provided with one pair of 8mm M2.6 screws, one pair of 11mm M2.6 screws and two plastic washers.

Model AT-VM95EN
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 23,000 Hz
Kanaltrennung 22 dB (1 kHz)
Kanalbalance am Ausgang 2.0 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Elliptical
Nadelabmessungen 0.3 x 0.7 mil
Schaftform der Nadel Nude Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 7 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95EN
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

AT-VM95EN vormontiert auf Headshell AT-HS6BK
• Das Tonabnehmer-Set AT-VM95EN/H wird im Audio-Technica Werk in Fukui (Japan) vormontiert, getestet und verpackt.
Gesamtgewicht 15,5 g

Der AT-VM95EN besitzt eine nackte,
elliptische Diamantnadel mit Rundschaft,
die aus einem Stück geschliffen und
direkt in den Nadelträger eingesetzt
wird. Auf diese Weise lässt sich ein
leichteres, steiferes Übertragungssystem
realisieren als mit einer gefassten
Diamantnadel mit Titan-Rundschaft wie
beim AT-VM95E. Die nackte
Diamantnadel ist zwar um einiges
kostspieliger, bietet aber auch eine
hörbar bessere Audioqualität mit
besonders hoher Klangtreue bei der
Höhenwiedergabe und hervorragendem
Impulsverhalten.

Aluminium-Nadelträger
• Ausgangsspannung 3,5 mV
• Gehäuse kompatibel mit allen Abtastnadeln der Serie VM95
• Frequenzgang 20 bis 23.000 Hz

AT-VM95EN
VM95 SERIES ELLIPTICAL NUDE STEREO CARTRIDGE
The AT-VM95EN, features a Nude Elliptical Diamond. The construction of the stylus being a one piece diamond with a round shank inserted in the cantilever creates a lighter and more rigid transmission system than a diamond tip bonded on a round titanium shank such as in the AT-VM95E. Also the use of nude diamond implies a substantial difference in pricing, yet the quality of the reproduction will be immediately noticed, specifically in the fidelity of high frequencies and in the quality of the transient responses.

Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 23,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

ELLIPTICAL NUDE STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95E cartridge is fitted onto the 9g aluminiumdie cast body headshell

Model AT-VM95EN
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 23,000 Hz
Kanaltrennung 22 dB (1 kHz)
Kanalbalance am Ausgang 2.0 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Elliptical
Nadelabmessungen 0.3 x 0.7 mil
Schaftform der Nadel Nude Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 7 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95EN
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

Der AT-VM95ML ist mit einem nackten
Microlinear-Diamanten ausgestattet, der
durch seinen speziellen Schliff und die für
Line-Contact-Nadeln typischen
geringeren Verzerrungen am Plattenende
(innere Rillen) eine doppelt so hohe
Lebensdauer gewährleistet und sich
zugleich durch einen erweiterten
Frequenzgang und eine bessere
Auflösung der mittleren und hohen
Frequenzen auszeichnet.

AT-VM95ML
VM95 SERIES MICROLINEAR STEREO CARTRIDGE
The AT-VM95ML, features a Nude Microlinear diamond, not only the Microlinear stylus will permit to double the duration of your stylus. The performance of a line contact stylus, will minimize the “inner groove distortion” as well as providing extended frequency response and maximize resolution in the medium and high frequencies of the audio program material.

material. Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 25,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

MICROLINEAR STYLUS
Microlinear profile diamond stylus offers high frequency response with less wear and distortion than elliptical or conventional linear contact styli.

NO USE OF NUTS
VM95 Series cartridges features two M2.6 threaded inserts allowing the installation of the cartridge onto tonearm or removable headshell without the use of nuts.Each cartridge is provided with one pair of 8mm M2.6 screws, one pair of 11mm M2.6 screws and two plastic washers.

Model AT-VM95ML
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 25,000 Hz
Kanaltrennung 23 dB (1 kHz)
Kanalbalance am Ausgang 1.5 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Microlinear
Nadelabmessungen 2.2 x 0.12 mil
Schaftform der Nadel Nude Square Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 10 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95ML
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

Der AT-VM95ML ist mit einem nackten
Microlinear-Diamanten ausgestattet, der
durch seinen speziellen Schliff und die für
Line-Contact-Nadeln typischen
geringeren Verzerrungen am Plattenende
(innere Rillen) eine doppelt so hohe
Lebensdauer gewährleistet und sich
zugleich durch einen erweiterten
Frequenzgang und eine bessere
Auflösung der mittleren und hohen
Frequenzen auszeichnet.

AT-VM95C/H
VM95 SERIES MICROLINEAR STEREO CARTRIDGE ON AT-HS6 HEADSHELL
AT-VM95ML mounted on AT-HS6BK headshell
The total set weight is 15.5g
Assembled and tested in the Audio-Technica Factory in Fukui-Japan

AT-VM95ML
VM95 SERIES MICROLINEAR STEREO CARTRIDGE
The AT-VM95ML, features a Nude Microlinear diamond, not only the Microlinear stylus will permit to double the duration of your stylus. The performance of a line contact stylus, will minimize the “inner groove distortion” as well as providing extended frequency response and maximize resolution in the medium and high frequencies of the audio program material.

material. Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 25,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

MICROLINEAR STYLUS
Microlinear profile diamond stylus offers high frequency response with less wear and distortion than elliptical or conventional linear contact styli.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95C cartridge is fitted onto the 9g aluminium die cast body headshell

Model AT-VM95ML
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 25,000 Hz
Kanaltrennung 23 dB (1 kHz)
Kanalbalance am Ausgang 1.5 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Microlinear
Nadelabmessungen 2.2 x 0.12 mil
Schaftform der Nadel Nude Square Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 10 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95ML
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

Der AT-VM95SH besitzt eine nackte
Shibata-Nadel – hochgeschätzt
insbesondere für audiophile HighendAnwendungen.
Der Shibata-Schliff ermöglicht satte,
volle Bässe und Mitten und einen
Frequenzgang bis 25.000 Hz.

AT-VM95SH
VM95 SERIES SHIBATA STEREO CARTRIDGE
The AT-VM95SH, features a Nude Shibata stylus, one of the most acclaimed stylus format by high end audiophiles. The Shibata stylus produces mid and bass sounds strong and rich in addition to offer a frequency response up to 25,000 Hz.

Aluminium cantilever
3.5mV output voltage
Compatible body with all VM95 Series stylus assemblies
20 to 25,000Hz frequency response

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

SHIBATA STYLUS
Provides a beautiful mid-high range Shibata-signature sound and strong mid-range volume.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95C cartridge is fitted onto the 9g aluminium die cast body headshell

Model AT-VM95SH
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 25,000 Hz
Kanaltrennung 23 dB (1 kHz)
Kanalbalance am Ausgang 1.5 dB (1 kHz)
Ausgangsleistung 3.5 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Microlinear
Nadelabmessungen 2.7 x 0.26mil
Schaftform der Nadel Nude Square Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 20 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 10 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95SH
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers
Non-magnetic screwdriver

AT-VMN95C
VM95 SERIES CONICAL REPLACEMENT STYLUS
Aluminium cantilever
Conical stylus
Bonded Round Shank

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

CONICAL BONDED STYLUS
The benefit of conical styli, even if the cartridge is "lean", is the ball surface of the stylus touches the groove of vinyl records precisely.

AT-VMN95E
VM95 SERIES ELLIPTICAL REPLACEMENT STYLUS
Aluminium cantilever
Elliptical stylus
Bonded Round Shank

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

ELLIPTICAL BONDED STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

Der AT-VM95EN besitzt eine nackte,
elliptische Diamantnadel mit Rundschaft,
die aus einem Stück geschliffen und
direkt in den Nadelträger eingesetzt
wird. Auf diese Weise lässt sich ein
leichteres, steiferes Übertragungssystem
realisieren als mit einer gefassten
Diamantnadel mit Titan-Rundschaft wie
beim AT-VM95E. Die nackte
Diamantnadel ist zwar um einiges
kostspieliger, bietet aber auch eine
hörbar bessere Audioqualität mit
besonders hoher Klangtreue bei der
Höhenwiedergabe und hervorragendem
Impulsverhalten.

AT-VMN95EN
VM95 SERIES ELLIPTICAL NUDE REPLACEMENT STYLUS
Aluminium cantilever
Elliptical Nude Stylus
Nude Round Shank

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

ELLIPTICAL NUDE STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

Der AT-VM95SH besitzt eine nackte
Shibata-Nadel – hochgeschätzt
insbesondere für audiophile HighendAnwendungen.
Der Shibata-Schliff ermöglicht satte,
volle Bässe und Mitten und einen
Frequenzgang bis 25.000 Hz.

AT-VMN95SH
VM95 SERIES SHIBATA REPLACEMENT STYLUS
Aluminium cantilever
Shibata Stylus
Nude Square Shank

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

SHIBATA STYLUS
Provides a beautiful mid-high range Shibata-signature sound and strong mid-range volume.

AT-XP3
Dual Moving Magnet Stereo Cartridge
The AT-XP series cartridges provide a high quality sound for vinyl DJ’s. Offering all of the features of a DJ cartridge, but with a Hi-fi sound, the XP series are perfect for the stage and club DJ who prioritises sound quality.

