Cartridges & Styluses 116 Items

Technical specifications:
• Frequency response - 20-12.000 Hz + 2 / - 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 15 µm/mN
• Stylus type - Spherical
• Stylus tip radius - 65µm
• Tracking force range - 1.75-2.25 g (17.5-22.5 mN)
• Tracking force, recommended - 2.0 g (20 mN)
• Tracking angle - 20°
• Stylus colour - Black
• Recommended for following cartridges: all Super OM, OM, OMB, OMP, TM, Concorde STD cartridges for playing 78 r.p.m. records
*) Typical value

Technical specifications:
• Frequency response: 20-18.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force *): 60 µm
• Compliance, dynamic, lateral: 25 µm/mN
• Stylus type: Elliptical
• Stylus tip radius: r/R 8/18 µm
• Tracking force range: 1.0-1.5 g (10-15 mN)
• Tracking force, recommended: 1.25 g (12.5 mN)
• Tracking angle: 20°
• Stylus colour: Black
• Recommended for TM 7 and TM 7U cartridges models
*) Typical value

Technical specifications:
• Frequency response - 20-18.000 Hz + 2 / - 3 dB
• Tracking ability at 315Hz at recommended tracking force *) - 60 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.5-2.0 g (15-20 mN)
• Tracking force, recommended - 1.75 g (17.5 mN)
• Tracking angle - 20°
• Stylus colour - Black
• Recommended for OM 3E, OMP 3E, OMB 3E
*) Typical value

The 2M 78 features an improved engine, which provides a high level of sonic accuracy. The stylus' tip is a Spherical diamond that is perfect for playback of 78 rpm shellac records, which require a larger stylus profile. The cartridge body is manufactured from Hopelex, which ensures high rigidity while eliminating unwanted resonances.

2M 78 uses a strapped output to deliver the same output signal from both sets of pole pins. This effectively eliminates the need for mono-specific equipment, making it possible to enjoy true mono reproduction on any stereo playback system.

The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M 78 Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 4 mV
• Frequency response - 20-20.000 Hz + 3 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 70 µm
• Compliance, dynamic, lateral - 18 µm/mN
• Stylus type - Spherical
• Stylus tip radius - R 65 µm
• Tracking force range - 1.6-2.0g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Internal impedance, DC resistance - 700 Ohm
• Internal inductance - 350 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Tracking angle - 20°
• Cartridge colour, body/stylus - Black/Grey
• Cartridge weight without screws - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M 78 (interchangeable with 2M Mono)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

Styli protection caps for VNL cartridges and styli

The stylus protection guard helps to limit stylus damage, if the cartridge accidentally slides across a record or if the cartridge is dropped onto the record.

The protection caps come in pairs.

Stylus for Ortofon VNL.

In ViNyL we trust
Even before the launch of the Concorde MkII, we have always studied the feedback of our customers and how they utilize our products.

Skilled DJs demand specialized tools that can help them push their creativity to the edge – consistently testing the boundaries in the realm of performance.

Understanding this and reflecting our extensive experience in industrial design and technological know-how, we present the new Ortofon VNL cartridge – a model tailored uniquely to the unrelenting demands of modern turntablists and portablists.

The new VNL features and improvements
• Extra resistance to hardcore scratching and back spinning
• High tracking performance for both DVS usage and real vinyl
• Optimal balance of output and of sound quality

Technological improvements have been applied for the benefits of all users:
- Ultrasonic welding of the components ensures high rigidity and freedom from resonances.
- Robotic assembly of stylus assembly offers high precision and uniformity of industrial production.

VNL \ compliance, dynamic lateral 16 μm/m N - Flexible

DJs can easily identify which stylus type best suits their individual DJ style and enables their absolute best performance capability.

VNL technical data

Stylus Type: Sperical
Tracking Force: 4,0 g
Output Voltage: 6mV
Frequency Range: 20-20.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel separation at 1kHz - 20 dB
Frequency response 20 Hz - 20 kHz -2/+4 dB
Tracking ability at 315 Hz at recommmended tracking force:

VNL I 100 μm

VNL I 16 μm/m N

Tracking force range - 3 - 5 g
Tracking force recommended - 4 g
Antiskating - for best backcueing performance use “0”
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Cartridge weight - 6,5 g
Replacement stylus units: VNL I, VNL II, VNL III

Exclusive features
The VNL features a spherical stylus which is perfect for tough groove handling. Furthermore, it reduces record wear when scratching and back-cueing to an absolute minimum.

The broad stance of the VNL features solid and robust design elements characteristic to Ortofon, with colors meticulously selected to emphasize sturdiness and DJ aesthetics: the cartridge body has been designed to provide easy mounting and alignment on a variety of headshells.

The VNL provides excellent compatibility when used in an assortment of playback systems, ensuring it stays in the groove under the most demanding conditions.

