Cartridge Accessories 32 Items

Level Gauge - Basic
High precision gauge, calibrated.

Tonearm gauge
The easiest way to adjust the cartridge's Tracking Force.

Level Gauge - Stainless steel
High precision gauge, calibrated.

Stylus protection guard (1 Pcs.) for the MC Quintet Series.

Comprises 1 PC carbon fibre stylus brush and 1 PC screwdriver in a plastic cylinder.

Luxury leadwireset
LW-6N is the 6N lead wire made of Ultra High Purity Copper wire.
The configuration is very sofisticated with different diameter of wire strand, the inside strand is right windings, the outside strand is left winding. The end of wire is fastened by gold plated terminal.
The tight winding against each other makes the clear transmission of music signals. Clear and crisp tonality.

Technical data:
• High purity Cu wire 6NCu: 7 x φ 0.18mm (Right strands)
• High purity Cu wire 6NCu: 17 x φ 0.10mm (Left strands)

Mounting instructions:
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell. Please remember correct orientation of the leads. Ortofon SH-4 headshell and Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is normally only 1.0 mm.

Using LW 6N with the SH-4 headshell requies the LW 6N shell side clamp to be widened a little bit to fit on the SH-4 PINs. If shifted around, it may cause over-tightening of the assembly. Being aware about this detail, you will avoid the risk of having the cartridge's terminal PINs fall out.

Luxury leadwireset
LW-7N is the hybrid lead wire made of Ultra High Purity Copper wire of 7N and 6 N. The end of wire is fastened by Rhodium plated terminal.
As there is no foreign particle other than Copper 7N (99.99999 % purity) in the wire, music signal can be transmitted without any noise.

Technical data:
• High purity Cu wire 7NCu: 3 x φ 0.26mm
• High purity Cu wire 6NCu: 16 x φ0.10mm

Mounting instructions:
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell. Please remember correct orientation of the leads. Ortofon SH-4 headshell and Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is normally only 1.0 mm.

Using LW 7N with the SH-4 headshell requies the LW 7N shell side clamp to be widened a little bit to fit on the SH-4 PINs. If shifted around, it may cause over-tightening of the assembly. Being aware about this detail, you will avoid the risk of having the cartridge's terminal PINs fall out.

LW-800S is the most sophisticated lead wires composed of Pure Silver and Silver coated wire.
The end of wire is fastened by Rhodium plated terminal.
Since Silver has the best electrical conductive properties of all the metals, the LW-800S silver wire is able to transmits the very clear high tone signals, which brings the brilliant tonality to the sound reproduction.

Technical data:
• 4N Pure Silver wire: 3 x φ 0.26mm
• Silver plated Oxygen Free Copper (OFC) wire: 16 x φ0.10mm

Mounting instructions:
All Ortofon cartridges have a colour coding of the terminals, indicating red and green for right channel respectively hot and ground terminal. White and blue for left channel respectively hot and ground terminal. Green terminal will always be used for grounding the cartridge housings or motor-system, whenever connected inside the cartridge.

We recommend to connect lead wires to the cartridge and headshell before mounting the cartridge on the headshell. Please remember correct orientation of the leads. Ortofon SH-4 headshell and Ortofon cartridges' terminal PINs diameter is 1.2 mm, whilst Ortofon headshells' PINs diameter is normally only 1.0 mm.

Using LW 8N with the SH-4 headshell requies the LW 8N shell side clamp to be widened a little bit to fit on the SH-4 PINs. If shifted around, it may cause over-tightening of the assembly. Being aware about this detail, you will avoid the risk of having the cartridge's terminal PINs fall out.

Styli protection caps for VNL cartridges and styli

The stylus protection guard helps to limit stylus damage, if the cartridge accidentally slides across a record or if the cartridge is dropped onto the record.

The protection caps come in pairs.

Stylus guard (1 Pcs.)

Tool for OM mounting

Spirit level

Spirit level for optimum positioning of a turntable.

Electronic stylus balance

The Measure it S2 Stylus Tracking Force Gauge is a highly accurate electronic balance that is designed for measuring stylus trackingforces up to 5.0 grams in 0.001 gram increments. Each Measure it S2 can easily be calibrated with the included calibration weight. The Measure it S2 has a solid aluminum housing with a 4-digit LCD backlit display. Whenever in doubt about the actual amount of pressure on the diamond tip the 4 digit display of this smart tool will help. Armed with precise information about tracking force, your stylus tip wear can be significantly reduced.

Scope of delivery:
• stylus balance
• calibration weight
• screwdriver
• 2x AAA batteries
• protection case for the meter
• user guide

Features:
• 4 digit LCD-Display with backlight
• Capacity 0 - 5g
• Variance ±0,001g
• Auto calibration function
• Auto off after 60 seconds
• Replacement batteries supplied

Technical Specifications:
• Capacity: 0 - 5g
• Variance: ±0,001g
• Weighting modes: gram (1g = 10mN), ounce (oz), pennyweight (dwt) and carat (ct)
• Display: 4 digit LCD with backlight
• Calibration: Auto calibration using a 5g weight
• Auto off: 60 seconds off
• Replacement battery: 2 x AAA cells, 1,5V
• Operating temperature: +10 - +30°C (50 - 86 degrees Fahrenheit)
• Dimensions (W x H x D): 122 x 27 x 55mm
• Weight: 170g

Cartridge alignment tool

• Tool for cartridge alignment and adjustment
• Special slip-proof tool for defining the turning centre of Pro-Ject tonearms
• Adaptable to accommodate differing tonearm lengths
• Also suitable for other manufacturers’ tonearms
• Suitable for tonearms between 8″ (203mm) and 12″(305mm) effective length

Lead Wires, set, 4 PCs

Ortofon fibre brush for cleaning the stylus
For cleaning the stylus, use fiber brush a few times along the cantilever in the direction of the stylus, whenever you play a new record or change sides.