• Audiophile DJ cartridge equipped with a conical stylus
• VM dual magnet construction
• Durable robust design for high-quality specialist DJ playback
• Signal output level and output impedance characteristics suited for professional DJ applications
• Carbon fiber-reinforced ABS cantilever and nylon wire suspension ensure precise tracking
• Compatible with the replacement styli ATN-XP5 and ATN-XP7 for an upgrade

Specifications:
• Model AT-XP3
• Mounting Half-inch
• Frequency Response 20 to 18,000 Hz
• Channel Separation 20 dB (1 kHz)
• Output Channel Balance 2.0 dB (1 kHz)
• Output Voltage 5.5 mV (at 1 kHz, 5 cm/sec)
• Vertical Tracking Angle 20 degrees
• Vertical Tracking Force Range 2.0 to 4.0g (standard 3.0 g)
• Stylus Shape Conical
• Stylus Size 0.6 mil
• Stylus Construction Bonded Round Shank
• Cantilever Carbon reinforced ABS
• Coil Impedance 6,700 ohms (1 kHz)
• Coil Inductance 550 mH (1 kHz)
• Static Compliance 20 x 10 – 6 cm / dyne
• Dynamic Compliance 6.0 x 10 – 6 cm / dyne (100 Hz)
• Recommended Load Impedance 47,000 Ω
• Recommended Load Capacitance 100-200 pF
• Cartridge Weight 6.2g
• Dimensions 17.2 x 17.8 x 28.3 ( H x W x D mm)
• Replacement Stylus ATN-XP3
• Accessories Included Two 11 mm installation screws, Two 8 mm installation screws, Two washers, Two Nut, Non-magnetic screwdriver

manual: https://eu.audio-technica.com/resources/AT-XP3_UM_112301371_V1_11L_web_180620.pdf

ATN-XP3
Replacement Stylus for AT-XP3
Conical Bonded Stylus
Carbon fibre-reinforced ABS cantilever
Durable design for DJ application

Clearaudio’s V2 MM technology uses ebony as a resonanceresistant body. Other ingredients of the recipe for success are the most effective reduction of moving mass, an optimised polishing technique for the stylus and highly effective cartridge damping. This is precision engineering in the pursuit of the best sound.

The Clearaudio V2 moving magnet cartridges are meticulously measured, analysed, and hand-selected into four Performance levels. In this way Clearaudio achieves the best stereo channel
matching, minimum phase error and distortion, flattest frequency response and highest dynamic range at each price point. The cartridges produce an audiophile sound of superlative quality – spatially detailed and vividly textured, with bass that does not wallow and treble that is not harsh.

The models of the Clearaudio MM V2 series provide outstanding sound quality on all current tonearms. With the exception of the MM V2 Concept, which is made of aluminium, all the cartridges in this series are made with housings of hand-polished ebony – the key to record-breaking weight values. The Performer V2 weighs just 7.4 grams, the Artist V2 8.4 grams. This is what Clearaudio calls ‘effective reduction of the moving mass’.

FEATURES
Technical Specifications:
• TOTAL MASS 8.6g (± 0.2g)
• FREQUENCY RESPONSE 20Hz - 20kHz
• OUTPUT VOLTAGE (1KHZ, 5CM/S) ~ 3.3mV
• CHANNEL SEPARATION (1KHZ) 20dB
• CHANNEL BALANCE (1KHZ) 2dB
• TRACKING ABILITY 80μm
• RECOMMENDED TRACKING FORCE 2.2g ± 0.3g
• COIL IMPEDANCE (1KHZ) 0.66kΩ
• COIL INDUCTANCE 400mH
• LOAD RESISTANCE 47kΩ
• LOAD CAPACITANCE 100pF
• CANTILEVER / STYLUS SHAPE Aluminium / elliptical
• COMPLIANCE 15μ/mN
• CARTRIDGE BODY Aluminium
• MANUFACTURER’S WARRANTY 2 years

Manual: https://clearaudio.de/_assets/_pdf/manuals/cartridges/CA_MM%20V2_E+D.pdf?d=1653493472

Level Gauge - Basic
High precision gauge, calibrated.

Level Gauge - Stainless steel
High precision gauge, calibrated.

Tonearm gauge
The easiest way to adjust the cartridge's Tracking Force.

Every once and a while you need to take care of your record player. This is the NP5 diamond stylus replacement needle which is compatible for these record player:
• Mercury
• C62 Black
• T150
• C6 White

Specifications:
• ABS Plastic Composition
• Diamond Stylus Needle
• Plays 3 Speeds (33 1/3, 45 and 78 RPM)

Stylus for Goldring G1006 Cartridge

Just needle, not the complete cartridge included!

Goldring E1

The Goldring philosophy is to promote the accurate replication of the original record production, maintaining the creative nuances, musicality and rhythm the artist intended you to hear. With the versatile E Series, this is easy to achieve; each is designed to be simple to fit to the majority of budget to medium priced turntables.

The E1 cartridge, the first in the range, utilises a carbon-fibre reinforced cantilever and bonded, spherical (0.6 mil) stylus with a round shank. Carbon is an effective alternative to more premium aluminium or boron materials, producing comparable results in most entry level hi-fi applications.

Magnetic Duplex Technology™
All cartridges in the range feature Magnetic Duplex Technology™-a 'dual magnet' generator assembly with an identical geometry to that of the original cutting head. This means it can more accurately reproduce the stereo information in the record groove, providing better channel separation and a more involving and musical sound stage.

Expert Adjustment
The E-series cartridges have been designed to allow micro-adjustments to be made during production using a special adjustment screw. This means the cartridge can be safely installed in a typical turntable because the angle that the stylus makes with the record surface has been pre-set. The result is an optimised channel balance with zero degrees of horizontal tracking adjustment required. This ensures a consistent and reassuring performance for the life of the product.

Stylus/Cantilever
Featuring spherical styli with a choice of cantilevers, the E1 and E2 models are ideal as an upgrade to any budget, pre-fitted or obsolete cartridge. The E3 model with its re­fined super elliptical stylus is a worthwhile upgrade for those wishing to squeeze even more information and detail from the record groove.

• Colour: Red
• Cantilever: Carbon
• Stylus profile: Spherical
• Stylus radius: 0.6 mil
• Frequency range: 20 Hz - 20 kHz
• Channel balance: 1.5 dB at 1 kHz
• Channel separation: >20 dB at 1 kHz
• Sensitivity: 3.5 mV (1 kHz @ 5 cm/sec)
• Static compliance: 20 mm/N
• Vertical tracking angle: 20°
• Load resistance: 47 kΩ
• Load capacitance: 100 - 200 pF
• Internal inductance: 400 mH
• Internal resistance: 410 Ω
• Cartridge mass: 6.9 g
• Fixing centres: 12.7 mm (0.5 in)
• Playing weight: 1.5 g - 2.5 g (2.0 g recommended)

Stylus for Goldring E1 MM Cartridge

Goldring E2

The Goldring philosophy is to promote the accurate replication of the original record production, maintaining the creative nuances, musicality and rhythm the artist intended you to hear. With the versatile E Series, this is easy to achieve; each is designed to be simple to fit to the majority of budget to medium priced turntables.

The E2 cartridge, the middle in the range, features the same spherical stylus profile as the E1 but with the additional benefit of an upgraded aluminium cantilever. This is both stiff and light weight allowing the stylus to more accurately trace medium to high frequencies offering more detail and reducing distortion and mis-tracking during loud passages.

Magnetic Duplex Technology™
All cartridges in the range feature Magnetic Duplex Technology™-a 'dual magnet' generator assembly with an identical geometry to that of the original cutting head. This means it can more accurately reproduce the stereo information in the record groove, providing better channel separation and a more involving and musical sound stage.

Expert Adjustment
The E-series cartridges have been designed to allow micro-adjustments to be made during production using a special adjustment screw. This means the cartridge can be safely installed in a typical turntable because the angle that the stylus makes with the record surface has been pre-set. The result is an optimised channel balance with zero degrees of horizontal tracking adjustment required. This ensures a consistent and reassuring performance for the life of the product.

Stylus/Cantilever
Featuring spherical styli with a choice of cantilevers, the E1 and E2 models are ideal as an upgrade to any budget, pre-fitted or obsolete cartridge. The E3 model with its re­fined super elliptical stylus is a worthwhile upgrade for those wishing to squeeze even more information and detail from the record groove.

• Colour: Green
• Cantilever: Aluminium
• Stylus profile: Spherical
• Stylus radius: 0.6 mil
• Frequency range: 20 Hz - 20 kHz
• Channel balance: 1.5 dB at 1 kHz
• Channel separation: >20 dB at 1 kHz
• Sensitivity: 3.5 mV (1 kHz @ 5 cm/sec)
• Static compliance: 20 mm/N
• Vertical tracking angle: 20°
• Load resistance: 47 kΩ
• Load capacitance: 100 - 200 pF
• Internal inductance: 400 mH
• Internal resistance: 410 Ω
• Cartridge mass: 6.9 g
• Fixing centres: 12.7 mm (0.5 in)
• Playing weight: 1.5 g - 2.5 g (2.0 g recommended)

Stylus for Goldring E2 MM Cartridge

Goldring E3

The Goldring philosophy is to promote the accurate replication of the original record production, maintaining the creative nuances, musicality and rhythm the artist intended you to hear. With the versatile E Series, this is easy to achieve; each is designed to be simple to fit to the majority of budget to medium priced turntables.