VNL Userguide: https://www.ortofon.com/media/151234/5-800161-12_vnl_userguide_08_20_web.pdf

The Goldring 1006 is designed for owners who want to get the very best from their systems at a budget price. This cartridge has an elliptical tip for improved high frequency clarity and a powerful magnet to ensure high sensitivity.

This hand-built cartridge features an elliptical stylus; its shape enables it to more accurately trace the highest frequency record grooves giving it the advantage over ordinary spherical types. The lightweight shank also gives the stylus a lower tip mass than cheaper metal bonded types lending the cartridge an improved transient response.

Low Mass Pocan® Body
The 1000 series uses a strong one piece body which holds the fixed parts securely in place. Made from a special type of ultra-rigid, glass reinforced polyester called Pocan, the body can be tightly bolted to the head shell for maximum efficiency and optimum sound quality. The user replaceable stylus carrier slots tightly into the body with a locating pin preventing unwanted vibrations which would otherwise colour the sound. An integral mu-metal can keeps the generator parts shielded from hum-inducing stray magnetic fields. Because Pocan has a high strength-to-mass ratio, the overall mass of the G1000 series cartridges is kept below 6.5 g. Low mass and moderate compliance keep the natural arm/cartridge resonance within safe limits for easy matching to a wide range of tonearms.

High Efficiency Magnetic Circuit
Finely etched mu-metal is laminated to form the pole pieces around which are fitted two formerless coils of four thousand turns each. This unique design reduces mass and also makes for a very efficient magnetic circuit producing a higher than average output. This construction also reduces the loss at high frequencies inherent in conventional designs, making for a smooth and extended frequency response.

Reduced Moving Mass
The 1000 series uses a unique ultra-low-mass, micro-miniature Alnico V magnet made to a tolerance that can be achieved by no other manufacturer worldwide. Welded to the magnet is a gold plated nickel tie-bar which provides an earth path for vinyl static charge build up and stabilses the cantilever in unwanted vibrational modes. The whole ultra-low-mass assembly is then mounted in a special butyl rubber polymer with optimised damping characteristics.

Expert Adjustment
The correct setting of stylus azimuth (or horizontal tracking angle) is essential for the maintenance of a proper stereo sound stage. Azimuth is the term used to describe the angle that the vertical centre-line of the stylus makes with the record surface and this must be exactly perpendicular to the record groove. This is not usually a user adjustable parameter on most budget decks and so it is vital that the cartridge leaves the factory with the azimuth precisely set. Badly adjusted azimuth can cause uneven channel balance and increased crosstalk between channels which would severely degrade the stereo image.

Specifications:
• Frequency Response: 20 Hz -20 kHz ±3 dB
• Channel Balance: within 2 dB @ 1 kHz
• Channel Separation: better than 25 dB @ 1 kHz
• Sensitivity: 6.5 mV ±1.5 dB, 1 kHz @ 5 cm/sec
• Static Compliance: 24 mm/N (lat); 16 mm/N (vert)
• Equivalent tip mass: 0.45 mg
• Vertical Tracking Angle: 24°
• Stylus Radius: Elliptical
• Stylus Type: Replaceable
• Load Resistance: 47 kΩ
• Load Capacitance: 150-200 pF
• Internal Inductance: 570 mH
• Internal Resistance: 660 Ω
• Cartridge Mass: 6.3 g
• Cartridge Mass (inc. fixings): 7.6 g
• Fixing Centre: 0.5" (12.7 mm)
• Playing Weight: 1.5 - 2.0 g (1.7 g nom.)
• Replacement Stylus: 1006 - D0

VM510CB
DUAL MOVING MAGNET STEREO CARTRIDGE WITH CONICAL STYLUS
Conical Bonded stylus
VM type dual magnet system
Para-toroidal coils improve generating efficiency
Aluminium cantilever
Centre shield plate between stereo channels
Durable low resonance polymer housing

Conical Bonded stylus for less critical tilt angle adjustment allowing more flexible use on various tonearms.
VM type dual magnet design ensures outstanding channel separation, extended frequency response and superb tracking
Lightweight tapered aluminium cantilever allows for faithful reading of the record groove
Centre shield plate enables the effective separation of left and right channels, suppressing electrical crosstalk to below 40dB
Durable low resonance polymer housing

Entry-level VM cartridge model equipped with a conical bonded stylus. The round stylus is less likely to be affected by placement and boasts stable tracing performance.

Aluminium cantilever
Para-toroidal coils improve generating efficiency
Centre shield plate between the left and right channels reduces crosstalk
Durable low resonance polymer housing

AUDIO-TECHNICA’S INTERNATIONALLY-PATENTED DUAL MAGNET DESIGN REPLICATES THE STRUCTURE OF THE CUTTER HEAD.
Instead of using a single, large magnet, the two magnets are arranged in the shape of a "V". The two magnets are positioned precisely to match the positions of the left and right channels in the stereo groove walls. Consequently, the VM design ensures outstanding channel separation, extended frequency response and superb tracking.