Rubber ring for Concorde cartridge
Rubber rings function is to prevent over-tighten of the cartridge assembly on the tonearm, over-tighten can push the tonearm contacts back. The rubber ring should be pushed to the base of the cartridge assembly, position between the cartridge connector(rare) and the tonearm.

Height: 0.8 mm

Rubber rings, pair

Extra weight for Ortofon OM cartridge
Specifications:

- Weight: 2.5 g
- Material: Brass

Styli protection caps, pair

Ortofon HiFi Maintenance set
Comprises 1 PC fibre stylus brush and 1 PC screwdriver in a plastic cylinder.

rtofon DS-3 - a high precision digital stylus pressure gauge
DS-3 is a new lightweight compact digital stylus pressure gauge model. The DS-3 is a miniature ultra precision non-magnetic instrument that tunes your tonearm to the highest possible degree. The DS-3 scale is factory pre-calibrated for high accuracy measurements with the tolerance of +/-0.01 g.

How to use the DS-3
• Turn on the device by pressing ON button. The display will show 0000.
• Press the UNIT button to select the measurement unit. The default setting is gram/g.
• Place the stylus on the measurement plate on the right side of the device. Display will start blinking. It will stop blinking when the measurement is completed. The value displayed on the screen is the stylus pressure.
• The display screen will automatically dim to saving mode after 5 seconds of inactivity and turn off after 60 seconds of inactivity.
• When a battery runs out, a LO indicator will flash on the screen. Then replace both batteries.
• PCS button balances count by calculating the average weight of one piece-weight called a unit weight, then applying it to the total weight of what you are trying to count. Firstly, weigh one PC, then weigh the bundle, then push the PCS button and on the display you’ll get a number of PCS.

Technical data and precautions
Sensitivity - 0.01g
Operational weight range - 0.1g to 200g
Battery - 2 × AAA
Size - (L) 120mm × (W) 60mm × (H) 17mm
Weight - 70g
LCD screen with back lighting
Auto off function
Protect the device against high temperatures, dust and humidity
Carefully lower the measurement object on the measurement plate
Operating temperature range +10⁰ - +30⁰C
Do not place objects weighting more than 200 g on the measurement plate
Do not place the device on an uneven surface, it may result in not accurate measurements

Exchangeable reinforced finger lift for Concorde MkII series
• Tapered shape, robustness where needed
• Metal ring is “unbroken”
• Colour options: Red, Black, Yellow and Orange
• Wider grip area
• Grip texture
• Graphics area

The new finger lift is one of the major improvements: it’s now stand alone replaceable part.

Available in Black, Red, Orange, Yellow and White colors which is perfect to personalize the cartridge the way you want it.

Flight case for Ortofon Concorde MkII

One-Touch Polymer
Stylus Tip Dry Cleaning System

STYLUS TIP Dry Cleaning System
• Made from an innovative solid polyurethane (PU) polymer.
• Ultra-soft, highly elastic and strong adhesive ability to keep the Stylus in pristine condition.
• Liquid-free. Solvent-free

Winyl One-Touch contains an innovative solid polyurethane (PU) polymer, specially designed to provide exceptional cleaning for record player stylus needles to ensure top quality sound.

The polymer is soft and highly elastic, with strong adhesive properties to remove dust and microscopic dirt, reducing surface noise and distortion on the playback. In addition, its cleaning system allows to clean the corner-gap between cantilever and stylus.
The polymer has been developed to ensure that it leaves no residue on the stylus, due to its dry-cleaning system, liquid-free.

One-Touch is safe and easy-to-use. Place the headshell above the polymer, lower the cartridge slowly until the stylus needle is inserted into the polymer, lift it up. The dirt will adhere to the polymer surface, leaving the needle clean.

One-Touch Polymer is washable and reusable. If the surface of the polymer becomes heavy soiled after repeated uses, simply rinse it with tap water and rub gently the surface with a finger to loosen dirt. Drain and let dry. The polymer will recover its cleaning properties to use it again. By keeping One-Touch in good condition, you will be able to use it for years with the same effectiveness as the first day.

PS Clear Case 41 x 40 x 15 mm
Polymer 30 x 30 x 3 mm (PU sheet)

• Made in Spain

Manual Videos:
https://www.youtube.com/watch?v=Eb-QxvH2Ezk
https://www.youtube.com/watch?v=zkPnvE6gHog

AT617A - CARTRIDGE STYLUS CLEANER
- Specially formulated polyurethane gel removes dirt particles from stylus
- Gel remains tacky for years
- Surface is washable for repeated use