The E3 cartridge, representing the top of the range features the same aluminium cantilever as the E2, but benefits from a superior, bonded, super-elliptical (0.3 x 0.7 mil) stylus. This gives it better high frequency detail retrieval over ordinary elliptical (0.4 x 0.7 mil) or spherical (0.6 mil) types due to its smaller front-to-back radius. The main effect is the reduction of sibilance, especially in high level vocal recordings

Magnetic Duplex Technology™
All cartridges in the range feature Magnetic Duplex Technology™-a 'dual magnet' generator assembly with an identical geometry to that of the original cutting head. This means it can more accurately reproduce the stereo information in the record groove, providing better channel separation and a more involving and musical sound stage.

Expert Adjustment
The E-series cartridges have been designed to allow micro-adjustments to be made during production using a special adjustment screw. This means the cartridge can be safely installed in a typical turntable because the angle that the stylus makes with the record surface has been pre-set. The result is an optimised channel balance with zero degrees of horizontal tracking adjustment required. This ensures a consistent and reassuring performance for the life of the product.

Stylus/Cantilever
Featuring spherical styli with a choice of cantilevers, the E1 and E2 models are ideal as an upgrade to any budget, pre-fitted or obsolete cartridge. The E3 model with its re­fined super elliptical stylus is a worthwhile upgrade for those wishing to squeeze even more information and detail from the record groove.

• Colour: Violet
• Cantilever: Aluminium
• Stylus profile: Elliptical
• Stylus radius: 0.3 x 0.7 mil
• Frequency range: 20 Hz - 20 kHz
• Channel balance: 1.5 dB at 1 kHz
• Channel separation: >20 dB at 1 kHz
• Sensitivity: 3.5 mV (1 kHz @ 5 cm/sec)
• Static compliance: 20 mm/N
• Vertical tracking angle: 20°
• Load resistance: 47 kΩ
• Load capacitance: 100 - 200 pF
• Internal inductance: 400 mH
• Internal resistance: 410 Ω
• Cartridge mass: 6.9 g
• Fixing centres: 12.7 mm (0.5 in)
• Playing weight: 1.5 g - 2.5 g (2.0 g recommended)

Stylus for Goldring E4 MM Cartridge

Just needle, not the complete cartridge included!

The Goldring 1006 is designed for owners who want to get the very best from their systems at a budget price. This cartridge has an elliptical tip for improved high frequency clarity and a powerful magnet to ensure high sensitivity.

This hand-built cartridge features an elliptical stylus; its shape enables it to more accurately trace the highest frequency record grooves giving it the advantage over ordinary spherical types. The lightweight shank also gives the stylus a lower tip mass than cheaper metal bonded types lending the cartridge an improved transient response.

Low Mass Pocan® Body
The 1000 series uses a strong one piece body which holds the fixed parts securely in place. Made from a special type of ultra-rigid, glass reinforced polyester called Pocan, the body can be tightly bolted to the head shell for maximum efficiency and optimum sound quality. The user replaceable stylus carrier slots tightly into the body with a locating pin preventing unwanted vibrations which would otherwise colour the sound. An integral mu-metal can keeps the generator parts shielded from hum-inducing stray magnetic fields. Because Pocan has a high strength-to-mass ratio, the overall mass of the G1000 series cartridges is kept below 6.5 g. Low mass and moderate compliance keep the natural arm/cartridge resonance within safe limits for easy matching to a wide range of tonearms.

High Efficiency Magnetic Circuit
Finely etched mu-metal is laminated to form the pole pieces around which are fitted two formerless coils of four thousand turns each. This unique design reduces mass and also makes for a very efficient magnetic circuit producing a higher than average output. This construction also reduces the loss at high frequencies inherent in conventional designs, making for a smooth and extended frequency response.

Reduced Moving Mass
The 1000 series uses a unique ultra-low-mass, micro-miniature Alnico V magnet made to a tolerance that can be achieved by no other manufacturer worldwide. Welded to the magnet is a gold plated nickel tie-bar which provides an earth path for vinyl static charge build up and stabilses the cantilever in unwanted vibrational modes. The whole ultra-low-mass assembly is then mounted in a special butyl rubber polymer with optimised damping characteristics.

Expert Adjustment
The correct setting of stylus azimuth (or horizontal tracking angle) is essential for the maintenance of a proper stereo sound stage. Azimuth is the term used to describe the angle that the vertical centre-line of the stylus makes with the record surface and this must be exactly perpendicular to the record groove. This is not usually a user adjustable parameter on most budget decks and so it is vital that the cartridge leaves the factory with the azimuth precisely set. Badly adjusted azimuth can cause uneven channel balance and increased crosstalk between channels which would severely degrade the stereo image.

Specifications:
• Frequency Response: 20 Hz -20 kHz ±3 dB
• Channel Balance: within 2 dB @ 1 kHz
• Channel Separation: better than 25 dB @ 1 kHz
• Sensitivity: 6.5 mV ±1.5 dB, 1 kHz @ 5 cm/sec
• Static Compliance: 24 mm/N (lat); 16 mm/N (vert)
• Equivalent tip mass: 0.45 mg
• Vertical Tracking Angle: 24°
• Stylus Radius: Elliptical
• Stylus Type: Replaceable
• Load Resistance: 47 kΩ
• Load Capacitance: 150-200 pF
• Internal Inductance: 570 mH
• Internal Resistance: 660 Ω
• Cartridge Mass: 6.3 g
• Cartridge Mass (inc. fixings): 7.6 g
• Fixing Centre: 0.5" (12.7 mm)
• Playing Weight: 1.5 - 2.0 g (1.7 g nom.)
• Replacement Stylus: 1006 - D0

DJ-03 HD - CARTRIDGE INCL. HEADSHELL

This is the Nagaoka DJ cartridge. With a high output voltage of 6 mV and a recommended tracking force of 3 - 5 g, it is one of the more stable of its kind.

TECHNICAL SPECIFICATIONS:
• Cartridge type: MM
• Configuration: Climax DS/DSM
• Output voltage: 6 mV (5 cm/sec.)
• Frequency Characteristics: 20Hz~20KHz
• Channel separation: 20 dB (1 kHz)
• Channel balance: 2 dB or less
• Load resistance: 47 kΩ
• Load: 100pF
• Cantilever: aluminum alloy
• Needle Tip: 0.6 mil tapered bonded diamond
• Recommended tracking force: 3~5g
• Pickup weight: 5.1g
• Weight with headshell: 15.1g

Replacement stylus for Shure M44G.

This product is a NAGAOKA produced and manufactured replacement stylus for the M44G, a cartridge widely used by DJs around the world. We have received many inquiries about a replacement stylus compatible with the M44G, since we had 'GD63-44G' in our lineup. After the production of 'GD63-44G' was discontinued, we reviewed the specifications and developed a new model. The new DJ-44G has a high sound pressure, delicate, wide-range, and powerful sound while keeping main features of toughness and solidity from the original M44G replacement.

Technical data
• Vertical tracking force: 2.0-3.5 g
• Material Cantilever: Aluminum alloy
• Material Stylus tip: 0.6 mil spherical bonded diamond
• Compatible cartridge: M44G/M44-7

Replacement stylus Nagaoka G JN-03D for the pickup DJ-03HD.

Nagaoka Headshell HSAL-01

This headshell has been designed with the utmost precision to give you an outstanding listening experience.

Design for maximum ease of use:
When placing the needle, the finger lift design provides an excellent view of the needle tip. The finger hook is easy to use and the angle can be easily held with your fingers. Every detail has been designed with the utmost care to ensure uncomplicated and pleasant use.

Ideal for NAGAOKA JT-80 Series and many other pickups:
This high-quality headshell was developed specifically for the NAGAOKA JT-80 series to ensure an optimal combination of precision and performance. Enjoy music in its purest form with this perfectly coordinated combination.

Of course, the Nagaoka HSAL-01 can also be combined with other pickups. The elongated holes allow the perfect positioning of your pickup and the included cables leave enough room for adjustment.

Easy installation:
The Nagaoka Headshell HSAL-01 comes with an installation guide to give you an effortless setup. The package contains all the necessary items including mounting screws to make the installation process easier for you.

Product specifications:
• Housing material: aluminum
• Pin: Gold plated
• Weight: 6.8g (approximate value, excluding mounting screws)
• Frequency response: 20Hz - 20kHz
• Box contents: headshell housing, lead wire, 2 × 12mm screws, 2 × 6mm screws, compatible nuts, washers.

Replacement stylus for Nagaoka MP-100.

To exchange the needle of the MP 100, simply pull off the needle carrier of the system and replace it with the JN-P 100.

Replacement stylus for Nagaoka MP-110.

To exchange the needle of the MP 110, simply pull off the needle carrier of the system and replace it with the JN-P 110.

Replacement stylus for Nagaoka MP-150.

To exchange the needle of the MP 150, simply pull off the needle carrier of the system and replace it with the JN-P 150.

The Nagaoka JT-80LB (Lapis Blue) cartridge with its shiny blue needle insert is the basic model of the series and features an aluminium needle carrier with a set diamond. With its open, powerful sound, it offers exceptional value for money. The cartridge unfolds its full potential after an approx. 80-hour play-in period.