Para-toroidal generating system

Para-toroidal coils improve generating efficiency and offers superb linearity, since leakage of magnetic flux in this continuous and unitised magnetic circuit is low. Permeability of the cores is also optimised through the use of laminated cores.

Centre shield plate reduces crosstalk

A permalloy centre shield plate enables the effective separation of left and right channels, suppressing electrical crosstalk to below 40dB. This is similar to the actual crosstalk value found in the grooves of the record itself.

500 SERIES
Standard cartridge body fitted with the para-toroidal coils, centre shield plate, and 6N-OFC coil wire which is the same as 700 series.

CONICAL BONDED STYLUS
The benefit of conical styli, even if the cartridge is "lean", is the ball surface of the stylus touches the groove of vinyl records precisely. Due to its stability, it has been used widely at radio stations.

Type VM Type
Mounting 1/2” centres
Frequency Response 20 - 20,000Hz
Channel Separation 25dB (1kHz)
Output Channel Balance 1.5dB (1kHz)
Output Voltage 5.0mV (1kHz, 5cm/sec.)
Vertical Tracking Angle 23˚
Vertical Tracking Force Range 1.8 – 2.2g (2.0g standard)
Stylus Shape Conical Bonded
Stylus Size 0.6 mil
Stylus Construction Bonded Round Shank
Cantilever Aluminium Pipe
Coil Impedance 2,700Ω (1kHz)
Static Compliance 35 x 10-6 cm/dyne
Dynamic Compliance 8 x 10-6 cm/dyne (100Hz)
Recommended Load Impedance 47,000Ω
Recommended Load Capacitance 100 – 200pF
Weight 6.4g
Dimensions 17.3 (H) x 17.0 (W) x 28.2 (L) mm
Replacement Stylus VMN10CB
Accessories Included Cartridge installation screws 5mm ×2 and 10mm ×2, Washer ×2, Hexagon nut ×2

VM Cartridges: https://eu.audio-technica.com/resources/VM_Cartridges_EN.pdf

Manual: https://eu.audio-technica.com/resources/VM/VM510CB_UM_V2_11L_web_161011.pdf

Stylus for Concorde MkII Elite Cartridge.

GT Replacement stylus for tough handling - extremely sturdy for scratching DJs
GT was developed by Ortofon in close co-operation with SWS Audio GmbH. The cartridge was named "Great and Tough" and was based on the construction of the well-known Ortofon Series 500 design - mend for standard half inch mounting - in a black housing with white printing.

The vital parts in the GT are based on a very robust and reliable parts used in Scratch. Further, during development of GT, efforts were also concentrated on supplying a very high output of 8 mV and improvement of frequency response to give higher resolution and sound image.

Tracking avility is decisive for the DJs especially when scratching and back-cuing. In this situation raise of tracking force could be an immediate, but in many cases not very effective solution. The reason is that the antiskating adjustment, if not at a very moderate level, will double the skating effect when back-cuing.

As a rule, never use more than half of normal antiskating related to the tracking force! To make GT even more resistant against violent handling, such as drop or touch of fingers, we have made a rubber suspension of the cantilever even more rigid against axial pull.

GT Stylus Technical data
Output voltage at 1000Hz, 5cm/sec. - 8 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 25 dB
Channel separation at 15 kHz - 18 dB
Frequency range at -3dB - 20-20.000 Hz
Frequency response - 20-18.000 Hz +/- 2 dB
Tracking ability at 315 Hz at recommmende tracking force - 80 μm
Compliance, dynamic lateral - 6 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm

Tracking force range - 3.0-5.0 g (30-50 mN)
Tracking force recommended - 4.0 g (40 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1000 Ohm
Internal inductance - 580 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-400 pF

Compatible with cartridges - GT (discontinued and no longer available)

Replacement stylus Nagaoka JTS-80LB for the pickup JT-80LB.

Digitrack Limited Edition stylus
The Digitrack Limited Edition is the perfect marriage of easy and function. You can now manipulate MP3's with the style and feel of a turntablist and the tradition of a turntable. The Digitrack Limited Edition responds to the DJs who make extensive use of timecoded vinyl applications.

Digitrack Limited Edition low wear design and tailored frequency response increase the lifespan of timecoded vinyl records, and provides high quality sound reproduction for playing conventional vinyl records as well.

The Digitrack Limited Edition also features excellent groove-handling capabilities for scratch and mix performance, as well as increased output voltage for improved TCV performance and better sound quality from your mixer's phono preamps.

Digitrack Limited Edition Technical data
Output voltage at 1000Hz, 5cm/sec. - 8 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 22 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Frequency response - 20-18.000 Hz +3/-2 dB

Tracking ability at 315 Hz at recommmende tracking force - 90 μm
Compliance, dynamic lateral - 12 μm/m N
Stylus type - Spherical
Tracking force range - 2.0-4.0 g (20-40 mN)
Tracking force recommended - 3.0 g (30 mN)
Concorde cartridge weight - 18.5 g

Compatible with cartridges - Digitrack Limited Edition (discontinued and no longer available)