TECHNICAL SPECIFICATIONS:
• Format: Moving magnet type (MM type)
• Output: 5.0 mV (5 cm / sec)
• Frequency characteristic: 20Hz-20,000Hz
• Channel separation: 23dB (1Khz)
• Channel balance: 1.5 dB or less
• Cantilever: Aluminum alloy
• Needle tip: 0.4x0.7mil Ellipse / Joined diamond
• Stylus pressure: 1.3g-1.8g
• Torridge own weight: 6.9g
• Replacement needle: JTS-80LB
• Cartridge type: without head shell

https://www.auditorium.de/attachment/STEREO_3-21_Nagaoka-Abtaster_englisch.pdf

Replacement stylus Nagaoka JTS-80LB for the pickup JT-80LB.

With its round diamond, the MP-100 cartridge is particularly suitable for older records. Even scratches and dirt do not affect the pleasant, neutral sound that this system makes possible. The MP-100 is the most affordable scanner in the MP range.

TECHNICAL SPECIFICATIONS:
• Principle: MI - High Output (for the MM input)
• Weight: 6.5g
• Height 18mm
• Needle cut: Round 0.6mm
• Cantilever: aluminum
• Frequency response: 20 - 20,000 Hz
• Output Voltage (1kHz, 5cm/sec): 5.0mV
• Channel separation (1kHz): > 22 dB
• Channel balance (1kHz): < 2.0 dB
• Needle compliance: 19 µm/mN
• Recommended tracking force: 21 mN (18-23 mN)
• Recommended termination resistance: 47 kOhm
• Recommended termination capacity: 150 – 200 pF
• Replacement needle: JN-P100
• Cartridge type: without head shell

Hear the vivid sound experience that music playback offers with Nagaoka's MP-110 tonearm. Especially in the high-frequency range, the elliptical needle cut ensures better detail resolution. This creates a live atmosphere while listening, which is otherwise known from concerts.

TECHNICAL SPECIFICATIONS:
• Principle: MI - High Output (for the MM input)
• Weight: 6.5g
• Height: 18mm
• Needle cut: Elliptical 0.4x0.7
• Cantilever: aluminum
• Frequency response: 20 - 20,000 Hz
• Output Voltage (1kHz, 5cm/sec): 5.0mV
• Channel Separation (1kHz): >23dB
• Channel balance (1kHz): < 1.5 dB
• Needle compliance: 19 µm/mN
• Recommended tracking force: 18 mN (15-20 mN)
• Recommended termination resistance: 47 kOhm
• Recommended termination capacity: 150 – 200 pF
• Replacement needle: JN-P110
• Cartridge type: without head shell

The design of the MP-150 has been significantly refined. Higher quality magnet materials, a better cantilever and a bonded diamond ensure better tracking and detail reproduction. The bass range also sounds more balanced.

TECHNICAL SPECIFICATIONS:
• Principle: MI - High Output (for the MM input)
• Weight: 6.5g
• Height: 18mm
• Needle cut: Elliptical 0.4x0.7mm
• Needle carrier: stiffened cone aluminum tube
• Frequency response: 20 - 20,000 Hz
• Output voltage (1kHz, 5cm/sec): 4.5mV
• Channel separation (1kHz): > 24 dB
• Channel balance (1kHz): < 1.5 dB
• Needle compliance: 20 µm/mN
• Recommended tracking force: 18 mN (15-20 mN)
• Recommended termination resistance: 47 kOhm
• Recommended termination capacity: 150 – 200 pF
• Replacement needle: JN-P150
• Cartridge type: without head shell

The 2M 78 features an improved engine, which provides a high level of sonic accuracy. The stylus' tip is a Spherical diamond that is perfect for playback of 78 rpm shellac records, which require a larger stylus profile. The cartridge body is manufactured from Hopelex, which ensures high rigidity while eliminating unwanted resonances.

2M 78 uses a strapped output to deliver the same output signal from both sets of pole pins. This effectively eliminates the need for mono-specific equipment, making it possible to enjoy true mono reproduction on any stereo playback system.

The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M 78 Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4 mV
• Frequency response - 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 70 µm
• Compliance, dynamic, lateral - 18 µm/mN
• Stylus type - Spherical
• Stylus tip radius - R 65 µm
• Tracking force range - 1.6-2.0g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Internal impedance, DC resistance - 700 Ohm
• Internal inductance - 350 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Tracking angle - 20°
• Cartridge colour, body/stylus - Black/Grey
• Cartridge weight without screws - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M 78 (interchangeable with 2M Mono)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

Next level authenticity with the 2M Blue
The goal for any cartridge should be to reproduce the sound as close to the artists vision as possible, and the 2M blue takes you further on this journey of authenticity. With the 2M Blue, you get serious about listening to vinyl.

Features:
The 2M Blue features a Nude Elliptical diamond and split pole pins with a copper wire.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

The 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details compared to the 2M Red model.

2M Blue Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 25 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 2 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Nude Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Blue
• Cartridge weight - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M Blue (interchangeable with 2M Red and 2M Silver)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze, 2M Black and 2M Black LVB 250
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

With the 2M Premounted, it’s never been easier to experience
The 2M Premounted is a practical and elegant solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm. The quality of the SH-4 headshell is sturdy and rigid, yet the design emphasizes a slim and delicate form factor. The strong, lightweight headshell has an ergonomic design with a long finger lift that is easy to pick up.

Features:
- Premounted on our popular SH-4 Black headshell.
- Easy and direct mount on S-shaped tonearms with universal mount.
- Correct Baerwald alignment with tonearms with universal mount.

The 2M Series is developed in conjunction with the Danish Industrial designer Møller Jensen Design – the same designer who designed the award winning MC Jubilee and Kontrapunkt series. Inspired by the facets of a diamond, whose contours gracefully trace the grooves on a record’s surface, the 2M’s handsome elegance establishes a great combination of form and functionality.

The name 2M was selected from among several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.

Of course the 2M isn’t just another pretty face. It has been engineered to the highest standards and is congruent with Ortofon’s unrelenting commitment to providing the most precise and accurate reproduction possible without coloration.

The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Bronze features:

The 2M Bronze features a Nude Fine Line diamond, which is particularly suited for demanding applications. The slim profile of the Fine Line stylus will track even the highest frequency information, making it a must for discerning listeners. Additionally, its larger footprint ensures reduced distortion and record wear.

The cartridge body is manufactured from Hopelex, a material which ensures high rigidity while eliminating unwanted resonances. The 2M Bronze uses a special upgraded engine, featuring split pole pins with a silver plated copper wire.

Output voltage at 1000 Hz, 5cm/sec. - 5 mV
Channel balance at 1 kHz - 1 dB
Channel separation at 1 kHz - 26 dB
Channel separation at 15 kHz - 15 dB
Frequency response - 20-20.000 + 2 / - 0 dB
Tracking ability at 315Hz at recommended tracking force - 80 µm
Compliance, dynamic, lateral - 22 µm/mN
Stylus type - Nude Fine Line
Stylus tip radius - r/R 8/40 µm
Tracking force range - 1.4-1.7 g (14-17 mN)
Tracking force, recommended - 1.5 g (15 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1.2 kOhm
Internal inductance - 630 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 150-300 pF
Cartridge colour, body/stylus - Black/Bronze
Cartridge weight - 7.2 g
Replacement stylus unit - 2M Bronze (interchangeable with 2M Black and 2M Black LVB 250)

Each of the 2M Series cartridges has its own individual sonic expression, and all five models together represent the ensemble of five classic variations:

• 2M Mono SE, 2M Mono and 2M 78 are a true mono cartridges for playing mono vinyl records
• 2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth
• 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details
• 2M Bronze adds even more details and resolution but in a very evenhanded way that pays respect to all elements
• 2M Black is the best of everything, true to the groove with resolution and accurate insight into each recording

Bona fide precision with the 2M Bronze
To us hi-fi is more than a fancy label. High fidelity is the goal of everything we do. The 2M Bronze is designed to give the music a whole new dimension of precision. Listening to your records with the 2M Bronze is like hearing them for the first time and you get to fall in love with the songs all over. That is what hi-fi means to us and that is what you get with the 2M Bronze.

Features:
The 2M Bronze features a Nude Fine Line diamond, which is particularly suited for demanding applications. The slim profile of the Fine Line stylus will track even the highest frequency information. Additionally, its larger footprint ensures reduced distortion and record wear. The 2M Bronze uses a special upgraded engine, featuring split pole pins with a silver plated copper wire.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Bronze Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5 mV
• Channel balance at 1 kHz - 1 dB
• Channel separation at 1 kHz - 26 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 + 2 / - 0 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 22 µm/mN
• Stylus type - Nude Fine Line
• Stylus tip radius - r/R 8/40 µm
• Tracking force range - 1.4-1.7 g (14-17 mN)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.2 kOhm
• Internal inductance - 630 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Bronze
• Cartridge weight - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M Bronze (interchangeable with 2M Black and 2M Black LVB 250)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze, 2M Black and 2m Black LVB 250
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

With the 2M Premounted, it’s never been easier to experience
The 2M Premounted is a practical and elegant solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm. The quality of the SH-4 headshell is sturdy and rigid, yet the design emphasizes a slim and delicate form factor. The strong, lightweight headshell has an ergonomic design with a long finger lift that is easy to pick up.

Features:
- Premounted on our popular SH-4 Black headshell.
- Easy and direct mount on S-shaped tonearms with universal mount.
- Correct Baerwald alignment with tonearms with universal mount.

The 2M Series is developed in conjunction with the Danish Industrial designer Møller Jensen Design – the same designer who designed the award winning MC Jubilee and Kontrapunkt series. Inspired by the facets of a diamond, whose contours gracefully trace the grooves on a record’s surface, the 2M’s handsome elegance establishes a great combination of form and functionality.

The name 2M was selected from among several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.

Of course the 2M isn’t just another pretty face. It has been engineered to the highest standards and is congruent with Ortofon’s unrelenting commitment to providing the most precise and accurate reproduction possible without coloration.

The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Bronze features:

The 2M Bronze features a Nude Fine Line diamond, which is particularly suited for demanding applications. The slim profile of the Fine Line stylus will track even the highest frequency information, making it a must for discerning listeners. Additionally, its larger footprint ensures reduced distortion and record wear.

The cartridge body is manufactured from Hopelex, a material which ensures high rigidity while eliminating unwanted resonances. The 2M Bronze uses a special upgraded engine, featuring split pole pins with a silver plated copper wire.

Output voltage at 1000 Hz, 5cm/sec. - 5 mV
Channel balance at 1 kHz - 1 dB
Channel separation at 1 kHz - 26 dB
Channel separation at 15 kHz - 15 dB
Frequency response - 20-20.000 + 2 / - 0 dB
Tracking ability at 315Hz at recommended tracking force - 80 µm
Compliance, dynamic, lateral - 22 µm/mN
Stylus type - Nude Fine Line
Stylus tip radius - r/R 8/40 µm
Tracking force range - 1.4-1.7 g (14-17 mN)
Tracking force, recommended - 1.5 g (15 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1.2 kOhm
Internal inductance - 630 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 150-300 pF
Cartridge colour, body/stylus - Black/Bronze
Cartridge weight - 7.2 g
Replacement stylus unit - 2M Bronze (interchangeable with 2M Black and 2M Black LVB 250)

Each of the 2M Series cartridges has its own individual sonic expression, and all five models together represent the ensemble of five classic variations:

• 2M Mono SE, 2M Mono and 2M 78 are a true mono cartridges for playing mono vinyl records
• 2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth
• 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details
• 2M Bronze adds even more details and resolution but in a very evenhanded way that pays respect to all elements
• 2M Black is the best of everything, true to the groove with resolution and accurate insight into each recording

Step into the music with the 2M Red
With the 2M Red you will hear the music come to life on its own terms. It is like taking a step into music itself. This is our entry-level cartridge in the series, but what an entry.

Featues:
The 2M Red features a tipped Elliptical diamond and split pole pins with a copper wire.
The engine provides an increased output of 5.5 mV and an optimized sound reproduction and a high level of sonic accuracy.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Red delivers an open, dynamic sound with a slight touch of warmth.

2M Red Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 22 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 70 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Red
• 2M standard and 2M Verso cartridges weight - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M Red (interchangeable with 2M Blue and 2M Silver)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze, 2M Black and 2M Black LVB 250
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

With the 2M Premounted, it’s never been easier to experience.
The 2M Premounted is a practical and elegant solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm. The quality of the SH-4 headshell is sturdy and rigid, yet the design emphasizes a slim and delicate form factor. The strong, lightweight headshell has an ergonomic design with a long finger lift that is easy to pick up.

Features:
- Premounted on our popular SH-4 Black headshell.
- Easy and direct mount on S-shaped tonearms with universal mount.
- Correct Baerwald alignment with tonearms with universal mount.

2MR: the newest addition to the renowned 2M Series
Ortofon 2MR features a specially designed cartridge housing tailored for turntables and tonearms like Rega matching their requirement for low-form factor cartridges. With its narrow cartridge housing, it seamlessly integrates without a need for modifications or spacers under the tonearm, enabling quick and easy mounting with just two screws. Ortofon 2MR cartridges features unique to Ortofon technologies like: High-performance quad coil motor system with split pole pins, Proprietary Ortofon premium and high-end rubber dampers plus full compatibility with the Ortofon 2M series styli.

Authentic sound reproduction
2MR continues the 2M Series' commitment to authentic sound reproduction.
A high-performance motor system featuring quad coils and split pole pins minimizes eddy current losses, enhancing channel balance and accuracy.
This innovation results in a clean, detailed, and true-to-life sound, faithfully capturing the nuances of your cherished vinyl collection.

More than just a cartridge
2MR cartridge are for those who value an authentic immersive listening experience when listening to their music. 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.
The 2MR maintains the hallmark of interchangeability, allowing you to explore your records in greater depth and detail. The seamless transition between stylus profiles lets you tailor your listening experience, ensuring every note is heard with unparalleled accuracy and emotion. The 2MR series empowers you to explore your records like never before, allowing you to savor every moment of your favorite music.
The 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.

2MR cartridge key features:
• Slimline cartridge body effectively eliminates the need for tonearm spacers, shims or modifications on turntables needing a low form factor cartridge.
• High-performance motor system incorporating unique to Ortofon quad coils with split pole pins, delivering a clean detailed and true-to-life sound.
• 100% compatibility with the 2M styli Ortofon 2MR use the well-known 2M styli.
• Standard half inch mounting quick and easy mounting on the tonearms with just two screws.
• Full range setup 2MR ranges from Mono to Premium: 2MR Red to High-end: 2MR Black LVB 250

Next level authenticity with the 2M Blue
The goal for any cartridge should be to reproduce the sound as close to the artists vision as possible, and the 2M blue takes you further on this journey of authenticity. With the 2M Blue, you get serious about listening to vinyl.

Features:
The 2M Blue features a Nude Elliptical diamond and split pole pins with a copper wire.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

The 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details compared to the 2M Red model.

Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 25 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 2 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Nude Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Blue
• 2MR cartridge weight - 6 g
• 2M and 2M Verso cartridges weight - 7.2 g
• 2M Premounted cartridge weight - 16.7 g

Replacement stylus unit - 2M Blue (interchangeable with 2M Red and 2M Silver)

Stylus lifetime:
with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

2MR: the newest addition to the renowned 2M Series
Ortofon 2MR features a specially designed cartridge housing tailored for turntables and tonearms like Rega matching their requirement for low-form factor cartridges. With its narrow cartridge housing, it seamlessly integrates without a need for modifications or spacers under the tonearm, enabling quick and easy mounting with just two screws. Ortofon 2MR cartridges features unique to Ortofon technologies like: High-performance quad coil motor system with split pole pins, Proprietary Ortofon premium and high-end rubber dampers plus full compatibility with the Ortofon 2M series styli.

Authentic sound reproduction
2MR continues the 2M Series' commitment to authentic sound reproduction.
A high-performance motor system featuring quad coils and split pole pins minimizes eddy current losses, enhancing channel balance and accuracy.
This innovation results in a clean, detailed, and true-to-life sound, faithfully capturing the nuances of your cherished vinyl collection.

More than just a cartridge
2MR cartridge are for those who value an authentic immersive listening experience when listening to their music. 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.
The 2MR maintains the hallmark of interchangeability, allowing you to explore your records in greater depth and detail. The seamless transition between stylus profiles lets you tailor your listening experience, ensuring every note is heard with unparalleled accuracy and emotion. The 2MR series empowers you to explore your records like never before, allowing you to savor every moment of your favorite music.
The 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.

2MR cartridge key features:
• Slimline cartridge body effectively eliminates the need for tonearm spacers, shims or modifications on turntables needing a low form factor cartridge.
• High-performance motor system incorporating unique to Ortofon quad coils with split pole pins, delivering a clean detailed and true-to-life sound.
• 100% compatibility with the 2M styli Ortofon 2MR use the well-known 2M styli.
• Standard half inch mounting quick and easy mounting on the tonearms with just two screws.
• Full range setup 2MR ranges from Mono to Premium: 2MR Red to High-end: 2MR Black LVB 250

Bona fide precision with the 2M Bronze
To us hi-fi is more than a fancy label. High fidelity is the goal of everything we do. The 2M Bronze is designed to give the music a whole new dimension of precision. Listening to your records with the 2M Bronze is like hearing them for the first time and you get to fall in love with the songs all over. That is what hi-fi means to us and that is what you get with the 2M Bronze.

Features:
The 2M Bronze features a Nude Fine Line diamond, which is particularly suited for demanding applications. The slim profile of the Fine Line stylus will track even the highest frequency information. Additionally, its larger footprint ensures reduced distortion and record wear. The 2M Bronze uses a special upgraded engine, featuring split pole pins with a silver plated copper wire.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5 mV
• Channel balance at 1 kHz - 1 dB
• Channel separation at 1 kHz - 26 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 + 2 / - 0 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 22 µm/mN
• Stylus type - Nude Fine Line
• Stylus tip radius - r/R 8/40 µm
• Tracking force range - 1.4-1.7 g (14-17 mN)
• Tracking force, recommended - 1.5 g (15 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.2 kOhm
• Internal inductance - 630 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Bronze
• 2MR cartridge weight - 6 g
• 2M and 2M Verso cartridges weight - 7.2 g
• 2M Premounted cartridge weight - 16.7 g

Replacement stylus unit - 2M Bronze (interchangeable with 2M Black and 2M Black LVB 250)

Stylus lifetime:
with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

2MR: the newest addition to the renowned 2M Series
Ortofon 2MR features a specially designed cartridge housing tailored for turntables and tonearms like Rega matching their requirement for low-form factor cartridges. With its narrow cartridge housing, it seamlessly integrates without a need for modifications or spacers under the tonearm, enabling quick and easy mounting with just two screws. Ortofon 2MR cartridges features unique to Ortofon technologies like: High-performance quad coil motor system with split pole pins, Proprietary Ortofon premium and high-end rubber dampers plus full compatibility with the Ortofon 2M series styli.

Authentic sound reproduction
2MR continues the 2M Series' commitment to authentic sound reproduction.
A high-performance motor system featuring quad coils and split pole pins minimizes eddy current losses, enhancing channel balance and accuracy.
This innovation results in a clean, detailed, and true-to-life sound, faithfully capturing the nuances of your cherished vinyl collection.

More than just a cartridge
2MR cartridge are for those who value an authentic immersive listening experience when listening to their music. 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.
The 2MR maintains the hallmark of interchangeability, allowing you to explore your records in greater depth and detail. The seamless transition between stylus profiles lets you tailor your listening experience, ensuring every note is heard with unparalleled accuracy and emotion. The 2MR series empowers you to explore your records like never before, allowing you to savor every moment of your favorite music.
The 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.

2MR cartridge key features:
• Slimline cartridge body effectively eliminates the need for tonearm spacers, shims or modifications on turntables needing a low form factor cartridge.
• High-performance motor system incorporating unique to Ortofon quad coils with split pole pins, delivering a clean detailed and true-to-life sound.
• 100% compatibility with the 2M styli Ortofon 2MR use the well-known 2M styli.
• Standard half inch mounting quick and easy mounting on the tonearms with just two screws.
• Full range setup 2MR ranges from Mono to Premium: 2MR Red to High-end: 2MR Black LVB 250

Step into the music with the 2M Red
With the 2M Red you will hear the music come to life on its own terms. It is like taking a step into music itself. This is our entry-level cartridge in the series, but what an entry.

Featues:
The 2M Red features a tipped Elliptical diamond and split pole pins with a copper wire.
The engine provides an increased output of 5.5 mV and an optimized sound reproduction and a high level of sonic accuracy.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Red delivers an open, dynamic sound with a slight touch of warmth.

Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 22 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 70 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Red
• 2MR cartridge weight - 6 g
• 2M and 2M Verso cartridges weight - 7.2 g
• 2M Premounted cartridge weight - 16.7 g

Replacement stylus unit - 2M Red (interchangeable with 2M Blue and 2M Silver)

Stylus lifetime:
with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

Stylus for Concorde MkII Elite Cartridge.

Exchangeable reinforced finger lift for Concorde MkII series
• Tapered shape, robustness where needed
• Metal ring is “unbroken”
• Colour options: Red, Black, Yellow and Orange
• Wider grip area
• Grip texture
• Graphics area

The new finger lift is one of the major improvements: it’s now stand alone replaceable part.

Available in Black, Red, Orange, Yellow and White colors which is perfect to personalize the cartridge the way you want it.

Introducing Concorde Music
Developed by music lovers, for music lovers, the Concorde Music cartridges blend premium performance with an iconic design.
Concorde Music, not just a cartridge, but a dedication to the profound impact music has on our lives, turning every listening session
into a captivating journey.

Possibly the world’s most iconic cartridge design
Building upon a rich legacy which began when we launched the original Concorde, the Concorde Music holds a storied history as
one of the most famous cartridges in the world of audio. Originally developed as a solution to the challenge of easy mounting on a
tonearm without screws or wires, the Concorde's unique design earned the Danish Industrial Design Award and became an icon in
the audio industry.

Features:
• Diamond: Each Concorde Music stylus features a diamond polished to the highest standards of the industry. Ranging from
a bonded Elliptical diamond on Concorde Music Red, to a Nude Shibata diamond on Concorde Music Black LVB 250.
• Cantilever: All Concorde Music models have a premium or high-end cantilever. The cantilever material is either aluminium
or boron for the best possible transmission of the vinyl record groove modulations picked up by the diamonds.
• Suspension: Exclusive Ortofon rubber compounds are used for the stylus suspensions, all carefully produced at the in_x0002_house own rubber production, and developed by the research and engineering team at Ortofon for brilliant performance.
• Coil system: Silver-pated oxygen free copper is chosen for the quad-coil system together with four Ortofon split pole pins
delivering a 6 mV output of dynamic, lifelike sound with an exceptional clarity and fidelity, capturing every detail.
• Upgradeability: All Concorde Music styli are compatible with all Concorde Music cartridges. An upgrade path is possible
through the entire series of Concorde Music cartridges, enabling upgrades from Concorde Music Red to Black LVB 250.
• Tool-free installation: Installing a Concorde Music cartridge on a turntable is easy and straightforward, no tools required
making it hassle free and convenient for all users.

It is all about the music
Concorde Music stands as an icon of design and musical dedication, inviting everyone to elevate their journey with the level of
accuracy in sound which has become characteristic for every Ortofon cartridge. Tailored for music lovers, incorporating a
straightforward installation, premium sound, and a timeless design. Concorde Music stands for a commitment to musicality.

Unique in-house rubber production a crucially important and vital part of a phono cartridge overall performance is the stylus
rubber suspension. Ortofon develops exclusive rubber compounds and produce the rubber suspensions and dampers in-house.

Ortofon quad-coil generating system with split pole pins in Concorde Music results in an exceptional channel balance and channel
separation, delivering a precise and dynamic sound image.

Ortofon, we love music!

Introducing Concorde Music
Developed by music lovers, for music lovers, the Concorde Music cartridges blend premium performance with an iconic design.
Concorde Music, not just a cartridge, but a dedication to the profound impact music has on our lives, turning every listening session
into a captivating journey.

Possibly the world’s most iconic cartridge design
Building upon a rich legacy which began when we launched the original Concorde, the Concorde Music holds a storied history as
one of the most famous cartridges in the world of audio. Originally developed as a solution to the challenge of easy mounting on a
tonearm without screws or wires, the Concorde's unique design earned the Danish Industrial Design Award and became an icon in
the audio industry.

Features:
• Diamond: Each Concorde Music stylus features a diamond polished to the highest standards of the industry. Ranging from
a bonded Elliptical diamond on Concorde Music Red, to a Nude Shibata diamond on Concorde Music Black LVB 250.
• Cantilever: All Concorde Music models have a premium or high-end cantilever. The cantilever material is either aluminium
or boron for the best possible transmission of the vinyl record groove modulations picked up by the diamonds.
• Suspension: Exclusive Ortofon rubber compounds are used for the stylus suspensions, all carefully produced at the in_x0002_house own rubber production, and developed by the research and engineering team at Ortofon for brilliant performance.
• Coil system: Silver-pated oxygen free copper is chosen for the quad-coil system together with four Ortofon split pole pins
delivering a 6 mV output of dynamic, lifelike sound with an exceptional clarity and fidelity, capturing every detail.
• Upgradeability: All Concorde Music styli are compatible with all Concorde Music cartridges. An upgrade path is possible
through the entire series of Concorde Music cartridges, enabling upgrades from Concorde Music Red to Black LVB 250.
• Tool-free installation: Installing a Concorde Music cartridge on a turntable is easy and straightforward, no tools required
making it hassle free and convenient for all users.

It is all about the music
Concorde Music stands as an icon of design and musical dedication, inviting everyone to elevate their journey with the level of
accuracy in sound which has become characteristic for every Ortofon cartridge. Tailored for music lovers, incorporating a
straightforward installation, premium sound, and a timeless design. Concorde Music stands for a commitment to musicality.

Unique in-house rubber production a crucially important and vital part of a phono cartridge overall performance is the stylus
rubber suspension. Ortofon develops exclusive rubber compounds and produce the rubber suspensions and dampers in-house.

Ortofon quad-coil generating system with split pole pins in Concorde Music results in an exceptional channel balance and channel
separation, delivering a precise and dynamic sound image.

Ortofon, we love music!

Introducing Concorde Music
Developed by music lovers, for music lovers, the Concorde Music cartridges blend premium performance with an iconic design.
Concorde Music, not just a cartridge, but a dedication to the profound impact music has on our lives, turning every listening session
into a captivating journey.

Possibly the world’s most iconic cartridge design
Building upon a rich legacy which began when we launched the original Concorde, the Concorde Music holds a storied history as
one of the most famous cartridges in the world of audio. Originally developed as a solution to the challenge of easy mounting on a
tonearm without screws or wires, the Concorde's unique design earned the Danish Industrial Design Award and became an icon in
the audio industry.

Features:
• Diamond: Each Concorde Music stylus features a diamond polished to the highest standards of the industry. Ranging from
a bonded Elliptical diamond on Concorde Music Red, to a Nude Shibata diamond on Concorde Music Black LVB 250.
• Cantilever: All Concorde Music models have a premium or high-end cantilever. The cantilever material is either aluminium
or boron for the best possible transmission of the vinyl record groove modulations picked up by the diamonds.
• Suspension: Exclusive Ortofon rubber compounds are used for the stylus suspensions, all carefully produced at the in_x0002_house own rubber production, and developed by the research and engineering team at Ortofon for brilliant performance.
• Coil system: Silver-pated oxygen free copper is chosen for the quad-coil system together with four Ortofon split pole pins
delivering a 6 mV output of dynamic, lifelike sound with an exceptional clarity and fidelity, capturing every detail.
• Upgradeability: All Concorde Music styli are compatible with all Concorde Music cartridges. An upgrade path is possible
through the entire series of Concorde Music cartridges, enabling upgrades from Concorde Music Red to Black LVB 250.
• Tool-free installation: Installing a Concorde Music cartridge on a turntable is easy and straightforward, no tools required
making it hassle free and convenient for all users.

It is all about the music
Concorde Music stands as an icon of design and musical dedication, inviting everyone to elevate their journey with the level of
accuracy in sound which has become characteristic for every Ortofon cartridge. Tailored for music lovers, incorporating a
straightforward installation, premium sound, and a timeless design. Concorde Music stands for a commitment to musicality.

Unique in-house rubber production a crucially important and vital part of a phono cartridge overall performance is the stylus
rubber suspension. Ortofon develops exclusive rubber compounds and produce the rubber suspensions and dampers in-house.

Ortofon quad-coil generating system with split pole pins in Concorde Music results in an exceptional channel balance and channel
separation, delivering a precise and dynamic sound image.

Ortofon, we love music!

Digitrack Limited Edition stylus
The Digitrack Limited Edition is the perfect marriage of easy and function. You can now manipulate MP3's with the style and feel of a turntablist and the tradition of a turntable. The Digitrack Limited Edition responds to the DJs who make extensive use of timecoded vinyl applications.

Digitrack Limited Edition low wear design and tailored frequency response increase the lifespan of timecoded vinyl records, and provides high quality sound reproduction for playing conventional vinyl records as well.

The Digitrack Limited Edition also features excellent groove-handling capabilities for scratch and mix performance, as well as increased output voltage for improved TCV performance and better sound quality from your mixer's phono preamps.

Digitrack Limited Edition Technical data
Output voltage at 1000Hz, 5cm/sec. - 8 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 22 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Frequency response - 20-18.000 Hz +3/-2 dB

Tracking ability at 315 Hz at recommmende tracking force - 90 μm
Compliance, dynamic lateral - 12 μm/m N
Stylus type - Spherical
Tracking force range - 2.0-4.0 g (20-40 mN)
Tracking force recommended - 3.0 g (30 mN)
Concorde cartridge weight - 18.5 g

Compatible with cartridges - Digitrack Limited Edition (discontinued and no longer available)

DJ E Replacement stylus
Basic model for scratch and back-cueing. Outstanding rigidity by extra-strengthened cantilever

Features Special Elliptical stylus and a special developed and extremely balanced cantilever.

Not only does the cartridge have a most sufficient tracking ability, it is also nearly unbreakable and provides the DJs with the most needed stringency. Furthermore, it equals very low record wear, an advantage for busy DJ.

The DJ series has been known to many as the "jack of all trades," with improved tracking, alongside of accurate sound reproduction. Featuring a low wear stylus design, the DJ provides excellent groove handling, even with less weight applied.

DJ E Stylus Technical data
Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel balance at 1kHz - 2 dB
Channel separation at 1kHz - 23 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-22.000 Hz
Frequency response - 20-20.000 Hz +/-2 dB
Tracking ability at 315 Hz at recommmende tracking force - 80 μm
Compliance, dynamic lateral - 9 μm/m N
Stylus type - Special Elliptical
Stylus tip radius - r/R 13/25 μm

Tracking force range - 2.0-4.0 g (20-40 mN)
Tracking force recommended - 3.0 g (30 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Concorde cartridge weight - 18.5 g

Compatible with cartridges - DJ S

rtofon DS-3 - a high precision digital stylus pressure gauge
DS-3 is a new lightweight compact digital stylus pressure gauge model. The DS-3 is a miniature ultra precision non-magnetic instrument that tunes your tonearm to the highest possible degree. The DS-3 scale is factory pre-calibrated for high accuracy measurements with the tolerance of +/-0.01 g.

How to use the DS-3
• Turn on the device by pressing ON button. The display will show 0000.
• Press the UNIT button to select the measurement unit. The default setting is gram/g.
• Place the stylus on the measurement plate on the right side of the device. Display will start blinking. It will stop blinking when the measurement is completed. The value displayed on the screen is the stylus pressure.
• The display screen will automatically dim to saving mode after 5 seconds of inactivity and turn off after 60 seconds of inactivity.
• When a battery runs out, a LO indicator will flash on the screen. Then replace both batteries.
• PCS button balances count by calculating the average weight of one piece-weight called a unit weight, then applying it to the total weight of what you are trying to count. Firstly, weigh one PC, then weigh the bundle, then push the PCS button and on the display you’ll get a number of PCS.

Technical data and precautions
Sensitivity - 0.01g
Operational weight range - 0.1g to 200g
Battery - 2 × AAA
Size - (L) 120mm × (W) 60mm × (H) 17mm
Weight - 70g
LCD screen with back lighting
Auto off function
Protect the device against high temperatures, dust and humidity
Carefully lower the measurement object on the measurement plate
Operating temperature range +10⁰ - +30⁰C
Do not place objects weighting more than 200 g on the measurement plate
Do not place the device on an uneven surface, it may result in not accurate measurements

Flight case for Ortofon Concorde MkII

Gold Replacement stylus
Perfect for usage in discotheques and clubs: provides the best possible sound quality available in a DJ cartridge!

Designed to commemorate the release of the limited edition Technics SL-1200LTD and SL-1200GLD, the Concorde Gold was made to compliment the attractive stylings of these limited edition turntables and to provide the best possible sound quality available in a DJ cartridge. Compatible to a very wide range of turntables.

Using the cartridge for the first time feels like striking gold. It is indeed the flagship product with its gold plating and special Pro E diamond. The Gold enjoys an excellent reputation for its amazing sound quality.

Available only with an elliptical stylus, the Concorde Gold is for DJs who will settle for nothing but the very best!

Technical data:
Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 23 dB
Channel separation at 15 kHz - 15 dB
Frequency response - 20-20.000 Hz +/- 2dB
Tracking ability at 315 Hz at recommended tracking force - 80 μm
Compliance, dynamic lateral - 7 μm/m N
Stylus type - Special Elliptical
Stylus tip radius - r/R 13/25 μm
Tracking force range - 2.0-5.0 g (20-50 mN)
Tracking force recommended - 3.0 g (30 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Concorde cartridge weight - 18.5 g

Compatible with cartridges - Gold (discontinued and no longer available)

GT Replacement stylus for tough handling - extremely sturdy for scratching DJs
GT was developed by Ortofon in close co-operation with SWS Audio GmbH. The cartridge was named "Great and Tough" and was based on the construction of the well-known Ortofon Series 500 design - mend for standard half inch mounting - in a black housing with white printing.

The vital parts in the GT are based on a very robust and reliable parts used in Scratch. Further, during development of GT, efforts were also concentrated on supplying a very high output of 8 mV and improvement of frequency response to give higher resolution and sound image.

Tracking avility is decisive for the DJs especially when scratching and back-cuing. In this situation raise of tracking force could be an immediate, but in many cases not very effective solution. The reason is that the antiskating adjustment, if not at a very moderate level, will double the skating effect when back-cuing.

As a rule, never use more than half of normal antiskating related to the tracking force! To make GT even more resistant against violent handling, such as drop or touch of fingers, we have made a rubber suspension of the cantilever even more rigid against axial pull.

GT Stylus Technical data
Output voltage at 1000Hz, 5cm/sec. - 8 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 25 dB
Channel separation at 15 kHz - 18 dB
Frequency range at -3dB - 20-20.000 Hz
Frequency response - 20-18.000 Hz +/- 2 dB
Tracking ability at 315 Hz at recommmende tracking force - 80 μm
Compliance, dynamic lateral - 6 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm

Tracking force range - 3.0-5.0 g (30-50 mN)
Tracking force recommended - 4.0 g (40 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1000 Ohm
Internal inductance - 580 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-400 pF

Compatible with cartridges - GT (discontinued and no longer available)

Comprises 1 PC carbon fibre stylus brush and 1 PC screwdriver in a plastic cylinder.

Lead Wires, set, 4 PCs

The LH-2000 is a basic high quality headshell designed specifically for HiFi applications. Providing a clean, minimalist aesthetic, the LH-2000 is great for a wide variety of cartridges, e.g. the 2M Series .

Knowing the fundamental headshell dimensions will in a lot of cases make it easier to mount and align cartridge and tonearm correctly. Please scroll to the bottom of the page to see the headshells mounting dimensions chart.

The LH-2000 comes with leadwires for easy and convenient connection
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell.

Please remember correct orientation of the leads. Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is only 1.0 mm.

Features and Technical data:
• Universal mount
• Solid aluminum build
• Weight without screws - 15.5 grams
• Mounting distance - min 35.3 mm, max 43.4 mm
• Headshell length - 50.3 mm
• Headshell width - 20.0 mm

The LH-4000 is a basic high quality headshell designed specifically for HiFi applications. Providing a clean, minimalist aesthetic, the LH-4000 is great for a wide variety of cartridges, specially recommended for the MC Quintet series.

Special features:
• Azimuth adjustable, which is beneficial for optimal channel separation
• Ergonomic fingerlift for easy handling
• Knowing the fundamental headshell dimensions will in a lot of cases make it easier to mount and align cartridge and tonearm correctly. Please scroll to the bottom of the page to see the headshells mounting dimensions chart.

The LH-4000 comes with leadwires for easy and convenient connection
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell.

Please remember correct orientation of the leads. Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is only 1.0 mm.

Features and Technical data:
• Universal mount
• Solid aluminum build
• Azimuth adjustable by means of hexagon wrench
• PIN conductor - Gold plated
• Weight - 14.3 grams without screws
• Mounting distance min. - 39.5 mm
• Mounting distance max. - 45.6 mm
• Headshell length - 51.9 mm
• Headshell width - 19.1 mm

Luxury leadwireset
LW-6N is the 6N lead wire made of Ultra High Purity Copper wire.
The configuration is very sofisticated with different diameter of wire strand, the inside strand is right windings, the outside strand is left winding. The end of wire is fastened by gold plated terminal.
The tight winding against each other makes the clear transmission of music signals. Clear and crisp tonality.

Technical data:
• High purity Cu wire 6NCu: 7 x φ 0.18mm (Right strands)
• High purity Cu wire 6NCu: 17 x φ 0.10mm (Left strands)

Mounting instructions:
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell. Please remember correct orientation of the leads. Ortofon SH-4 headshell and Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is normally only 1.0 mm.

Using LW 6N with the SH-4 headshell requies the LW 6N shell side clamp to be widened a little bit to fit on the SH-4 PINs. If shifted around, it may cause over-tightening of the assembly. Being aware about this detail, you will avoid the risk of having the cartridge's terminal PINs fall out.

Luxury leadwireset
LW-7N is the hybrid lead wire made of Ultra High Purity Copper wire of 7N and 6 N. The end of wire is fastened by Rhodium plated terminal.
As there is no foreign particle other than Copper 7N (99.99999 % purity) in the wire, music signal can be transmitted without any noise.

Technical data:
• High purity Cu wire 7NCu: 3 x φ 0.26mm
• High purity Cu wire 6NCu: 16 x φ0.10mm

Mounting instructions:
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell. Please remember correct orientation of the leads. Ortofon SH-4 headshell and Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is normally only 1.0 mm.

Using LW 7N with the SH-4 headshell requies the LW 7N shell side clamp to be widened a little bit to fit on the SH-4 PINs. If shifted around, it may cause over-tightening of the assembly. Being aware about this detail, you will avoid the risk of having the cartridge's terminal PINs fall out.

LW-800S is the most sophisticated lead wires composed of Pure Silver and Silver coated wire.
The end of wire is fastened by Rhodium plated terminal.
Since Silver has the best electrical conductive properties of all the metals, the LW-800S silver wire is able to transmits the very clear high tone signals, which brings the brilliant tonality to the sound reproduction.

Technical data:
• 4N Pure Silver wire: 3 x φ 0.26mm
• Silver plated Oxygen Free Copper (OFC) wire: 16 x φ0.10mm

Mounting instructions:
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell. Please remember correct orientation of the leads. Ortofon SH-4 headshell and Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is normally only 1.0 mm.

Using LW 8N with the SH-4 headshell requies the LW 8N shell side clamp to be widened a little bit to fit on the SH-4 PINs. If shifted around, it may cause over-tightening of the assembly. Being aware about this detail, you will avoid the risk of having the cartridge's terminal PINs fall out.

Enter the Exclusive world of Ortofon’s famous moving coil sound!
The Quintet Red is a perfect introduction to the world of Ortofon moving coils.
It features an Elliptical diamond which is cut and polished to Ortofon’s standards.

This entry-level MC cartridge has very high price-to-performance ratio and is a perfect all-rounder for the newcomers to the world of Moving Coil cartridges.

MC Quintet Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth.

The ST-7 transformer is a perfect match for the MC Quintet Red cartridge.

LH-4000 headshell is specially recommended for MC Quintet cartridges series.

MC Quintet Red Technical data:
• Output voltage at 1 kHz 5 cm/sec - 0.5 mV
• Channel balance - < 1.5 dB
• Channel separation at 1 kHz - > 21 dB
• Channel separation at 15 kHz - > 14 dB
• Frequency response 20-20.000 Hz - +/-2.5 dB
• Tracking ability at 315 Hz at recommended tracking force *) - 65 μm
• Compliance, dynamic, lateral - 15 μm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 μm
• Tracking force range - 2.1-2.5 g (21-25 mN)
• Tracking force recommended - 2.3 g (23 mN)
• Tracking angle - 20º
• Internal impedance, DC resistance - 7 Ohm
• Recommended load impedance - >20 Ohm
• Cartridge body material - ABS/Aluminium
• Coil wire material - Copper
• Cartridge colour - Red
• Cartridge weight - 9 g
*) Typical value

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for Quintet cartridge.

Ease of use
Top-mounting of the Quintet cartridges is easy and secure using the screws supplied. The aluminuim frame has threaded mounting holes and is fitted easily with the 5mm or 7mm screws depending on the thickness of the headshell.

The Quintet series’ right angles, straight lines, stylus visibility and ample distance between the record surface and the cartridge’s bottom will make it easy to mount and align the cartridge and tonearm correctly. The Quintet Series gives excellent results with most common tonearms.

Made From Scratch replacement stylus
To support our customers who own the Concorde MFS we will continue to manufacture replacement stylus MFS.

Features:
- Spherical stylus, which can stand up to heavy back-cueing
- High output for clear sound from a mixer/preamplifier
- Non-compromising energetic sound quality

Made From Scratch stylus Technical data
Output voltage at 1000Hz, 5cm/sec. - 7 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 25 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Frequency response - 20-15.000 Hz 3dB/-2dB
Tracking ability at 315 Hz at recommmende tracking force - 80 μm
Compliance, dynamic lateral - 6 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm

Tracking force range - 3.0-5.0 g (30-50 mN)
Tracking force recommended - 4.0 g (40 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Concorde cartridge weight - 18.5 g

Compatible with cartridges - Made From Scratch (discontinued and no longer available)

Nightclub E Replacement stylus
Nightclub E is equipped with Special Elliptical diamond. Perfect for usage in clubs. Superb sound quality.

Club DJs and studio workers believe the Nightclub E to be an absolute high-end cartridge. It is indeed a no-nonsence performer with fascinating musical resources.

It's output is superb with a frequency responce rating high enough to compare the Nightclub E to any audiophile cartridge.

The special elliptical stylus guarantees sound with insignificant scratching.

Nightclub E Stylus Technical Data
Output voltage at 1000Hz, 5cm/sec. - 8 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 23 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-22.000 Hz
Frequency response - 20-20.000 Hz +/- 1.5 dB
Tracking ability at 315 Hz at recommmende tracking force - 65 μm
Compliance, dynamic lateral - 20 μm/m N
Stylus type - Elliptical
Stylus tip radius - r/R 8/18 μm

Tracking force range - 2.0-5.0 g (20-50 mN)
Tracking force recommended - 3.0 g (30 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1000 Ohm
Internal inductance - 580 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Concorde cartridge weight - 18.5 g

Compatible with cartridges - Nightclub Series

Nightclub S Replacement Stylus
The Nighclub S stylus is amongst the top performers in its category, Scratch and Mix.

A spherical diamond and a customised design provide the basis for the cartridge's undeniable supremacy.

The stylus remains in the groove during the scratching and back-cueing, making it unfailingly reliable - even when giving a night-long performance.

Nightclub S Stylus Technical Data
Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 23 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-22.000 Hz
Frequency response - 20-18.000 Hz +3 / - 2 dB
Tracking ability at 315 Hz at recommmende tracking force - 80 μm
Compliance, dynamic lateral - 7 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm

Tracking force range - 2.0-5.0 g (20-50 mN)
Tracking force recommended - 3.0 g (30 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Concorde cartridge weight - 18.5 g

Compatible with cartridges - Nightclub Series

Optimal fit and sound reproduction
If your tonearm has a standard headshell or a cartridge mount, then step up to optimal sound reproduction with OM’s. A glance at anyone of these cartridges will reveal Ortofon's answer to perfect tonearm matching. Ingeniously tucked into the top of the mounting bracket is a tiny, removable weight-plate.

If your tonearm is an standard tonearm, just leave the weight-plate. If your tonearm is one of the low mass types, then simply remove the weight. The mass of your OM cartridge is now a mere 2.5g.

OM 5E features Elliptical stylus that provides balanced and distortion-free playback. Elliptical diamonds are able to follow the groove oscillations more accurately than spherical diamonds due to their contoured shape. This results in better tracking and less distortion.

• OM 5E Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4 mV
• Channel balance at 1 kHz - 2 dB
• Channel separation at 1 kHz - 22 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 3 / -3
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17.5 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 750 Ohm
• Internal inductance - 450 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 200-500 pF
• Cartridge colour, body/stylus - Black/Black
• Cartridge weight incl. extra weight - 5 g
• Cartridge weight excl. extra weight - 2.5 g
• Replacement stylus unit - Stylus 5E
*) Typical value

Styli types and interchangeability
By adopting a wide range of replacement styli, the OM 5 Series can provide an optimum match for your home system, application and budget.
In the development of OM cartridges, a major objective was to provide the music lover with the opportunity to optimize sound reproduction without having to replace the entire cartridge. Instead of being merely intended for replacement purposes following wear or damage, the OM 5 Series allows you to step up to better sound by simply upgrading the stylus. Depending on your preference, styli for the OM 5 Series are easily interchanged and include: styli 3E, 5E, 10, 20, 30, 40 & 78 and D 25 M.